Kleenmaid IB61 User Manual

Page 1
9960 3732 04/98
use / installation
REF CONSTRUCTEUR 214
Type IB 61
220/240V - 50/60Hz 5600W
IB 61
87x 1134
INDUCTION
Page 2
1/2 VERY LOW melting butter, chocolate,
keeping warm sauces, custards...
3 SLOW rice pudding
reheating
4/5 SIMMER purée, pulses, soups,
jam, compotes
6 MEDIUM pasta, boiled rice,
boiling milk
7/8 HIGH steaks, fast frying, pancakes
9 VERY HIGH deep frying, fast boiling
Page 3
1
How induction works
For the user
Congratulations on choosing an induction hob, a system which is
revolutionising cooking.
With your hob, because the heat required to cook the food is produced directly in the interior of the pan, the ceramic top barely becomes hot for it receives ONLY the heat from the pan placed on it.
Compared to a standard hob your induction hob is:
- MORE ECONOMICAL: when a pan is removed the heating zone switches off instantly.
- FASTER: output of 2800 W available instantly on the heating zone
- MORE PRECISE: the hob reacts instantly to the controls
- SAFER: the temperature of the ceramic top remains low
Operating principle:
The “induction” currents instantly heat the pan* which transfers its heat to the food it contains.
*Enamelled steel, cast iron or stainless steel pans are suitable for induction cooking.
Pan
Inducted currents
Electronic circuit
Electrical supply
Page 4
2
Layout
For the user
Display showing (1 to 9) the power level set for each heating zone.
Symbol indicating the heating zone on the hob
Example shown: front left zone
Power level adjustment + or - for each heating zone.
On / off touch control for each heating zone
Ø 180 mm
50 W to 2800 W
Ø 180 mm
50 W to 2800 W
Page 5
3
Turning on a heating zone
Locate the touch controls on the keypad which corresponds to the cooking zone on which you have placed your pan.
Press the touch control.
The power level display shows 0, the hob is switched on.
Set the power level required by pressing the
touch control.
Once you have pressed the touch control, if you do not select a power level, the instruction will be cancelled automatically after 10 seconds.
Adjust the power level during cooking
You can adjust the power level from 1 to 9 at any time during cooking using the
or touch controls.
Turning off a heating zone
Press the touch control of the zone concerned.
Using 2 cooking zones simultaneously
These two zones have a total of 2800 W of power available, distributed automatically between the front and rear zones.
This means that when one zone is being used at maximum, the power of the other is automatically reduced.
The most recent instruction always takes priority.
Use
For the user
Page 6
4
For the user
Safety
Check regularly that there are no objects (tea towel, paper, etc.) which might block the air inlet located below your hob (see fitting P. 12).
“Electronic” safety feature
A sensor constantly monitors the temperature of the electronic circuits. If the temperature rises too high the power supplied by the hob will be reduced.
“Empty pan” safety feature
Each heating zone is fitted with a sensor which constantly monitors its surface temperature, so no more danger of overheating caused by empty pans.
Detection of an object or a pan on a heating zone
A small object such as a fork, a spoon or even a ring left on the hob is not detected as a saucepan. The display flashes and no heating power is produced. The safety system acts in the same way when it detects a pan which is not suitable for cooking by induction.
IMPORTANT: If an oven is located under your hob (see installation options) the thermal safety devices on the hob will prevent its simultaneous use when the oven is in pyrolysis mode.
For the attention of wearers of pacemakers
and active implants:
The functioning of the hob is in conformity with current standards on electro­magnetic interference. Your induction hob also fully complies with the legal requirements (EC directives 89/336/EEC). It has been designed not to interfere with the operation of other electrical appliances as long as these comply with the same legislation.
Your induction hob generates magnetic fields in its immediate area.
So that there is no interference between your hob and a pacemaker, the latter must be designed in conformity with the relevant regulations. In this respect, we can only guarantee the conformity of our own product. Insofar as the conformity of the pacemaker or any incompatibility is concerned, you should consult its manufacturer or your doctor.
Page 7
5
For the user
Precautions for use
The ceramic surface is very strong, however, it is not unbreakable: do not drop pans onto it.
Saucepans with damaged bases may trap and transfer materials which could cause staining or scratching of the hob.
Do not drag saucepans across the hob surface as in the long term this will damage the design on the ceramic top.
These faults, which do not prevent operation or use of the hob, are not covered by the guarantee.
The hob must not be used as a storage area.
Do not store
C
LEANING
products or any products which might be
I
NFLAMMABLE
in the unit located under your hob.
When plugging electrical appliances into a socket nearby, make sure that the power cable does not come into contact with the heating zones.
