
1. Name and Parts
10
9
8
6
7
1. Power Button
2. Status Bar
3. Analog Cam In
4. Digital Cam In
5. Controller Port
6. Infrared Sensor
7. Reset Button
8. Memory Card Slot
2. Package Content
Battery Pack
Memory Card
Infrared Remote
Controller
A/V In Cable
5V12A Charger
European Standard
Adapter Head
12
11
13
14
Lock Rec
15
16
CAM IN
DIGITAL CAM IN
1 2
3
4
Stop
3. Charging Battery
2
10
CAM INDIGITAL CAM IN
1. Connect the charger plug to DC In Jack .
2. Plug power cord of the charger to an AC wall outlet. Charging starts automatically.
3. The LED bar will illuminate red to show the device is in charging mode.
Charging time required is 3 to 4 hours.
2
10
4. After charging is completed, red light turns off automatically.
5
4. Connecting Camera
Lock Rec
15
1
Stop
3
CAM IN
4
DIGITAL CAM IN
1
15
9. Battery Lock
10. DC In Jack
11. USB Port
12. A/V Out Port
A/V Out Cable
Cable Controller
HDMI Wired Controller
ON
OFF
REC
13. 3 Inch LCD Display
14. Screen Lock Button
15. Record/Stop Button
16. Battery Pack
USB Cable
Pouch
Stylus Pick
Earphone
1. Power on the DVR by pressing .
2. To connect an analogue camera, plug the analogue camera jack into CAM IN port
on the device
3. To connect a digital camera, plug digital camera jack into DIGITAL CAM IN port
on the device.
3. Switch REC/STOP to start / stop recording.
4. Various recording modes are optional on settings menu page.
5. Installing and Removing Battery
NOTE: PV-500EVO2 has a removable battery. You can purchase extra
batteries depending on your application. Following the instructions indicated
below to remove/replace battery.
1
1. T
o remove the battery, gently push LOCK switch to right
side and push battery in the direction of the red arrow.
2
1
LOCK
3
1
LOCK
2. To install the battery, attach the battery to the DVR
and gently push the battery in the direction of the red
arrow.
3. Slide the LOCK switch in direction of the red arrow to
lock the battery onto device.
6. Activating Screen Lock
Lock
A/V Out
3
4
1.Press the Lock button once. A lock icon appears on the screen.
This indicates screen lock is activated to avoid accidental screen operation.
2.Press the Lock button again. The lock icon disappears from the screen.
This indicates screen lock is deactivated.
Rec Stop
7. Wired Controller
Reset
1.Plug the HDMI Cable into control port in the direction of the red
arrow to connect the wired controller.
2.Long press ON/OFF button . Blue LED on the controller automatically lights up
to indicate that control device is powered on.
NOTE: PV-500EVO2 automatically defaults to Pre-event status when using the wired
controller to power up the device.
3.To start recording, long press REC button . Red LED signal on the controller
illuminates to show the DVR is recording.
NOTE: If PV-500EVO2 is under Pre-event status, the device records video 30 seconds
before video recording is activated.
4.To take a snap-shot during recording, press button on the side of the
controller. The image file is automatically saved on the memory card.
5.To end recording, press REC button again. To turn off the controller,
press ON/OFF button again.
NOTE: To activate recording, push the REC/STOP switch to the REC position first.
Main device and controller automatically accesses recording status
after main device or controller is turned on.
Control
2
3
1
232
1
4
5
4
5
1
22
(1) (3)(2) (4)
8. Connecting Computer and Monitor
Stop
Earphone
Lock Rec
Audio Out (L)
Audio Out (R)
Video Out
Connect to Computer
1.Flip up USB port cover. You will see one USB 2.0 port and one A/V Out port.
2.Insert the USB Cable into the USB port to connect a computer to the device.
3.Insert A/V Out Cable into the A/V out port to connect a monitor to the device.
NOTE: You can also insert earphones into AV-Out port for listening to recordings.
9. Retrieving Video Footage
1. Video files are stored on the memory card.
2. There are two methods to retrieve video files.
(1) Using a USB Cable to connect to a computer.
(2) Using a card reader to retrieve files from the memory card.
3. The computer detects the storage and user may browse and
operate the storage as a typical folder directory.
i.e.Rename, copy and paste, delete, duplicate, etc.
10. Edit Settings by IR Controller or Touch Screen
MAIN MENU
IMAGE
VIDEO
RECORD SETTING
1. Connect a video camera to the DVR and insert the memory card.
2. Turn on the DVR before using the IR remote controller.
Aim the IR Remote Controller at the sensor area to control the device remotely.
3.
2
4. Press Rec on the IR remote to start recording and press to stop .
5. Press again to return to Main Menu page.
1
3
1
6. Entering Recorder Setting to turn on Motion Detect.
5
7. Entering Program Setting to edit setting.
1
8. To turn off DVR, press the Power button .
9. Operating the touch screen interface to edit settings
Note that the power button on the IR remote controller only serves to turn off the
DVR. It is not possible to power up the DVR using the IR remote controller.
4
1
IR Remote Controller
1
1
5
1
2
1
3
1
3
1
4
1
1
1
.
(6) (7)(5)
REC
11. PV-500EVO2 Connection Illustration
Connect to Computer
Audio Out (R)
Audio Out (L)
Video Out
Earphone
DC 5V Power Adapter
Stop
Lock Rec
CAM INDIGITAL CAM IN
SD Card
Infrared Remote Controller
Microphone
350/450/550 TV Line Camera
Video In
Connect to other brands
Audio In
of camera
Microphone
Controller (REC, On/OFF, Photo Buttons)
DVR506
Portable Digital Video Recorder
Quick Guide
Camera
Law Enforcement Products Manufacturer
®
LawMate
V1.0