Kleenmaid GCT6020 User Manual

cooking collection

Instructions for use and warranty details

Gas Cooktop

Model No.: GCT6020 and GCT9020

2

Congratulations on the purchase
of your new Kleenmaid appliance.

Your new Kleenmaid appliance has been
designed and manufactured to give you
years of reliable performance.

For best results, carefully read the
instructions on how to install your new
appliance. Correct installation will avoid
delays and unnecessary service call costs.

Once installation is complete, please read
this entire instruction manual carefully and
get to know the controls and the features
of your new Kleenmaid appliance.

Again, congratulations and thank you for
choosing Kleenmaid.

3

Dear Customer,

we would like to thank you and congratulate you on
your choice.

This new product has been carefully designed and built
using top quality materials, and meticulously tested to
ensure that it meets all your culinary requirements.

Please read and observe these simple instructions,
which will enable you to achieve excellent results
from the very first time you use it. This state-of-the­art appliance comes to you with our very best wishes.

THE MANUFACTURER

THIS PRODUCT IS DESIGNED FOR DOMESTIC
USE.
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY FOR DAMAGES TO THINGS
OR PEOPLE DERIVING FROM INCORRECT
INSTALLATION OR IMPROPER, ERRONEOUS OR
UNSUITABLE USE.
THE APPLIANCE MUST NOT BE USED BY
PEOPLE (INCLUDING CHILDREN) WITH PHYSICAL,

4

SENSORIAL OR MENTAL IMPAIRMENTS, OR BY
PEOPLE WITHOUT THE NECESSARY EXPERIENCE
OR KNOWLEDGE, UNLESS THEY ARE SUPERVISED
OR INSTRUCTED IN THE USE OF THE APPLIANCE
BY A PERSON RESPONSIBLE FOR THEIR SAFETY.
CHILDREN MUST BE SUPERVISED TO ENSURE
THAT THEY DO NOT PLAY WITH THE APPLIANCE.

GENERAL NOTICE

We invite you to read this instruction booklet carefully, before installing and using the equipment.

It is very important that you keep this booklet together with the equipment for any future

If this equipment should be sold or transferred to another person, make sure that the new

user receives the booklet, so that they can learn how to operate the appliance and read the

This appliance complies with the following Directives:

EEC 2009/142/CE (Gas) EEC 2004/108/CE (Electromagnetic Compatibility)
EEC 2006/95/CE (Low Voltage) EEC 89/109 (Contact with foods)

WARNING

– The installation must be carried out by authorised personnel, in conformity with the regulations in force.
– CAUTION: The surface temperature of underbench components exceeds 95°C. To avoid a hazard,

underbench access must be restricted. Refer to the installation instructions.

– This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.
– Children should be supervised to ensure that they do not play with the appliance.
– Before powering the equipment, check that it is properly adjusted for the type of gas at disposal (see the

“installation” paragraph).

– If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
– Before carrying out the maintenance or cleaning the equipment, cut off power supply and allow it cool

down.
– Make sure that air circulates around the gas equipment. Insufficient ventilation produces a lack of oxygen.
– In case of an intense or prolonged use of the equipment, it may be necessary to improve aeration, for

example by opening a window or increasing rangehood venting power, if it exists.
– The products of combustion must be discharged outside through a suction hood or an electric fan (see

the “installation” paragraph).
– For any possible operation or modification, apply to an authorized Technical Assistance Centre and

demand original spare parts.

– WHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT OR IN CARAVANS, IT SHALL NOT BE

USED AS A SPACE HEATER.

– Not for use in marine craft, caravans or mobile homes unless each burner is fitted with a flame

safeguard.
– DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.
– DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

consultation.

corresponding notice.

This is a Class 3 appliance.

DO NOT MODIFY THIS APPLIANCE.

Servicing shall be carried out only by authorised personnel.
The product label, with the serial number, is fixed to the underside of hob.

An additional label should be adhered to adjacent cabinetry for easy access- refer installation
instructions.

The manufacturer refuses all responsibility for possible damages to things or people, resulting
from incorrect installation or from an improper, incorrect or unreasonable use of this equipment.

