KitchenAid YKERC508LS0, YKERC507HW3, YKERC507HW4, YKERC507HT3, YKERC507HT4 Installation Guide

...

9752777C

instructions

d'installation

Cuisini_re

61ectrique

autonome 76,2

OLI

Piece N ° 9752777 Rev. C

cm (30 po)

I cm (24 po)

Installation Instructions

" (76.2 cm)

or 24" (61 cm)

ectric

Part No. 9752777 Rev. C

Freestanding

an e

Risque de basculement

Un enfant ou un adulte peut faire basculer la cuisini_re et peut causer un

d_c_s.

Fixer la bride antibasculement sur le plancher pour qu'elle accroche le pied

arri_re de la cuisini_re.

R_installer la bride antibasculement apr_s un d_piacement de I'apparei!. Le non=respect de ces instructions peut causer un d_c_s ou de graves

brQlures & un enfant ou un aduite.

MPORTANT ."

Lire et conserver ces instructions.

IMPORTANT : Installateur : Remettre les instructions d'installation au proprietaire.

Propri_taire : Conserver les instructions d'installation pour consultation

ulterieure, ainsi que le gabarit de la bride antibasculement.

Conserver les instructions d'installation pour consultation

par I'inspecteur local des installations electriques.

Tip Over Hazard A child or adult can tip the range and be killed. Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved. Failure to follow these instructions can result in death or serious burns to

children and adults.

IMPORTANT:

Read and save these instructions.

IMPORTANT: Installer: Leave Installation Instructions with the homeowner.

Homeowner: Keep Installation Instructions and anti-tip bracket template for

future reference.

Save Installation Instructions for local electrical inspector's use.

Before you start...

Cabinet opening dimensions

Your safety and the safety of others

are very important.

We have provided many important safety messages

in this manual and on your appliance. Always read

and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards

that can kill or hurt you and ethers.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential

hazard is, tell you how to reduce the chance of injury,

and tell you what can happen if the instructions are

not followed.

25" (63.5 cm) countertop depth 24" (61 cm) base cabinet depth

36" (91.4 cm) countertop height

clearance to the

cooktop, see

_PP"!_i7ebri_ _ _!_ _7_r_) ran)ge: NOTE.***

I _ For a 24" (61 cm) range: _.

4" (10.2 cm) j_"_.._'_ /wall receptacle or junction

IMPORTANT: Observe all of ran e to side rf i cabinet 7" (17 8 cm) maxg , . .

codes and ordinances, wall or other from floor.

Earthed/grounded electrical outlet is combustible required, material.

governing from both sides _, (55.9 cm) from either

min. clearance _ /box - 8" (20.3 cm) to 22"

"yFor minimum

of the

When installing a cooktop under existing cabinets and the installation does not meet the minimum cabinet

clearances, install a range hood above the cooktop to avoid burn hazards.

IMPORTANT: Observe all governing codes and ordinances. Failure to meet codes and ordinances could

lead to fire or electrical shock. Read electrical and carpentry instructions.

Proper installation is your responsibility. A qualified technician must install this range. Make sure you have

everything necessary for correct installation. It is the customer's responsibility to make sure that the installation

clearances specified on the model/serial rating plate are met. The model/serial rating plate is located on the frame

behind the drawer. Check location where range will be installed. The range

should be located for convenient use in the kitchen. Recessed installations must provide complete enclosure

of the sides and rear of range. All openings in the wall or floor where range is to be

installed must be sealed. IMPORTANT: Some cabinet and building materials are

not designed to withstand the heat produced by the oven for baking and self-cleaning. Check with your builder or

cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.

Cutout shown is for a 25-inch (63.5 cm) countertop with a 24-inch (61 cm) base cabinet.

