How it Works
KitchenAid
Loading...
YWMH53520CB1
Installation Guide
12 pgs860.22 Kb0

KitchenAid YWMH53520CS1, YWMH53520CB1, YWMH53520CH1, YKMHS120EW2, YKMHS120EW1 Installation Guide

...
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See “Installation Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in these installation instructions.
INSTRUCTIONS D’INSTALLATION
DE L’ENSEMBLE FOUR À MICRO-ONDES/HOTTE
Ces instructions d’installation sont valables pour plusieurs modèles. Il se peut que l’apparence de votre propre modèle soit légèrement différente de celle montrée sur les illustrations dans ce document.
MICROWAVE HOOD COMBINATION SAFETY ......................................... 1
INSTALLATION REQUIREMENTS .............................................................. 2
Tools and Parts ......................................................................................... 2
Location Requirements ............................................................................ 2
Product Dimensions ................................................................................. 3
Electrical Requirements ............................................................................ 3
INSTALLATION INSTRUCTIONS ................................................................ 4
Remove Mounting Plate ........................................................................... 4
Rotate Blower Motor ................................................................................ 4
Locate Wall Stud(s) ................................................................................... 6
Mark Rear Wall .......................................................................................... 7
Drill Holes in Rear Wall..............................................................................7
Attach Mounting Plate to Wall .................................................................. 8
Prepare Upper Cabinet ............................................................................. 8
Install Damper Assembly .......................................................................... 9
Install the Microwave Oven ...................................................................... 9
Complete Installation .............................................................................. 10
VENTING DESIGN SPECIFICATIONS ...................................................... 11
ASSISTANCE .............................................................................................12
Replacement Parts ................................................................................. 12
Accessories............................................................................................. 12
SÉCURITÉ DE L’ENSEMBLE FOUR À MICRO-ONDES/HOTTE ........... 13
EXIGENCES D’INSTALLATION ................................................................ 13
Outillage et pièces .................................................................................. 13
Exigences d’emplacement ..................................................................... 14
Dimensions du produit ........................................................................... 14
Spécifications électriques....................................................................... 15
INSTRUCTIONS D’INSTALLATION .......................................................... 15
Dépose de la plaque de montage .......................................................... 15
Réorientation du moteur du ventilateur .................................................. 15
Identifier la position du/des poteau(x) du colombage mural ................. 17
Tracé sur le mur arrière ........................................................................... 18
Perçage de trous dans le mur arrière ..................................................... 19
Fixation de la plaque de montage sur le mur ......................................... 19
Préparation du placard supérieur ........................................................... 20
Installation du module du clapet anti-reflux ........................................... 21
Installation du four à micro-ondes .......................................................... 21
Achever l’installation ............................................................................... 22
SPÉCIFICATIONS/CONCEPTION DU CIRCUIT D’ÉVACUATION ......... 23
ASSISTANCE .............................................................................................24
Pièces de rechange ................................................................................ 24
Accessoires ............................................................................................. 24
MICROWAVE HOOD COMBINATION SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
Table of Contents / Table des matières
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
follow instructions.
You
can be killed or seriously injured if you don't
instructions.
W10823837A
follow
INSTALLATION REQUIREMENTS
Tools and Parts
Tools Needed:
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
■ Measuring tape
■ Pencil
■ Masking tape or
thumbtacks
■ Scissors
■ No. 2 Phillips screwdriver
■ No. 3 Phillips screwdriver
for 1/4-20 x 3" bolts
■ Drill
■ 3/16" (5 mm), 3/8" (10 mm),
5/8" (16 mm) drill bits
■ 3/4" (19 mm) hole saw
Parts Supplied:
For information on reordering, see “Replacement Parts” section. NOTE: The hardware items listed here are for wood studs.
For other types of wall structures, be sure to use appropriate fasteners.
A
B
C
■ Diagonal wire cutting pliers
■ Stud finder
■ 7/16" socket wrench
(or box wrench) for 1/4" x 2" lag screws
1
■ 1
/2" (3.8 cm) diam. hole drill bit for wood or metal cabinet
■ Keyhole saw
■ Caulking gun and
weatherproof caulking compound
■ Duct tape
D E F
H
G
Location Requirements
Check the opening where the microwave oven will be installed. The location must provide:
■ Minimum installation dimensions. See “Installation
Dimensions” illustration.
■ Minimum one 2" x 4" (50.8 x 101.6 mm) wood wall stud
and minimum 3/8" (10 mm) thickness drywall or plaster/lath within cabinet opening.
■ Support for weight of 150 lbs (68 kg), which includes
microwave oven and items placed inside the microwave oven and upper cabinet.
