KKDC SEN CV 035 Installation Manual
SEN CV 035
High Power
PRODUCT CARE AND HANDLING
• KKDC products are delivered in appropriate packaging. Any handling instructions on the packaging must be observed. Products
should remain in packaging ‘as delivered’ until installation or for ongoing transportation and storage.
• Inspect products carefully before installation. Do not proceed to install any product that may have been damaged in transportation,
storage or handling.
• Handle with care. Many KKDC products contain precision electrical components and are not designed to withstand excessive
stresses from tension or compression.
• Please follow standard ESD (Electrostatic discharge) protection measures when handling and installing KKDC LED products.
SAFETY AND WARRANTY
• Installation is only to be carried out by suitably qualied persons in accordance with installation instructions and all applicable
regulations or standards. (Improper installation can create an electrical hazard with risk of electric shock, re or injury).
• KKDC will not be held responsible for any consequences arising from improper product handling, storage or installation.
• KKDC products must be installed as supplied. Disassembly, modication or attempted repair will invalidate warranty and may create
an electrical hazard.
• The KKDC product warranty is available with this document or on our website – www.kkdc.lighting.
PR EPARATIO N
Installation Guide
• Install KKDC products in accordance with the Wiring and Mounting instructions supplied with the product, using the
recommended accessories, tools and xings where specied.
• Product specication and installation information is also available from the KKDC website www.kkdc.lighting.
• Products should only be installed in areas appropriate to their IP rating, operable temperature and humidity range.
• Carefully plan and check the physical layout and circuit structure of the installation before starting work. Note wiring methods,
cable type and connection points along with positioning and rating of power supplies and any control gear. Refer to all product
information – including that for power supplies/control gear – and conrm choice of power supply, control gear, cable thickness
and cable length.
• For safe and reliable operation KKDC LED products must only be used with suitable KKDC supplied or recommended power
supplies and control gear. Contact KKDC for further information.
(North America – Use only UL listed Class 2 power supplies with KKDC products – See also Installation Guide – Wiring)
• The KKDC LED products in this guide require 12V DC or 24V DC ‘constant voltage’ power supplies as indicated in product
specications.
AFTER INSTALLATION
• KKDC products are designed to be maintenance free however accumulated dust may be removed from the emitting surface of
luminaires with careful use of a soft dry cloth.
• Ensure that paints, organic solvents and caustic or corrosive cleaning chemicals do not come into contact with KKDC products.
For example DO NOT USE –
- Benzene, Toluene, Xylene, Acetone, Carbon tetrachloride, Gasoline, Ether,
- Sodium/Calcium hydroxide, Sodium Carbonate.
• For cleaning or sanitization – products in sealed IP rated housings may be wiped with a soft cloth dampened with an alcohol
cleaner or with cool, soft water diluted (5% or less) bleach (Sodium Hypochlorite) solution.
• Please retain this information and pass to those responsible for installation/site maintenance.
Note: KKDC may change product specications and installation guidance without prior notice.
See KKDC website for product document updates. www.kkdc.lighting SENCV035IG-02.01EN-20190611
SEN CV 035
High Power
READ BEFORE INSTALLATION
• The mounting surface to which any KKDC product is attached must not carry any electrical potential and metallic surfaces must be
earthed. Avoid physical contact between adjacent LED products.
• Prepare, measure and mark the installation location and mounting surfaces before xing. Any machining or drilling etc. should be
completed before mounting. KKDC products and their immediate installation area should be kept clean, dry and free of paints and
solvents during and after installation.
• Ensure that products are mounted with supplied, recommended or appropriate screws and xings to suit the surface material.
• Mount products so that cables and connectors will not come under excessive stress and position accessories, wiring and
connectors where they will not cast shadows.
• UL listing for US only – 100W max., 700mA mix. See wiring guides for maximum installation lengths.
MOUNTING – LOW ADJUSTABLE BRACKET
Installation Guide – Mounting
1 2 3
Secure brackets with hex key.
Mark and drill holes for screws.
MOUNTING – ADJUSTABLE BRACKET
Fix with suitable screws. Adjust to required angle and secure
1 2 3
Secure brackets with hex key.
Mark and drill holes for screws.
Fix with suitable screws. Adjust to required angle and secure
with hex key.
with hex key.
Note: This guide is produced from testing under ‘average’ conditions and does not represent all possible applications or installation circumstances.
Please contact KKDC for further information.
KKDC may change product specications and installation guidance without prior notice.
See KKDC website for product document updates. www.kkdc.lighting SENCV035MG-02.01EN-20190726
SEN CV 035
High Power
MOUNTING – LOCK CLIP
Installation Guide – Mounting
1 2 3
Fix clips with suitable screws.
(min 3 clips per metre or every
500mm/20”).
MOUNTING – MOUNTING PLATE
Open clips and press in position.
Ensure clip is closed over tting.
1
Check product/plate orientation
and cable grommet clearance from
mounting surface. Mark position
of plates (supplied with the preinstalled sliders – 2 per metre).
MOUNTING – FIXED BRACKET
2
Position slider over plates (lock slider
with grub screw/hex key).
3
Secure slider to plate with hex key.
1 2 3
Secure brackets with hex key.
Mark and drill holes for screws.
Note: This guide is produced from testing under ‘average’ conditions and does not represent all possible applications or installation circumstances.
Please contact KKDC for further information.
KKDC may change product specications and installation guidance without prior notice.
Fix with suitable screws.
See KKDC website for product document updates. www.kkdc.lighting SENCV035MG-02.01EN-20190726
Loading...