Page 1
cooking collection
Instructions for use and warranty details
Gas Cooktops
Model No.: GCTE6010 GCTE7010 GCTE9010 and GCTE12010
Page 2
2
Your new Kleenmaid appliance has been
designed and manufactured to give you
years of reliable performance.
For best results, carefully read the
instructions on how to install your new
appliance. Correct installation will avoid
delays and unnecessary service call costs.
Once installation is complete, please read
this entire instruction manual carefully and
get to know the controls and the features
of your new Kleenmaid appliance.
Again, congratulations and thank you for
choosing Kleenmaid.
Congratulations on the purchase
of your new Kleenmaid appliance.
Page 3
3
Index
Instructions for use
Installation, 4
Use, 4
Maintenance, 7
Instructions for the installater
Installation, 8
Electrical connection, 11
THIS APPLIANCE IS CONCEIVED FOR
DOMESTIC USE ONLY.
THE MANUFACTURER SHALL NOT IN
ANY WAY BE HELD RESPONSIBLE FOR
WHATEVER INJURIES OR DAMAGES ARE
CAUSED BY INCORRECT INSTALLATION OR
BY UNSUITABLE, WRONG OR ABSURD USE.
THIS APPLIANCE IS NOT INTENDED FOR
USE BY PERSONS (INCLUDING CHILDREN)
WITH REDUCED PHYSICAL, SENSORY
OR MENTAL CAPABILITIES, OR LACK OF
EXPERIENCE AND KNOWLEDGE, UNLESS
THEY HAVE BEEN GIVEN SUPERVISION OR
INSTRUCTION CONCERNING USE OF THE
APPLIANCE BY A PERSON RESPONSIBLE
FOR THEIR SAFETY.
CHILDREN SHOULD BE SUPERVISED TO
ENSURE THAT THEY DO NOT PLAY WITH THE
APPLIANCE.
Dear customer,
We thank you and congratulate you on your
choice.
This new carefully designed product,
manufactured with the highest quality
materials, has been carefully tested to
satisfy all your cooking demands.
We would therefore request you to read
and follow these easy instructions which will
allow you to obtain excellent results right
from the start.
May we wish you all the very best with your
modern appliance!
THE MANUFACTURER
Gas connection, 11
Page 4
4
Installation
All the operations concerned with the installation
(electrical and gas connections, adaptation to type of
gas, necessary adjustments, etc.) must be carried out
by qualified technicians, in terms with the standards
in force. For specific instructions, kindly read the part
reserved for the installation technician.
Use
Standby mode (Fig. 1-2-3)
When the device is turned on, it performs a brief self-test
and calibrates the touch-pad (all displays and LEDs turn
on for several seconds). At the end, the display will be
completely off. In this mode, the device can be turned on
by simply pressing the ON/OFF key.
Turning on the Cooking Surface
To turn on the device, you must hold down the ON/
OFF key for at least 2 seconds. The device will turn on
and the burner displays will display level zero, which
corresponds to burner off.
Turning on a burner
To turn on a burner, press the relative + and - keys on the
control panel. The keys must be pressed simultaneously
and held down for at least 1 second. When the burner
turns on, the burner will be set to the average flow and
the relative display will show level 3.
Each burner whose timer has not been programmed
will automatically turn off after 4 hours of continuous
operation.
The turning on of the burner is also indicated by the
relative LED near the timer display, which will be on for
the entire time that the burner is on.
Adjusting the flame level of a burner
To increase the flow to a burner that is on, press the
+ key and to decrease the flow, press the - key. For a
continuous change in the flow level, just hold down the +
or - key and release it at the desired level. The flow level
varies from 1 to 5.
Turning off a burner
To turn aburner off, press the + and -keys simultaneously
for a brief instant.
Turning off all the burners
To turn all the burners off at the same time, briefly press
the ON/OFF key; this puts the device in standby mode.
Programming the amount of time after which the
burner turns off
A time, after which a burner turns off, can be set
independently for each burner.
