KitchenAid YKEHSO2RWHO, YKEHSO2RMT0, KEHS02RWH0, KEHS02RMT0, KEHS01PMT2 Owner’s Manual

Ki|chen_kid _

FRONT-LOADING ELECTRIC DRYER

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

In Canada, call : 1-800-807-6777 or visit our website at...

www.kitchenaid.com or www.KitchenAid.ca

SECADORA ELECTRICA DE CARGA FRONTAL

Si tiene preguntas respecto alas caracterfsticas, funcionamiento/rendimiento, partes, accesorios o servicio t6cnico, Ilame al: 1-800-422-1230

Para la instalacion y servicio t6cnico Ilame al: 1-800-807-6777 o visite nuestro sitio web en... www.kitchenaid.com

P P ,_

SECHEUSE ELE.CIRQUE A CHARGEMENT

A L'AVANT

Au Canada, composez le 1-800-807-6777

ou visitez notre site web &... www.KitchenAid.ca

Table of Contents/indice/Table des matieres .................................................................. 2

8577195

TABLEOF CONTENTS

DRYER SAFETY .............................................................................. 3

INSTALLATION INSTRUCTIONS .................................................. 4

Tools and Parts ............................................................................ 4

Options ......................................................................................... 4

Location Requirements ................................................................ 5

Electrical Requirements - U.S.A. Only ......................................... 7

Electrical Requirements - Canada Only ....................................... 8

Electrical Connection - U.S.A. Only ............................................. 9

Venting Requirements ................................................................ 14

Plan Vent System ....................................................................... 15

Install Vent System ..................................................................... 16

Install Leveling Legs ................................................................... 16

Connect Vent .............................................................................. 16

Level Dwer ................................................................................. 17

Reverse Door Swing .................................................................. 17

Complete Installation ................................................................. 18

DRYER USE .................................................................................. 19

Starting Your Dwer ..................................................................... 19

INDICE

SEGURIDAD DE LA SECADORA ................................................ 29

INSTRUCCIONES DE INSTALACION ......................................... 30

Herramientas y piezas ................................................................ 30

Opciones .................................................................................... 30

Requisitos de ubicaci6n ............................................................ 30

Requisitos electricos -S61o en EE. UU ...................................... 32

Conexi6n electrica - S61oen EE. UU ......................................... 34

Requisitos de ventilaci6n ........................................................... 39

Planificaci6n del sistema de ventilaci6n .................................... 40

Instalaci6n del sistema de ventilaci6n ....................................... 42

Instalaci6n de las patas niveladoras .......................................... 42

Conexi6n del ducto de escape .................................................. 42

Nivelaci6n de la secadora .......................................................... 42

C6mo invertir el cierre de la puerta ............................................ 42

Complete la instalaci6n - EE, UU............................................... 44

USO DE LA SECADORA .............................................................. 45

Puesta en marcha de la secadora ............................................. 45

Detenci6n de la marcha de la secadora .................................... 46

Stopping Your Dwer ................................................................... 20

Pausing or Restarting ................................................................. 20

Control Locked ........................................................................... 20

Dwing and Cycle Tips ................................................................ 20

Status Lights ............................................................................... 21

Cycles ......................................................................................... 21

Additional Features .................................................................... 22

Dwing Rack ................................................................................ 23

DRYER CARE ............................................................................... 24

Cleaning the Dryer Location ....................................................... 24

Cleaning the Lint Screen ............................................................ 24

Cleaning the Dryer Interior ......................................................... 24

Removing Accumulated Lint ...................................................... 24

Vacation and Moving Care ......................................................... 24

Changing the Drum Light ........................................................... 25

TROUBLESHOOTING .................................................................. 25

ASSISTANCE OR SERVICE ......................................................... 27

WARRANTY .................................................................................. 28

Pausa o reanudaci6n de la marcha ........................................... 46

Control bloqueado ..................................................................... 46

Sugerencias de ciclos y secado ................................................ 46

Luces de estado ......................................................................... 47

