Kleenmaid G10FF-6SS, G9F-6SS, G12FF-8SS, G7F-4SS Instructions For Use And Warranty Details

Download

Page 1

Instructions for Use

and Warranty Details

Professional Series

Freestanding Ovens and Cooktops

Cooking

Collection

Page 2

the best you can own.

Congratulations on the purchase of your new Kleenmaid professional series appliance. This appliance has been designed and manufactured to give you years of reliable performance.

the kleenmaid story.

More than one million Australians enjoy using Kleenmaid appliances daily. Selected because of their unique design, outstanding performance, excellent quality and unquestionable reliability, each one is value-for-money, 100 per-cent guaranteed and at the top of its class.

attention to detail.

We are proud of our reputation for product innovation and service excellence. By dealing direct, we can ensure that you consistently receive a high standard of customer service.

Free delivery, dedicated customer service and after-sales service team plus free kitchen design and planning seminars are just a few of the ways we are setting new benchmarks for customer service and experience.

satisfaction guaranteed.

Your new professional series appliance is covered by a written five-year parts and labour warranty, no lemon guarantee, and a unique best value guarantee.

best results.

For best results, carefully read the enclosed instructions on how to install your new appliance. Correct installation will avoid delays and unnecessary service calls.

This booklet provides you with comprehensive information to help you get to know the controls and the features of your new appliance.

congratulations

Page 3

Contents

1. General information ______________________________________ 5

1.1 Technical service _________________________________________________________ 5

2. Warnings for safety and use ________________________________ 6

3. Installation______________________________________________ 8

3.1 General warnings _________________________________________________________ 8

3.2 Fitting the adjustable feet ___________________________________________________ 9

3.3 Fitting the front moulding ___________________________________________________ 9

3.4 Electric connection _______________________________________________________ 10

3.5 Power consumption of the vitroceramic hob____________________________________ 12

3.6 Power consumption of the volcanic rock grill ___________________________________ 12

3.7 Ventilation in rooms with gas appliances ______________________________________ 13

3.8 Gas connection__________________________________________________________ 13

3.9 Gas adjustments_________________________________________________________ 15

3.10 Connecting to LPG _______________________________________________________ 15

4. Final operations ________________________________________ 16

4.1 Levelling the cooker to the floor _____________________________________________ 16

5. Description of controls ___________________________________ 17

5.1 The front panel __________________________________________________________ 17

6. Using the cooking hob ___________________________________ 23

6.1 Switching on the burners __________________________________________________ 23

6.2 Switching off the burners __________________________________________________ 23

6.3 Abnormal Operation ______________________________________________________ 23

7. Using the deep fryer _____________________________________ 24

7.1 Before switching on the deep fryer ___________________________________________ 24

7.2 How to fry ______________________________________________________________ 24

7.3 Indicative frying times _____________________________________________________ 25

7.4 Switching off ____________________________________________________________ 25

8. Using the fry-top / steak grill _______________________________ 26

8.1 Before switching on the fry-top / steak grill _____________________________________ 26

8.2 Switching on ____________________________________________________________ 26

8.3 Energy regulator table ____________________________________________________ 26

8.4 Switching off ____________________________________________________________ 26

9. Using the volcanic rock grill _______________________________ 27

9.1 Before switching on the grill ________________________________________________ 27

9.2 Switching on ____________________________________________________________ 27

9.3 Energy regulator table ____________________________________________________ 28

9.4 Switching off ____________________________________________________________ 28

10. Using the vitroceramic hob _______________________________ 29

10.1 General warnings ________________________________________________________ 29

10.2 Switching on ____________________________________________________________ 29

10.3 Switching off ____________________________________________________________ 29

Page 4

Contents

11. Using the ovens _______________________________________ 30

11.1 General warnings ________________________________________________________ 30

11.2 Drawer ________________________________________________________________ 30

11.3 Using the electric multifunction oven _________________________________________ 30

11.4 Using the auxiliary oven with natural convection ________________________________ 32

11.5 Using the convection electric oven ___________________________________________ 33

11.6 Using the grill oven with natural convection ____________________________________ 34

12. Cooking suggestions____________________________________ 35

12.1 Suggestions for using the hob burners correctly ________________________________ 35

12.2 Suggestions for using the deep fryer correctly __________________________________ 35

12.3 Suggestions for using the fry-top / steak grill correctly ____________________________ 35

12.4 Suggestions for using the volcanic rock grill correctly ____________________________ 35

12.5 Suggestions for using the vitroceramic hob correctly _____________________________ 36

12.6 Suggestions for using the oven correctly ______________________________________ 36

13. Cleaning and maintenance _______________________________ 39

13.1 Cleaning stainless steel surfaces ____________________________________________ 39

13.2 Cleaning enamelled surfaces _______________________________________________ 39

13.3 Cleaning the polished surfaces _____________________________________________ 39

13.4 Cleaning the knobs and the control panel _____________________________________ 39

13.5 Cleaning the grids and burners _____________________________________________ 39

13.6 Cleaning the igniter plugs and thermocouples __________________________________ 40

13.7 Cleaning the deep fryer ___________________________________________________ 40

13.8 Cleaning the fry-top / steak grill _____________________________________________ 40

13.9 Cleaning the volcanic rock grill ______________________________________________ 41

13.10 Cleaning the vitroceramic hob ______________________________________________ 41

13.11 Cleaning the oven________________________________________________________ 42

13.12 Replacing the oven light bulb _______________________________________________ 42

14. Special maintenance____________________________________ 43

14.1 Removing the oven door __________________________________________________ 43

14.2 Removing the side rack-holder frames________________________________________ 44

14.3 Removing and cleaning the inside oven fan____________________________________ 44

14.4 Adjustment of the drawer height_____________________________________________ 44

Page 5

Warnings

This user’s manual is an integral part of the product purchased. The user must conserve the manual correctly so that it is always available for consultation during the use and maintenance of the product. Keep this user’s manual for future reference. If the product is resold, the manual must be transferred to any subsequent owner or user of the product.

The manufacturer is not liable for any inaccuracies in this booklet resulting from printing or transcription errors. The manufacturer reserves the right to modify its products as it considers necessary or in the interests of the user, without compromising their essential safety and operating characteristics.

CLASSES OF APPLIANCES

The cooking appliances described in this operating manual belong to the following installation classes:

• Class 1: non-flush-mounted cooking appliance;

• Class 2 – subclass 1: cooking appliance flush-mounted between two

units, made up of a single unit, but which can also be installed so that the side walls are accessible.

1. General information

1.1 Technical service

Before leaving the factory, this appliance has been tested and set up by qualified, specialist personnel, so as to guarantee the best operating results. Each repair or adjustment that may subsequently be necessary must be carried out with the utmost care and attention. We therefore recommend always contacting the Dealer where the appliance was purchased or your nearest Service Centre, specifying the type of problem and the appliance model.

Page 6

Warnings

2. Warnings for safety and use

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. IT SHOULD BE KEPT IN GOOD CONDITION AND CLOSE TO THE APPLIANCE FOR THE WHOLE LIFECYCLE OF THE COOKER. WE RECOMMEND READING THIS MANUAL AND ALL THE INDICATIONS IT INCLUDES VERY CAREFULLY BEFORE USING THE COOKER. IN CASE AN ADDITIONAL JETS KIT IS GIVEN AS ACCESSORY TO THE COOKER, WE RECOMMEND KEEPING AND PRESERVING IT. THE INSTALLATION MUST BE CARRIED OUT BY AUTHORISED PERSON

AND IN COMPLIANCE

WITH CURRENT REGULATIONS IN FORCE. THIS APPLIANCE IS ENVISAGED FOR DOMESTIC USE AND CONFORMS TO THE AUSTRALIAN STANDARDS CURRENTLY IN FORCE. THE APPLIANCE IS BUILT FOR CARRYING OUT THE FOLLOWING FUNCTION: COOKING AND HEATING FOOD; ANY OTHER USE IS TO BE CONSIDERED IMPROPER. THE MANUFACTURER DECLINES ANY RESPONSIBILITY SHOULD THE APPLIANCE BE USED FOR PURPOSES OTHER THAN THOSE INDICATED.

AT THE MOMENT OF PURCHASE, THE USER ASSUMES DIRECT RESPONSIBILITY FOR THE PRODUCT AND MUST THEREFORE MAKE SURE THAT, WITH NORMAL USE, NO INSTABILITY, DEFORMATION, BREAKAGE OR WEAR OCCURS OVER TIME THAT WOULD REDUCE PRODUCT SAFETY.

THIS PRODUCT IS DESIGNED AND MANUFACTURED TO OPERATE SAFELY AND DOES NOT POSE ANY DANGERS TO PEOPLE, ANIMALS, AND OBJECTS.

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

WHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT OR IN CARAVANS, IT SHALL NOT BE USED AS A SPACE HEATER.

DO NOT LEAVE ANY PIECES OF THE PACKING UNATTENDED IN THE HOME. SEPARATE THE VARIOUS PACKING MATERIALS AND DELIVER THEM TO THE NEAREST RECYCLING CENTRE.

THE EARTH CONNECTION IS OBLIGATORY CONFORMING TO THE MODALITIES ENVISAGED BY THE SAFETY STANDARDS OF THE ELECTRICAL WIRING SYSTEM.

THE PLUG TO BE CONNECTED TO THE POWER SUPPLY CABLE AND THE RELATIVE SOCKET MUST BE THE SAME TYPE AND MUST COMPLY WITH CURRENT STANDARDS. AFTER INSTALLING THE APPLIANCE MAKE SURE THAT THE PLUG IS ACCESSIBLE TO ALLOW THE PERIODICAL CHECK-UP.

DO NOT PULL OUT THE PLUG BY PULLING THE CABLE.

SHOULD THE GAS TAPS BE DIFFICULT TO ROTATE, LUBRICATE THEM USING A SPECIFIC PRODUCT FOR HIGH TEMPERATURES. CONTACT THE TECHNICAL SERVICE FOR THIS OPERATION.

IMMEDIATELY AFTER INSTALLATION, TEST THE APPLIANCE BRIEFLY BY FOLLOWING THE INSTRUCTIONS SHOWN BELOW. IN THE EVENT OF A MALFUNCTION, DISCONNECT THE APPLIANCE FROM THE MAINS AND CONTACT YOUR NEAREST TECHNICAL SERVICE CENTRE. DO NOT ATTEMPT TO REPAIR THE APPLIANCE.