To program a burner timer, press the PT key. In the
part of the control panel that shows the position of each
burner with an LED, the burner A indicator (LED-A)
lights to indicate that burner A is currently selected for
programming. Use the P+ and P- keys to select the timer
of the burner to be programmed. The selected burner is
indicated by the flashing of its light. The timer display
shows 0.00 to indicate
that the timer for the selected
burner is not active. To program the turn-off time for
the selected burner, press the PT key again; the timer
display will show 0.00. The flashing digit to the left of the
decimal point indicates hours while the digits to the right
indicate minutes. By pressing the P+ or P- keys, you can
increase, or decrease, the number of operating hours
from 0 to 9. When you hold down the P+ or P- keys, the
change of hours is continuous.
To specify the number of minutes, press PT again. The
digit to the right of the decimal point flashes. Set the
minutes the same way as the hours.
When programming the time, you can zero the current
setting at any time by pressing the P+ and P- keys
together. When a time of zero is set, the burner timer is
deactivated. To confirm the time displayed, press the PT
key. At this point, the only burner LEDs that are flashing
are those whose timers are running.
By pressing the PT key, you can return to timer
programming mode to see how much time remains
before the burner turns off or to change the current
setting. If, during programming, no key is pressed for
longer than 10 seconds, programming is automatically
interrupted and the main display returns. Any settings
that were made for the selected burner are stored and
the relative timer is running.
A timer can be set whether a burner is on or off and
the countdown starts immediately after the time setting
is confirmed. When the timer reaches zero, the timed
burner will be turned off and, at the same time, there
will be a beep.
When you turn off a burner, its timer is also deactivated.
Setting the clock
After a power failure, the time displayed by the clock
inside the device must be reset.
To set the clock, you must press the PT, P+ and P- keys
simultaneously for at least 3 seconds.
The flashing digit to the left of the decimal point indicates
hours while the digits to the right indicate minutes.
Pressing the P+ or P- keys increases or decreases the
hours and, when you hold down the P+ or P- key, the
number of hours changes continuously.
Press the PT key again to set the minutes. The digits
to the right of the decimal point will flash and you can
Instructions for use
Page 5
5
change the minutes in the same way described for the
hours.
When you press PT, the time setting will be saved.
Unlocking the burners
When a burner is locked, the relative display shows the
letter “b”. To unlock, hold down the burner A key and
the KL key for at least 2 seconds. After being unlocked,
the burners will be reset to level 0, ready to be turned
on again.
Note: If you have to repeat the unlock procedure 5
consecutive times in a period of 15 minutes, the device
will display FT06 and will not allow any more unlocks for
another 15 minutes.
Locking the keypad
This is activated by pressing just the KL key for at least 2
seconds. All the burners will remain at the current level.
The status of the keypad is indicated by the lighting of the
decimal points in the flow level displays for each burner.
When the keypad is locked, it is not possible to change
the levels of the burners or change the timer settings but
it is possible to turn off the surface by pressing the ON/
OFF key.
It is not possible to unlock a locked burner while the
keypad is locked. For this reason, you must unlock the
keypad before unlocking the burners.
Unlocking the keypad
To unlock the keypad, press the KL key and the + key
of burner A for at least 2 seconds. When the keypad is
unlocked, the decimal points in the level displays turn
off.
Residual Heat
When a burner goes out, the relative display shows an
"H" to indicate that the temperature of that burner is still
high and the relative LED near the timer display remains
on.
The "H" symbol and the LED turn off when the
temperature of the relative burner is cool.
Special slow cooking (Duty cycle)
This function turns any cook top burner on and off is the
sequence shown in the table.
LEVEL SET. 1 2 3 4 5
TURN-OFF TIME
10
Sec.20Sec.30Sec.40Sec.50Sec.
TURN-ON TIME
50
Sec.40Sec.30Sec.20Sec.10Sec.
The function is activated by pressing the + key of the
burner you want to apply it to, and the PT key (the burner
involved must be off when this function is activated).
The burner turns on at level 3 and, at that time, you can
set the level to apply the function to by pressing the +
and - keys.