Ciclos .......................................................................................... 47

Caracterfsticas adicionales ........................................................ 48

Estante de secado ...................................................................... 49

CUIDADO DE LA SECADORA ..................................................... 50

Limpieza del lugar donde esta la secadora ............................... 50

Limpieza del filtro de pelusa ...................................................... 50

Limpieza del interior de la secadora .......................................... 51

Eliminaci6n de pelusa acumulada ............................................. 51

Cuidado para las vacaciones y la mudanza .............................. 51

Cambio de la luz del tambor ...................................................... 51

SOLUCION DE PROBLEMAS ...................................................... 52

AYUDA O SERVICIO TI_CNICO ................................................... 54

GARANTIA ..................................................................................... 55

TABLE DES MATIERES

SI_CURITI:!:DE LA SI_CHEUSE .................................................... 56

INSTRUCTIONS D'INSTALLATION ............................................ 57

Outillage et pieces ...................................................................... 57

Options ....................................................................................... 57

Exigences d'emplacement ......................................................... 57

Specifications electriques - Canada seulement ........................ 59

Exigences concernant I'evacuation ........................................... 60

Planification du syst_me d'evacuation ...................................... 61

Installation du conduit d'evacuation .......................................... 63

Installation des pieds de nivellement ......................................... 63

Conduit d'evacuation ................................................................. 63

Mise a niveau de la secheuse .................................................... 63

Inversion de I'ouverture de la porte ........................................... 63

Achever I'installation .................................................................. 65

UTILISATION DE LA Sr!:CHEUSE ................................................ 66

Mise en marche de la secheuse ................................................ 66

Arr_t de la secheuse .................................................................. 67

Arr_t ou remise en marche ......................................................... 67

Verrouillage des commandes ..................................................... 67

Conseils pour le sechage et les programmes ........................... 67

Temoins lumineux ...................................................................... 68

Programmes ............................................................................... 68

Caracteristiques suppl_mentaires ............................................. 69

Grille de sechage ........................................................................ 70

ENTRETIEN DE LA SI_CHEUSE ................................................. 71

Nettoyage de I'emplacement de

la secheuse ................................................................................. 71

Nettoyage du filtre a charpie ...................................................... 71

Nettoyage de I'interieur de la secheuse ..................................... 72

Retrait de la charpie accumulee ................................................ 72

Precautions a prendre pour les vacances et avant un

demenagement .......................................................................... 72

Changement de I'ampoule d'eclairage du tambour .................. 72

Dr!:PANNAGE ................................................................................. 73

ASSISTANCE OU SERVICE ......................................................... 75

GARANTI E ..................................................................................... 75

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

Read all instructions before using the dryer. Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire. Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry- cleaning soivents, other flammable, or explosive substances as they give off vapors that could ignite or

explode. Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is used near children.

Before the dryer is removed from service or discarded, remove the door to the drying compartment.

Do not reach into the dryer if the drum is moving.

Do not install or store the dryer where it will be exposed

to the weather.

Do not tamper with controls.

SAVE THESE iNSTRUCTiONS

Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair

instructions that you understand and have the skills to carry out,

Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

Clean lint screen before or after each load, Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust, and dirt.

m The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel. See installation instructions for grounding requirements.

INSTALLATION INSTRUCTIONS

Gather the required tools and parts before starting installation. Read and follow the safety instructions provided with any tools

listed here.

• Flat-blade screwdriver • Wire stripper (direct wire

• #2 Phillips screwdriver installations)

• Adjustable wrench that • Level opens to 1" (2.5 cm) or • Vent clamps

hex-head socket wrench (for adjusting dryer feet) • Caulking gun and

• 1/4"nut driver new exhaust vent) (recommended) • Tin snips (new vent

Parts supplied

Remove parts packages from dryer drum. Check that all parts are included.

4 Leveling legs

NOTE: Do not use leveling legs if installing the dryer on a pedestal.

Parts needed

Check local codes. Check existing electrical supply and venting. See "Electrical Requirements" and "Venting Requirements" before purchasing parts.

