KJB GPS902-4G User Manual

1

What’s Inside

 iTrail GPS Device
 iTrail Charger
 iTrail Serial Number
 iTrail IME#
 iTrail Subscription Plan (Separate but Required)
 iTrail GPS App (Download free from the iOS App Store or Google Play Store)

 iTrail GPS Web Platform (http://track.myitrail.com)

Getting Started

With your iTrail Convoy purchase, an activation fee was included in your purchase price.
Please go to http://myitrail.com and click on “Activate Device” to sign up for a Billing
account and select a Data Subscription Plan that will fit your needs.

For this process, you will be signing up for two separate accounts: one for Billing and one
for the Live Tracking platform. You will therefore receive two separate email
confirmations: one will be a confirmation email stating you have created a Billing account,
or that you have added a data plan to your existing account. The second email will contain
your Tracking account credentials. Your Tracking account is created for you by our iTrail
Support Team.

Note: It may take 24-48 hours for your Activation and the two accounts to be created.

2

3

Device Installation

The iTrail Convoy is similar to that of a car stereo. If you are not confident in y our ability
to install the device, we suggest that you take this device to a mechanic who is familiar
with installing these types of devices or car stereos. They will need to make sure that it is
wired correctly according to the diagram located above.

The iTrail Convoy is powered by your vehicle; to install the device, connect the wiring

harness to the base unit as indicated in the diagram below. Once that’s done, connect the
Red wire to the vehicle’s power. Connect the Black wire to Ground. Connect the White
wire to the vehicle’s ignition or accessory power.

The iTrail Convoy features an internal antenna which is needed to ensure GPS
communication. When installing the unit in the dash of the vehicle, place the unit with
the lights and logo facing down with as little metallic obstruction above it as possible.
Because of differences in vehicle manufacturers, best placement will vary by vehicle. If
signal strength seems to be weak, move the device to a different position and check the
platform to see if the device has connected and is reporting.

Once the unit has been installed, take the car for a drive for 15-20 minutes so the device
can register on the GPS network and begin reporting. The iTrail Convoy is motion
activated; it will only attempt to communicate with the platform when motion is
detected, which will update the tracker’s position on the map.

The Red and Green LEDs on the label side of the device are intended to help you

troubleshoot problems with your tracker. When the car’s ignition is first turned on, the

device will power up. The GPS Light (RED) should begin to flash followed by the Cell Light
(GREEN). The GPS Light will turn solid once a GPS signal is located. The Cell Light will slow
down, but remain flashing once it has connected to the cellular network.

Navigating iTrail Live

To log into your iTrail Live tracking account, open a browser window and go to

http://track.myitrail.com. Enter your Username and Password provided to you, and click on

4

Login. We strongly suggest you change your Password, as this default Password is not unique
to your account. See page 20 for details.

The iTrail Live website is divided into 5 tabs: Dashboard, Tracking, Routing, Geofence, and
Reports. You can find these tabs at the top of the website.

Dashboard

Your Group Name is along the left-hand side of the Dashboard, showing how many GPS
trackers are registered under that Group.

 The Summary allows a user to easily see how their trackers are doing, how many

alerts were sent, how many devices were in idle status, how many registered
movement, and how many were stopped.

 You are also able to see the Average Idle Time, Average Max. Speeds, and most

recent Alerts Triggered in corresponding cells on the Dashboard.

5

 In the upper right-hand corner of the Dashboard, you can see your account name,

along with a few icons.

o Alerts: the bell icon is for alerts, and will have a red dot when there are

unviewed alerts triggered.

o Messages: the envelope icon is for the Messaging Center, which can be used to

send an email for iTrail Support.

o Gear: the Gear icon is for Favorites and Commands.
o Account Name: clicking on your Account Name will allow you to log out or

change your password.

Alerts: The Alerts section lets you manage what kinds of alerts your device will create and

how you will be notified.

1. Click on Setup Alerts under your Vehicle or Asset to get the following selection:

2. Click the Excessive Speed Selection on the “Select a Trigger” portion of the screen, for

example. This will then change the setup values on the remaining tabs, which lets you
choose when and where alerts will be sent. Select the device you would like to edit by
checking the box next to it. *Please note that you will need to select the device you

6