EACH TIME YOU FINISH USING THE COOKING HOB, ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN "ZERO" POSITION (OFF).

Page 7

Warnings

NEVER PUT INFLAMMABLE OBJECTS INTO THE OVEN: SHOULD IT BE ACCIDENTALLY SWITCHED ON, A FIRE MAY BREAK OUT. IN THE EVENT OF A FIRE: CLOSE THE MAIN GAS SUPPLY AND CUT OFF THE ELECTRIC CURRENT. DO NOT THROW WATER ON BURNING OR FRYING OIL. DO NOT STORE INFLAMMABLE OBJECTS OR AEROSOL CANS NEAR THE APPLIANCE AND DO NOT SPRAY NEAR THE BURNERS WHEN SWITCHED ON. DO NOT WEAR BAGGY CLOTHES OR ACCESSORIES THAT ARE NOT CLOSE TO THE BODY WHEN THE BURNERS ARE SWITCHED ON: SERIOUS INJURIES CAN BE CAUSED BY BURNING FABRIC. DO NOT STORE FLAMMABLE MATERIALS IN THE STORAGE DRAWER.

DO NOT REST SAUCEPANS THAT DO NOT HAVE A PERFECTLY SMOOTH, EVEN BASE ON THE COOKING HOB.

DO NOT USE RECEPTACLES OR STEAK GRILLS THAT EXCEED THE OUTER PERIMETER OF THE COOKING HOB.

THE IDENTIFICATION PLATE WITH THE TECHNICAL DATA, SERIAL NUMBER AND THE MARK IS CLEARLY VISIBLE ON THE BACK OF THE APPLIANCE.

THE PLATE MUST NEVER BE REMOVED.

THE APPLIANCE SHOULD ONLY BE USED BY ADULTS. DO NOT ALLOW CHILDREN TO APPROACH OR PLAY

WITH THE APPLIANCE. NEVER STORE ITEMS THAT CHILDREN MAY ATTEMPT TO REACH ABOVE THE APPLIANCE. THE HEATING UP OF SOME PARTS OF THE APPLIANCE AND OF THE USED PANS MAY BE A DANGER, SO DURING FUNCTIONING AND DURING ALL THE TIME NECESSARY FOR THE COOOLING DOWN, TAKE CARE TO POSITION THE HOT PANS IN A WAY TO PREVENT BURNS OR OVERTURNING. AVOID LEAVING THE OVEN DOOR OPEN DURING FUNCTIONING OR IMMEDIATELY SOON AFTER THE SWITCHING OFF. AVOID TOUCHING THE HEATING ELEMENTS INSIDE THE OVEN AND GRILLS AS WELL.

RESTING OR SITTING ON THE OPEN OVEN DOOR, DRAWERS OR STORAGE COMPARTMENT CAN OVERTURN THE APPLIANCE, AND CONSEQUENTLY CAUSE HARM. THE DRAWERS HAVE A DYNAMIC CAPACITY OF 25 KG.

IF THE COOKER IS SET ON A PEDESTAL, APPROPRIATE MEASURES MUST BE TAKEN TO PREVENT IT FROM

SLIDING OFF THE PEDESTAL.

WHEN THE APPLIANCE IS DECOMMISSIONED, IT MUST BE DISPOSED OF IN A SUITABLE RECYCLING CENTRE. CUT OFF THE MAINS POWER CORD AFTER UNPLUGGING IT FROM THE WALL OUTLET, AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS FOR CHILDREN (DOORS, ETC.).

The manufacturer declines any responsibility for damage incurred by persons or objects that is caused by not following the above guidelines or by tampering with any part of the appliance or by using non-original spare parts.

Page 8

Instructions for the installer

3. Installation

DIMENSIONS OF THE COOKERS

3.1 General warnings

This appliance shall be installed only by authorised personnel and in accordance with the manufacturer’s installation instructions, local gas fitting regulations, municipal building codes, water supply regulations, electrical wiring regulations, AS 5601/AG 601 - Gas Installations and any other statutory regulations. Before using the appliance, remove the

protective plastic on the control panel, stainless steel parts, etc...

The manufacturer declines any responsibility for damage incurred by persons, animals or objects that is caused by not following the above guidelines (cfr. chapter “2. Warnings for safety and use”).

The technical data is indicated on the plate located on the back of the appliance. The adjustment conditions are shown on a label applied to the packing and the appliance.

Do not use the oven door handle for handling the appliance, or for removing the appliance from the packing.

Page 9

Instructions for the installer

3.2 Fitting the adjustable feet

Before turning the cooker over, we recommend removing all the parts that are not stably attached to it, in particular the cooking hob grids and burners. To lighten the weight of the cooker, the accessories inside the oven may also be removed, thereby preventing accidental damage during the overturning operation.

The cooker is delivered with the feet removed. Before moving and hooking up the cooker, take the feet from the packing and screw them onto the cooker. This can be done in one of two ways:

A Lifting the cooker off the floor. B Laying the cooker on its back.

The final regulation of the feet to level the cooker to the floor will be done after the

gas and electric hook-ups have been made.

Should it be necessary to drag the cooker, screw the feet in completely and carry out the final regulation only when the other operations are completed.

3.3 Fitting the front moulding

For the 70 cm model with double oven, a front moulding is included as standard supply to complete the aesthetic lines of the cooker.

To assemble, proceed as follows:

• Tilt the cooker backwards.

• Align the moulding A with the mounting position as shown in the illustration.

• Apply the moulding until it fits into the mounting position.

• Pull the moulding downward so that it hooks onto the 4 pins B (2 for each end) present on the

cooker.

Page 10

Instructions for the installer

3.4 Electric connection

Make sure that the voltage and the size of the mains correspond to the specifications shown on the plate located on the back of the appliance.

The plate must never be removed.

The plug at the end of the power supply cable and the wall socket must be the same type and must comply with current electric standards. Check that the mains is adequately earthed. Once the appliance has been installed make sure that the plug is accessible to allow the periodical check-up.

Prepare an omni-polar cutoff device on the power supply line of the appliance with a contact opening distance equal to or more than 3 mm, located in a convenient position near the appliance.

Do not use reducers, adapters or shunts.

Before making the electric connection, make sure of the efficiency of the earthing.

Make sure that the relief valve and the home wiring system are able to withstand the appliance load.

The yellow/green earth cable must not be subject to cutoffs.

The electric cable must not come into contact with parts whose temperature is more than 50°C higher than room temperature.

3.4.1 Electric power cable section

According to the type of power supply, use a cable that conforms to the following table.

Running at 415 Vac 3Ph N (models connected according to DIAGRAM "A"): use a pentapolar cable type H05RR-F/H05RN-F

(cable measuring 5 x 2.5 mm2).

Running at 240 Vac 1Ph N (models connected according to DIAGRAM "B"): up to 10.44 MJ use a tripolar cable type H05RRF/H05RN-F (cable measuring 3 x 1.5 mm2); between 10.44 MJ and

19.44 MJ use a tripolar cable type H05RR-F/H05RN-F (cable

measuring 3 x 2.5 mm2). The end to be connected to the appliance must have the earth wire

(yellow-green) at least 20 mm longer. The cable type H05RN-F is to be used for the models with fryer,

while cable type H05RR-F for those without fryer.

Page 11

Instructions for the installer

3.4.2 Type of power supply

It is possible to obtain different connections according to the voltage, simply by moving the unconnected cable ends on the terminal board as shown in the following diagrams. According to the model, consult the table "C

ONNECTION TO THE TERMINAL BOARD".

DIAGRAM CONNECTION TO THE TERMINAL BOARD

“A” MODEL

POWER

CURRENT

DRAW (amps)

COOKER 4 BURNERS (1 OVEN) 2,2 9

COOKER 6 BURNERS (1 OVEN) 2,9 12

COOKER 4 BURNERS (1 OVEN) + B / T / C 5,3 22

COOKER 4 BURNERS (1 OVEN) + F 5,1 21

COOKER 4 BURNERS (1 OVEN) + G 5,4 22

COOKER VITROCERAMIC HOB (1 OVEN) (4 HEATING ELEMENTS) 9,8 40

COOKER VITROCERAMIC HOB (1 OVEN) (5 HEATING ELEMENTS) 12,7 52

COOKER 6 BURNERS (2 OVENS) 3,9 16

COOKER 8 BURNERS (2 OVENS) 4,6 19

COOKER 4 BURNERS (2 OVENS) 4,7 19

“B”

COOKER 4 BURNERS (2 OVENS) + B / T / C 6,3 26

COOKER 4 BURNERS (2 OVENS) + F 6,1 25

COOKER 4 BURNERS (2 OVENS) + G 6,4 26

COOKER 6 BURNERS (2 OVENS) + B / T / C 7,0 29

COOKER 6 BURNERS (2 OVENS) + F 6,8 28

COOKER 6 BURNERS (2 OVENS) + G 7,1 29

COOKER 4 BURNERS (2 OVENS) + B / T + C 9,4 39

COOKER 4 BURNERS (2 OVENS) + B / T + F 9,2 38

COOKER 4 BURNERS (2 OVENS) + B / T + G 9,5 39

COOKER VITROCERAMIC HOB (2 OVENS) (5 HEATING ELEMENTS) 13,7 56

COOKER VITROCERAMIC HOB (2 OVENS) (4 HEATING ELEMENTS) 12,3 51

B = STEAK GRILL

T = FRY-TOP

C = VITROCERAMIC GRIDDLE

F = DEEP FRYER

G = GRILL

Page 12

Instructions for the installer

3.4.3 Replacing the electric cable

To replace the electric cable, it is necessary to access the terminal board. It is located on the back of the appliance, at the top left, as shown in the figure.

To replace the cable, proceed as follows:

• open the terminal board box;

• unscrew the screw A that locks the cable;

• loosen the screw contacts and replace the cable

with one of the same length that corresponds to the specifications in the table in section “3.4.1 Electric power cable section”;

• the "yellow-green" earth wire must be connected to the terminal

and must be approximately 20 mm

longer than the line cables;

• the neutral "blue" wire must be connected to the terminal marked with the letter N;

• the line wire must be connected to the terminal marked with the letter L.