If a crack appears in the ceramic top,
disconnect the appliance from
the power supply immediately by removing
the fuses or activating the circuit breaker.
Do not use any part of the hob until the ceramic top has been
replaced
Useful advice
Page 8
6
For the user
Useful advice
Advice on cooking
Do not leave an empty pan on a heating zone.
The pan should be centred on the heating zone.
Never heat up an unopened tin, it may explode; this advice applies to all cooking systems.
When you use a pan with a non-stick lining (Teflon type) to cook with no fat or very little, preheat it at setting 6 for a moment.
You are advised not to place metal cooking ustensils, cutlery, knives and similar metal objects on the hob. They may become hot if they are near a functioning cooking zone.
Using a pan which is smaller than the size of the cooking zone indicated on the ceramic top is quite acceptable and does not result in a loss of energy, unlike other, standard hobs (electricity, gas).
When cooking, never use aluminium foil
and never place products wrapped
in aluminium foil directly on the induction hob.
The aluminium will melt and damage your appliance irreparably.
Page 9
7
For the user
Choice of pans
Which types of pan are most suitable?
You probably already have some suitable pans.
PANS MADE OF ENAMELLED STEEL WITH OR WITHOUT NON-STICK COATING.
casserole, deep fryer, frying pan, grill pan, etc.
CAST IRON PANS
To prevent the ceramic top on your hob from being scratched choose a pan with an enamelled base, otherwise never slide the pan across the surface of the hob.
STAINLESS STEEL PANS DESIGNED FOR INDUCTION COOKING
Most stainless steel pans are suitable for induction cooking (casseroles, sauce­pans, frying pan, deep fryer, etc.).
ALUMINIUM PANS WITH SPECIAL BASE
Choose pans with a heavy base, which will ensure more even cooking results (the heat is better distributed).
NB. Pans which do not have a completely flat base may be suitable,
however, they must not be too misshapen.
This hob carries the “CLASS INDUCTION” symbol .
By choosing a pan bearing the same symbol, you will be assured of its complete compatibility with your hob, under normal conditions of use. To help you in your choice, a list of ustensils is supplied with this instruction book.
Which materials are incompatible?
PANS MADE OF GLASS, CERAMIC OR EARTHENWARE, OR OF ALUMINIUM WITHOUT A SPECIAL BASE OR OF COPPER,
OR OF CERTAIN TYPES OF NON-MAGNETIC STAINLESS STEEL.
The “pan” test
Its advanced technology enables your induction hob to recognise most types of pan.
Place your pan on a heating zone at power setting 3:
- if the display does not flash your pan is compatible,
- if it flashes then your pan cannot be used for induction cooking.
INDUCTION
Page 10
8
For the user
Cleaning
TYPE OF STAIN
Minor
Accumulated burnt-on
stains
Rings and traces of limescale
Burnt-on stains following
sugar spillage, melted
aluminium or plastic.
WHAT TO DO ACCESSORIES
REQUIRED
Soak the area to be cleaned thoroughly with hot water, then wipe clean
cleaning sponges
Soak the area to be cleaned thoroughly with hot water, if necessary, finish off with the rough side of a scouring sponge, then wipe
clean.
cleaning sponges
Apply hot white spirit
vinegar to the stain, leave to
act then wipe off with a soft cloth.
Or use a commercial
cleaner.
Special ceramic hob
cleaning paste
Use a special ceramic hob
scraper to loosen the resi-
due
Or apply a special
ceramic hob cleaner to the surface, preferably one which contains silicone (protective action).
Special ceramic hob
cleaner
Page 11
9
For the user
You are worried that your hob is not functioning properly...
Call your After Sales Service.
Check the connections and the mains connection are correct.
This is quite normal
The electronic circuit is dysfunctionning
Your hob has been wrongly connected.
Your hob has been wrongly connected.
This is caused by the distribution of power between two induction cooking zones.
The electronic system is being cooled.
See section choice of pans.
The pan you are using is unsuitable for cooking by induction or has a diameter less than 12 cm.
Inspect the fuses and the circuit breaker.
The appliance has no power. Either the power supply or the connection is faulty.
The hob does not work, the display indicates another message.
When you switch the appliance on, your mains cuts out.
When you switch it on, only one side of your hob functions.
Your hob makes a slight clicking noise.
The fan continues operating for a few minutes after your hob is switched off.
After having switched on a heating zone, the lights on the keypad continue to flash.
Check the connections. The supply vol­tage is too high.
Your hob has been wrongly connected.
The hob does not work, the display indicates an intermittent «Point».
The hob does not work. The lights on the keypad stay off.
The display indicates the message
F7
F7
The electronic circuits have overheated.
