Kleenmaid K70 User Manual

CookingCooking

c o l l e c t i o nc o l l e c t i o n

Instructions for Use

and

Warranty Details

Professional Series

Rangehoods

ongratulations on the purchase of your new

C

appliance. This appliance has been

designed and manufactured to give you years

of reliable performance.

For best results, carefully read the instructions on

how to install your new appliance. Correct installation

will avoid delays and unnecessary service calls.

Once installation is complete, read this booklet

carefully and get to know the controls and the

features of your new appliance.

We reserve the right to alter the specifications

with no influence on the operation of the

appliance. This instruction manual cannot be

reason for a claim.

Contents



1. Warnings for safety and use ________________________________ 4

2. General information ______________________________________ 5

2.1 Servicing and assistance ____________________________________________________ 5

3. Installation______________________________________________ 6

3.1 Electric connection _________________________________________________________ 9

4. Description of the hood ___________________________________ 10

5. Description of controls____________________________________ 11

5.1 Control panel ____________________________________________________________ 11

6. Cleaning and maintenance ________________________________ 12

6.1 Cleaning stainless steel surfaces_____________________________________________ 12

6.2 Cleaning the metallic greaseproof filter ________________________________________ 12

6.3 Replacing bulbs __________________________________________________________ 13

INSTRUCTIONS FOR THE INSTALLER:

in charge of installation and appliance commissioning.

INSTRUCTIONS FOR THE USER:

correct cleaning and maintenance operations for the appliance.

these instructions are intended for the

include suggestions, the description of the controls and the

qualified installer

Warnings

1. Warnings for safety and use

THE PRESENT MANUAL IS INTEGRAL WITH THE APPLIANCE AND MUST HENCE BE PROPERLY MAINTAINED
INTACT AND ALWAYS KEPT WITHIN EASY REACH THROUGHOUT APPLIANCE WORK LIFE. BEFORE USING THE
SUCTION APPLIANCE, WE RECOMMEND READING THIS MANUAL AND ALL THE INDICATIONS IT CONTAINS
THOROUGHLY.

PREVAILING STANDARDS.

BUILT IN COMPLIANCE WITH PREVAILING

HELD RESPONSIBLE FOR ANY ACCIDENT THAT MAY BE CAUSED BECAUSE OF IMPROPER USE.

DO NOT LEAVE ANY PIECES OF THE PACKAGING UNATTENDED IN THE HOME. SEPARATE THE VARIOUS
PACKAGING MATERIALS AND DELIVER THEM TO THE NEAREST RECYCLING CENTRE.

THE EARTH CONNECTION IS MANDATORY AND MUST CONFORM TO THE CURRENT AUSTRALIAN STANDARDS
OF THE ELECTRICAL WIRING SYSTEM.

INSTALLATION IS TO BE CARRIED OUT SOLELY BY QUALIFIED PERSONS ACCORDING TO

APPLIANCES HEREUNDER ARE INTENDED SOLELY FOR DOMESTIC USE AND ARE

E.E.C.

AND

E.U. DIRECTIVES. THE MANUFACTURER SHALL NOT BE

THE PLUG TO BE CONNECTED TO THE POWER SUPPLY CABLE AND THE RELATIVE SOCKET MUST BE THE
SAME TYPE AND MUST COMPLY WITH CURRENT STANDARDS. AFTER INSTALLING THE APPLIANCE MAKE SURE
THAT THE PLUG IS ACCESSIBLE TO ALLOW THE PERIODICAL CHECK-UP.

DO NOT PULL OUT THE PLUG BY PULLING THE CABLE.

IMMEDIATELY AFTER INSTALLATION, TEST THE APPLIANCE BRIEFLY BY FOLLOWING THE INSTRUCTIONS
SHOWN BELOW. IN THE EVENT OF A MALFUNCTION, DISCONNECT THE APPLIANCE FROM THE MAINS AND
CONTACT YOUR NEAREST TECHNICAL SERVICE CENTRE.

DO NOT ATTEMPT TO REPAIR THE APPLIANCE.

THE IDENTIFICATION PLATE, WITH THE TECHNICAL DATA, SERIAL NUMBER AND MARKING, CAN BE FOUND
INSIDE THE APPLIANCE.

THE PLATE MUST NEVER BE REMOVED.

THE APPLIANCE IS INTENDED FOR USE SOLELY BY ADULTS.