3.5 Power consumption of the vitroceramic hob

The vitroceramic hob has different power consumptions depending on the type of heating element used. The diagram shows the values of the power consumed. In the envisaged cases, the first numeric value refers to the total power, whereas the value that follows the symbol "/" refers to the inside diameter, with the exception of the central heating element, whose value that follows "/" refers to the outer diameter.

3.6 Power consumption of the volcanic rock grill

The volcanic rock grill has a consumption of 2500W. This appliance must therefore be installed where this power consumption can be ensured in total safety.

Page 13

Instructions for the installer

3.7 Ventilation in rooms with gas appliances

This appliance is not connected to an exhaust device for products of combustion. Ventilation must be in accordance with AS5601/AG 601 - Gas Installations. In general, the appliance should have adequate ventilation for complete combustion of gas, proper flueing and to maintain temperature of immediate surroundings within safe limits. Pay particular attention to standards applied to room aeration.

This appliance can only be installed in ventilated rooms, according to current standards, so as to allow, with openings onto external walls or appropriate ducts, for correct natural or forced ventilation that permanently and sufficiently ensures both the air intake necessary for correct combustion and the expelling of vitiated air. It is recommended that the appliance have a rangehood fitted directly above or ceiling fan in close proximity to the appliance.

In all other cases, i.e. when other gas appliances are present in the same room, or, if it is not possible to have natural direct ventilation, it is necessary to create natural, indirect ventilation or forced ventilation: for this type of operation, it is necessary to contact a authorised person for

installing and creating the ventilation system in strict compliance with the guidelines set out in current standards.

The openings should be positioned so as not to allow the formation of any unpleasant air current for the occupants. Furthermore, it is forbidden to use flues already used by other appliances to expel products of combustion.

3.8 Gas connection

Gas-powered devices for home use, which are not connected to a conduit for the evacuation of combustion products, must not cause a concentration of carbon monoxide that could pose a health risk to the persons exposed in relation to the time of exposure.

We recommend checking that the appliance is properly set up for the type of gas distributed. The connection to the gas pipes must be made in a workmanlike manner, in compliance with current standards that prescribe the installation of a safety tap at the end of the pipe. The Gas Connection is male ½" BSP and is situated at the left hand, top rear of the appliance, 74mm from the side and 700mm from the floor (cookers) or 25mm from the underside (cooktops). The appliance is factory set for Natural gas. The test point pressure should be adjusted to 1.00kPa with the Wok and Semi-Rapid burners operating at maximum on 120cm models and the Wok burner operating at maximum on 90cm models.

For propane a pressure regulator set to provide a supply pressure of 2.75kPa conforming to standards regulations in force should be fitted. The seals must conform to standards regulations in force. Fit the test point assembly supplied with the appliance to the gas connection when installing for use with Propane Gas. Once the gas has been connected, check the seal of the unions with a soap and water solution.

It is possible to connect the gas in the following ways:

• using iron or copper rigid pipe as specified in AS5601 table 3.1;

• using a Plumbezy flexible hose, AGA approval number 6196, 10mm ID, class D and between

1-1.2m long in accordance with AG601 for a "high level connection". For cookers supplied with a flexible hose the restraining chain fitted to the rear of the cooker must be fixed to the wall as follows.

1. Supply fixing points on either side of the cooker (vertically in line with the chains attached) at approxiametely 100mm above floor level.

2. Firmly secure the chains at these points.

3. Supply similar fixing points at approxiametely 700mm above floor level using open hooks.

4. Loop the chains over these hooks to prevent the cooker from accidentally tilting.

5. Removing the chains from the hooks enables the cooker to be pulled out for service. Ensure that the chains prevent stress on the hose assembly while the cooker is in this position.

Page 14

Instructions for the installer

• Do not allow the pipes to be constricted or crushed;

• Pipes must not be subject to tractive force or torsional stress;

• Do not allow the pipes to come into contact with cutting or sharp edges, etc...

• Do not allow the pipes to come into contact with parts that can reach temperatures of 70°C

above room temperature;

• Make sure the entire length of the pipes can be inspected.

• Do not use the Natural Gas Regulator supplied with the appliance for Propane Gas.

The unit must be coated in heat-resistant material (minimum 90°C). If the appliance is installed close to other units, the minimum space suggested in the following diagram must be left.

Any adjoining wall surface situated within 200mm from the edge of any hob burner must be a suitable non-combustible material for a height of 150mm for the entire length of the hob. Any combustible construction above the hotplate must be at least 600mm above the top of the burner and no construction shall be within 450mm above the top of the burner. Where the distance from the edge of any burner to a horizontal surface is less than 200mm, the surface must be either: 10mm (min) below the level of the hob, or have the vertical component of the surface suitably covered with a non-combustible material as specified in AS 5601 - AG 601.

Page 15

Instructions for the installer

3.9 Gas adjustments

For cooktops, the Data Label is located on the underside of the appliance. A duplicate label is

supplied to adhere in an accessible area adjacent to the appliance. For cookers, the label is situated in the appliance drawer. This appliance is suitable for Natural Gas and Propane; ensure that the available gas supply matches the Data Label. If the cooking appliance is set up for a different type of gas than that available, its injectors must be replaced, the minimum flow regulated and the rubber-holder changed. In order to replace the injectors in the cooking hob, it is necessary to carry out the following operations:

• remove the grids;

• remove the burners and burner caps (Fig. A);

• take out the injector (Fig. B) and replace it with one

suitable for the new type of gas (see "G

ENERAL

INJECTORS TABLE

" on page 16);

• replace the gas label (on the rear of the appliance) with the new one provided with the injectors kit;

• refit all parts by following the disassembly instructions in reverse order and taking care to position the burner cap correctly on the burner.

3.9.1 Minimum flow of valved cooking hob taps

• Switch on the burner and turn the control knob towards the minimum flow position ;

• remove the knob;

• using a screwdriver, adjust the internal screw Z

until the correct low flame is obtained;

• refit the knob.

3.9.2 Minimum flow of non-valved cooking hob taps

• Switch on the burner and turn the control knob towards the minimum flow position ;

• remove the knob;

• insert a small screwdriver into the rod of the tap

and adjust the internal screw Z until the correct low flame is obtained;

• refit the knob.

• Unscrew the adjustment screw Z to increase the flow, or tighten it to reduce the flow.

• The adjustment is correct when the low flame measures approximately 3 or 4 mm.

• For propane the adjustment screw should be tightened all the way.

• When changing quickly from maximum to minimum flow and vice versa make sure that the

flame does not go out.

3.10 Connecting to LPG

Use a pressure regulator and connect to the cylinder in compliance with the guidelines set out in standards regulations in force. When converting from Natural Gas to Propane ensure that the NG regulator is removed and replaced with the Test Point Assembly. A gas regulator suitable for a supply pressure of 2.75kPa should be part of the gas tank supply and should be adjusted with the Wok burner operating at maximum. Replace the old data plate with one which is suitable for the type of gas for which the appliance has been regulated.

Page 16

Instructions for the installer

The hob is made up of the 4 indicated modules:

• modules 1 and 4 are featured on all the

cookers;

• modules 2 and 3 are included depending on

which cooker is purchased and can be replaced with electric modules (fry-top, steak grill, grill, vitroceramic hob or deep fryer).

GENERAL INJECTORS TABLE

CONSUMPTION

TYPE OF GAS

kPa

NOZZLE NO.

BURNERS

POSITION TYPE

MAX.

1.50 RAPID (A) 11.2

1.20 SEMI RAPID (B) 7.2

0.90 AUXILIARY (C) 4.1

1.60 TRIPLE-RING (D) 12.7

NATURAL GAS 1.00

1.20 FISH KETTLE (E) 7.2

0.95 RAPID (A) 11.5

0.73 SEMI RAPID (B) 7.0

0.53 AUXILIARY (C) 3.6

1.00 TRIPLE-RING (D) 12.7

LPG 2.75

0.75 FISH KETTLE (E) 7.3

4. Final operations

4.1 Levelling the cooker to the floor

After having made the electrical and gas hook-ups, level the cooker to the floor using the adjustable feet that were previously screwed onto the bottom of the cooker.

Should it be necessary to drag the cooker, screw the feet in completely and carry out the final regulation only when the other operations are completed.

Check all connections for gas leaks with soap and water. DO NOT use a naked flame for detecting leaks. Ignite all burners to ensure correct operation of gas valves, burners and ignition. Turn gas taps to low flame position and observe stability of the flame. When satisfied with the hotplate, please instruct the user on the correct method of operation. In case the appliance fails to operate correctly after all checks have been carried out, refer to the authorised service provider in your area.

Page 17

Instructions for the user

5. Description of controls

5.1 The front panel

All the commands and controls for the cooking hob and oven are on the front panel.

CONTROL PANEL

DESCRIPTION OF HOB BURNER KNOB

The flame is lit by simultaneously pressing and turning the knob anticlockwise to the low flame symbol . To regulate the flow of the flame, turn the knob to between the maximum and minimum settings. Turn off the burner by returning the knob to position .

LAYOUT OF BURNERS – Description of symbols

REAR LEFT

REAR RIGHT

REAR CENTRE LEFT

REAR CENTRE RIGHT

CENTRE FRONT

CENTRE REAR

FRONT CENTRE LEFT

FRONT CENTRE RIGHT

FRONT LEFT

FRONT RIGHT

Page 18

Instructions for the user

DESCRIPTION OF DEEP FRYER KNOB

The knob of the thermostat that controls the temperature of the heating element can be adjusted between 0° and 200°C. There are also two warning lights: the red light signals the deep fryer is working; the orange light switches on while the appliance is heating. When the preset temperature is reached, the orange light switches off. If the temperature of the oil should decrease while frying, the appliance automatically begins to heat and the orange light switches on until the temperature set on the thermostat knob is reached.

DESCRIPTION OF FRY-TOP / STEAK GRILL AND GRILL KNOB

FRY-TOP/STEAK GRILL: is equipped with differentiated heating. The entire

cooking surface can be used, or only one of the two halves, front or rear. The knobs that regulate the energy individually control the temperature of the two heating elements. A red light indicates that the appliance is heating.

GRILL: two warning lights give essential information on how the appliance is working. The orange light switches on to indicate that the appliance is powered (ON). A red light indicates that the heating element is heating up.

LAYOUT OF HEATING ELEMENTS - Description of symbols

REAR

FRONT

DESCRIPTION OF TIMER KNOB (DEEP FRYER AND GRILL) A spring-loaded timer with bell makes checking the frying time easier. Turn the knob all the way clockwise to wind the timer. It is possible to set the required time up to a maximum of 60 min. The bell rings briefly when the preset time has elapsed. The timer has no effect on the heating of the deep fryer or the grill.

