KJB CPM700 User Manual

CPM-700

COUNTERSURVEILLANCE PROBE/MONITOR

*

*

CPM-700 is available with several optional probes and accessories; some of which are
pictured above. This manual addresses available probes and accessories with the CPM-700,
however these probes and accessories are not necessarily included with each CPM-700.

PRECAUTION / WARNING!

The overall effectiveness of this product is directly dependent on your familiarization and level

of threat. This manual is marked * in areas where special attention is required.

RESEARCH ELECTRONICS INTERNATIONAL

455 Security Place

Algood, TN 38506 U.S.A.

[phone]

http://www.reiusa.net/

Revision 2

© COPYRIGHT RESEARCH ELECTRONICS INTERNATIONAL

This manual contains proprietary information intended

solely for use with the CPM-700 and CPM-700 Probes and Accessories.

All information contained within this manual

is subject to change without notice.

OWNER’S RECORD

The Serial Number of your unit is located on the side panel. Please record
this number and refer to it whenever you contact your dealer or Research
Electronics International concerning this product. Note: Removal or
alteration of the serial number automatically voids all warranties of this
product.

MODEL: CPM-700

SERIAL NUMBER: __________________

RESEARCH ELECTRONICS INTERNATIONAL

455 Security Place

Algood, TN 38506 U.S.A.

[phone]

www.reiusa.net

TABLE OF CONTENTS

TABLE OF CONTENTS

INTRODUCTION............................................................. 1

CPM-700 PACKAGES .............................................. 2

FEATURES OF THE CPM................................................... 5

POWER SUPPLIES, PROBES, ACCESSORIES .................. 5

FRONT PANEL FEATURES ......................................... 9

AUDIO GROUP ......................................................9

MONITOR GROUP.................................................. 9

DISPLAY GROUP .................................................. 10

PROBE GROUP .................................................... 11

SIDE PANEL FEATURES........................................... 11

POWER SOURCES......................................................... 13

ALKALINE BATTERY OPERATION .............................. 13

AC ADAPTER OPERATION ...................................... 13

OPTIONAL RECHARGEABLE BATTERY OPERATION....... 13

CHARGING INSTRUCTIONS ................................... 13

BASIC CPM-700 RF PROCEDURE.................................... 15

RF CONSIDERATIONS ........................................... 16

PERFORMING A “WALK AROUND ROOM SWEEP” ....... 16

DETAILED CPM-700 PROCEDURE................................... 19

METER CALIBRATION ............................................ 19

KNOWN SOUND SOURCE ..................................... 19

RF PROBE ANALYSIS ............................................. 20

BROADBAND RF ANALYSIS (2GHZ – 12GHZ) ............. 22

DETAILED INSPECTION SWEEP................................ 24

PHONE/LINE RF SWEEP ......................................... 25

TRACKING DEVICES.............................................. 26

VLF PROBE.......................................................... 27

AUDIO TESTING .................................................. 29

MISC. WIRE / AUDIO EVALUATION .......................... 30

PLANNING AND CONDUCTING A SWEEP...................... 31

SWEEP PREPARATION............................................ 31

ESTABLISH A “GAME PLAN”.................................... 31

SWEEP TIPS ......................................................... 32

PHYSICAL SEARCH................................................ 34

i REI CPM-700

TABLE OF CONTENTS

OTHER PROCEDURES AND EQUIPMENT ........................ 37

SPECIFICATIONS........................................................... 41

WARNINGS .................................................................. 45

REI CPM-700 ii

INTRODUCTION

INTRODUCTION

The CPM-700 Countersurveillance Probe/Monitor is a universal sweep tool
that can be used to detect and locate a wide variety of surveillance devices.
A broad range of probes and accessories are available for the CPM-700 to
expand the CPM’s countersurveillance capabilities.

NOTE: Depending on the CPM-700 package purchased, and/or
additional probes purchased, you may or may not have all the
probes and accessories discussed in this manual.

The CPM-700 detects and locates transmitting devices, quickly and silently,
including:

• AF (Audio Frequency)……...100 Hz to 15 kHz.

