Congratulations on the purchase of your new rangehood
appliance. This
has been designed and manufactured to give you years of reliable performance.
the kleenmaid story.
More than one million Australians enjoy using Kleenmaid appliances daily. Selected because of
their unique design, outstanding performance, excellent quality and unquestionable reliability,
each one is value-for-money, 100 per-cent guaranteed and at the top of its class.
attention to detail.
We are proud of our reputation for product innovation and service excellence. By dealing direct, we
can ensure that you consistently receive a high standard of customer service.
Free delivery, dedicated customer service and after-sales service team plus free kitchen design and
planning seminars are just a few of the ways we are setting new benchmarks for customer service
and experience.
satisfaction guaranteed.
Your new
appliance is covered by a written five-year parts and labour warranty,
guarantee, and a unique best value guarantee.
best results.
For best results, carefully read the enclosed instructions on how to install your new rangehood.
Correct installation will avoid delays and unnecessary service calls.
This booklet provides you with comprehensive information to help you get to know the controls and
the features of your new rangehood.
congratulations
rangehood
1
no lemon
Page 3
INSTRUCTION ON MOUNTING AND USE
7
6
1
8
5
3
2
4
1
f
j
g
g
i
2
4
c
b
a
g
g
h
3
2
Page 4
=
=
X
X
H
G
A
INSTRUCTION ON MOUNTING AND USE
20a
20a
H
20b
G
15
14
20b
C
2
B
19
7-16
11
11
18
9
8
12
13
8
B
9
17
8
9
4
6
5
10
1
1
3
5
5
3
Page 5
INSTRUCTION ON MOUNTING AND USE
GB
Consult the designs in the front pages referenced in the text
by alphabet letters. Closely follow the instructions setout in this manual. All responsibility, for any damages
or fires caused by not complying with the instructions in this
manual, are the responsibility of the user.
The Rangehood must be placed at a minimum distance of
50 cm from the cooking plane for electric cookers and 65cm
for gas cookers.
The Rangehood can be installed above these heights but for
optimum performance it should be installed at the distance
quoted for the appropriate heat source.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only.
The hood is equipped with a top air outlet B for discharge
of fumes to the outside (Ducting version – exhaust pipe
and pipe fixing clamps not provided).
Should it not be possible to discharge cooking fumes and
vapour to the outside, the hood can be used in the filterversion, fitting an activated carbon filter and the deflector F
on the support (bracket) G, fumes and vapours are recycled
through the top grille H by means of an exhaust pipe
connected to the top air outlet B and the connection ring
mounted on the deflector F (exhaust pipe and pipe fixing
clamps not provided).
The models with no suction motor only operate in ducting
mode, and must be connected to an external suction device
(not supplied).
Expansion wall plugs are provided to secure the hood to
most types of walls/ceilings. However, a qualified technician
must verify suitability of the materials in accordance with the
type of wall/ceiling. The wall/ceiling must be strong enough
to take the weight of the hood.
Do not tile, grout or silicone this appliance to the wall.
Surface mounting only.
Installation - Fig. 5
Preliminary information for installation of the hood
Assembling the chimney flue support/bracket (3
parts):
The 3 parts should be fixed with 4 screws, the support
extension is adjustable and should correspond to the internal
width of the telescopic chimney flue.
Disconnect the Rangehood during electrical connection, by
turning the home mains switch off.
Remove the 2 screws fitted inside the lower part of the
Rangehood at the points in which it is fixed to the suction unit
(see
also operation 3 - remove the grease filter/s).
1. Rest the suction unit on a flat surface and thread the lower
part of the Rangehood onto it.
2. Connect the sensor to the small plate on the front of the
suction group (A – the male and female connectors have
an obligatory access) and the lamps (C).
Connect the control panel to the small plate located on
the front of the suction group (B – the male and female
connectors have an obligatory access).
3. Fasten the Rangehood to the suction unit using 8 screws.
4. Using a pencil, draw a line on the wall, extending up to
the ceiling, to mark the centre. This will facilitate
installation.
5. Rest the drilling template against the wall: the vertical
centre line printed on the drilling template must correspond
to the centre line drawn on the wall, and the bottom edge
of the drilling template must correspond to the bottom
edge of the Rangehood: bear in mind that, when
installation is complete, the underside of the Rangehood
must be at least 50 cm above the cooker top in the case
of electric cookers, and at least 65 cm above the cooker
top in the case of gas or mixed cookers.