DESCRIPTION OF VITROCERAMIC HOB KNOBS Besides the normal knobs that regulate the energy, the vitroceramic hob is equipped with knobs for differentiated heating. Settings from 1 to 11 control the heating of the internal element, setting the knob to the symbol the outer element also operates.

LAYOUT OF HEATING ELEMENTS - Description of symbols

REAR LEFT

REAR RIGHT

FRONT LEFT

FRONT RIGHT

CENTRAL

Page 19

Instructions for the user

DESCRIPTION OF ELECTRIC OVEN KNOBS

The electric oven is controlled by two knobs: function switch knob and thermostat knob. They allow you to

choose the most suitable type of heating for different cooking requirements, by switching on the heating elements appropriately and setting the required temperature (from 50°C to MAX).

Below the oven knobs there are two warning lights: the red light signals the oven is working; the orange light indicates that the preset temperature has been reached. The orange light switches on and off to indicate when the heating automatically kicks in to maintain the temperature inside the oven at the level set on the thermostat knob.

The oven has an internal light. The light is always on while the oven is working: it can be switched on while the oven is off, for cleaning purposes, by turning the function switch knob to the symbol

DESCRIPTION OF SYMBOLS ON FUNCTION SWITCH KNOB

SWITCH ON LIGHT INSIDE OVEN

GRILL-FAN ELEMENT

UPPER AND LOWER HEATING ELEMENTS

UPPER AND LOWER HEATING ELEMENTS – FAN

UPPER HEATING ELEMENT

HEATING ELEMENT-CONVECTION

LOWER HEATING ELEMENT

DEFROST

GRILL ELEMENT

DESCRIPTION OF AUXILIARY ELECTRIC OVEN KNOB

Some cooker models are equipped with an auxiliary electric oven with natural convection, controlled by a single knob. This allows the user to choose the most suitable type of heating for different cooking requirements, by switching on the heating elements appropriately and setting the required temperature (from 60 to MAX). Using the same knob it is also possible to set the functions described in the table.

Below the auxiliary oven knob there is an orange light, which indicates when the oven has reached the set temperature. The orange light switches on and off to indicate when the heating automatically kicks in to maintain the temperature inside the auxiliary oven at the level set on the control knob.

The auxiliary oven has an internal light. The light is always on while the oven is working: it can be switched on while the oven is off, for cleaning purposes, by turning the function switch knob to the symbol

DESCRIPTION OF SYMBOLS ON AUXILIARY ELECTRIC OVEN KNOB

SWITCH ON LIGHT INSIDE OVEN

UPPER HEATING ELEMENT

60÷MAX

UPPER AND LOWER HEATING ELEMENTS

GRILL ELEMENT + SPIT

LOWER HEATING ELEMENT

Page 20

Instructions for the user

DESCRIPTION OF GRILL OVEN KNOB

The electric oven, equipped with function grill with natural convection, is controlled by a single knob. By positioning the knob appropriately and by setting the required temperature, both upper and lower heating elements will switch on. It is possible to set one of the functions described in the table, but in this case the temperature of the chosen heating element will be automatically set to the MAX temperature value.

Below the grill oven knob there is an orange light, which indicates when the oven has reached the set temperature. The orange light switches on and off to indicate when the heating automatically kicks in to maintain the temperature inside the grill oven at the level set on the control knob.

The grill oven has an internal light. The light is always on while the oven is working: it can be switched on while the oven is off, for cleaning purposes, by turning the knob to the symbol .

DESCRIPTION OF SYMBOLS

SWITCH ON LIGHT INSIDE OVEN

UPPER HEATING ELEMENT

50÷MAX

UPPER AND LOWER HEATING ELEMENTS

GRILL ELEMENT

LOWER HEATING ELEMENT

DESCRIPTION OF CONVECTION OVEN KNOB

The convection oven is controlled by a single knob. This allows the user to choose the most suitable type of heating for different cooking requirements by setting the required temperature value (from 50°C to MAX).

Below the convection oven knob there is an orange light, which indicates when the oven has reached the set temperature. The orange light switches on and off to indicate when the heating automatically kicks in to maintain the temperature inside the convection oven at the level set on the control knob.

The oven has an internal light. The light is always on while the oven is working.

Page 21

Instructions for the user

DESCRIPTION AND USE OF THE END OF COOKING DISPLAY ON THE ELECTRIC OVEN

The end of cooking display electronically checks the operation of the oven. Programming the display allows the user to set the oven to switch on and off at set times.

TIMER BUTTON

COOKING TIME BUTTON

END OF COOKING BUTTON

MANUAL OPERATION BUTTON

DECREASE VALUE BUTTON

INCREASE VALUE BUTTON

SETTING THE TIME

When using the oven for the first time, or after a power cut, the display flashes regularly indicating

Press button

to stop the flashing. Press the value variation buttons or within 5 seconds to increase or decrease by one minute at a time. Press one of the two value variation buttons until the current time appears.

Before setting the end of cooking display, it is necessary to select the required function and temperature. The function P is not enabled.

SEMIAUTOMATIC COOKING

This setting automatically switches off the oven at the end of the cooking. Press button

and the display lights up showing the figures ; hold down and press at the

same time the value variation buttons

or to set the cooking time.

Release the button

to begin the count of the programmed cooking time and the display shows

the current time together with symbols AUTO and

AUTOMATIC COOKING

This setting switches the oven on and off automatically. Press button

and the display lights up showing the figures ; hold down and press at the

same time the value variation buttons

or to set the cooking time.

Press button

to display the sum of the current time plus the cooking time: hold down and press

at the same time the value variation buttons

or to set the end of cooking time.

Release the button

to begin the programmed count and the display shows the current time

together with symbols AUTO and

After the setting, press button to see the remaining cooking time. Press button to see the end of cooking time.

END OF COOKING

At the end of the cooking, the oven switches off automatically and at the same time an intermittent bell rings. After deactivating the bell, the display once again shows the current time together with symbol

, which signals the oven has returned to manual conditions.

Page 22

Instructions for the user

ADJUSTING THE VOLUME OF THE BELL

The volume of the bell can be varied (on 3 levels) while it is operating by pressing button

DEACTIVATING THE BELL

The bell automatically stops ringing after seven minutes. It is possible to deactivate it manually by pressing button

After pressing button the oven begins to operate once again: to switch it off, turn the function switch knob and the thermostat knob to “0”.

It is also possible to deactivate the bell by pressing any one of the function buttons. The oven switches off regardless of the function or set temperature and the AUTO symbol flashes. To stop

the AUTO symbol flashing, press button

, turn the function selector switch and thermostat to "0".

TIMER The end of cooking display can also be used as a simple timer.

Using the display as a timer does not interrupt the operation of the oven at the end of the set time.

Press button

and the display shows the figures ; hold down and press at the same time

the value variation buttons

or . Release the button to begin the programmed count and the

display shows symbols

and .

After programming the timer, the display once more shows the current time. To display the time remaining, press button .

Setting inconsistent values is logically prevented (e.g. the end of cooking display does not accept a contrast between an end of cooking time and a longer cooking time).

DELETING SET DATA

With the program set, hold down the button of the function you wish to delete while at the same time reaching value with the value variation buttons or . Deleting the cooking time is interpreted by the display as the end of the cooking.

MODIFYING SET DATA

The data set for cooking can be modified at any moment by holding down the button of the function and at the same time pressing the value variation buttons

or .

Page 23

Instructions for the user

6. Using the cooking hob

Make sure that the flame caps, the burner caps and the grids are fitted correctly.

During normal operations, the appliance heats up considerably. Caution should therefore be used. Do not allow children to approach the appliance. Do not leave the cooking hob unattended while it is on.

6.1 Switching on the burners

All the hob burner knobs have the following symbols:

tap closed

high flame

low flame

The low flame setting is found by turning the knob anticlockwise all the way. All intermediate settings must be selected between the high flame and low flame, never between high flame and closed.

6.1.1 One-touch lighting

The hob burners are equipped with a "one-touch" lighting system. To switch on one of the burners, press the knob corresponding to the required burner and turn it anticlockwise to the low setting

. Hold down the knob to activate the automatic "one-touch" lighting system. When the burner is on, hold down the knob for approximately 10 seconds, to allow the safety valve to open. In the event of a power cut, the burner can also be lit with a match (see section “6.1.2 Manual lighting”).

Should the burner switch off accidentally, the safety thermocouple blocks the gas flow, even when the tap is open.

Appliances not equipped with safety valve: it is not necessary to hold down the knob (the burner is immediately operative). Take care, however, as if the flame should go out accidentally, gas will continue to come out of the burner.

The device should not been activated for longer than 15 seconds. If after that time it fails to operate stop pressing the knob, open the window and wait 1 minute before trying again. In case the flame goes out accidentally turn off the knob and do not try to switch on the burner for at least 1 minute.

6.1.2 Manual lighting

To light one of the burners, move a lit match towards the burner, press the corresponding knob and turn it anticlockwise to the minimum setting

. Release the knob.

6.2 Switching off the burners

At the end of the cooking, return the knob to position .

6.3 Abnormal Operation

Any of the following are considered to be abnormal operation and may require servicing:

• Yellow tipping of the hob burner flame.

• Sooting up of cooking utensils.

• Burners not igniting properly.

• Burners failing to remain alight.

• Burners extinguished by cupboard doors.

• Gas valves, which are difficult to turn.

In case the appliance fails to operate correctly, contact the authorised service provider in your area.

Page 24

Instructions for the user

7. Using the deep fryer

During normal operations, the surface of the deep fryer heats up considerably. Do not allow children to approach the deep fryer. Do not leave the deep fryer unattended while it is on. Oil or

fat in bad condition may burst into flames.

When using the burners we recommend removing the safety cover A (only available on certain models).

7.1 Before switching on the deep fryer

The first time it is used, the deep fryer may develop an acrid or burnt smell caused by oily residue from manufacturing that may give unpleasant odours or flavours to fried food. To eliminate this problem, clean the vat, basket and heating element before use.