• VLF (Very Low Frequency)….15 kHz to 1 MHz and carrier current

• RF (Radio Frequency...……..50 kHz to 3 GHz

With the additional probes and accessories, the CPM can detect and
locate:

• High Frequency transmitters (3 - 12 GHz, such as 802.11 wireless
networks and 5.8 GHz cordless telephones, with BMP-1200)

• Infrared transmitters (with IRP-700)

• Magnetic Leakage (with MLP-700)

• Acoustic Leakage vulnerability (with ALP-700)

Special Note

Familiarization with the level of threat, the physical and technical
environment, and most importantly the capabilities of the CPM­700 is critical to using the CPM-700 successfully. In an area as
sensitive as countersurveillance, it may be necessary for you to
employ other supplementary equipment and/or procedures.

The section “Planning and Conducting a Sweep” contains many
practical tips for getting the most out of your CPM and other
countersurveillance equipment.

1 REI CPM-700

INTRODUCTION

CPM-700 PACKAGES

Several probes and accessories (some of which are optional) are available
for the CPM-700. Many of these probes and accessories are available
separately, but also in the packages listed below:

CPM-700 STANDARD

The CPM-700 STANDARD package provides the basic tools for
users who are only concerned with minimal RF testing; the CPM­700 STANDARD package includes the following:

• CPM-700 Countersurveillance Probe/Monitor

• Standard RF Probe (50kHz-3GHz)

• VLF Carrier Current Probe

• TVLF Patch Cable

• Auxiliary Patch Cable

• Headphones

• Soft carrying case

This is the most basic package providing for TSCM RF testing up to
3GHz.

CPM-700 ADVANCED PACKAGE

The CPM-700 ADVANCED package is designed for users who
have a need for additional TSCM testing (IR, Acoustic Leakage,
Network and Telephone wiring testing, etc.). This package also
provides several convenience accessories and includes the
following:

• CPM-700 Countersurveillance Probe/Monitor

• Standard RF Probe (50kHz-3GHz)

• Acoustic Leakage Probe

• Infrared Probe

• VLF Carrier Current Probe

• TVLF Patch Cable

• Magnetic Leakage Probe

• Auxiliary Patch Cable

• Modular Phone Adapter for network and phone line

testing

• Tape Recorder Patch Cords

REI CPM-700 2

INTRODUCTION

• Cigarette Lighter Adapter for powering the CPM from a
12VDC automobile socket

• Rechargeable Batteries

• Headphones

• Soft carrying case

This package includes several accessories for RF analysis up to
3GHz, Infrared analysis, acoustic leakage testing, network and
telephone testing adaptors, and other accessories.

CPM-700 DELUXE PACKAGE (12GHz)

The CPM-700 DELUXE package is designed for the serious TSCM
user who wants to get the most out of the CPM-700. This package
includes all currently available probes and accessories, including the
directional Broadband Microwave Probe, which extends the range of
the CPM-700 to 12GHz and adds additional sensitivity in the
common 2.4 GHz range over the Standard RF Probe. The CPM­700 DELUXE package includes the following:

• CPM-700 Countersurveillance Probe/Monitor

• Standard RF Probe, frequency range of 50kHz-3GHz

• Broadband Microwave Probe (BMP-1200), frequency range

of 2GHz-12GHz (This probe is directional and much more
sensitive than the standard RF probe in the common

2.4GHz range.)

• Acoustic Leakage Probe for evaluating structural bound
audio leakage

• RF Sniffer Probe (10MHz-3GHz) for pinpointing surveillance
devices where the Standard RF Probe may become
saturated with RF energy

• Infrared Probe

• VLF Carrier Current Probe

• TVLF Patch Cable

• Magnetic Leakage Probe

• Auxiliary Patch Cord

• Modular Phone Adapter for network and phone line testing

• Tape Recorder Patch Cords

• Cigarette Lighter Adapter for powering the CPM from a

12VDC automobile socket

• Rechargeable Batteries

3 REI CPM-700

INTRODUCTION

• Headphones

• Deluxe Hard-shell Case to carry the CPM and all probes

and accessories

The CPM-700 Deluxe package includes all current available probes
(including RF up to 12GHz, Infrared, Carrier Current, Acoustic
Leakage, etc.), and all available accessories and provides the widest
range of test capabilities with the CPM.