Cabinet constructions: This appliance is designed for use in a base cabinet with a depth of 24 inches (61 cm). The maximum depth for overhead cabinets is 13 inches

(33 cm). For the minimum vertical clearance between the cooking surface and the overhead cabinets, see

NOTE***. Overhead cabinets installed at either side of the appliance must be a minimum of 18 inches (45.7 cm)

above the cooking surface. The minimum horizontal distance between the overhead cabinets is 30 inches

(76.2 cm). It is the customer's responsibility:

To contact a qualified electrical installer. To assure that the electrical installation is adequate and

in conformance with National Electrical Code, ANSI/NFPA 70 -- latest edition*, or CSA Standard C22.1, Canadian Electrical Code, Part 1 -- latest edition**, and all local codes and ordinances.

shown must be used. I t I _ Cabinet opening dimensions that are I __in.'_"_

"% _ door or hinge.

required between

cutout and cabinet

Product dimensions

i"_""_26 3/8" (67 cm)

depth with handle 26-5/8" (67.6 cm)

for stainless steel

handle (on some models)

30" (76.2 cm) width for 30" (76.2 cm) range

24" (6I cm) range

(118.9 cm)

46-13/16"

36"

(91.4 cm)

cooktop

height

(61 cm) width for

overall

height

Do not pinch the power supply cord between the range and the wall.

Do not seal range to side cabinets.

Mobile home installation

The installation of this range must conform to the

Manufactured Home Construction and Safety

Standards, Title 24 CFR, Part 3280 (formerly the

Federal Standard for Mobile Home Construction and

Safety, Title 24, HUD, Part 280); or when such standard is not applicable, the Standard for

Manufactured Homes Installations (Manufactured Home Sites, Communities and Setups), ANSI

A225.1/NFPA 501A, or with local codes*.

In Canada, the installation of this range must conform

with the current standard CAN/CSA-Z240 -- latest edition**, or with local codes.

When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms

to the standards listed above.

Four-wire power supply cable must abe used in a mobile home installation. The appliance wiring will

need to be revised.

Copies of the standards listed may be obtained from:

* National Fire Protection Association

Batterymarch Park Quincy, Massachusetts 02269

** CSA International

8501 East Pleasant Valley Rd. Cleveland, Ohio 44131-5575

*** NOTE: 24" (61 m) min.when bottom of wood or metal

cabinet is protected by not less than 1/4" (0.64 cm) flame retardant mitlboard covered with not less than No.

28 MSG sheet steel, 0.015" (0.4 ram) stainless steel,

0.024" (0.6 ram)aluminum or 0.020" (0/5 cm) copper. 30" (76.2 cm) rain. clearance between the top of the

cooking platform and the bottomof an unprotected

wood or metal cabinet.

.... NOTE: This dimension is for the 24" (61 cm) model.

Anti-tip bracket:

The floor anti-tip bracket must

be installed. To install the anti-

tip bracket shipped with the

range, see Panel B and the anti-

tip bracket template.

Panel A

Tools needed:

Assemble the required tools and parts before starting

installation. Read and follow the instructions provided

with any tools listed here.

level

flat-balde screwdriver or 5/16" nut driver

Phillips screwdriver

pliers adjustible wrench

hammer measureing tape or ruler

3/8" ratchet

hand or electric drill

wood floor: 1/8" drill bit concrete/ceramic floor: 3/16" carbide-tipped

masonry drill bit

Parts

_s anti-tip

supplied:

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to follow this instruction can result in back or other injury.

_ Firmly grasp the range and gently lay it on its

back on the cardboard corners.

_ Pull cardboard bottom and shipping base firmly

to remove.

_ Use an

adjustable wrench to loosen the leveling legs 1-1/2 turns.

[] Line up holes in anti-tip

bracket with holes in floor. Use the ( screws provided to fasten anti-tip _

bracket to floor. _, | NOTE: Anti-tip bracket must _ I _'_

be mounted securely to \ _,,' the sub floor. Depending \ _ on the thickness of your _

flooring, longer screws "_ _ may be necessary to _,. , _

anchor the bracket to the _ _ sub floor. Longer screws are _

available from your local hardware store.