1

INSTRUCTIONS FOR THE USER

It is necessary that all the operations regarding the installation, adjustment and
adaptation to the type of gas available are carried out by authorised personnel, in
conformity with the regulations in force. The specific instructions are described in the
booklet section intended for the installer.

Conditions of Use.
This appliance is intended to be used in household and similar applications such as:

- Staff kitchen areas in shops, ofces and other working environments

- Farm Houses

- By clients in hotels, motels and other residential type environments

- Bed and breakfast type environment

USING THE BURNERS

The symbols silk-screen printed on the side of the knob
indicate the correspondence between the knob and the
burner.

Automatic start-up with valves

Press and hold the control knob down whilst turning it
anticlockwise to the maximum position (large flame, fig.1).
Once the burner is alight, continue to hold the knob down
for about 6 seconds.

ATTENTION: the triple ring burner switches on only in
the maximum flame position

Using the burners

In order to obtain the maximum yield without waste of
gas, it is important that the diameter of the pot is suitable
for the burner potential (see the following table), so as to
avoid that the flame going out (fig. 2).
Use the maximum capacity to quickly make liquids reach
boiling temperature, and the reduced capacity to heat
food or maintain boiling. All of the operating positions
must be chosen between the maximum and the minimum
ones, never between the minimum position and the
closing point.
The gas supply can be interrupted by turning the knob
clockwise up to the closing position. If there is no power
supply, it is possible to light the burners with matches,
setting the knob to the start-up point (large flame, fig. 1).

Power (MJ/h) Ø of

BURNERS

Auxiliary 3,2 3,4 10 - 14 cm

Semi-rapid 6,0 5,6 16 - 18 cm

Rapid 11,2 9,6 20 - 22 cm

Triple crown 10,8 10,4 24 - 26 cm

Double crown 10,3 9,6 20 - 22 cm

NG ULPG

cookware

(*)

It is important to use cookware with the sizes
specified and ensure the cookware is always
correctly centred over the burner. Using
oversize cookware can potentially cause heat
damage to your benchtop and/or control knobs
which will not be covered under warranty.

Notice

– When the equipment is not working, always check that

the knobs are in the closing position (see fig.1).

– If the flame should blow out accidentally, the safety

valve will automatically stop the gas supply, after a
few seconds. To restore operation, set the knob to the
lighting point (large flame, fig. 1) and press.

– While cooking with fat or oil, pay the utmost attention as

these substances can catch fire when overheated.

– Do not place unstable or deformed pots on the burner,

so as to prevent them from overturning or overflowing.

– Handles should be turned away from the front of the

bench to avoid accidents.

– When the burner is started up, check that the flame is

regular and, before taking pots away, always lower the
flame or put it out.

(*) For cookware with diameter 120mm or
below use mini-trivet supplied, refer
fitment

instructions on page 12.

2

INSTRUCTIONS FOR THE USER

1 Burner
2 Flame safeguard sensor (where fitted)
3 Injector
4 Ignition spark plug

If you have a problem with the cooktop, check the table below. You may be able to solve the problem and
this will save you from paying for a service call. You will have to pay for a service call even in the warranty
period if the problem is one listed below

FAULT POSSIBLE CAUSES REMEDY

Burner will not light

even though the

sparker is working.

No spark is obtained

when control knob is

activated

Flames uneven or

tending to lift

Flames not staying on

when knob released

Low heat, slow

cooking

Benchtop or knobs

overheating

If the above points have been checked and there is still a problem with the

Centre.

Service

Abnnormal Operation

Any of the following are considered to be abnormal operation and may require servicing:
Yellow tipping of the hob burner flame; Burner extinguished by cupboard doors; Gas valve, which are
difficult to turn;Sooting up of cooking utensil; Burner not igniting propely; burner failing to remain
alight;In case the appliance fails to operate correctly, contact the authorised service provider in your

area.