6. Rest the support bracket on the drilling template so that
it coincides with the dotted rectangle, mark the two outer
holes and drill them, remove the drilling template, insert
2 wall plugs and fix the Rangehood support bracket into
place using two 5x45mm screws.
7. Hang the Rangehood on the bracket.
8. Adjust the distance of the Rangehood from the wall.
9. Adjust the horizontal position of the Rangehood.
10. From inside the suction unit, use a pencil to mark the hole
to be used for final fixing of the Rangehood.
11. Remove the Rangehood from the bracket.
12. Drill at the point marked (Ø8mm - see operation 10).
13. Insert 1 wall plug
14. Rest the chimney support bracket G against the wall,
touching the ceiling. Use the support bracket as a drilling
template (the small slot formed on the support must
coincide with the line drawn on the wall as above –
operation 4) and mark 2 holes with a pencil, drill the holes
(Ø8mm), insert 2 wall plugs.
15. Fix the chimney support bracket to the wall using two
5x45mm screws.
16. Hook the Rangehood onto the bottom bracket.
17. Fix the Rangehood into its final position on the wall using
one 5x45mm screw (ABSOLUTELY ESSENTIAL).
18. Connect a pipe (pipe and pipe clamps not provided, to
be purchased separately) for discharge of fumes to the
connection ring located over the suction motor unit.
If the Rangehood is to be used in ducting version, the
other end of the pipe must be connected to a device
expelling the fumes to the outside. If the Rangehood is
to be used in filter version, fix deflector F to the chimney
support bracket G using 4 screws, and connect the other
end of the pipe to the connection ring on deflector F.
Make the electrical connections.
19.
20. Apply the chimney stacks and fasten them at the top tothe chimney support G (20b) using 2 screws (20a).
4
Page 6
GB
INSTRUCTION ON MOUNTING AND USE
21. Slide the bottom section of the chimney down until it
completely covers the suction unit and slots into the
housing provided on top of the Rangehood.
22. Turn the mains power on again at the central electrical
panel and check for correct Rangehood operation.
Carry out the SET-UP of the control panel, if necessary.
To do this consult the ‘Functioning – SET UP’ paragraph
in the following pages.
Electrical connection
The electrical tension must correspond to the tension noted
on the label placed inside the Rangehood. Connect the
electrical plug, where provided, to an easily accessible
outlet in conformity with Australian Standards.
Where an electrical plug is not provided (for direct connection
to electrical network) place a standards approved bipolar
switch with an aperture distance of not less than 3mm
(accessible) from the contacts.
Description of the Rangehood - Fig. 1
1. Control panel
2. Grease filter
3. Grease filter release handle
4. Halogen lamp
5. Vapour screen
6. Telescopic chimney
7. Air outlet (used for filter version only)
8. Sensor
Operation –
Model with electronic controls
123 4 567
Main Functions
1 - ON-OFF lamp button
2 - LED signal for anti-grease filter saturation (See the
relative cleaning instructions for anti-grease filters).
3 - Led signal for active carbon filter saturation (See the
relative cleaning instructions for active carbon filters).
4 - LED signal for “automatic” operation
5 - ON-OFF button for “automatic” operation
6 –Functions signal (LED Display).
7 - ON/OFF Knob and suction power selection.
List of Functions
To switch the Rangehood to (ON) depress knob 7
The operation of button 5 is enabled and the wording
“Sensor” will appear, the Rangehood will set at “Manual
Stand-By”.
To switch the Rangehood to (OFF) press button 7 again;
if the Rangehood is set in the “automatic” operation
mode then pressing button 7 once will launch the
Rangehood to “manual Stand-By” pressing the button
again will switch the Rangehood to (OFF).
Attention! When the Rangehood is switched (OFF) all the
functions are disabled.
To switch on the lamps press button 1.
To switch off the lamps press button 1 again.
To increase the suction speed rotate button 7 clockwise
and set the desired speed (1, 2, 3 or intensive).
Attention
The intensive suction speed is timed for 5 minutes after
which the Rangehood returns to the 2
The LED number (1, 2 or 3) will appear on the Display,
which is equivalent to the suction speed set plus a red
LED will also appear when the suction speed is set at
intensive.