Most of the probes and accessories are available separately for
replacement; contact REI for replacement probes.

BMP-1200 Broadband Microwave Probe Upgrade

For CPM owners who would like to add the Broadband Microwave Probe
(BMP-1200) to their existing CPM (extending the frequency range to
12GHz), REI offers the BMP-1200 Upgrade package, which is backwards
compatible with all existing CPMs. The BMP-1200 Upgrade includes the
following:

• BMP-1200 Probe (2GHz-12GHz)

• RF Sniffer Probe (10MHz-3GHz)

• Acoustic Leakage Probe

• Deluxe Hard-shell Case

The CPM-700 provides a wide range of tools in a single easy-to-use
portable kit. Whatever your needs, there is a CPM package that will
accommodate you.

REI CPM-700 4

FEATURES OF THE CPM

FEATURES OF THE CPM

POWER SUPPLIES, PROBES, ACCESSORIES

1. Power Sources / Selector Switch:

a. Alkaline Batteries (8 AA cells) - Remove back cover of CPM by

turning two fasteners one-quarter turn counterclockwise. Set the
switch to “ALKALINE.”

Selector switch in back of CPM is factory set to “ALKALINE”

Do not charge Alkaline batteries. Damage to the unit will occur.

b. Using Rechargeable Ni-MH or Ni-Cad Batteries

(8 AA cells) – Set the switch to “RECHARGEABLE.”
Charge at least eight hours or overnight. Connect the AC
adapter to the side of the CPM and plug in to a wall outlet.
All rechargeable batteries must be charged before use.

c. AC Adaptor – Connect the adapter supplied by REI to an AC

outlet and to the Adapter input of the CPM-700. If rechargeable
batteries are installed, the AC adapter will charge them. The
CPM-700 will automatically operate on the battery pack if the
AC power fails. NOTE: Do not use any adapter other than the
one supplied by REI.

5 REI CPM-700

FEATURES OF THE CPM

2. Standard RF Probe: Checks your
environment for hidden phone or
room-audio bugs; video
transmitters; pulsed tracking
transmitters; remote control,
frequency-hopping, spread­spectrum, and burst devices up to
3GHz.

a. VLF Probe: Tests for carrier-current

With TVLF adapter attached to
the VLF probe, test for carrier
current devices on any pair of
conductors.

bugs that use AC wiring (or other
misc. wiring like telephone, burglar
alarm, thermostat wiring, etc.) as a
transmission path.

3. The high sensitivity Auxiliary
Input Amplifier allows you to
listen to suspicious telephone
or room wiring for the
presence of buried
microphones or modifications
to equipment.

REI CPM-700 6

4. BMP-1200 Broadband
Microwave Probe – Receives RF
energy between 2GHz and
12GHz, including frequencies
used for wireless networks and
many cordless telephones.

5. RF “Sniffer” Probe – Helps to

6. IRP-700 Infrared Probe – Locates
infrared transmissions.

7. MLP-700 Magnetic Leakage Probe –
Locates carrier current devices, tape
recorders and video cameras.

FEATURES OF THE CPM

isolate ‘threat’ transmissions from
legitimate broadcast transmissions
in RF-rich environments up to
3GHz. Must check within 18” of
every object in the target area.

7 REI CPM-700

FEATURES OF THE CPM

8. MPA Modular Phone Adaptor – Rapidly tests each pair of conductors in
telephone and network cables or carrier current or audio transmissions

Testing for carrier
current devices

Testing for line
audio

Modular Phone

Adapter (MPA)

Cable from
telephone

TVLF Adaptor

Auxiliary Patch
Cable

VLF Probe

To CPM

To CPM

9. TVLF Adaptor – Adapts VLF Probe to check any kind of wiring (not just
wall outlets) for carrier current devices (see above).