See section building in.
The electronic system is on standby, as with any other electronic appliance (TV, transformer).
The top of your hob is always slightly warm (even when off)
... this does not necessarily mean there is a fault.
Always check the following points first.
WHAT TO DOPOSSIBLE
CAUSES
YOU NOTICE
THAT...
NOTHING: see section
with notes on connection
Normal operation
When you switch the appliance on a display lights
See “how induction works”
This is quite normal
Page 12
10
Precautions
Please comply scrupulously with the following points:
The walls above the worktop and immediately next to the hob must be heat-resistant.
Laminated surfaces and the adhesives used to fix them must be heat-resistant to avoid
any deterioration.
The cool air gap located underneath and to the rear of the hob is there to increase its
reliability by ensuring that it remains cool in all types of fitting arrangement.
The hob must not be installed above a dishwasher, washing machine, refrigerator or
freezer.
Protecting the cut-out:
The chipboard used in the manufacture of worktops swells relatively quickly when in contact with humidity. Apply a varnish or a specialist glue to the edge of the cut-out to protect it from any steam or condensation which may originate from under the worktop.
Make a cut-out in the worktop with the dimensions required. The minimum distance
of 40 mm should be measured from the wall and any side walls (rear and/or sides).
Protection from heating is Type Y in accordance with IEC 335-2-6
Building in
Page 13
11
L2
Technical data
Operating voltage 220/240V - 50/60Hz Total power consumption 5600W
Cut-out dimensions of the furniture
Width L 560 mm Depth P 490 mm Space needed under the worktop H 63,3 mm
Overal dimensions below the worktop
Width L1 555 mm Depth P1 488 mm
Overal dimensions above the worktop
Width L2 580 mm Depth P2 510 mm
Weight approx. 14.5 kg Manufacturer N°214
P2
H
40 mm
mini
P1
L1
P
L
40 mm
mini
40 mm
mini
Page 14
12
It is essential that you install an insulation kit between the oven and the hob (available from your dealer’s After Sales Service). This arrangement restricts installation of the oven to the lower position in the unit.
,,,,,
30 cm
,,
,,
5 cm
Installation options
above an empty unit or drawer
above an oven of another brand
above an oven of the same brand
Your induction hob must always be well-ventilated. Make sure that the flow of air through the ventilation grille at the back is completely unobstructed.
4 mm
Above an empty unit or drawer
Above an oven of another brand
75X 1652
Fitting the hob :
- Unscrew the screws V on the hob air guide.
- Place your hob in the cut-out.
- Pull the air guide out until it comes into contact with the front (if this is a door or a drawer, pull the guide out more than necessary and push it back by closing the door or drawer) then replace the screws V on the guide
AIR OUTLET
V
AIR INLET
80mm
air
gap
5 mm
front of unit
Page 15
13
Building in
Your oven carries the BRANDT label, and it has an upper ventilation system and the hob can therefore be fitted directly into the worktop above the oven in the higher position.
It is essential that an air inlet of 30 cm
2
be made in the left or right wall of the oven
housing unit. Reminder: the hob’s thermal safety devices prevent its simultaneous use with an oven in pyrolysis mode.
30 cm2
Building in above an oven
Example shows air inlet through the rear right
Above an oven of the same brand
Page 16
14
Neutral
Earth
Live
N L
- 220/240 V single phase
Connect the three wires to your mains supply, in
accordance to the colour of the wires.
Remarks
When your hob is first connected to the power supply or after a long power cut, a code lights up on the keypad. It disappears automatically after about 30 seconds or the first time any of the touch controls on the keypad is pressed. This display is normal and reserved for the use, as required, of your After Sales Service. When connecting to a 400 V ~ three phase mains supply, if your hob malfunctions, check that the neutral wire has been connected properly. These precautions will also protect your other electronic appliances.
Neutral
Earth
Live 2
Live 1
N
L1
L2
NB
separate the 2 live wires L1, L2 before connecting
Blue
Blue
Green / yellow
Blue sleeve
Black
Black sleeve
- 400 V 2N three phase
Connect the four wires to your mains supply, in
accordance with the colour of the wires.
Your mains fuse must be: 32 amp
Green / yellow
Blue
Blue
Blue sleeve
Black
Black sleeve
Electrical Connection
These hobs are supplied with an 05 VVF power supply cable (cross-section 1.5 mm2), with 5 cores (of which one for the earth: yellow/green) and should be connected to the mains by a socket which complies with the EEC 7 regulations or by using a double-pole circuit breaker with a contact gap of at least 3 mm. If this power supply cable is damaged, or if you wish to change it, it can only be replaced by your After Sales Service as this requires specialist tools.
Loading...