The other display led’s will turn on alternatively in
proportion to the suction power setting.
To decrease the suction speed rotate the button
anticlockwise (Intensive, 3, 2, 1, Stand-by)
Filter Saturation Signal
The Rangehood is provided with an electronic device
which signals the necessity to clean and/or replace the
filters (Grease or Active Carbon).
Attention!
The saturation signal device for the active carbon
filter is disabled, the enabling (or disabling) function is
performed in the SET-UP operation (see instructions at
the bottom of the page).
Grease filter saturation signal
The LED signal 2 will turn on.
Active Carbon filter saturation signal
The LED signal 3 will turn on.
Attention! The signal will not appear when the Rangehood
is switched (OFF) or in stand-by mode.
Reset the Filter saturation signal (to be carried out ONLY
after having cleaned and/or replaced the filters):
Set the Rangehood to stand-by press button 7 until the
sound of the beep and upon the turning off of the wording
sensor.
Automatic Operation
The Rangehood always sets at “manual operation”,
by pressing button 5 the Rangehood sets to “automaticoperation”: the wording Sensor turns on (from white
to orange); the Rangehood starts up and regulates the
speed only if the sensors detect any variations in the
environment conditions. The LED signals for function 6
will turn on in sequence at a speed that varies the suction
speed that it sets automatically on the basis of the
sensors readings.
nd
speed.
5
Page 7
GBINSTRUCTION ON MOUNTING AND USE
Pressing button 5 again and rotating button 7 the
Rangehood returns to “manual operation”.
Attention! The sensors automatically calibrate every
half hour, and on the basis of the data detected will
determine the automatic turning on or off of the
Rangehood.
In certain cases (where the environment temperature
increases or decreases for other reasons) it may be
necessary to carry out a manual calibration for the
sensor.
The manual calibration of the sensor may be performed
in the SET-UP operation.
Safety
When the Rangehood is in manual stand-by mode and
the sensors detect an excessive increase in the
temperature, the Rangehood will set to “automaticoperation” and if the environment conditions require it,
then the motor will also start up.
h
g
f
a
b
c
d
e
SET-UP
To access the set-up mode
•Press button 7 and switch the Rangehood to (OFF- all
the led’s are turned off).
•Keep button 5 pressed and press button 7.
To exit the SET-UP mode
•Press button 7 again.
To enable the saturation device for the active carbon
filter
Upon entering the SET-UP mode, turn button 7 clockwise
until the LED (e) turns on. If the LED is red, press button
5 once, the LED (e) will turn green which will indicate
that the saturation signal device has been enabled for
active carbon filter, press again to disable (LED (e) will
turn red).
To carry out manual calibration
Upon entering the SET-UP mode, turn button 7 clockwise
for one click (about 10°) until the LED (c) turns on (red
LED).
Press button 7 to carry out manual calibration.
Additional information:
When rotating the knob clockwise in SET-UP mode, if
the LED (g) turns on then ignore it.
If the Rangehood fails to operate correctly, briefly disconnect
it from the mains power supply for almost 5 sec. by pulling
out the plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the Rangehood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
6
Page 8
GB
INSTRUCTION ON MOUNTING AND USE
Maintenance
Prior to any maintenance operation ensure that the Rangehood
is disconnected from the power supply.
Cleaning
The Rangehood should be cleaned regularly internally and
externally.
For cleaning use a cloth moistened with denatured alcohol
or neutral liquid detergents. Avoid abrasive detergents.
Warning:
Failure to carry out the basic standards of the cleaning of the
Rangehood and replacement of the filters may cause fire
risks.
Therefore we recommend observing these instructions.
Grease filter
This must be cleaned once a month using non abrasive
detergents, either by hand or in the dishwasher, which must
be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may
discolour slightly, but this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle
(f) - (Fig. 2).
Caution
The appliance is not intended for use by young children or
infirm persons without supervision.
Young children should be supervised to ensure that they do
not play with the appliance.
Do not use the Rangehood where the grill is not correctly
fixed! The suctioned air must not be conveyed in the same
channel used for fumes discharged by appliances powered
by other than electricity. The environment must always be
adequately aerated when the Rangehood and other appliances
powered by other than electricity are used at the same time.