Proceed as follows:

• wash the basket in warm water and detergent;

• pour warm water into the deep fryer vat and add detergent for stainless steel surfaces;

• carefully wash the vat and the heating element;

• lift the heating element upwards, rinse

and dry;

• lock the heating element by moving the

lock system S towards the left as shown in the figure;

• remove the frying vat, rinse away the

soapy water with running water;

• dry the vat and return it to its working

position;

• release the lock system S and lower

the heating element into the vat.

7.2 How to fry

Proceed as follows:

• pour 3 litres of oil into the deep fryer vat. It is also possible to fry with fat: in this case, chop up

approximately 3.5 kg of frying fat.

• Switch on the heating element (see below for relative instructions).

• If using fat, leave it to melt slowly in the deep fryer vat.

To avoid abnormal overheating: until the heating element is completely covered with melted fat, we recommend switching the heating element on and off repeatedly by using the thermostat knob.

• Heat the oil or fat to a maximum of 190°C. This temperature should not be exceeded,

otherwise the oil or fat would overheat and change consistency.

The heating element should never be switched on unless the frying vat contains the above mentioned quantity and type of oil or fat.

The appliance is now ready for frying. Proceed as follows:

• use the thermostat knob to set the required degree of heating: the deep fryer starts to operate

and the red and orange lights switch on;

• wait until the orange light switches off, which means that the frying liquid has reached the

preset temperature;

• place the food to be fried in the basket and lower it very slowly into the frying vat;

Page 25

Instructions for the user

• lift the basket periodically to check the frying. When the food is

crisp as required, remove the basket completely from the frying liquid and shake it lightly to remove excess liquid;

• hang the basket on the element of the deep fryer (as shown in

the figure) and allow to drip.

Each time the deep fryer has been used, check the level of frying liquid.

Check the level of frying liquid by lifting out the basket and checking that the level is between the two minimum and maximum marks punched on the wall of the frying vat.

The water contained in food goes to the bottom of the frying vat, into the so-called cold area. In this way, it is practically impossible for the frying liquid to overflow out of the vat. Food particles that come out of the basket while cooking also go to the cold area.

7.2.1 Tripping of the temperature limiting device

The deep fryer is equipped with a temperature limiting device in the vat. In the event that the frying liquid temperature exceeds the preset value, this device cuts off the heating (both lights switch off). To reactivate the heating of the deep fryer, rearm the limiting device manually.

Proceed as follows:

• wait until the frying liquid has cooled down;

• lift the heating element upwards and remove the frying vat from

the deep fryer;

• press the small red pushbutton on the bottom of the vat

compartment, whose position is shown in the figure;

• replace the frying vat into its working position and lower the

heating element.

• It is now possible to reactivate heating (red and orange lights

on).

Should the appliance unexpectedly turn off after following the above instructions, switch off the master power switch and contact the Technical Service.

7.3 Indicative frying times

The frying times indicated in the table are approximate and vary according to the condition of the food and personal taste.

FOOD FRYING TIME HEATING

Chicken (1100 g) 20 min.

(turn after 10 min.)

190°C

Fries (500 g frozen) 6 min. 190°C Fries (500 g frozen) repeat 2 min. 190°C Milanese cutlet (370 g) 5 min. 170°C Sliced onions (approx. 500 g) 5 min. 190°C

7.4 Switching off

After frying, return the thermostat knob to position "0".

Page 26

Instructions for the user

8. Using the fry-top / steak grill

During normal operations, the appliance heats up considerably. Caution should therefore be used. Do not allow children to approach the appliance. Do not leave the fry-top/steak grill unattended while it is on.

Depending on the model, the appliance is fitted with a fry-top with smooth griddle, or a steak grill with lined griddle.

FRY-TOP STEAK GRILL

When using the burners we recommend removing the safety cover A (only available on certain models).

8.1 Before switching on the fry-top / steak grill

The first time it is used, the fry-top/steak grill griddle may develop an acrid or burnt smell caused by oily residue from manufacturing that may give unpleasant odours or flavours to food. To eliminate this problem, clean the griddle as described in section “13.8 Cleaning the fry-top / steak grill” before use.

8.2 Switching on

The fry-top/steak grill is equipped with differentiated heating. The entire surface of the griddle can be used, or only one of the two halves, front or rear.

Position the control knob of the heating element to the required setting. The red light switches on to indicate the appliance is working. Place the food on the griddle and cook as preferred.

8.3 Energy regulator table

The following table offers only indicative values because, according to the thickness and type of food, as well as personal taste, the heat should be higher or lower.

1 - 4

Maintaining the heat on the griddle

5 - 7

For light cooking

8 - 9

To grill

10 - 11

To grill thicker meat

For rapid warming and cleaning

8.4 Switching off

After cooking, return the knob to position .

Page 27

Instructions for the user

9. Using the volcanic rock grill

During normal operations, the appliance heats up considerably. Caution should therefore be used. Do not allow children to approach the appliance. Do not leave the grill unattended while it is on.

When using the burners we recommend removing the safety cover A (only available on certain models).

9.1 Before switching on the grill

The first time it is used, the grill may develop an acrid or burnt smell caused by oily residue from manufacturing that may give unpleasant odours or flavours to food. To eliminate this problem, clean all its components beforehand as described in section “13.9 Cleaning the volcanic rock grill”.

9.2 Switching on

Proceed as follows:

• Remove the cast iron grill very carefully to

avoid breaking it;

• lift the heating element upwards and lock it,

by moving the lock system

S towards the

left as shown in the figure;

• fill the safety vat with the volcanic rock,

taking care to evenly cover the whole surface, so that it does not go over the edge.

Water (up to 2 litres) can be used in the safety vat instead of volcanic rock. It is advisable to use water when cooking very fatty meat (e.g. sausage, bacon, etc.), as the meat juices will melt instantaneously in the water. This method prevents excessive smoke and simplifies the cleaning operations described in section 13.9.

The heating element should never be switched on unless the safety vat contains the volcanic rock or water as specified above.

• Release the lock system S and lower the

heating element;

• reposition the cast iron grill over the heating

element as shown in the figure. The cast iron grill ensures adequate heat distribution.

• The appliance is ready to be switched on.

Before use, preheat the cast iron grill for 5 or 10 minutes by turning the energy regulator knob to the maximum setting (11). The red light signals the appliance is working.

• Now turn the energy regulator knob to the required setting (see section “9.3 Energy regulator

table”). Place the food on the cast iron grill and cook as required.

Page 28

Instructions for the user

The appliance can also be used in the same way as an “open burner”, which is ideal for simmering. Only use multi-function pans whose dimensions are compatible with the cooking surface of the cast iron grill. This type of cooking is ideal for: beef stews, grilled pork, blanquette, rabbit with beer, tongue.

Proceed as follows:

• preheat the cast iron grill by turning the energy regulator knob to the maximum setting (11) for

a few seconds;

• turn the regulator knob back to the minimum setting (1);

• position the multi-function pan containing the food to be cooked on the cast iron grill;

• put the lid on the pan to keep in humidity or remove to reduce.

9.3 Energy regulator table

The following table offers only indicative values because, according to the thickness and type of food, as well as personal taste, the heat should be higher or lower.

1 - 4

Maintaining the heat on the cast iron grill

5 - 7

For light cooking

8 - 9

To grill

10 - 11

To grill thicker meat

For rapid warming and cleaning

9.4 Switching off

After cooking, return the knob to position .

Page 29

Instructions for the user

10. Using the vitroceramic hob

During normal operations, the appliance heats up considerably. Caution should therefore be used. Do not allow children to approach the appliance. Do not leave the vitroceramic hob unattended while it is on.

10.1 General warnings

The first time it is heated, the vitroceramic hob may develop an acrid or burnt smell caused by oily residue from manufacturing, which disappears completely after repeated use.

The vitroceramic hob is fitted with a cooking area with various diameters and power (see section “3.5 Power consumption of the vitroceramic hob”). Their position is clearly indicated with circles and the heat is delimited within the diameters marked on the glass.

10.2 Switching on

Position the pan or pot with the food to be cooked inside it on the required heating element. Turn the energy regulator knob to the required setting. After a few moments, the latent heat light corresponding to the selected heating element switches on.

If the vitroceramic hob is used to boil water, once it has boiled, turn the energy regulator knob to a lower setting to prevent the liquid in the pot from boiling over and soiling the surface.

Some knobs are fitted with a supplementary heating setting (griddle with dual heating element). To activate it, turn the energy regulator knob to position

10.3 Switching off

After cooking, return the knob to position

The vitroceramic hob features a latent heat light which reproduces in reduced scale the position of the heating diameters. This light signals that the surface area is still hot.

Do not clean or touch the surface until the latent heat light has switched off.

Page 30

Instructions for the user

11. Using the ovens

11.1 General warnings

When the oven or grill is operating, the outer walls and oven door can become very hot.

Keep children away from the appliance. Do not allow children to sit on the oven door or play with it. Do not use the door as a stool. Never stand aluminium pots or foil on the base of the oven, as this may seriously damage the oven enamel.

Do not cook food on the bottom of the oven.

When using the oven for the first time, or after a power cut, the display flashes regularly indicating

. To set the display, refer to section "SETTING THE TIME” on page 21.

Do not attempt to disassemble the oven door without consulting the relative instructions carefully (refer to section “14.1 Removing the oven door”): the hinges on the oven door may injure the hands.

HEATING BLOCK OF THE OVEN

If during normal operation the oven interrupts heating and the programmer display begins to flash and goes to zero, check whether:

• there has been a current interruption.

If the block occurs again after the cooking programme has been restarted, this means that the safety device has been tripped. This device intervenes in the event of a thermostat fault and prevents oven overheating. In such case, we recommend that you not try to light the oven again and that you contact your nearest service centre.

11.2 Drawer

A storage drawer is provided on the lower part of the cooker beneath the oven. Use only to store metal cooker accessories.

Do not store inflammable material such as cloths, paper or similar in the drawer.

11.3 Using the electric multifunction oven

The end of cooking display and the control knobs on the main oven have no bearing on the operation of the auxiliary oven.

11.3.1 Switching on the oven for the first time

The first time it is used, the oven may smoke or give off

an acrid smell caused by oily residue from manufacturing that may give unpleasant odours or flavours to food.

Before putting food in the oven, heat to the maximum temperature for 30-40 minutes with the door closed and wait until the smoke or odour has stopped.