If, for example, you set the value to level 1, the burner
will remain on for 50 seconds, then it will turn off for 10
seconds and repeat this cycle until you turn the burner
off.
If the user does not intervene it turns off automatically
after 60 minutes. When this function is active the display
A
of the relative burner flashes.
Warning
Do not use or store flammable materials near this appliance.
Do not spray aerosols in the vicinity of this appliance while it
is in operation.
Do not modify this appliance.
Where this appliance is installed in a marine craft, caravan
or mobile home. It shall
not be used as a space heater.
Page 6
6
Turning
ON/OFF
Lock
Time activation
The lighting of an LED means
that the function is active for
that burner.
A flashing LED indicates that
the timer of the relative burner
has been activated.
Setting
burner A
Setting
burner B
Setting
burner C
Setting
burner D
Setting
burner E
Timer
setting
Fig. 1
Fig. 2
Fig. 3
Setting
burner A
Setting
burner B
Setting
burner C
Setting
burner D
Timer
setting
Turning
ON/OFF
Lock
Time activation
Setting
burner A
Setting
burner B
Setting
burner C
Setting
burner D
Timer
setting
Turning
ON/OFF
Lock
Time activation
The lighting of an LED means that the
function is active for that burner.
A flashing LED indicates that the timer of
the relative burner has been activated.
The lighting of an LED means that the
function is active for that burner.
A flashing LED indicates that the timer of
the relative burner has been activated.
U
Mod: GCTE6010
Mod: GCTE7010
GCTE9010
Mod: GCTE12010
Page 7
7
N.B
- We recommend the use of pots and pans with a
diameter matching that of the burner, thus preventing
the flame from escaping from the bottom part and
surrounding the pot (Fig. 4);
- do not leave any empty pots or pans on the fire;
When cooking is finished, it is also a good norm to close
the main gas pipe tap and/or cylinder.
auxiliary* Ø 10-14
GAS
Fig. 4
DO NOT USE STEAM CLEANERS
Always refer servicing to an authorised service person. It
is recommended that the appliance be serviced at least
once per year to ensure the appliance continues to
www.kleenmaid-appliances.com.au
semifast Ø 14-20
fast Ø 20-26
wok Ø 20-32
perfroming as per the original installation contact Kleenmaid.
operate correctly and safety. If the appliance is not
Maintenance and Service Contact for Service and Parts
leaving
Prior to any operation, disconnect the appliance from
the electrical system. For long-life to the equipment, a
general cleaning operation must take place periodically,
bearing in mind the following:
the glass and steel parts must be cleaned with
suitable non-abrasive or corrosive products (found
on the market). Avoid chlorine-base products (bleach,
etc.);
avoid acid or alkaline substances on the
working area (vinegar, salt, lemonjuice, etc.);
the wall and the small covers (mobile parts of
the burner) must be washed frequently with boiling
water and detergent, taking care to remove every
possible encrustation. Dry carefully and check that
none of the burner holes is fully or partially clogged;
check periodically the state of conservation of the flexible
gas feed pipe. In case of leakage, call immediately the
qualified technicians for its replacement.
•
•
•
Page 8
8
Instructions for the installer
Installation
This appliance is not provided with a combustion
product discharge. It is recommended that it be installed
in sufficiently aerated places, in terms of the laws in force.
The quantity of air which is necessary for combustion
must not be below 2.0 m
3
/h for each kW of installed
power. See table of burner power.
Positioning (Fig. 5)
The cook top is designed to be built in to a work surface
as shown in the figure.
Before installing the cook top, install the gasket seal
around the entire perimeter of the hole where it will be
inserted.
The dimensions of the hole are shown in figures 6-7-8-9.
For Filotop models, the perimeter of the hole must be
lowered by a depth of 1.5 mm.
The hole does not need to be milled for Semifilotop
models.
The cook top can be installed on different materials such
as brickwork, steel, marble, conglomerates, synthetics,
wood and wood covered with plastic laminates, so long
as resistant to a temperature of 90 °C.