Knob not held down long enough in
‘High’ position for flame safeguard
(where fitted) to engage

Gas supply valve turned off Turn on gas supply to appliance

Wrong knob turned Ensure the knob you are turning

Port blockage in ignition area Ensure that ports in ignition area are clean

Ignition spark plugs wet or dirty Dry or clean ignition spark plugs

Electricity supply is disconnected or
switched off"

Ignition spark plugs wet or dirty Dry or clean ignition spark plugs

Flame ports blocked or wet Clean or dry flame ports

Burner incorrectly fitted Ensure this component is fitted correctly

Knob not held down long enough
in ‘High’ position for flame safeguard
(where fitted) to engage

Knob not set between ‘High’ and
‘Low’

Dirt or spillage on flame safeguard
sensor (where fitted)

Incorrect cooking pot or pan being
used

Incorrect cooking pot or pan used Check table on page 3 for correct pot or

Pot or pan not located on burner
properly

Repeat lighting procedure and hold knob
down for 6 seconds in ‘High’ position (refer
page 3)

corresponds to the burner you want to light

and dry

Switch on electricity or check fuses

Repeat lighting procedure and hold knob
down for 6 seconds in ‘High’ position
(refer page 3)

Knob MUST be set between these
positions

Clean flame safe guard sensor tip

Refer to table page 3

pan to be used

Ensure pot or pan is centrally located
on burner

cooktop, please call the

3

INSTRUCTIONS FOR THE USER

CLEANING

Before any operation, disconnect the appliance from
the electrical supply.
Don’t use a steam cleaner for the cleaning the hob.

It is advisable to clean the appliance when it is cold.

Enamelled parts

The enamelled parts must be washed with a sponge and
soapy water or with a light detergent.
Do not use abrasive or corrosive products.
Do not leave substances, such as lemon or tomato juice,
salt water, vinegar, coffee and milk on the enamelled
surfaces for a long time.

Stainless steel parts

Stainless steel can be stained if it remains in contact with
highly alkaline water or aggressive detergents for
an extended period of time.
All grades of stainless steel may stain, discolour or
attain an adhering layer of
To achieve optimum surface appearance stainless steel
must be kept clean regularly using the following cleaning
procedures, this ensuring goog performance and
long service life

grime in normal operation.

INSTRUCTIONS FOR THE INSTALLER

Wash with warm soapy water and rinse with clean water.
Where the stainless steel has become extremely dirty
with signs of surface discolouration (due to periods of
neglect or misuse) use a stainless steel cleaner
DO NOT use abrasive scourers or steel wool. When
removing these stains be sure to follow the polish of
brushing lines.

Burners and racks

These parts can be removed to make cleaning easier.
The burners must be washed with a sponge and soapy
water or with a light detergent, wiped well and placed in

their housing perfectly. Make sure that the ame-dividing

ducts are not clogged. Check that the feeler of the safety
valve and the start-up electrode are always cleaned, so
as to ensure optimum operation.
The racks can be washed in the dishwasher.

Gas taps

The possible lubrication of the taps must be carried out by
authorised personnel, exclusively.

In case of hardening or malfunctions in the gas taps,
apply to the Customer Service.

The operations indicated below must be followed by authorised personnel exclusively, in

Important notice:

conformity with the regulations in force.

The manufacturing firm refuses all responsibility for damages to people, animals or things,

resulting from the failure to comply with such provisions.

This appliance shall be installed only by authorised persons and in accordance with the

manufacturer’s installation instructions, local gas fitting regulations, municipal building codes,

electrical wiring regulations, and any other statutory regulations. For Australia and New Zealand

this appliance must be installed by an authorised person in compliance with AS/NZS 5601For

outside of Australia/New Zealand refer to the relevant installation code for gas appliances in

your country.

INSTALLATION

The installation kit contains the following:

– 1 natural gas regulator
– 1 elbow
– 1 manifold
– 2 fibre sealing washers
– 4 brackets for assembly
– 4 bracket screws
– 1 pack of cooktop to benchtop seals
– 1 duplicate rating label

– For conversion to LPG
– 1 Universal LPG sticker
– 4 or 5 injectors
Additional accessory for cooking with vessels
diameter 120mm or below
– 1 mini trivet

– LPG Test Point Assembly

Installing the top

The appliance is designed to be embedded into heat­resistant benchtop capable of withstanding 85°C.

4

INSTRUCTIONS FOR THE INSTALLER

Adjacent walls, cupboards and protection for
combustible materials.