Page 31

Instructions for the user

To prevent any steam in the oven from scalding, proceed as follows: turn the function switch knob to "0", or to function ; open the door in two stages: hold it partly open (approx. 5 cm) for 4-5 seconds, then open it completely. Should you need to adjust the food, leave the door open for as short a time as possible to prevent the temperature inside the oven from lowering to such an extent as to jeopardise cooking.

11.3.2 Traditional cooking

Turn the function switch knob to position and the thermostat knob in correspondence with the required temperature value. For differentiated heating over or below the food, set the function

selector switch to position

(hot above) or (hot below). For more uniform heating throughout

the oven, turn the function switch knob to position

After preheating and putting the food in the oven an air flow between the upper side of the door and the lower side of the hob may be noticed. In case that does not happen, switch off the appliance and contact the Technical Service immediately.

11.3.3 Convection cooking

Turn the function switch knob to position ; turn the thermostat knob in correspondence with the required temperature value.

11.3.4 Cooking with the ventilated grill

Turn the function switch knob to position ; turn the thermostat knob in correspondence with the maximum temperature value (MAX).

11.3.5 Cooking with the grill + roasting spit

Turn the function switch knob to position ; turn the thermostat knob in correspondence with the maximum temperature value (MAX). The grill and spit operate at the same time, allowing for cooking on the spit.

11.3.6 Cooking with the roasting spit

If your oven model has a roasting spit, proceed as follows:

• Slide the meat to be cooked on the spit rod A and secure it with the adjustable forks.

• Hang the hook B at the top of the oven as shown in the figure.

• Place the spit rod A into the hole C in the oven casing; before closing the oven door, make

sure that the rod A is correctly inserted into the hole C (insert the rod and turn it slightly back and forth).

• Hang the other end of the spit rod to the hook B (the

pulley of the rod A is situated on the handle of the hook B).

• Close the oven door and activate the spit by turning

the function selector knob to the

position.

• When cooking is completed, open the oven door and

remove the spit rod using the plastic handle D, which is screwed into the base of the rod A.

11.3.7 Defrosting

Turn the function switch knob to position , turn the thermostat knob to position "0": in this way the motor fan is activated, which moves the air inside the oven and encourages frozen food to defrost.

11.3.8 Switching off the oven

The oven is switched off by returning the thermostat knob to position "0".

Page 32

Instructions for the user

11.4 Using the auxiliary oven with natural convection

The end of cooking display and the control knobs on the main oven have no bearing on the operation of the auxiliary oven.

The auxiliary oven with natural convection is equipped with:

• a heating element positioned on the base of the oven (at the bottom);

• a heating element positioned on the ceiling of the oven (at the top) +

grill.

11.4.1 Switching on the auxiliary oven for the first time

The first time it is used, the auxiliary oven may smoke or give off an acrid smell caused by oily residue from manufacturing that may give unpleasant odours or flavours to food. Before putting

food in the oven, heat the auxiliary oven to the maximum temperature for 30-40 minutes with the door closed and wait until the smoke or odour has stopped.

To start heating the auxiliary oven, select the temperature (from 60 to MAX) or the required function by turning the thermostat knob.

11.4.2 Cooking with the grill (auxiliary oven)

Turn the thermostat knob to position and let the auxiliary oven preheat for approximately 5 minutes. For correct operations, position the grill shelf on the third guide from the bottom. It is however possible to vary the position of the grill shelf according to personal taste and different cooking requirements. Before putting food in the oven, allow it to preheat for 5 minutes. A cooling system prevents the control knobs from overheating.

11.4.3 Cooking with the spit (auxiliary oven)

Turn the thermostat knob to position and let the auxiliary oven preheat for approximately 5 minutes. In the meantime, proceed as follows:

• insert the food on to the spit rod A taking care to hold it firm with the two forks B, and balancing

it so as to avoid straining the gearmotor;

• place the pulley C of the spit rod onto the support D after

introducing the opposite end into the hole E, until the coupling with the gearmotor F so that the rod rotates;

• pour a little water into the dripping pan and position it under the spit

rod;

• monitor the cooking from time to time and check the spit rod is

rotating correctly;

• at the end of the cooking, switch off the auxiliary oven by returning

the thermostat knob to position "0";

• remove the spit rod from the auxiliary oven using the knob G and

wearing an oven glove.

11.4.4 Switching off the auxiliary oven

The oven is switched off by returning the thermostat knob to position "0".

Page 33

Instructions for the user

11.5 Using the convection electric oven

The end of cooking display and the control knob on the convection oven have no bearing on the operation of the grill oven.

The convection oven is equipped with a circular heating element with a fan located on the rear wall of the oven.

11.5.1 Switching on the oven for the first time

The first time it is used, the oven may smoke or give off an acrid smell caused by oily residue from manufacturing that may give unpleasant odours or flavours to food. Before putting food in the

oven, heat to the maximum temperature for 30-40 minutes with the door closed and wait until the smoke or odour has stopped.

To prevent any steam in the oven from scalding, proceed as follows: turn the knob to "0"; open the door in two stages: hold it partly open (approx. 5 cm) for 4-5 seconds, then open it completely. Should you need to adjust the food, leave the door open for as short a time as possible to prevent the temperature inside the oven from lowering to such an extent as to jeopardise cooking.

11.5.2 Cooking with convection oven

Turn the knob in correspondence with the required temperature value. It is possible to vary the position of the grill shelf according to personal taste and different cooking requirements.

11.5.3 Switching off the oven

The oven is switched off by returning the knob to position "0".

Page 34

Instructions for the user

11.6 Using the grill oven with natural convection

The grill oven knob do not influence the functioning of the convection oven.

The grill oven with natural convection is equipped with:

• a heating element positioned on the base of the oven (at the bottom);

• a heating element positioned on the ceiling of the oven (at the top) +

grill.

11.6.1 Switching on the grill oven for the first time

The first time it is used, the grill oven may smoke or give off an acrid smell caused by oily residue from manufacturing that may give unpleasant odours or flavours to food. Before putting food in

the oven, heat the grill oven to the maximum temperature for 30-40 minutes with the door closed and wait until the smoke or odour has stopped.

It is possible to switch on the heating of the grill oven by turning the knob to the required temperature (from 50°C to MAX) or function.

11.6.2 Cooking with the grill

Turn the knob to position and let the grill oven preheat for approximately 5 minutes. For correct operations, position the grill shelf on the second guide from the bottom. It is possible to vary the position of the grill shelf according to personal taste and different cooking requirements. A cooling system prevents the control knob from overheating.

11.6.3 Traditional cooking

For differentiated heating over or below the food, set the function selector switch to position

(hot

above) or

(hot below).

11.6.4 Switching off the grill oven

The oven is switched off by returning the knob to position "0".

Page 35

Instructions for the user

12. Cooking suggestions

12.1 Suggestions for using the hob burners correctly

Burner

Recipient diameter

(in cm)

Rapid from 24 to 26 Semi rapid from 16 to 22 Auxiliary from 8 to 14 Triple-ring from 24 to 26 Fish kettle from 16 to 35

The diameter of the base of cooking recipients should fit the diameter of the burner used (see adjacent table). The burner flame must never be wider than the diameter of the recipient. Use recipients with a flat base. Where possible use pots with a lid, as this allows less power to be used. To reduce cooking times for vegetables, potatoes, etc., use little water.

12.2 Suggestions for using the deep fryer correctly

Do not add salt or spices to food while the basket is still positioned above the frying vat, as the oil or fat would be altered, jeopardising the flavour of subsequent fries. For large quantities of food, we recommend removing the basket from the frying vat every 1-2 minutes, so that the frying liquid can return to the preset temperature more quickly. The food to be fried must always be covered by the frying liquid. Should this not be possible (with chicken for instance), turn it half way through cooking. At the end of the cooking, remove any food residue from the frying liquid. If, despite the correct temperature setting, the food is not crisp and the frying liquid is dark, it should be replaced by carefully following the instructions given in section “13.7.1 Discharging the frying liquid”.

In order to avoid the dangerous combustion of the frying liquid, do not activate the open burners near the deep fryer.

12.3 Suggestions for using the fry-top / steak grill correctly

The fry-top griddle is smooth, whereas the steak grill is lined and can be used to obtain the typical rhomboidal pattern together with the delicious flavour of barbecue cooking. Foods cooked on the fry-top/steak grill have a special taste that does not require the excessive use of spices. It is possible to cook in different ways. For example, different foods, such as meat and fish, can be cooked at the same time. Before cooking meat, we recommend treating it with flavoured oil or marinating it for a few hours. A little tip: meat should always be salted after cooking on the griddle, so that its juices do not come out prematurely.

12.4 Suggestions for using the volcanic rock grill correctly

Cooking food on the cast iron grill creates a considerable quantity of smoke. Sometimes, while cooking very fatty meat, small flames may appear similar to those seen during barbeque cooking (see section 9.2 for how to solve this problem). Before placing fish on the grill, we recommend greasing it slightly with oil or melted butter. This will stop the fish sticking to the surface of the grill.

Page 36

Instructions for the user

12.5 Suggestions for using the vitroceramic hob correctly

In order to obtain good efficiency and adequate energy consumption, it is essential to use only recipients that are suitable for electric cooking. The diameter of the base of the recipient must be the same as the diameter of the outline of the cooking area. Energy is wasted if they do not correspond. The base of the recipient must be very thick and perfectly flat. It should also be clean and dry, as should the glass on the hob. Do not use cast iron pots or pots with a rough base, as they may scratch the surface.

When using the vitroceramic hob, it must be thoroughly cleaned before switching on the heating elements. The glass may be scratched if pans are placed on abrasive residues. Any scratches do not however jeopardise the cooking procedure.

The ideal thickness for the base of the pans is:

• 2-3 mm in enamelled steel;

• 4-6 mm in stainless steel with double base.

Before cooking food with a high sugar content (e.g. jam), apply a protective product to the cooking surface to prevent it from being damaged if the food spits or boils over.

12.6 Suggestions for using the oven correctly

The oven allows to optimise cooking. It is possible to cook traditionally, with convection and with the grill.

The oven door should be completely closed for all types of cooking.

12.6.1 Traditional cooking

With this type of cooking, the heat comes from the top and the bottom. It is therefore preferable to use the central guides. If the cooking requires a hotter temperature from the bottom or from the top, use the lower or upper guides. Traditional cooking is recommended for all food that requires high cooking temperatures, or long brazing times. This system is also recommended when cooking with recipients made of terracotta, porcelain and similar materials.

