Klearbar COUNTERTOP WATER DISPENSER User Manual
KLEARBAR MINI COUNTERTOP WATER DISPENSER
INSTALLATION / USER MANUAL
Dear customer,
We know you have multiple
options and thank you for
choosing the best.
KlearBar - For home and oce.
Clearly the right call anytime.
Index
Overview & diagram 06
Installation 07
User Maintenance 12
Safety Instructions 17
Technical specications 18
Troubleshooting 20
WHAT’S YOUR
FAVORITE COLOR?
Blue bar
Red bar Green bar Yellow bar
Orange bar
Silver bar
Cream barWhite bar Black bar
06
1
Overview & Diagram
1. Touchscreen operation panel
2
2. Front panel indicator light:
Blue - COLD water
3
Red - HOT water
Purple - ENERGY SAVE mode
(Energy save mode will start after
4 hours of non-use. Touch any key
to bring system to normal operation)
3. Faucet
4
4. Removable drip tray
5
5. Removable top panel
6. On/O cold water compressor and
6
delivery pump
7
7. On/O hot water tank
8. Water overow line outlet
9. Water line inlet (insert included
1/4 stem)
8
9
Touch screen instructions / user guide
1
1. Hot water activation icon
2
2. Tank rell activation icon
3
3. Cold water activation icon
4
4. UV light activation icon (Mini2 only)
For HOT water dispense touch and
release #5, then touch and hold #6
6 75
For COLD water dispense touch and hold #
7
Installation & Maintenance
07
Your Klearbar Mini comes standard with virtually everything you need for a simple
water line connection:
• Installation/User manual
• 15 feet of food grade, 1/4 polyethylene tubing
• 45 psi pressure reducer (pre-installed inside water dispenser)
• Angle stop valve (mains connector)
• 1/4 union tee (install if using existing ice maker water line connection)
• 1/4 stem elbow (install at water line inlet)
You may also need the following items to assist your installation:
• Adjustable wrench to install angle stop valve
• Teon plumbers tape (use when installing angle stop valve)
• Plastic tubing cutter or scissors
• 3/8 inch drill bit and drill (if needed to drill hole in cabinetry to hide water line)
ALWAYS PLUG KLEARBAR MINI ELECTRICAL CORD INTO A GFCI PROTECTED POWER OUTLET
There are multiple ways to connect your Klearbar Mini but regardless of your choice it
is recommended to follow local plumbing codes or consider hiring a licensed plumber.
But should you decide to DIY (do it yourself) we have provided a basic blueprint to get
you on your way.
Perhaps the easiest connection is to an existing water line already provided by your
refrigerator ice maker. Use a 1/4 union tee for this connection.
Connect 1/4 tubing into 1/4 stem elbow.
Connect 1/4 stem elbow into water line inlet port
Connect 1/4 tubing into 1/4 union tee inserted into
refrigerator water feed line
1/4 stem elbow1/4 union tee
08
Connect To Existing Refrigerator Ice Maker Water Line
- use the included 1/4 union tee when connectingto a 1/4
water mains connection or, use a brass compression
union tee if desired (always use a plastic compression
ferrule when connecting polyethylene
union - a brass compression ferrule may
tubing using a brass
cut into the plastic
tubing and cause a leak).
1.
BEFORE PLUGGING IN TO ELECTRICITY turn o water line supply to refrigerator
ice maker.
2.
Using a plastic tube or copper line cutter, make a square cut of the existing ice maker
water line no closer than 12 inches from where the water line originates from the oor
or wall, and insert the
1/4
union tee here. It may be good to have a large towel nearby as
a small amount of residual water may spray and drain out once the line is cut . Connect
one end of the included
3.
Place the Klearbar Mini within a few feet of an available GFCI electrical socket and
connect the included
1/4
polyethylene tubing to the
1/4
stem elbow into the water inlet port on the back of the unit
1/4
union tee.
(be careful not to connect to the optional overow port). Now connect the opposite
end
1/4
polyethylene water line into the
1/4
elbow behind the Klearbar Mini. Trim o
extra water line as needed for a professional look.
Remove moisture absorbing
desiccant bag
Desiccant bag removed
(1 piece)
Loading...