Ensure that the appliance is installed in
accordance with of AS/NZS 5601 with regard to
clearances to combustible surfaces and
materials, and
exhaust fans.
Clearance of 200mm from the periphery of burners
to vertical combustible surfaces is required.
Clearances to combustible surfaces may be
reduced only if combustible surfaces are protected
in accordance with AS/NZS 5601

The equipment must not be installed near
inflammable materials, such as curtains,
cloths,etc. Make a cut out in the benchtop, with
the dimensions indicated in fig.3, at a distance of
at least 50 mm from the appliance border to the
adjacent walls.

MODEL L (mm) P (mm) D (mm)

GCT6020

GCT9020

Any possible wall unit over the cook-top must be
placed at a distance of at least 760 mm from the
top.

IMPORTANT:

A separation panel at least 10mm from the
bottom of the cooktop must be included during
installation to prevent access to the underside
of the appliance. This panel can be made of any
non-combustible rigid material. Refer (fig. 4).
If the hob is going to be installed on the top of an
oven, precautions must be taken to guarantee an
installation in accordance with current accident
prevention standards. Pay particular attention to
the position of the electric cable and gas pipe: they
must not touch any hot parts of the oven.
Moreover, if the hob is going to be installed on
the top of a built in oven without forced cooling
ventilation, proper air vents must be installed to
guarantee an adequate ventilation, with the lower
air entering with a cross section of at least 200cm
and the higher air exiting with a cross section of at
least 60 cm2.

Fastening the top

Every cook-top is equipped with a special washer.
A set of hooks is also supplied for mounting the
cook-top.

clearances to rangehoods and

560 480 55

860

480 55

2

,

Depending on the type of mounting surface, the
suitable type of mounting hook is supplied (hook A
or hook B).
For the installation proceed as follows:

– Remove all loose components from the top.
– Turn the appliance upside down lay it's edges on

foam packaging blocks to prevent damage to the
ignition spark plugs and lay the seal S along the
external border (fig. 5).

– Introduce and place the cook-top in the hole

made in the piece of furniture, then fasten it
with the screws and fastening brackets supplied
(fig.6).

WARNING: Failure to fix the cooktop to the bench
could result in loosening of the gas connection
through movement of the cooktop and a gas leak
may result.
A duplicate rating label is included with these
instructions. Ensure this is attached to a readily
accessible surface, so that the cooktop can be

easily identied in the case of a service call.

INSTALLATION ROOM

This appliance is not provided with a device for
exhausting the products of combustion.
Therefore, it is necessary to discharge these
outside.
The room where this appliance is installed
must have a natural air inflow, so as to ensure
a regular gas combustion and room ventilation:
the necessary air volume must not be lower than

3

20m

.
Air must come from permanent openings made on
the room walls that communicate with the outside.
The section of these openings shall correspond to
at least 200 cm2.

OPERATION ON NATURAL GAS

Regulator

An appliance regulator is provided. The regulator
must be positioned so that the pressure test nipple
is accessible when the appliance is installed.
Connect the gas supply to the 1/2" B.S.P. internal
thread inlet of the regulator. Refer to page 8 for
connection point position.
Regulators are supplied pre-adjusted and
configured by the component maker for use with
Natural Gas. The appliance installer is not required
to make an adjustment to obtain the correct outlet
pressure setting.
An arrow on the base of the regulator indicates
the direction of gas flow when the inlet and outlet
of the regulator is orientated correctly. When the
regulator has been fitted check for leaks from the
connections with soapy water.

5

INSTRUCTIONS FOR THE INSTALLER

Gas Connection

This appliance is supplied for use with Natural
Gas. However, it can be converted for use
with LPG. Refer to LP conversion chapter.

There are two ways to carry out the connection to
themain gas line :

A.the hotplate can be connected with rigid pipe as
specified in AS5601 table 3.1.

B.The hotplate can be connected with a flexibe
hose, which complies with AS/NZS 1869
(Australian
more than 1,2 mm long and in accordance with
AS5601. Ensure that the hose does not contact
the hot surface of the hotplate, oven, dishwasher
or other appliance that may be installed
underneath or next to the hotplate. WARNING:
Ensure that the hose assembly is restrainned from
accidental contact with the flue or flue outlet of an
underbench oven. The hose should not be
subjected to abrasion, kinking or permanent
deformation and should be able to be inspected
along itsentire lenght. Union compatible with the
hosefitting must be use and connection testedfor
gas leaks. The supplyconnection point shall be
accessible with the appliance installed.