APPLIANCE OR TO PLAY WITH THEM. BE CAREFUL NOT TO LEAVE OBJECTS ON THE APPLIANCE THAT MAY
ATTRACT CHILDREN’S ATTENTION. ALWAYS KEEP CHILDREN AT A SAFE DISTANCE FROM THE APPLIANCE. THE
APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM PERSONS WITHOUT SUPERVISION.

DISCARDED APPLIANCES MUST BE DELIVERED SOLELY TO A SPECIALISED WASTE COLLECTION CENTRE.

NEVER ALLOW CHILDREN TO COME NEAR THE

The manufacturer shall not be held responsible for any injury or damage that may be caused
by failure to fully comply with the aforementioned instructions and recommendations or by
tampering with the appliance components or the use of non-original spares.



Warnings



2. General information

This product conforms to the requirements of the following European directives:

73/23/EEC

•

89/336/EEC

•

for "Low Voltage".

for "Electromagnetic Disturbance".

The above mentioned directives also conform to

The hood is fitted with a motor with adjustable speed. To obtain the best efficiency, we recommend
using the low speeds in normal conditions and the high speeds with a high concentration of odours
and steam.

It is advisable to switch on the hood a few minutes before cooking and to leave it on after cooking
has finished, until all odours have disappeared.

Cooking food on a flame under the hood is strictly forbidden.

Using naked flame damages the filters and may cause a fire, therefore it should be avoided.

Always watch over the pan when frying to prevent overheated oil from catching fire.

Machine directive 98/37/EC

.

2.1 Servicing and assistance

All outgoing appliances undergo rigorous factory testing and inspection by expert and specialised
personnel and are hence guaranteed in perfect operating conditions. Any subsequent repairs or
adjustments must be performed with utmost care and attention. In such an event please contact
your nearest Kleenmaid Store or authorised dealer from which the appliance was purchased on
13 13 08 or your nearest authorised Kleenmaid service agent on 1300 652 100 specifying the
problem encountered and the model of the appliance.

The following models are covered by these instructions

K70

- 700mm Stainless Steel Wallmounted

K90

- 900mm Stainless Steel Wallmounted

K100

- 1000mm Stainelss Steel Wallmounted

K120

- 1200mm Stainless Steel Wallmounted

Instructions for the installer

3. Installation

Only qualified installers are authorised to carry out the operations described below. The
professional installer is responsible for appliance commissioning in accordance with
prevailing standards and requirements under law.

protections before using the appliance.

The manufacturer declines any responsibility for damage incurred by persons, animals or
objects that is caused by not following the above guidelines (Refer to “1. Warnings for
safety and use”).

Switch off the power supply to the appliance before starting the installation.

The hood is provided with an upper air outlet B for discharging the fumes outside (

version

The hood is fitted with fastening dowels suitable for most walls/ceilings. A qualified technician
should however be called to ensure the materials are suitable for your wall/ceiling. The wall/ceiling
must be strong enough to withstand the weight of the hood.

; venting pipe and clamps not supplied).

Always remember to remove plastic

suction



Instructions for the installer



•

Remove the grease filter(s).

•

When installed, the lower side of the hood should be at least
electric or mixed hobs or

750mm

if installing above any of the following splashbacks. SK70

SK90 SK100 SK120.

1.

Drill six holes (

2.

Hang the hood onto the 2 upper hooks.

3.

Fasten the hood to the wall definitively using the 4 remaining dowels, previously inserted into
the wall, with 4 screws

4.

Connect a venting pipe (

PLEASE NOTE:

•

When using the

Ø 8 mm

), insert 6 dowels and tighten only the 2 central hook dowels at the top.

(compulsory)

150 mm

.

) to the connection ring above the suction motor unit.

Venting pipe and clamps are not supplied with hood.

suction version

of the hood, the other end of the venting pipe must be

connected to a device that extracts fumes to the outside.

•

Connect the electrics.

•

Rest the lower section of the stack onto the top of the hood that covers the suction motor
compartment and fit it into its housing.

•

Insert the upper section of the stack into the lower section and check that the sides with the
holes face upwards.

5.

Fasten the upper bracket close to the ceiling (use the bracket as a drilling plan), pencil in two

.

Ø 8 mm

) and insert 2 wall dowels. Fasten the upper bracket with 2

holes, drill the holes (
screws

6.

Fasten the upper section of the stack to the bracket with 2 screws (one on each side).

•

5x45 mm

Refit the grease filter(s) and check the hood is in good working order.

650mm

above either gas,

Instructions for the installer

Never use the hood if the filter is not correctly fitted!

The sucked out air must not be conveyed into a duct used for discharging the fumes from devices
powered with energy other than electricity. The room must always be adequately aired when a
hood and devices powered with energy other than electricity are used at the same time.