Fig. 5
A panel made of wood or other insulating material
must be installed under the cook top at a distance
of at least 15 mm from the surface.
Range hoods and exhaust fans shall be
installed in accordance with the
manufacturer’s relevant instructions.
However, in no case shall the clearance
between the highest part of the hob of the
gas cooking appliance and a range hood
be less than 600 mm or, for an overhead
exhaust fan, 750 mm.
Page 9
9
Fig. 6
591
+1
0
511
+1
0
560
+1
0
490
+1
0
R
1
2
1.5
590
510
R
1
1
74
1
1
3
2
2
Note: Semifilotop models do
not need to be lowered by 1.5
mm.
1 - AUXILIARY
2 - SEMI-RAPID
3 - RAPID
74
770
510
R
1
1
771
+1
0
511
+1
0
490
+1
0
750
+1
0
1.5
R
1
2
1
3 2
4
2
1 - AUXILIARY
2 - SEMI-RAPID
3 - RAPID
Note: Semifilotop models do
not need to be lowered by 1.5
mm.
Fig. 7
A
4 - Wok
Mod: GCTE6010 gas inlet is located at the rear, right corner
Mod: GCTE7010 gas inlet is located at the rear, right corner
Page 10
10
860
510
R
1
1
861
+1
0
511
+1
0
490
+1
0
840
+1
0
1.5
R
1
2
74
1
3 2
4
2
1 - AUXILIARY
2 - SEMI-RAPID
3 - RAPID
Note: Semifilotop models do
not need to be lowered by 1.5
mm.
Fig. 8
1120
R
1
1
1121
+1
0
385
+1
0
365
+1
0
1100
+1
0
1.5
R
1
2
74
384
1 34 2
1 - AUXILIARY
2 - SEMI-RAPID
3 - RAPID
Note: Semifilotop models do
not need to be lowered by 1.5
mm.
Fig. 9
U
4 - Wok
4 - Wok
Mod: GCTE9010 gas inlet is located at the rear, right corner
Mod: GCTE12010 gas inlet is located at the rear, right corner
Page 11
11
The connection to a gas tank or gas line must be made
by a qualified person in conformity to current updated
available. If not, see: “Adapting to different types of gas”.
Also check that the feed pressure falls within the values
shown in the table: “User characteristics”.
Fig. 10
Metal rigid/semi-rigid hook-ups
Make the hook-up with metal fittings and pipes (even
flexible hoses) so as not to stress the components inside
the cook top.
Note: - After installation, use soapy water to check the
perfect seal of the entire connection system.
Important note: make the connection using only metal
fittings and pipes (flexible, continuous-wall steel hoses
or rigid copper or steel tubing) and in such a way that its
Electrical connection
(Fig. 11)
The earth connection is compulsory in terms of the
law.
Should there be no cable and/or plug on the equipment,
use suitable absorption material for the working
temperature as well, as indicated on the matrix
plate. Under no circumstance must the cable reach a
temperature above 50°C of the ambient temperature.
If connecting directly to the mains power supply, fit a
multi-pole switch of a suitable size for the rated capacity
with a clearance distance which completely disconnects
the power line under overvoltage category III conditions,
consistently with the rules of installation (the yellow/
green earth wire must not be interrupted). The plug or
omnipolar switch must be easily reached on the installed
equipment.
Fig. 11
A
Gas connection (Fig. 10)
Only by an authorised person
AS 5601 (gas installations), local authority and regulations.
Check the cooktop is prepared for the type of gas supply
entire length can be inspected.
Flexible hose must be certified to AS 1869 class B or D
hose must not be kinked or be able to touch any hot
surface. The supply connection point must be accessible
10mm in diameter and no longer than 1200mm. The
when installed.
The installer must test the operation of the appliance
including gas leakage, ignition and turndown of all
burners. If the appliance cannot be adjusted to perform
correctly refer to the following
fault finding table or visit
www.kleenmaid-appliances.com.au
The installer must be qualified and is responsible for
correct electrical connections and following safety
standards.