Before moving, slide range onto cardboard or hardboard.

t [] Move range close to cabinet opening.

Make sure all controls are in the "OFF" position. Make electrical connection. If the factory installed power supply cord cannot be plugged into your outlet, have a qualified electrician install a matching earthed/grounded outlet. Do not modify the power supply cord.

Bracket must be securely

racket

2 screws _' anchors (#I0 x 1-I/2")

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot. Reconnect anti-tip bracket, if the range is

moved. Failure to follow these instructions can result in

death or serious burns to children and adults.

tic

Tip Over Hazard

mounted to sub-floor. Thickness of flooring may

require longer screws to anchor the bracket to sub-

floor.

Now start...

with range in kitchen

cardboard_ n

t corners

[] Remove shipping materials, ta

and protective film from range. Keep II [] [] cardboard bottom and shipping base_

under range. Remove oven racks, parts U.j _ J L_ package and all packing materials, spacers

including tape on elements, from inside oven.

[] Place cardboard or hardboard in front of range.

Stand range back up onto cardboard or hard board.

-- 25" (63.5 cm) countertop

_ Place the range

anti-tip bracket template on the floor in the cabinet

opening so that the left edge is against cabinet and the top edge is against the rear wall, molding or cabinet.

If countertop opening is

deeper than 25 inches 25" (63.5 cm), measure and

mark a distance 25 inches (63.5 cm) in

from front of countertop opening and align

template with mark (or subtract 25 inches

(63.5 cm) from countertop depth and add the

difference to the corresponding

dimension).

If countertop is not flush

to the side of cabinet opening, align the left

side of the template to -- allow for the countertop -- overhang. Tape the range anti-tip bracket template in place.

j cabinet

(63.5 cm)

over 24"

-" (61 cm)

overhangs cabinet

side.

A = Difference

between countertop

depth and 25" (63.5 cm).

| [] Remove cardboard or hardboard from

under range. Carefully move range into final position.

2 [] Press on front of

storage drawer and release to open. Pull open to first stop position. Lift front of drawer to

clear white wheels in drawer guides. Remove drawer and

set it aside on a protected surface.

J3, Look under range

(a flashlight may be needed) to check that left rear leveling leg is engaged in the anti-tip bracket. If leveling leg is not properly engaged, remove and reposition the anti-tip bracket to insure that the leveling leg fits properly in the anti-tip bracket.

in rack, first side to side; _-___/_ I

then front to back. If the___/j/J_ I

range is not level, pull __ I range forward until the --1 I

rear leveling leg is removed from the anti-tip bracket.

Adjust the leveling legs up or down. Then slide range

back into position. Check that leveling leg is engaged in anti-tip bracket.

NOTE: Oven must be level for satisfactory baking conditions.

[] Place rack ________z_-_

oven. Place level on ____

_ Take 4 cardboard

corners from the carton. Stack one cardboard

corner on top of another. Repeat with the other two corners. Place corners lengthwise on the floor in back of range so corners will support outer side edges of range as shown.

Contact a qualified floor covering installer for the best procedure of drilling mounting holes through your type

floor covering.

[] To mount anti-tip bracket to wood floor, use the anti-tip bracket template to mark where to

drill mounting holes. Use a drill with a 1/8" drill bit

to drill the two holes. Remove template from

floor.

To mount anti-tip bracket to concrete or ceramic

floor, use the anti-tip

bracket template to mark where to drill mounting holes. Use a drill with a 3/16" masonry drill bit to drill the two holes. Remove template from floor. Tap plastic anchors into mounting holes in floor with hammer.

lweS,:tohs1 d toe

sides oi drawer opening.

Lift front of drawer slightly _" I I / and push firmly to close drawer.

To get the most efficient use

from your new range,

read your Use and Care Guide.

Keep Installation Instructions and

Guide close to range

for easy reference.

Panel B

+ 4 hidden pages