Always adhere closely to the guidelines set out by the competent local authorities for the technical
and safety measures to adopt for discharging fumes.

Cooking fumes and steam are expelled through a venting pipe that is fastened to the connection
ring above the hood. The venting pipe must have exactly the same diameter as the connection
ring.

In horizontal sections, the pipe must be slightly tilted upwards (
easily conveyed outside the room.

Always keep closely to the instructions given in this manual. No responsibility is accepted
for any problems, damage or fire caused to the appliance due to failure to observe the
instructions given in this manual.

approx. 10%

) to allow the air to be



Instructions for the installer



3.1 Electric connection

Prepare an omni-polar cutoff device on the power supply line of the appliance with a contact
opening distance equal to or more than

The plug at the end of the power supply cable and the wall socket must be the same type and must
comply with current electric standards. Check that the mains is adequately earthed. Once the
appliance has been installed make sure that the plug is accessible to allow the periodical check-up.

Do not use reducers, adapters or shunts.

Before making any connection, make sure that the mains voltage corresponds to the voltage
shown on the specifications label inside the appliance. It is essential to have a qualified technician
make the electric connection.

3 mm

, located in a convenient position near the appliance.

The plate must never be removed.

Make sure that the circuit breaker and the home wiring system are able to withstand the appliance
load.

The yellow/green earth cable must not be subject to cutoffs.

The electric cable must not come into contact with parts whose temperature is more than
higher than room temperature.

3.1.1 Appliance fitted with plug

If you wish to connect the appliance directly to the mains, unplug it and fit a standard double-pole
switch with the break contacts at a distance of no less than
the socket, is not in an accessible position, a standard double-pole switch should nevertheless be
fitted with the break contacts at a distance of no less than

3.1.2 Appliance without plug

Fit a standard plug or a standard double-pole switch with the break contacts at a distance of no
less than

3 mm

.

3 mm

3 mm

. If the plug, once plugged into

.

50°C

Instructions for the user

4. Description of the hood



1

2

3

4

5

6

7

8

Telescopic stack

Stack

Hood structure

Motor

Control panel

Metallic greaseproof filters

Installation kit

Halogen light

Instructions for the user

5. Description of controls

5.1 Control panel

5.1.1 Manual mode

LIGHT BUTTON:

SPEED REDUCTION BUTTON:

inside the button turns

ON/OFF BUTTON:

last speed with which it was used. The LED inside the button turns
After approximately
must be cleaned. To stop the flashing press and hold down the
or switch off the power supply.

hours and the LED turns green.

SPEED INCREASE BUTTON:

inside the button turns

TIMER:

requested speed, after which it switches off completely. When in operation, the LED inside the
button is

on pressing this button, the hood continues to operate automatically for

orange

press this button to switch on the lights and the LED inside the button turns

press this button to reduce the speed of the motor and the LED

green

. When the speed is on minimum, the LED begins to flash.

press this button to switch on the motor and the hood begins to operate at the

40 consecutive operating hours

This operation resets the count of the 40 consecutive operating

press this button to increase the speed of the motor and the LED

green

. When the speed reaches maximum level, the LED begins to flash.

.

green

, the LED flashes to advise that the filters

ON/OFF

.

button for a few seconds

10 minutes

blue

at the

.

5.1.2 Automatic mode

This mode is recommended for intensive use of the hood (two or three burners on). Otherwise, with
just one burner on, the manual mode is recommended.

In automatic mode, the motor speeds are activated automatically by a heat sensor positioned
inside the hood.

To start the automatic mode, press the speed increase and speed reduction buttons at the same
time. The
approximately thirty seconds.
The hood starts in automatic mode and the heat sensor automatically adjusts the speed of the
motor to the temperature produced by the burners.
To return to manual mode, press the

The correct operation of the
suction surface of the hood: the higher the hood is positioned, the more difficult it will be for the
sensor to identify the temperature.

orange LED

switches on and the

ON/OFF

heat sensor

three central green LEDs

button.

depends on the distance between the hob and the

begin to flash after



Instructions for the user

6. Cleaning and maintenance

Switch off the power supply to the appliance before starting the installation.
This operation resets the count of the 40 consecutive operating hours and the ON/OFF LED
turns green.

Do not clean the surfaces of the appliance when they are still hot.
Do not use pressure or steam spray guns to clean the appliance.

Failure to clean the hood and replace and clean the filters as described generates a fire
hazard. Please keep to the instructions given.