Prior to carrying out the electrical connection, please
ensure that:
plantthe•
•
characteristics are such as to follow what is
indicated on the matrix plate placed at the bottom of
the working area;
thethat plant is
with an earth connection,
following the standards and law provisions in force.
Page 12
12
Adaptation to varius types of gas
(Fig. 12)
Wok only
Fig. 12
Procedure for adjusting the minimum burner flow
The procedure for setting minimums allows the operator to
change minimum flow setting, adapting each burner to the
characteristics of the gas distribution system to which the
cook top is hooked-up.
The procedure is activated by holding down the + and keys of burner A together with the + and - keys of burner D
for 3 seconds, with all the burners off for a 4-burner model
while, for a 5-burner model, hold down the + and - keys of
burner A together with the + and - keys of burner E.
The display indicates the activation of the procedure with
“MIN”. At this point, you can select the burner to adjust by
pressing the P+ and P- keys. After confirming with the PT
key, the selected burner will light at the minimum and you
will be able to increase or decrease the minimum flow by
pressing the + and - keys for that burner. During regulation,
the flame level display will show -, if the minimum set is the
factory setting, and will display a flashing ^ or v to indicate,
respectively, a higher or lower flow than the factory setting.
To confirm the minimum flow desired, you must press the
PT key. “MIN” will remain displayed and no LEDs will flash,
so, at this point, you can press PT to exit the procedure
or press the P+ or P- keys to select another burner and
set the minimum flow. The minimum flow levels are then
acquired and stored by the device and will be used during
normal use of the cook top.
Selecting the type of fuel gas
You can configure the cook top to work with different
gases (see table 1). To select the fuel gas to use, the
cook top must be on with all the burners off. Just press
the burner A, burner B and P- keys together for at least 2
seconds. When the fuel gas selection procedure starts,
the burner level display turns off and the timer display
shows “2020”, “3029”, “2525” or “2010”, depending on
the current configuration in use. It is possible to select
the desired setting with
the P+ and P- keys. To end the
procedure, you must press the PT key.
Using this function deletes any turn-off times that may
have been programmed for the burners.
Electronic self-test
The electronic cards are continuously checking their
status. If there are any hardware or board problems that
could affect the end-user's safety, the cook top goes
into a “safe” mode which closes the solenoid valves and
displays a code relative to failure.
Warnings for correct functioning of the flame detection
circuit built-in to the appliance.
This device can be used in neutral phase 230V electric
circuits, with neutral connected to earth.
The device must be adapted if used with electric circuits
of different types.
Should the appliance be pre-set for a different type of
gas than available, procreed as follows:
• replace the injector (Fig. ?) with the corresponding type
of gas to be used (see table “User characteristics“);
Page 13
13
Error
displayed
Problem type Possible cause Possible solution
B Single burner locked
No gas
Restore the gas and unlock the
burners
Ionization electrode dirty or not hit by the flame
Clean or reposition the
electrode and unlock the
burners
The cook top is not grounded
Check the cables and unlock
the burners
F
Parasite flame/flame detection
circuit anomaly on the single
burner
Ionization electrode wired incorrectly Check the wiring
Failure at the circuit Replace the device
Flt00
Main valve control circuit
anomaly
Failure at the circuit Replace the device
Flt01
Anomaly circuit voltage of
reference
Failure at the circuit Replace the device
Flt02 Watchdog circuit anomaly Failure at the circuit Replace the device
Flt03 Microcontroller door anomaly Failure at the circuit Replace the device
Flt04 Eeprom anomaly Failure at the circuit Replace the device
Flt05 Pilot valve circuit anomaly Failure at the circuit Replace the device
Flt06
Limit of 5 unlocks in 15
minutes exceeded
The burners have been unlocked 5 times in 15
minutes
Wait 15 minutes before
unlocking the burners
Flt08 Power supply circuit anomaly Failure at the circuit Replace the device
Flt09
Generic anomaly
Power was cut to the device when another type
of failure had occurred previously
Unlock the burners
Resonator anomaly Failure at the circuit Replace the device
Flt0A All burners locked
No gas
Restore the gas and unlock the
burners
Ionization electrodes dirty or not hit by the flame
Clean or reposition the
electrodes and unlock the
burners
The cook top is not grounded
Check the cables and unlock
the burners
Gas is leaking from one valve that caused the
unwanted lighting of a second burner while the
first was being lit.