Supply pipe sizing

The total hourly gas consumption for the appliance
is shown on the data label. The required supply
pressure (i.e. at inlet to appliance regulator) for
each gas type is shown on the data label, and
given in page "TECHNICAL CHARACTERISTIC
TABLES". Use this information in conjunction with
the length of run, number of elbows, tees and
bends, the available s
supply requirements of other installed appliances
to determine a suitable pipe size. For assistance
in this matter refer to the appropriate section of the
Installation Code AS5601.

An Australian certified class B or D flexible
connection may be used to connect the
accordance with the AS5601 and in particular
section 4.8. Where a hose assembly is used
and
hose assembly shall be suitable for connection
to a fixed consumer piping outlet located at a
point 800 - 850mm above the floor and in the
region outside the width of the appliance to a
distance of 250mm. The point of connection to
consumer piping must be accessible with
appliance installed.

Approved), 10mm ID, class B or D, no

ervice pressure and the

cooktop in

the cooktop is in the installed position, the

Elbow positioning

It is possible to reposition the elbow if required by
loosening the locking nut and elbow by using two
spanners. Re-tighten the entire assembly after the
elbow has been repositioned. When fitting elbow to
appliance, ensure that the sealing washer is fitted.

Regulator

An appliance regulator is provided. The regulator
must be positioned so that the pressure test nipple is
accessible when the appliance is installed. Connect
the gas supply to the ½” B.S.P. internal thread inlet
of the regulator. Refer page 10 for connection point
position.

Assembly of Regulator

The assembly of the regulator to the cooktop
manifold is achieved via the elbow union and
sealing washersupplied.
The ½” parallel thread connects to the manifold, and
the sealing washer is placed between the manifold
end and the flat face on the elbow.
The ½” tapered thread connects to the outlet of the
regulator, and is sealed on the thread using
approved thread sealing tape or approved thread

sealing compound.
The inlet of the regulator is a ½” B.S.P. thread and is
connected
Regulators are supplied pre-adjusted and
configured by the component maker for use with
Natural Gas.
The appliance installer is not required to make an
adjustment to obtain the correct outlet pressure
setting.
An arrow on the base of the regulator indicates the
direction of gas flow when the inlet and outlet of the
regulator is orientated correctly. When the regulator
has been fitted check for leaks from the connections
with soapy water.

Checking the gas supply

1.

2. Connect the manometer to the cooktop

3. Turn on the gas supply and electricity and try

4. With the appliance operating check the outlet

• when all burners of the appliance are

• when the smallest burner of the appliance is

to consumer piping or hose assembly.

Check the manometer zero point is correct.

pressure point. This is located on the
regulator.

to ignite the gas. NOTE! lt will take additional
time to light the gas for the first time as air
needs to be purged from the pipes.

pressure

operating at maximum,

operating at minimum.

6

INSTRUCTIONS FOR THE INSTALLER

Under these conditions the outlet pressure should
not vary from the nominal outlet pressure of

1.00kPa by more than ± 0.20kPa

If the regulator appears to not perform
satisfactorily, then check the following points:

1. If the outlet pressure is consistently too low
then the inlet pressure may be too low and
adjustment of an upstream regulator may be
needed, or an upstream regulator or valve
with insufficient flow capacity may be present
in the gas supply line. If this is suspected then
it may be necessary to repeat fhe checks
whilst measuring both the inlet and outlet
pressure to determine if the inlet pressure is
in the range 1.13 - 5kPa.

2. Check that the regulafor has been fitted to the
gas supply line in the correct orientation, the
arrow on the base of the body indicates the
direction of gas flow.

Once these checks have been completed, if the
regulator still fails to perform in a satisfactory
manner it should be replaced.

Electrical connection

The appliance is supplied with a standard 10
Amp service cord terminated by a 3-pin plug for

connection to a standard household socket. The
electrical supply is required to power the electronic
ignition system.
NOTE: It will be necessary for servicing purposes
to disconnect the electrical power supply. The
power point should therefore be accessible after
the appliance is
installed, as specified in the local wiring
regulations.

TESTING APPLIANCE OPERATION

After installation the installer must fully test the
appliance and ensure it operates
handing it over to the customer.

