KitSound BoomBar User Manual
PLEASE NOTE:
Your device will have an internal amplifier and if it is playing
digital files like MP3s it will also have an integrated DAC
(Digital Audio Converter). If you turn up the volume to
100%, your device will be sending distorted signals to the
BoomBar. To avoid this and to get the best sound quality
from the speaker, we recommend that you do not run your
device any higher than 95% volume.
Hands-free
The speaker comes equipped with a microphone so you
can take phone call s whilst connected. Should you receive
an incoming phone call, the Play/Pause button (6) becomes
an Ans wer/ End call button. If you recei ve a call whilst
music is play ing, press the Play/Pause button to answer.
To end the call, press the Pl ay/Pause button again and your
music should resume playing (dependant on device).
BOOMBAR
WIRELESS
Troubleshooting
We hope you’ve now got all the information you need to
get started, but if you’re having problems with anything,
please feel free to contact us on: support@kitsound.co.uk
Bluetooth v2.1, A2DP, AVRCP
Bluetooth range up to 10 m
Output RMS 2 x 2 W @ 4 ohm
S/N 85 dB
Play time up to 20 hours
Charging time up to 3 hours
SPEAKER
USER MANUAL
kitsound.co.uk
JB. 2586 / Made in China. © KitS ound™ 2013
Christchu rch, Dorset. BH23 4FL
Please rec ycle this packagi ng respons ibly.
Do not dispose of Lithium Polymer
batteries with general waste.
Please return it to battery recycling
collection point
Li-PO
Box contents:
• BoomBar wireless speaker
• Mini USB charging cable
• 3.5 mm to 3.5 mm auxiliar y cable
• Case
• User manual
Functions:
1. ON/OFF Switch
2. 5 V DC mini USB port socket
3. Aux (3.5 mm) socket
4. Microphone
Using the BoomB ar
Charging the speaker
It is recommended that you give the speaker a full charge
before its first use.
1. Plug the Mini USB end of the charging cable into
the speaker.
2. Plug the standard USB end into either a computer or
a USB mains charger.
3. A solid red light will show on the front of the speaker.
4. The light will go out when it is fully charged.
NOTE: It may take up to 4 hours before it is fully charged.
1
3
2
4
5. Next Track/ Volume +
6. Play/Pause/Pair
7. Previous Track/ Volume –
8. LED status light
9. Battery cover
10. Slot (insert coin or supplied disk) for stand
9 10
Pairing the speaker to your device
Before you can use the speaker via Bluetooth, it will need
to be paired to your device.
To do this:
1. Slide the power switch to the ‘ON’ position (1).
2. Wait for about 8 seconds then press (do not hold) the
Play/Pause button (6).
3. The speaker’s LED should flash red and blue alternately.
4. Turn your device’s Bluetooth ON and search for new
devices.
5. When the speaker appears in the list, select it and if
asked for a pass code, enter ‘0000’.
6. The speaker should then be paired to your device.
Play ing music on your speaker
Changing the volume
This can be done on both the device you are playing music
5
6
7
8
from and on the speaker.
To change the volume on the speaker, press and hold (do not
shor t press otherw ise it may skip track) either the Volume +
(5) or Volume – (7) button.
Bluetooth
If already connec ted to the speaker via Bluetooth, simply find
and play the music on your device and the sound will play
through the speaker. Some devices may require you to select
the audio output. You should be able to do this by going to the
‘Listen via’ or ‘Play via’ menu. If unsure, please refer to your
device’s manual.
If you are using an A 2DP Bluetooth-enabled device, you will
be able to use the following functions on the speaker:
• Play/Pause (6) – Short press
• Next Track (5) – Shor t press
• Previous Track (7) – Short press
Auxiliary
Using the provided cable, you can connect your device
direc tly to the speaker.
To use this, simply:
• Slide the power switch to the ‘ON’ position (1)
• Plug the cable into the speaker’s Aux socket (3) and
your device
• Press play on your device
When playing music using the cable, you will not be able to
use the Play/Pause, Nex t Track and Prev ious Track functions
or change the volume on the speaker.
Loading...