This problem is caused by flame in the second
burner for more than 10 seconds.
Replace the defective valve
Flt0[
Communication errors in the
control logic
Failure at the circuit Replace the device
Flt0E
Error in the control of the
keypad
A mechanical deformation could have
compromised the support of the keypad by the
glass
Wait several seconds for the
keypad to recalibrate. If the
error persists, turn the power
off and on. If the error still
persists, replace the device.
Page 14
14
Page 15
Warranty and Service
Domestic Warranty – Full two year warranty
In addition to all statutory rights which you, the Purchaser, have under relevant laws in respect of this
appliance, during the first two years of ownership as the original purchaser of this Kleenmaid appliance,
Compass Capital Services trading as Kleenmaid guarantee that any fault caused by defective material
or workmanship becoming apparent will be rectified free of charge with reference to parts and labour,
provided that all service is performed during normal working hours by Kleenmaid or their designated
Agents. Where the appliance is installed outside the normal servicing area of the above, the Purchaser
must pay for the cost of transporting the appliance to and from the Agent or the Agent’s travel cost to
and from the purchaser’s home.
Commercial Warranty – One year warranty
When this appliance is installed in a commercial application, in addition to all statutory rights which
you, the Purchaser, have under relevant laws in respect of this appliance, during the first one year of
ownership as the original purchaser of this Kleenmaid appliance, Compass Capital Services trading as
Kleenmaid guarantee that any fault caused by defective material or workmanship becoming apparent
will be rectified free of charge with reference to parts and labour, provided that all service is performed
during normal working hours by Kleenmaid or their designated Agents. Where the appliance is installed
outside the normal servicing area of the above, the Purchaser must pay for the cost of transporting the
appliance to and from the Agent or the Agent’s travel cost to and from the purchaser’s home.
What these warranties do not cover
Compass Capital Services trading as Kleenmaid is not responsible for any damage or malfunction
unless caused by a defect in material or workmanship. This includes but is not limited to abuse,
misuse, improper installation and transportation damage. Compass Capital Services trading as
Kleenmaid is not responsible for consequential damages from any malfunction.
This warranty does not cover consumable items, replacement of light globes or glass breakage due
to impact. In case of fractured glass do not use your appliance.
Purchaser’s responsibility
The Purchaser must make the appliance available for servicing and shall bear any costs incurred
for any de-installation and/or re-installation required to make the appliance available for servicing.
Compass Capital Services trading as Kleenmaid is not liable for any consequential damage incurred
during de-installation or re-installation.
Warranty registration and Proof of Purchase.
Please complete warranty details below and retain together with your proof of purchase document.
When requesting service under this warranty the Purchaser agrees that Proof of Purchase of their
Kleenmaid appliance will be necessary in order to make the warranty valid. Inability to provide Proof
of Purchase even though this warranty is in place will not bind Compass Capital Services trading as
Kleenmaid to repair the appliance at no charge under this warranty and will require the Purchaser to
pay for the service costs in full.
Model Number Date of purchase
For service assistance visit
www.kleenmaid-appliances.com.au
Page 16
Other products available in the
Kleenmaid range of appliances
|
Washing machines
|
Clothes dryers
|
Dishwashers
|
Ovens
|
Cooktops
|
Steam ovens
|
Microwave ovens
|
Built in espresso
coffee machines
|
Rangehoods
|
Freestanding ranges
|
Sinks
|
Taps
Compass Capital Services Pty Limited
trading as Kleenmaid
ABN 96138214525
Level 2, Suite 3,
204 Botany Rd
Alexandria NSW 2015
E: help@kmaid.com.au
www.kleenmaid-appliances.com.au
Loading...