Before Leaving

Check all conection for gas leak with soap and
water. DO NOT use a naked flame for detecting
leaks. Ignite all burner both individually and
concurrently to ensure correct operation of gas
valve, burner ignition. turn gas taps to low flame
position and observe stability if the flame for each
burner individually and concurrently.
When satisfied with the hotplate, please instruct
the user on the correct method of operation. In
case the appliance fails to opperate corectly after
all checks have been carried out, refer to the
outhorised service provider in your area.

correctly before

GAS CONVERSIONS AND ADJUSTMENTS

Data Label

This appliance is suitable for Natural Gas and
Universal LPG; ensure that the available gas supply
matches the Data Label.
When converting from Natural Gas to Universal
LPG ensure that the NG
and replaced with the Test Point Assembly. An
AGA Approved gas regulator suitable for a supply
pressure of 2.75kPa should be part of the gas
tank supply and the test point pressure should be
adjusted to 2.75kPa.

Replacing the injectors

If the equipment is adjusted for a type of gas that is
different from the one available, it is necessary to
replace the burner injectors.
The choice of the injectors to replace must be
made according to the table of the “technical
characteristics” as enclosed.
Act as follows:
– remove the racks and burners.
– by means of a straight spanner L, unscrew

the injectors U (fig. 7) and substitute it with the
corresponding one.

– tighten the injectors strongly.

After changing the injectors, it is necessary to
eliminate residual natural gas in the system.
To do this you have to turn to the maximum
position then press the knob of each burner and
wait few seconds.

Adjusting the burners

The lowest flame point must always be properly
adjusted and the flame must remain on even if
there is an abrupt shift from the maximum to the
minimum position.
If this is not so, it is necessary to adjust the lowest
flame point as follows:
– start the burner up
– turn the tap up to the minimum position (small

flame)
– remove the knob from the tap rod
– introduce a flat-tip screwdriver in the hole F of the

tap (fig. 8) and turn the by-pass screw up to a

proper adjustment of the lowest flame point.

As regards U-LPG gas burners, the by-pass
screw must be tightened completely.

regulator is removed

7

INSTRUCTIONS FOR THE INSTALLER

MAINTENANCE

Maintenance Schedule

No regular maintenance is required for the
hotplates except cleaning.

The appliance should be checked by an
authorised person every 7 years to ensure the
safe operation of the appliance. This is not
covered by warranty.

Replacing the power supply cable

If the power supply cable should be replaced,
it is necessary to use a cable with a section of
3x0.75mm2, type H05VV-F or H05RR-F, complying
with the regulations in force.
The connection to the terminal board must be
effected as shown in fig.9 - 9/A:

brown cable L
blue cable N
green-yellow cable (ground)

(phase)
(neutral)

8

MAXIMUM

OFF

MINIMUM

1 2

3 4

5 6

F

9

9

9/A

87

100

MODEL: GCT6020

Depth of cooktop casing
from benchtop surface : 55mm

The gas Connection is male 1/2" BSP and is
situated at the left hand rear of the appliance ,
100 mm from the side and 50 mm from the rear
of the cooktop.

MODEL: GCT9020

Depth of cooktop casing
from benchtop surface : 55mm

The gas Connection is male 1/2" BSP and is
situated at the left hand rear of the appliance ,
300 mm from the side and 50 mm from the
rear of the cooktop.

1 Rapid burner 11,2 MJ/h 9.6 MJ/h
2 Semi-rapid burner 6.0 MJ/h 5.6 MJ/h
3 Auxiliary burner 3.2 MJ/h 3.4 MJ/h
4 Triple ring burner 10,8 MJ/h
5 Double ring burner 10.3 MJ/h 9.6 MJ/h
8 Control knob for burner

NG Universal LPG

10,4 MJ/h

10

TECHNICAL CHARACTERISTIC TABLES

BURNERS

GAS

NORMAL

PRESSURE

INJECTOR

DIAMETER

TAPE BY

PASS

DIAMETER*

N° DESCRIPTION KPa 1/100 mm 1/100 mm

1 RAPID

2 SEMI-RAPID

3 AUXILIARY

TRIPLE

4

CROWN

DOUBLE

5

CROWN

Universal LPG 2.75 85

Natural 1.00

152 3/8 11.2

Universal LPG 2.75 65 31 5.6

Natural 1.00 110

Universal LPG 2.75 52 27 3.4

Natural 1.00 80

Universal LPG 2.75

Natural 1.00

90

150 1 1/2 10.8

Universal LPG 2.75 85 60 9.6

Natural 1.00 145

42

3/8 6.0

3/8

60

7/8

*TAPE BY PASS DIAMETER: ULPG - 1/100 mm

NG - Turns from fully in.

