KitchenAid YKEMC307KB03, YKEMC308KM02, YKEMC308KM03, YKEMC307KW01, YKEMC307KW03 Installation Guide

...

Quick Reference

Table of Contents:

Pages

[] Product dimensions [] Cutout dimensions

[] Before you start [] Electrical requirements

[] [] Installation steps

If you need assistance:

Check your Use and Care Guide for a toll-free number to call or call the dealer from whom you purchased

this appliance. The dealer is listed in the Yellow Pages of your phone directory under "Appliances- Household -- Major -- Service and Repair."

Call when you: [] Have questions about built-in oven installation or

operation.

[] Need to obtain the name and number of an

authorized service company.

When you call, you will need: [] The built-in oven model number.

[] The built-in oven serial number. Both numbers are listed on the model/serial rating

plate, located on the microwave oven frame.

27" 168.6 cm) oven

25-3/8" (64.5 crn)

recessed width ..............

41"

(104.1 crn)

recessed

height

42-7/16"

1107.8crn)

overall

height

41"

1104.1 crn)

recessed

height

Yoursafety and the safety of others are

veryimportant.

Wehaveprovided many important safety messagesin this manualand on your appliance. Always readand obey all safety messages.

This isthe safety alert symbol.

This symbolalerts youto potentialhazards that can kill or hurt you andothers.

All safety messageswill followthe safety alert symbol and eitherthe word "DANGER"or

"WARNING".Thesewords mean:

Youcanbe killed or seriouslyinjuredif you don'tfollow instructions.

All safety messageswill tell you what the potential hazardis,tell you howto reducethe chanceof injury, and tell you what can happenif the

instructions are not followed.

(58.4crn)\

recessed

depth

41-1/4"

1104.8crn)

cutout

height

23"

max,

_-_ 27" (68.6 crn) __

min.

cabinet width

25-1/2"

(54.8 crn) --

cutout

width

1"(2.5crn)top

of cutout to bottom of upper

cabinet door

23"

(58.4crn[

depth

41-1/4"

1104.8crn)

cutout

height

29-3/4

(75.6 crn)

erall width

__ 30"n_o,._..Lcrn)__

.___172.4 crn)

rnln.

cabinet

28-1/2"

cutout

width

1" (2.5 crn) top

of cutout

to bottom

of upper

cabinet door

important: Observe all governing codes and ordinances.

Proper installation is your responsibility. Have a qualified technician installthis oven.

Oven location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide

minimum clearance. Recessed installation area must provide

complete enclosure around the recessed portion of the oven.

Electrical ground is required. See "Electrical requirements."

Electrical supply junction box should be located 3 inches (7.6cm) maximum belowthe support

surface when oven is installedin a wall cabinet. Cutout for wiring should be inthe right rear or

left rear corner. For undercounter installation, it is recommended that the junction box be located inthe adjacent right or left cabinet. If installingjunction box on rear wall behind oven, junction box must be recessed and located in the upper or lower right or left corner of cabinet.

Oven support surface MUST be solid, level and flush with bottom of cabinet cutout.

1-112"

13.8crn) rnin. bottom of

cutout to top

of cabinet

door

cabinet

27" (68.6 cm} oven

23-1/4" 15&1 crn)

rnin.

cutout depth

._ 23" (58.4 crn)

recessed oven

depth

recessed

oven

Cabinet side view

1g-1/4"

(48.9 crn)

bottom of

cutout to

floor

{

oven

front

1-1/2"

(3.8 crn) rnin.

bottom of

cutout to top

of cabinet

door

30" (76.2 cm} oven

Cabinet filler kits are available from your dealer. Use a matching color kit if oven is smaller than your cabinet opening.

27" (68.6cm} oven filler height is 7-13/16"

119.8cm) Black -- 4378950

White -- 4378951 Almond- 4378952

30" (76.2cm} oven filler height is 4-13/16"

112.2cm) Black -- 4378944

White -- 4378945 Almond- 4378946

19-1/4"

(48.9crn)

bottom

of cutout

to floor

Toolneeded:

Phillips screwdriver

Partssupplied:

Excessive Microwave Energy Exposure

Do not attempt to operate the

microwave oven with the door open.

Do not tamper with or defeat the safety

interlocks.

Do not place objects between the

microwave oven front face and door.

Do not allow soil or cleaner residue to

accumulate on sealing surface of the microwave oven door.

Do not operate the microwave oven if

damaged.

Do not operate the microwave oven if:

-- door is bent.

