K jump Health TEMPONITOR User Manual

Clinic Patch Thermometer

(Temponitor)

USER INSTRUCTION

Model KD-2100

C

15:38

TIME

37.0

Manufacturer :

K-Jump Health Co., Ltd.
No. 56 Wu Kung 5 Rd.,
Wu Ku Industrial Park,
Taipei Hsien, Taiwan 248

th

Contents Precaution About the Device (2)

Contents...............................................1

Precaution............................................2

About the device....................................2

Battery installation/replacement.............3

Setting the device..................................4

Preparation before measurement............5

Important information.............................6

Start measurement.................................7

Memory reading.....................................8

Using the flash light................................8

Turn off the device..................................8

Maintenance..........................................9

Error message......................................10

Specification........................................ 11

Intended for Use

This device is intended to be used to
monitor the body temperature by applying
the temperature patch to body skin or
axillary.

Notice

1. Use of this thermometer is not to be a
substitute for consulting with a physician.

2. Person with pacemaker implemented

should consult the doctor before using
this device.

3. Intensive supervision is necessary when
using this device on infant, children and
compromised person.

This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1)this device may
not cause harmful interference, and (2)this
device must accept any interference
received, including interference that may
cause undesired operation.

1

FCC Interference Statement

FCC ID : RYZTEMPONITOR

This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference with not occur in a
particular installation. If this equipment does not
cause harmful interference to radio or TV
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:

- Reorient or relocated the receiving antenna.

- Increase the separation between the equipment
and receiver.

- Connect the equipment into and outlet on a
circuit different from that to which the receiver is
connected.

- Consult the dealer or an experienced radio/TV
technician for help.

Caution: To assure continued FCC compliance

Any changes or modifications not expressly
approved by the grantee of this device could be
void the user's authority to operate the device.

About the Device (1)

The Patch

KD-PT01
Under Arm Patch

Temperature

KD-PT02
Body Skin Patch

Transmission PartTransmission Part

Sensor

Transmission Part

Temperature Sensor

2

KD-PT03
Ear Plug Patch

KD-2101 Temperature Reader

C

15:38

Memory Key

Start Key

Light Key

TIME

37.0

The LCD

Date/Time

DATE

(M/D)

TIME

Temperature

Battery installation / replacement

1. Remove battery
cover by pulling the
battery cover.

2. Install/replace four
new 1.5 V Size- AAA
batteries into the

battery compartment.

Note that be sure the
batteries should
have the correct
polarity.

3. Close the battery
cover.

3

Temperature Sensor

Transmission Part

LCD Display

On/Off Key

Memory

MEMORY

Temperature
Unit

Low Battery

Light

Setting the Device

Preparation before Measurement

Important Information Start Measurement

Setting Date and Time

After installation/replacement of the
batteries, the date and time are re-freshed
to default value; a setting is necessary by
following steps:

1. Under power-off mode,

M key

keep pressing the "M"
key until it shows a
flashing "2003" which is
the setting mode of year.

2. Every clicking of the "M"
key to enter the next
mode said month date

DATE

(M/D)

DATE

(M/D)

hour minute to the

end.

3. Every clicking of the of
"O/I" key will add one to
the value for your setting.

4. After the setting, the

TIME

TIME

O/I key

O/I key
(+ 1)

(+ 1)

device is always back to
"power-off" mode.

Setting °C or °F

The KD 2101 provides user to select the unit
in either °C or °F by following steps:

1. Click the "O/I" key to turn on the device.

2. The LCD will show all

TIME

segments first and
enter to default unit
mode; now, you have
5-second period for

(Keep pressing
O/I key for 2 sec)

the setting; keep
pressing the O/I key
and the unit will
switch to either °C or

TIME

°F you want.

4

About the sensor

The sensors is constructed by two parts:
transmitter and temperature sensor. The
transmitter is used for inducing power as
well as data transmission; the temperature
sensor is used for body temperature
detecting.

Applying the Sensor

For fixing the sensor, a dressing (or surgical)
adhesive tape will be needed. A high quality
tape without side-effect is recommended
since long period (usually 24~48 hr)
adhesion.

1. Apply the sensor to ear canal, armpit or
abdominal area below navel(depended
on different types).

2. For armpit and body skin, fixing the
sensor by medical adhesive tape(s). Be
sure the firmness.

3. Subject is allowed to dress cloth rather
than naked.

4. For infant or baby, the patch under diaper
will benefit the measurement result since
warmer measurement environment.

Insert the ear
tape patch
into ear
canal.

Adhesive tape

sensor

Adhesive
tape

sensor

5

Period for Heat Equilibrium

After applying the sensor, a 5~10 minutes
waiting for temperature equilibrium
between the sensor and your skin surface
will be necessary before taking the first
measurement.

Skin surface
temperature

Room
temperature

5~10 min.

Start data reading

Room Temperature Affects Skin
Temperature

Skin is major organ for maintenance of body
temperature; either hot or cold environment
will cause skin temperature to rise or to fall.
It is recommended that subject is kept in a
comfortable room temperature (usually
22~28°C (71.6~82.4 °F) for taking the
measurement.

Notice

When using the skin sensor or armpit
sensor, wipe body skin with a dry towel .

6

1. Turn on the device, the device will
perform system checking automatically
until "ready for detecting" as figure:

TIME TIME

2. Place the reader on the upright direction
of the transmitter around 3~4 cm (1,5
inches) distance.

w

i

th

in

(1

3cm

.

5inch)

Start
key

3. Click the "start key", the device starts
scanning the patch temperature with
flashing "---".

TIME TIME

4. The result is then shown on the LCD with
2 beep sounds. Measurement is
completed.

TIME TIME

5. For another reading, just repeat the steps
mentioned above.

7