12.6.2 Convection cooking

With this type of cooking, the food is heated by preheated air that is circulated in the oven thanks to a fan located on the rear wall of the oven. Heat rapidly and evenly reaches all parts of the oven, thus enabling different food to be cooked at the same time on different shelves. Humidity is eliminated from the air and the drier area prevents odours and flavours from being spread and mixed. The possibility of cooking on more than one shelf allows you to cook many different dishes at the same time. Biscuits and mini pizzas can be cooked in three different baking tins. The oven, however, can also be used for cooking on a single shelf. The lower shelves can be used so that it is easier to monitor cooking. Convection cooking is particularly

convenient for bringing frozen food rapidly back to room

temperature, for sterilising preserves or home-made fruit in syrup and, finally, for drying mushrooms or fruit.

Page 37

Instructions for the user

12.6.3 Cooking with the grill

The heat comes from the top. Almost all meat can be grilled, with the exception of lean game and dishes such as meat-loaf. Meat and fish to be grilled should be lightly drizzled with oil and placed on the grid bars, which should be placed in the guides closest to or farthest away from the grill element, depending on the thickness of the meat, so as to avoid burning the surface and cooking too little inside. Suitable for: relatively thin meat; toasted sandwiches.

Pour 1 or 2 glasses of water into the dripping pan to avoid smoke forming due to drops of juice or fat.

While cooking with the grill, the dripping pan should always be positioned in the 1st guide from the bottom.

12.6.4 Cooking with the ventilated grill

Using the combination of grill and fan . This type of cooking allows the heat to penetrate gradually inside the food, even though the surface is directly exposed to the grill.

Suitable for: thicker meat; game-birds.

12.6.5 Cooking meat and fish

Meat to be cooked in the oven should weigh at least 1 kg. Very tender red meat to be cooked rare (roast beef, fillet, etc.), or which should be well cooked on the outside and preserve all its juices on the inside, require cooking on high temperatures for a short time (200-250°C). White meat, gamebirds and fish require cooking on low temperatures (150-175°C). The ingredients for the sauce should only be placed in the baking tin if the cooking time is short, otherwise, they should be added in the last half hour. Meat can be placed on an ovenproof plate or directly on the grid bars, below which the dripping pan should be placed to collect the juice. Press the meat with a spoon to check if it is done. If it is firm, it is cooked. At the end of the cooking, wait at least 15 minutes before cutting the meat so as not to lose the juices. Before serving, plates can be warmed in the oven at minimum temperature.

12.6.6 Baking

Beaten mixtures must stick to the spoon because excess fluidity would prolong the cooking time. Sweets require moderate temperatures (generally between 150-200°C) and require preheating (approximately 10 minutes). The oven door must not be opened until at least ¾ of the way through the cooking time.

Page 38

Instructions for the user

12.6.7 Recommended cooking tables

Cooking times vary according to the nature, homogeneity and volume of the food. We recommend monitoring your first attempts and checking the results, as similar results are obtained by cooking the same dishes in the same conditions. The following three tables (I, II and III) provide guidelines.

TABLE OF CONVECTION AND TRADITIONAL COOKING TIMES (I)

POSITION OF GUIDE

FROM BOTTOM

TEMPERATURE

°C

TYPE OF COOKING

QUANTITY

KG.

CONVECTION TRADITIONAL CONVECTION TRADITIONAL

TIME IN

MINUTES

BAKING

WITH BEATEN MIXTURE, IN A TIN WITH BEATEN MIXTURE, ON THE DRIPPING PAN SHORT PASTRY, PIE BASE SHORT PASTRY WITH MOIST FILLING SHORT PASTRY WITH DRY FILLING MIXTURE WITH NATURAL LEAVENING SMALL CAKES

1 1

0.5

1.5 1 1

0.5

1-3 1-3 1-3 1-3 1-3 1-3 1-3

2 2 3 2 2 1 3

175 175 175 175 175 175 160

200 200 200 200 200 200 175

60 50 30 70 45 50 30

MEAT

VEAL BEEF ENGLISH STYLE ROAST BEEF PORK CHICKEN

1 1 1 1

1-1.5

2 2 2 2 2

180 180 220 180 200

200 200 220 200 200

60 70 50 70 70

STEWS

BEEF STEW VEAL STEW

1 1

2 2

175 175

200 200

120 110

FISH

FILLET, STEAK, COD, HAKE, SOLE MACKEREL, TURBOT, SALMON OYSTERS

1 1 1

1-3 1-3 1-3

2 2 2

180 180 180

30 45 20

TIMBALE

PASTA TIMBALE VEGETABLE TIMBALE SWEET AND SAVOURY SOUFFLÉS PIZZA AND CALZONE

2 2

0.75

0.5

1-3 1-3 1-3 1-3

2 2 2 2

185 185 180 200

200 200 200 220

60 50 50 30

• The times refer to cooking on one shelf only; for more than one shelf increase the time by 5-10'.

• The cooking times do not include preheating which takes approximately 15'.

• When cooking on more than one shelf, the guides are given in the preferential position.

• For beef, veal, pork and turkey roasts, either with bone or rolled, increase the time by 20'.

TABLE OF COOKING TIMES WITH GRILL AND VENTILATED GRILL (II)

TRADITIONAL GRILLING

TYPE OF COOKING QUANTITY

KG.

POSITION OF GUIDE

FROM BOTTOM

TEMPERATURE

°C

TIME IN

MINUTES

CHICKEN TOASTED SANDWICHES SAUSAGES PORK CHOPS FISH

1-1.5

0.5

3 4 4 4 4

MAX MAX MAX MAX MAX

30 PER SIDE

5 PER SIDE

10 PER SIDE

8 PER SIDE 8 PER SIDE

GRILLING WITH VENTILATED GRILL

TYPE OF COOKING QUANTITY

KG.

POSITION OF GUIDE

FROM BOTTOM

TEMPERATURE

°C

TIME IN

MINUTES

ROAST PORK ROAST BEEF CHICKEN

1.5

1.2

2 3 2

170 220 190

180

60 90

• The dripping pan for collecting cooking juices should always be positioned in the 1st guide from the bottom.

TABLE OF DEFROSTING TIMES (III)

DEFROSTING

TYPE OF FOOD QUANTITY

KG.

POSITION OF GUIDE

FROM BOTTOM

TIME IN

MINUTES

READY-TO-EAT DISHES MEAT MEAT MEAT

0.5

0.75 1

2 2 2 2

45 50 70

110

• Defrosting at room temperature has the advantage of not modifying the flavour and appearance of food.

Page 39

Instructions for the user

13. Cleaning and maintenance

Before cleaning or carrying out maintenance, switch off the power supply to the appliance and close the gas tap.

Warning: Servicing should be carried out only by authorised personnel. Do not clean the surfaces of the appliance when they are still hot. Do not use pressure or steam spray guns to clean the appliance.

13.1 Cleaning stainless steel surfaces

To clean and preserve the stainless steel surfaces and remove the toughest stains, always use specific products, provided they do not contain chlorine-based abrasives or acid substances, or a little warm vinegar.

Pour the product onto a damp cloth and wipe the steel surface. Rinse carefully and dry with a soft cloth or a piece of deerskin.

Do not under any circumstances use metallic sponges or sharp scrapers that may damage the surfaces. Only use non-scratch, non-abrasive sponges and, if necessary, wooden or plastic

utensils.

13.2 Cleaning enamelled surfaces

Clean with a non-scratch, non-abrasive sponge dampened with soap and water. Grease stains

can easily be eliminated with hot water or a product specifically made for cleaning enamel. Rinse carefully and dry with a soft cloth or a piece of deerskin.

Do not use products containing abrasives, scouring pads, steel wool or acid, which may spoil the surfaces. Do not leave acid or alkaline substances on the enamel (lemon juice, vinegar,

salt, etc.).

13.3 Cleaning the polished surfaces

Clean with a non-abrasive, scratchproof sponge dampened with warm water and neutral soap or

with a standard detergent for polished surfaces. Rinse and dry carefully with a soft cloth.

Abrasive pastes, coarse wire pads, steel wool or acid will damage the surfaces. Do not use alcohol.

13.4 Cleaning the knobs and the control panel

Clean the knobs and the control panel with a damp cloth.

13.5 Cleaning the grids and burners

To clean the grids and hob burners, remove them from their housing by lifting them upwards as shown in the figure, and immerse them in a solution of warm water and non-abrasive detergent for about ten minutes. Rinse and dry carefully.

Always check that none of the burner openings is clogged.

Be sure to refit the burner correctly, checking the flame is uniform. We recommend carrying out this operation at least once a week and each time it is necessary.

Page 40

Instructions for the user

13.6 Cleaning the igniter plugs and thermocouples

In order for the igniter plugs and thermocouples to operate correctly, they must be kept clean at all times. Check them frequently and, if necessary, clean them with a damp cloth. Any dry residue should be removed with a toothpick or needle, taking care not to damage the insulating ceramic part.

13.7 Cleaning the deep fryer

13.7.1 Discharging the frying liquid

Allow the frying liquid to cool completely before carrying out this operation.

Proceed as follows:

• lift the heating element upwards, leave it to drip on the vat and dry it with kitchen roll;

• lock the heating element by moving the lock system S towards the left as shown in the figure;

• remove the frying vat;

• pour the frying liquid into an appropriate

container and dispose of it according to current standards for the disposal of exhausted oil.

• The deep fryer's stainless steel vat should be cleaned with a specific product that does not contain chlorine-based abrasives or acid substances, or a little warm vinegar;

• rinse and dry the vat and basket thoroughly;

• clean the deep fryer heating element with a non-scratch, non-abrasive sponge and detergent

and then rinse thoroughly;

• replace the deep fryer vat into its working position. Finally, release the lock system S and lower the heating element into the vat.

13.8 Cleaning the fry-top / steak grill

Any grease deposits on the fry-top/steak grill can be eliminated more easily when the griddle is still warm. If necessary, leave it to cool and soak for a few minutes. Finally, clean with warm salted water, dry with a tea cloth or kitchen roll.

After each use, the vitroceramic surface V underneath the fry-top/steak grill should also be cleaned. Any residue of meat or grease can be removed by proceeding as follows:

• remove the fry-top/steak grill from its housing;

• turn the knob to position 11;

• after approximately 20-30 minutes, even the

toughest residue can easily be cleaned off the vitroceramic surface with a wooden spatula;

• switch off the heating and leave to cool, then clean the vitroceramic surface V with specific products;

• dry thoroughly and return the fry-top/steak grill to its working position.