-- hinges and latches are broken or loose.

-- door seals, sealing surfaces or

glass are broken.

The microwave oven door must close properly to provide safe operation.

Have a qualified repair person adjust, repair and check microwave oven for microwave leakage after a repair is

made.

Do not use microwave for commercial purposes. The microwave oven in this

unit is designed for household use only.

Failure to follow these instructions could result in exposure to excessive

microwave energy.

Page 1

Copies of the standards listed may be obtained from:

* National Fire Protection Association

Ratteryrnarch Park Quincy, Massachusetts 02269

** CSA International

8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575

It is the customer's responsibility: To contact a qualified electrical installer.

To assure that the electrical installation is adequate and in conformance with National

Electrical Code, ANSI/NFPA 70 m latest

edition*, or Canadian Electrical Code, 022.1- 1982 and C22.2 No. 01982 (or latestedition)**

and all local codes and ordinances.

ifcodespermitanda separate ground wire is

used,it is recommended that a qualified electriciandetermine that the ground path and wire gauge are in accordancewith local

codes. Do Not ground to a gas pipe.

Checkwith a qualified electrician if you are not sure oven is properly grounded.

Do Not have a fuse in the neutral or grounding circuit.

Do Not ground to a gas pipe. Checkwith a qualified electrician if you are

not sure oven is properly grounded. Do Not have a fuse in the neutral or ground

circuit.

This oven must be connected to a grounded metal, permanent wiring system.

Oven most be connected to the proper electrical voltage and frequency as specified

on the model/serial rating plate. (The model/serial rating plate is located on the

oven door or on the oven frame.) [] Models rated from 7.3 to 9.6 kW at 240

volts (5.5 to 7.2 kW at 208 volts) require a separate 40-ampere circuit. Models rated

at 7.2 kW and below at 240 volts (5.4 kW and below at 208 volts) require a separate

30-ampere circuit.

[] A time-delay fuse or circuit breaker is

recommended.

[] Connect directly to the fused disconnect

(or circuit breaker box) through flexible, armored or non-metallic sheathed, copper cable (with ground wire).

[] Flexible armored cable from appliance

should be connected directly to junction box.

[] Fuse both sides of the line.

[] A U.L.-listed conduit connector must be

provided atthe junction box.

[] Do Not cut the conduit. Wire sizes and connections must conform

with the rating of the appliance and to the requirements of the National Electrical Code,

ANSI/NFPA 70- latest edition (*, See Page 1) or Canadian Electrical Code, C22.1-1982and

C22.2 No. 01982 (or latest edition) (**, See Page 1) and all local codes and ordinances.

Ifthe house has aluminum wiring, follow the procedure below.

a.) Connect the aluminum wiring to the

copper wire using special connectors designed and Underwriters Laboratories- listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure.

b.) Aluminum/copper connection must

conform with local codes and industry- accepted wiring practice.

Preparation

Excessive Weight Hazard

Use two or more people to move and install oven.

Failure to follow this instruction can result in back or other injury.

Important: Use both handsto remove oven doors.

Do Not use handle or any portion of the

front frame or trim for lifting.

Before moving oven across floor, checkthat

oven is on shipping base or slide oven onto

cardboard or hardboard.

Do Not remove shipping feet at the front

lower corners of oven.

Remove side trim

pieces.

power

_ supply cable

Check oven and

.... I

microwave oven operation.

Use screws to attach oven to cabinet.

Do Not remove

shipping feet.

= Turn power supply off. Move oven

close to final position.

• Remove and discard shipping materials, tape and protective film from the oven.

Do Not remove shipping base or shipping feet at the front lower corners of oven.

The shipping feet will protect the lower oven trim until oven is inserted into

cabinet.

• Remove and set aside racks and other

parts from inside oven.

latch on the hinge in locked position -

door free to open and close

latch on the hinge in unlocked

position - door ready for removal

Removetrim screw.

Pulltrim out.

Pulltop of trim down.

Page 2

•, Completely open oven door. in both back corners of the door you will see door latches inthe locked position. Rotate both latches forward to the unlocked position.

Grasp outside edges of door with both hands.

• Begin closing door, atthe moment the door stops closing, lift and pull door toward you.

• Set door aside on a protective surface.

-, Remove trim screws attaching right

and left side trim to oven. Grasp the bottom end of trim and pull away from oven. Slide

top end of trim downward to remove trim

from oven. Takecare not to scratch other surfaces with ends of trim. Set trim and

screws aside on protected surface.

+ 7 hidden pages