■ Grounded electrical outlet inside upper cabinet.
See “Electrical Requirements” section.
NOTES:
■ If installing the microwave oven near a left sidewall, make
sure there is at least 6" (15.2 cm) of clearance between the wall and the microwave oven, so that the door can open fully.
■ Some cabinet and building materials are not designed
to withstand the heat produced by the microwave oven for cooking. Check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damages.
Special Requirements
For Wall Venting Installation Only:
■ Cutout must be free of any obstructions so that the vent
fits properly, and the damper blade opens freely and fully.
For Roof Venting Installation Only:
■ If you are using a rectangular to round transition piece,
the 3" (7.6 cm) clearance needs to exist above the microwave oven so that the damper blade can open freely and fully. See “Rectangular to Round Transition” illustration in “Venting Design Specifications” section.
A. 3/16-24 x 3" round-head bolts (2) B. 1/4-20 x 3" flat-head bolts (2) C. Washers (2) D. 3/16" toggle nuts (2) E. 1/4" x 2" lag screws (2) F. Sheet metal screws (2) G. Power supply cord bushing (1) H. Damper assembly (for wall
or roof venting)
Not Shown:
Upper cabinet template Mounting plate (attached
to back of microwave oven) Wall template Aluminum grease filters Charcoal filters (Depending
on model, charcoal filters
may not be included.
See User Instructions.)
NOTE: Depending on model, aluminum grease filter and charcoal filter may be combined.
Materials needed:
■ Standard fittings for wall or roof venting.
See “Venting Design Specifications” section.
2
Installation Dimensions:
A B
(43.5 cm)
(41.3 cm)
NOTE: The grounded 3 prong outlet must be inside the upper cabinet. See “Electrical Requirements” section.
12" (30.5 cm) min. 14" (35.6 cm) max. upper cabinet and
side cabinet depth
66" (167.6 cm) min.
30"
(76.2 cm)
min.
30"
(76.2 cm)
typical*
Electrical Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.
Observe all governing codes and ordinances.
Required:
■ A 120 volt, 60 Hz, AC only, 15- or 20-amp electrical supply
with a fuse or circuit breaker.
Recommended:
■ A time-delay fuse or time-delay circuit breaker.
■ A separate circuit serving only this microwave oven.
A. 2" x 4" wall stud B. Grounded 3 prong outlet
* 30" (76.2 cm) is typical for 66" (167.6 cm) installation
height. Exact dimensions may vary depending on type of range/cooktop below.
Product Dimensions
Up to
³⁄₄
"
⁷⁄₈
29
" (76.0 cm)
"
¹⁄₈
17
"
³⁄₁₆
+/­(0.5 cm)
16
(42.5 cm)*
* Overall depth of product will vary slightly depending
on door design.
GROUNDING INSTRUCTIONS
■
For all cord connected appliances:
The microwave oven must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. The microwave oven is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
WARNING: Improper use of the grounding plug can
"
¹⁄₄
16
result in a risk of electric shock. Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or if doubt exists as to whether the microwave oven is properly grounded.
Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the microwave oven.
SAVE THESE INSTRUCTIONS
3
INSTALLATION INSTRUCTIONS
A
A
A
Remove Mounting Plate
Depending on your model, the mounting plate may be in the foam packaging, or it may be attached to the back of the microwave oven.
NOTE: To avoid possible damage to the work surface, cover the work surface.
1. Remove any remaining contents from the microwave
oven cavity.
2. If the mounting plate is attached to the back of
the microwave oven, remove it and set it aside.
3. Tape the microwave oven door closed so that door does
not swing open while the microwave oven is being handled.
NOTE: To avoid damage to the microwave oven, do not grip or use the door or door handle while the microwave oven is being handled.
Rotate Blower Motor
The microwave oven is set for recirculation installation. For wall or roof venting, changes must be made to the venting system.
NOTE: Skip this section if you are using recirculation installation. Keep the damper assembly in case the venting method is changed or the microwave oven is reinstalled in another location where wall or roof venting may be used.
Wall Venting Installation Only
1. Remove screws attaching damper plate to top of microwave
oven exterior. Slide damper plate toward the front of the microwave oven and lift up.
3. Remove 2 screws attaching blower motor to back
of microwave oven.
A
A. Screws (in recessed holes)
4. Lift blower motor out of microwave oven.
A. Blower motor
5. Rotate blower motor 180° so that exhaust ports face
the back of microwave oven, and lower blower motor back into the microwave oven.
B
A. Screws B. Damper plate
2. Keep damper plate and screws together and set aside.
A. Exhaust port
4
Loading...
+ 8 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use