Page 41

Instructions for the user

13.9 Cleaning the volcanic rock grill

After cooking, the cast iron grill and other components will remain hot for a certain length of time. Make sure they are completely cool before handling them for cleaning.

Proceed as follows:

• clean the cast iron grill by immersing it in hot water and washing up liquid. Do not under any circumstances use abrasive or corrosive detergents (e.g. powder products or metallic sponges). Rinse and dry carefully.

While cleaning the grill, handle it with care as it is fragile due to the material it is made of and its thickness.

Any grease deposits can be removed more easily by heating the grill for 5 or 10 minutes (knob in position 11). Allow the grill to cool, remove it, rinse and dry well with a clean cloth.

• Lift the heating element upwards and clean it with a damp sponge;

• lock the heating element by moving the lock system S towards the left as shown in the figure.

• Remove the safety vat. Place the volcanic rock in a suitable container or pour away the water with the cooking fat residue.

The volcanic rock contained in the collection basin is not subject to wear and therefore never has to be replaced. To eliminate any unpleasant odours due to normal use, stir up the stones and heat them for a few minutes. If cooking grease is deposited on the surface of the stones, it is sufficient to heat them in an oven for high temperature pyrolysis. The same quality of cleaning can be obtained by turning the energy regulator knob of the grill to the maximum position (11) for 5 or 10 minutes, depending on the amount of soil that has accumulated. In any case, volcanic rock replacements can be found in any store that sells household goods.

• The stainless steel safety vat should be cleaned with a specific product that does not contain chlorine-based abrasives or acid substances, or a little warm vinegar (it is dishwasher

safe). Rinse and dry carefully;

• replace the safety vat into its working position. Finally, release the lock system S and lower the heating element over the vat.

13.10 Cleaning the vitroceramic hob

The vitroceramic hob must be cleaned regularly, each time it is used if possible, when the latent heat lights are off.

Any light-coloured marks caused by aluminium-based pans can be removed with a damp cloth dipped in vinegar. Any burnt residue left after cooking can be removed with a wooden spatula. Rinse with water and dry well with a clean cloth. Do not under any circumstances use abrasive or corrosive detergents (e.g. powder products, oven sprays, stain-removers or metallic sponges).

Page 42

Instructions for the user

Any grease deposits on the vitroceramic hob can be removed more easily by heating it for approximately 20-30 minutes (knob in position 11). Afterwards, this residue can be cleaned off with a wooden spatula. Allow the surface to cool, rinse with water and dry well with a clean cloth.

In the event that aluminium or plastic marks, sugar or food containing sugar melt on the cooking surface, remove immediately while the surface is still warm with a wooden spatula. This will prevent any damage to the surface.

The cooking surface of the vitroceramic hob is extremely resistant. It is not however unbreakable and may be damaged, above all by pointed or hard objects if dropped onto it with a certain force.

Warning! If any crack should appear on the hob, isolate the cooker from the main supply and do not use the appliance to avoid electrocution. Call Customer Services immediately.

13.11 Cleaning the oven

In order to preserve the oven well, it should be cleaned regularly, each time it is used if possible, after leaving it to cool: in this way it is possible to remove any residue more easily, preventing it from burning the next time the oven is used.

Clean the stainless steel parts and enamelled parts as described in the corresponding sections “13.1 Cleaning stainless steel surfaces” and “13.2 Cleaning enamelled surfaces”.

Take out all the removable parts and wash them separately. Rinse and dry thoroughly with a clean cloth.

13.11.1 Cleaning the oven walls

Never use detergent products to clean this type of oven.

The walls of the oven can be cleaned using white vinegar and wiped with a cloth dampened with water. Subsequently, heat the oven for at least one hour at 150°C to facilitate cleaning. When the oven has cooled, wipe it again with a damp cloth.

13.11.2 Cleaning the oven door

We recommend always keeping the oven door clean. Use kitchen roll and on tougher dirt use a damp cloth and household detergent.

Spray products for cleaning the oven must not be used to clean the fan and the thermostat sensor inside the oven compartment.

13.12 Replacing the oven light bulb

Before carrying out maintenance, switch off the power supply to the appliance.

Proceed as follows:

• open the oven door;

• unscrew the glass safety cap anticlockwise; unscrew the bulb and

replace it with another one for high temperatures (300°C) with the following characteristics:

Voltage: 240 Vac / 50 Hz Power: 15 W Attachment: E 14

• Refit the glass cap and switch on the power. It is possible to check that the oven light is working even when the door is closed by turning the function switch knob to position .

Page 43

Instructions for the user

14. Special maintenance

Periodically, it is necessary to maintain or replace some parts that are subject to wear and tear. Specific instructions are given below for each type of maintenance.

Before carrying out maintenance, switch off the power supply to the appliance and close the gas tap.

14.1 Removing the oven door

The oven door can be completely removed to enable more thorough cleaning. Though this operation is possible, it should not be performed by everyone, as it requires the strength to hold up the door and a minimum of expertise to re-fit it. If you are not sure of being able to do this, we recommend that you clean the door without taking it off or, in special cases, that you contact the nearest authorised service centre.

To remove the door, proceed as follows:

• Open the oven door and release the safety catches of the hinges by turning the respective pins A (one for each hinge) backward.

• Partially close the door until there is no more load tension on the springs (the door will form an angle of about 30°).

• Using both hands, accompany the movement of the door towards closure and simultaneously lift it upward.

• Turn the lower part of the door towards the outside to free the hinges B from their seats.

If you need to remove any dry residues or dust deposited on the inner part of the windows, turn the door upside down as shown in the figure, slide a soft bottle brush into the spaces between the glass plates and brush gently.

To re-fit the door, carry out the instructions given above in the inverse direction. When the hinges B are back in their seats, open the door all the way and re-fit the safety catches of the hinges, lowering the respective pins A (one for each hinge).

CAUTION: After re-fitting the door, always be sure to re-fit the hinge safety catches.

Page 44

Instructions for the user

14.2 Removing the side rack-holder frames

The rack-holder frames can be removed to clean them separately and to facilitate cleaning the oven walls. The frames are hooked to the oven wall in the three points indicated by the arrows in the figure (detail 1).

• Press downward with your fingers as shown in detail 2 of the figure to release the frame from the upper pin.

• Lift the frame upward and take it out.

To re-fit proceed in the inverse direction. Set the lower part of the frame on the respective pins and press the upper part against the oven wall until it hooks onto the pin.

14.3 Removing and cleaning the inside oven fan

The inside fan of the ventilated oven may require periodic cleaning. To disassemble the fan proceed as follows:

• Make sure that the power supply to the appliance is switched off.

• Remove all inside components (dripping pan, shelves).

• Loosen and remove the four screws A from the cover panel.

• Remove the cover panel B.

• Use a coin to loosen the fixing nut C of the fan (this threading is inverse; to loosen turn

clockwise).

• Remove the fan D and wash it by immersing it in warm water and dish detergent. Never use abrasive or

corrosive detergents, powdered products, or metal scrubbers. Rinse the

fan and dry it thoroughly.

Re-fit the fan and the cover by working in the inverse direction to the instructions for removal.

14.4 Adjustment of the drawer height

The clips of height adjustment are located in the lower side and at the right and left ends of the drawer.

• By turning the lever A the drawer will raise of 3 mm.

Page 45

Notes

______________________________________________________________________

Page 46

Notes

______________________________________________________________________

Page 47

domestic warranty - full five year warranty

In addition to all statutory rights which you, the Consumer, have under the relevant laws in respect of this appliance, during the first five years of ownership as the original purchaser of this Kleenmaid appliance, we guarantee that any fault caused by faulty material or workmanship becoming apparent will be rectified free of charge for parts and labour, provided that all service is performed during normal working hours by Kleenmaid or their designated Agents. Where the appliance is installed outside the normal servicing area of the above, the Purchaser must pay for the cost of transporting the appliance to and from the Agent or the Agent’s travelling cost to and from the Purchaser’s home.

commercial warranty - one year warranty

When this appliance is installed in a commercial application, you, the Consumer, have under the relevant laws in respect of this appliance, during your first one year of ownership as the original purchaser of this Kleenmaid appliance, we guarantee that any fault caused by faulty material or workmanship becoming apparent, will be rectified free of charge for parts and labour, provided that all service is performed during normal working hours by Kleenmaid or their designated Agents. Where the appliance is installed outside the normal servicing area of the above, the Purchaser must pay for the cost of transporting the appliance to and from the Agent or the Agent’s travelling cost to and from the Purchaser’s home.

what these warranties do not cover

We are not responsible for any damage or malfunction unless caused by a defect in material or workmanship. This includes but is not limited to abuse, misuse, improper installation and transportation damage. We are not responsible for any consequential damages from any malfunction.

The Consumer must make the appliance available for servicing and shall bear any costs incurred for any de-installation and/or re-installation required to make the appliance available for servicing. Kleenmaid is not liable for any consequential damage incurred during de-installation or reinstallation.

warranty does not cover replacement of light globes or glass breakage due to impact

In case of fractured glass do not use your appliance.

warranty registration

Please complete warranty details below. Please retain together with your proof of purchase document. These documents will need to be viewed by our a member of our Service team should you request in warranty service.

service assistance

To assist you when phoning our Customer Ser vice number to arrange a service call please complete the following details and have them ready when you call.

Model Number _____________________________________ Date of Purchase _______________________________

Kleenmaid Store Purchased From ______________________ Date of Installation ______________________________

KLEENMAID CUSTOMER SERVICE - 1300 652 100

warranty

and service

Page 48

appliances available

in the Kleenmaid range

ZS3360 05/07

the best products we can find.

We search the globe for products that meet our high standards of functionality, style and quality and are proud of our innovative range sourced from countries throughout the world.

This outstanding appliance from our professional series is proudly handed crafted in Italy.

Washing Machines

Dryers

Dishwashers

Ovens

Cooktops

Outdoor Cooking Centres

Built-In Coffee Machines

Rangehoods

Freestanding Ovens and Cooktops

Sinks

Waste Disposals

Taps

Cookware Refrigerators Wine Cellars

Vacuum Cleaners

To find your nearest Kleenmaid Showroom

telephone 13 13 08.

B00090 ZS3360 12/07