WIRING DIAGRAM

MODEL: GCT6020

IGNITION

GENERATOR

TRIPOLAR
TERMINAL

MODEL: GCT9020

IGNITION

GENERATOR

NOMINAL

HEAT INPUT

(MJ/h)

10.4

10.3

TRIPOLAR
TERMINAL

9.6

3.2

MICRO-UNIT

MICRO-UNIT

11

INSTRUCTIONS FOR USING THE MINI TRIVET

The mini-trivet included with this cooktop is to be
used for cooking vessels of diameter 120mm or
smaller

Incorrect fitment Correct fitment

12

Warranty and Service

Domestic Warranty – Full two year warranty

In addition to all statutory rights which you, the Purchaser, have under relevant laws in respect of this
appliance, during the first two years of ownership as the original purchaser of this Kleenmaid appliance,
Compass Capital Services trading as Kleenmaid guarantee that any fault caused by defective material
or workmanship becoming apparent will be rectified free of charge with reference to parts and labour,
provided that all service is performed during normal working hours by Kleenmaid or their designated
Agents. Where the appliance is installed outside the normal servicing area of the above, the Purchaser
must pay for the cost of transporting the appliance to and from the Agent or the Agent’s travel cost to
and from the purchaser’s home.

Commercial Warranty – One year warranty

When this appliance is installed in a commercial application, in addition to all statutory rights which
you, the Purchaser, have under relevant laws in respect of this appliance, during the first one year of
ownership as the original purchaser of this Kleenmaid appliance, Compass Capital Services trading as
Kleenmaid guarantee that any fault caused by defective material or workmanship becoming apparent
will be rectified free of charge with reference to parts and labour, provided that all service is performed
during normal working hours by Kleenmaid or their designated Agents. Where the appliance is installed
outside the normal servicing area of the above, the Purchaser must pay for the cost of transporting the
appliance to and from the Agent or the Agent’s travel cost to and from the purchaser’s home.

What these warranties do not cover

Compass Capital Services trading as Kleenmaid is not responsible for any damage or malfunction
unless caused by a defect in material or workmanship. This includes but is not limited to abuse,
misuse, improper installation and transportation damage. Compass Capital Services trading as
Kleenmaid is not responsible for consequential damages from any malfunction.

This warranty does not cover consumable items, replacement of light globes or glass breakage due
to impact. In case of fractured glass do not use your appliance.

Purchaser’s responsibility

The Purchaser must make the appliance available for servicing and shall bear any costs incurred
for any de-installation and/or re-installation required to make the appliance available for servicing.
Compass Capital Services trading as Kleenmaid is not liable for any consequential damage incurred
during de-installation or re-installation.

Warranty registration and Proof of Purchase.

Please complete warranty details below and retain together with your proof of purchase document.

When requesting service under this warranty the Purchaser agrees that Proof of Purchase of their
Kleenmaid appliance will be necessary in order to make the warranty valid. Inability to provide Proof
of Purchase even though this warranty is in place will not bind Compass Capital Services trading as
Kleenmaid to repair the appliance at no charge under this warranty and will require the Purchaser to
pay for the service costs in full.

Model Number Date of purchase

For service assistance visit

www.kleenmaidhelp.com.au

Other products available in the
Kleenmaid range of appliances

|

Washing machines

|

Clothes dryers

|

Dishwashers

|

Ovens

|

Cooktops

|

Steam ovens

|

Microwave ovens

|

Built in espresso
coffee machines

|

Rangehoods

|

Freestanding oven

Compass Capital Services Pty Limited
trading as Kleenmaid
ABN 96138214525

Level 2,
204 Botany Rd
Alexandria NSW 2015

E: [e-mail]

www.kleenmaid-appliances.com.au