10. ALP-700 Acoustic Leakage
Probe – Detects and evaluates
areas vulnerable to acoustic
leakage. (Also used with testing
of REI’s ANG 2200 – Acoustic
Noise Masking System.)

11. NCB – Rechargeable battery pack, 8 Ni-MH cells, size AA

12. CLA – 12 VDC automotive cigarette lighter adapter

REI CPM-700 8

FEATURES OF THE CPM

FRONT PANEL FEATURES

1

2

6

7

8

9

11

3

4

5

10

12

AUDIO GROUP

PHONES (1): Allows the use of silent headphone detection, disconnects the
internal speaker.

GAIN (2): Controls the Audio Gain (volume) to the speaker or Headphone
Output. Does not affect Record Out level.

FILTER (3): The audio Filter will “band-pass” the audio
response for voice levels by enhancing the 500 Hz to 2.5 kHz
frequencies. The Filter also removes much of the AC hum on
the Auxiliary Input, or video hum when using the RF Probe
Input. The Filter processes the audio for both the headphones and the
record-out jack. Display shows whether filter is IN or OUT.

MONITOR GROUP

MODE (4): Sets the unit to its Search or Monitor function.
The SEARCH mode is used for performing a sweep. The
MONITOR mode is used after a sweep to check continually
for new devices. Display shows whether Mode is SEARCH or
MONITOR

With the CPM in MONITOR mode, a new signal stronger than the
THRESHOLD level (see below) will cause the ALERT LED to flash, and the
CPM will make an audible TONE.

9 REI CPM-700

FEATURES OF THE CPM

The remaining functions in this group are active only while in the MONITOR mode:

SILENT/TONE (5): Silences the audible beeper during an
ALERT. The LED will continue to flash. Display shows whether
CPM is in TONE or SILENT mode.

THRESHOLD (6): Moves a pulsing segment to any position on the LCD Bar
graph. When the input level exceeds the pulsing segment, the CPM-700
enters an Alert Mode and activates the Remote Output.

The THRESHOLD control is active only in the MONITOR mode.

ALERT (7): LED flashes red while in ALERT mode.

DISPLAY GROUP

INPUT LEVEL (8): Bar graph indicates signal strength of Probe or Auxiliary
Inputs; compressed semi-logarithmic with two sensitivity scales.

PULSING SEGMENT (9): In MONITOR mode only, displays the Threshold
Point that will activate the Alert mode and Remote Output.

LOW BATT (not shown): Battery voltage indicator; indicates approximately
10% remaining power.

STATUS DISPLAY (10): Shows unit operating conditions made by switch
selections and input used.

NOTE: This status display figure is used in this manual to help you verify
the current setup. Only one label per block appears at any one time on the
actual display, depending on the switch settings.

REI CPM-700 10

FEATURES OF THE CPM

PROBE GROUP

PROBE (11): Input jack for CPM probes. This jack also
provides power to “active” CPM probes. The CPM-700 will
automatically select this input when a CPM Probe is
connected.
Connect only CPM probes to this jack. Display shows whether PROBE or
AUX jack is in use.

GAIN (12): Selects the internal sensitivity of the Bar graph
and audio systems. The HIGH position provides additional
Gain to boost low-level input signals. Display shows whether
HIGH Gain or LOW gain is selected.

SIDE PANEL FEATURES

A B C D E F

A. AUXILIARY INPUT: Audio input for internal amplifier. Use to test

wires for the presence of audio or control signals.

B. METER: Calibrates the LCD Bar graph to the HIGH GAIN setting.

C. REMOTE: Connects to “remote” compatible input of audio

recorder. Use to start/stop the recording function.

D. RECORD: Provides low level audio output of received sounds,

connects to “microphone” input of recorder.

E. CHARGE: LED indicates charging of nickel-metal-hydride battery.

F. ADAPTER: Accepts power from AC Adapter, and charges nickel-

metal-hydride battery pack (make sure switch is set to
“RECHARGEABLE”).

11 REI CPM-700