Flambé cooking with a Rangehood is prohibited. The use
of a free flame is damaging to the filters and may cause fire
accidents, therefore free flame cooking must be avoided.
Frying of foods must be kept under close control in order to
avoid overheated oil catching fire. Carry out fumes
discharging in accordance with the regulations in force by
local laws for safety and technical restrictions.
Charcoal filter (filter version only)
This absorbs unpleasant odours caused by cooking.
The charcoal filter can be washed once every two months
using hot water and a suitable detergent, or in a dishwasher
at 65°C (if the dishwasher is used, select the full cycle
function and leave dishes out).
Eliminate excess water without damaging the filter, then
remove the mattress located inside the plastic frame and put
it in the oven for 10 minutes at 100° C to dry completely.
Replace the mattress every 3 years and when the cloth is
damaged.
Remove the filter holder frame by turning the knobs (g) 90°
that affix the chimney to the Rangehood (Fig. 3).
Insert the pad (i) of activated carbon into the frame (h) and
fit the whole back into its housing (j).
Replacing lamps - Fig. 4
Access the light compartment
press on the lamp cover and release to open.
Warning!
Prior to touching the light bulbs ensure they are cooled down.
Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure you
do not touch them with your hands.
Close the lamp cover (it will snap shut).
If the lights do not work, make sure that the lamps are
fitted properly into their housings before you call for
technical assistance.
7
Page 9
warranty
and service
domestic warranty - full five year warranty
In addition to all statutor y rights which you, the Consumer, have under the relevant laws in respect of this appliance,
during the first five years of ownership as the original purchaser of this Kleenmaid appliance, we guarantee that any
fault caused by faulty material or workmanship becoming apparent will be rectified free of charge for parts and labour,
provided that all service is performed during normal working hours by Kleenmaid or their designated Agents. Where
the appliance is installed outside the normal servicing area of the above, the Purchaser must pay for the cost of
transporting the appliance to and from the Agent or the Agent’s travelling cost to and from the Purchaser’s home.
commercial warranty - one year warranty
When this appliance is installed in a commercial application, you, the Consumer, have under the relevant laws in
respect of this appliance, during your first one year of ownership as the original purchaser of this Kleenmaid appliance,
we guarantee that any fault caused by faulty material or workmanship becoming apparent, will be rectified free of
charge for parts and labour, provided that all service is performed during normal working hours by Kleenmaid or their
designated Agents. Where the appliance is installed outside the normal servicing area of the above, the Purchaser
must pay for the cost of transporting the appliance to and from the Agent or the Agent’s travelling cost to and from
the Purchaser’s home.
what these warranties do not cover
We are not responsible for any damage or malfunction unless caused by a defect in material or workmanship. This
includes but is not limited to abuse, misuse, improper installation and transportation damage. We are not responsible
for any consequential damages from any malfunction.
The Consumer must make the appliance available for ser vicing and shall bear any costs incurred for any
de-installation and/or re-installation required to make the appliance available for servicing. Kleenmaid is not liable for
any consequential damage incurred during de-installation or reinstallation.
warranty does not cover replacement of light globes or glass breakage due
to impact
In case of fractured glass do not use your appliance.
warranty registration
Please complete warranty details below. Please retain together with your proof of purchase document. These
documents will need to be viewed by our a member of our Service team should you request in warranty service.
service assistance
To assist you when phoning our Customer Service number to arrange a service call please complete
the following details and have them ready when you call.
Model Number _____________________________________ Date of Purchase _______________________________
Kleenmaid Store Purchased From ______________________ Date of Installation ______________________________
KLEENMAID CUSTOMER SERVICE - 1300 652 100
8
Page 10
appliances available
in the Kleenmaid range
the best products we can find.
We search the globe for products that meet our high standards of functionality, style and quality and
are proud of our innovative range sourced from countries throughout the world.
Washing Machines
Dryers
Dishwashers
Ovens
Cooktops
Outdoor Cooking Centres
Built-In Coffee Machines
Rangehoods
Freestanding Ovens and Cooktops
Sinks
Waste Disposals
Taps
Cookware
Refrigerators
Wine Cellars
Vacuum Cleaners
To find your nearest Kleenmaid Showroom
telephone 13 13 08.
9
Page 11
10
Page 12
11 LI2X3A
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.