6.1 Cleaning stainless steel surfaces

To clean, use a standard cleaner designed for stainless steel. We recommend Kleenmaid Stainless
Steel cleaning products available from your nearest Kleenmaid Store. Always follow the
manufacture instructions.

Do not under any circumstances use metallic sponges, sharp scrapers, steel wool or rough
sponges. They will damage the surfaces. Use scratchproof, non-abrasive sponges only.

To clean

glossed

stainless steel parts, wipe the cloth in the direction of the glossing.

6.2 Cleaning the metallic greaseproof filter

•

To disassemble the metallic greaseproof filter, use the special spring-release handles by
pulling them first back (A) and then downwards (B).

•

After cleaning the metallic greaseproof filters, leave to dry and follow the above instructions in
reverse order to refit them.

Take care not to damage the filters while refitting them.

At the end of this operation, the count of the

by pushing the ON/OFF

button for a few seconds or by switching off the power supply.

40 consecutive operating hours

must be reset



The metallic greaseproof filter has unlimited duration and must only be cleaned by hand or in the
dishwasher (
greaseproof filter may become discoloured but its filtering characteristics are unchanged.

The metallic greaseproof filters must be washed at least once a month.

65°C

), with suitable detergents. When cleaning in the dishwasher, the metallic

Instructions for the user



6.3 Replacing bulbs

Proceed as follows:

•

prise up the protection using a small flat-head screwdriver or
similar tool;

•

replace the damaged bulb. Use only halogen lights
(G4), taking care not to touch them with the hands;

•

close the light cover (snap shut).

If the lights do not work, check the bulbs are correctly inserted into their housings before
calling a technician.

max 20W



Notes

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

7.



WARRANTY AND SERVICE

DOMESTIC WARRANTY - FULL FIVE YEAR WARRANTY

In addition to all statutory rights which you, the Consumer, have under the relevant laws in respect
of this appliance, during the first five years of ownership as the original purchaser of this
Kleenmaid appliance, we guarantee that any fault caused by faulty material or workmanship
becoming apparent will be rectified free of charge for parts and labour, provided that all service is
performed during normal working hours by Kleenmaid or their designated Agents. Where the
appliance is installed outside the normal servicing area of the above, the Purchaser must pay for
the cost of transporting the appliance to and from the Agent or the Agent’s travelling cost to and
from the Purchaser’s home.

COMMERCIAL WARRANTY - ONE YEAR WARRANTY

When this appliance is installed in a commercial application, you, the Consumer, have under the
relevant laws in respect of this appliance, during your first one year of ownership as the original
purchaser of this Kleenmaid appliance, we guarantee that any fault caused by faulty material or
workmanship becoming apparent, will be rectified free of charge for parts and labour, provided that
all service is performed during normal working hours by Kleenmaid or their designated Agents.
Where the appliance is installed outside the normal servicing area of the above, the Purchaser
must pay for the cost of transporting the appliance to and from the Agent or the Agent’s travelling
cost to and from the Purchaser’s home.

WHAT THESE WARRANTIES DO NOT COVER

We are not responsible for any damage or malfunction unless caused by a defect in material or
workmanship. This includes but is not limited to abuse, misuse, improper installation and
transportation damage. We are not responsible for any consequential damages from any
malfunction.
The Consumer must make the appliance available for servicing and shall bear any costs incurred
for any de-installation and/or re-installation required to make the appliance available for servicing.
Kleenmaid is not liable for any consequential damage incurred during de-installation or re­installation.

WARRANTY DOES NOT COVER REPLACEMENT OF LIGHT
GLOBES OR GLASS BREAKAGE DUE TO IMPACT

In case of fractured glass do not use your appliance.

WARRANTY REGISTRATION

Please complete warranty details below. Please retain together with your proof of purchase document.
These documents will need to be viewed by our Service Representative should you request in warranty
service.

SERVICE ASSISTANCE

To assist you when phoning our After Sales Service number to arrange a service call please complete
the following details and have them ready when you call.

Model Number_____________________________Date of purchase____________________________

Kleenmaid Store purchased from_________________________Date of installation ________________

KLEENMAID AFTER SALES SERVICE

1300 652 100

Other products available in the Kleenmaid

Range of appliances

Washers

Dryers

Dishwashers

Ovens

Cooktops

Outdoor Cooking Centres

Built In Coffee Machines

Rangehoods

Freestanding Ranges

Sinks

Waste Disposals

Taps

Cookware

Refrigerators

Freezers

Wine Cellars

Vacuum Cleaners

For sales information on the full range of quality appliances

Phone 13 13 08

07/04 ZS1969