• For close-clearance installations between 31.5" (80.01 cm) and 37" (93.98 cm), see "Plan Vent System" section for venting requirements.

compound (for installing

installations)

Pedestal

Are you placing the dryer on a pedestal? You may purchase a pedestal separately for this dryer. This pedestal will add about 13" (33 cm) to the height of your unit for a total height of approximately 51" (130 cm).

For a garage installation, you will need to place the pedestal at least 6" (15.2 cm) above the floor.

Optional pedestal

To order, call the dealer from whom you purchased your dryer or refer to the "Assistance or Service" section of this manual. Ask

for Part Number LAB2700PMT (Meteorite) or LAB2700MQ0 (White).

Stack Kit

Are you planning to stack your washer and dryer? To do so, you will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your dryer or refer to the "Assistance or Service" section of this manual. Ask

for Part Number 8541503.

I_- 37" --_1

(93_98 cm)

Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased

your dryer. For further information, please refer to the "Assistance

or Service" section of this manual.

Dryer Dimensions

ExplosionHazard

Keepflammablematerialsandvapors,suchas gasoline,away from dryer.

Place dryer at least 18 inches (48 cm) above the floor

for a garage installation.

Failure to do so can result in death, e×plosion, or fire.

You will need

• A location that allows for proper exhaust installation. See "Venting Requirements."

• A separate 30-amp circuit.

• If you are using a power supply cord, a grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See "Electrical Requirements."

• A sturdy floor to support the total dryer weight of 200 Ibs (90.7 kg). The combined weight of a companion appliance

should also be considered. A level floor with a maximum slope of 1" (2.5 cm) under entire

dryer. If slope is greater than 1" (2.5 cm), install Extended Dryer Feet Kit, Part Number 279810. Clothes may not tumble properly and automatic sensor cycles may not operate correctly if dryer is not level.

For a garage installation, you will need to place the dryer at least 18" (46 cm) above the floor. If using a pedestal, you will need to place the pedestal at least 6" (15.2 cm) above the

floor.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times.

The dryer must not be installed or stored in an area where it will

be exposed to water and/or weather. Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

(96.52 cm 1

(80cm) _"

%_ @(6&6 cm)

*Most installations require a minimum 51/2'' (14 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting Requirements."

Minimum installation spacing for custom undercounter installation

The dimensions shown are for the minimum spacing allowed. Custom undercounter installation - Dryer only

0" _ 27" _}._- 0"

(Ocm) _ (¢8.€cm) _ (Ocm)

Minimum installation spacing for recessed or closet installation, with or without a pedestal

• The dimensions shown are for the minimum spacing allowed. For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are

acceptable.

27"

Installation clearances

• The location must be large enough to allow the dryer door to open fully.

• Additional spacing should be considered for ease of installation and servicing.

• Additional clearances might be required for wall, door and floor moldings.

• Additional spacing of 1" (2.5 cm) on all sides of the dryer is recommended to reduce noise transfer.

• Companion appliance spacing should also be considered.

Closet installation - Dryer only

Recommended installation spacing for recessed or closet installation, with stacked washer and dryer

The dimensions shown are for the recommended spacing.

48 in?*

(310 cm2}

3"(7.6cm)

24 in?

(155 cm2}

Io,,t_ 3_,/,"_1 o,,*1

{0cm} (80 cm) {0cm}

A. Side view - closet or confined area

B. Closet door with vents

*Side or bottom venting

Recessed or closet installation - Dryer on pedestal

olo

0"-,+*- 27"- F-0"

{0 cm) (68.6 cm) {0 cm}

A. Recessed area B. Side view - closet or confined area

*Side or bottom venting

Minimum installation spacing for cabinet installation

0"I1_- 81½"--_10"*1

(0cm) (60cm) (0cm)

_t3_E

(7.6cm)

3"(7.8cm)

24 in?*

_ _ 1"(2.8cm)

(185cm_)

•Min. topand bottom air openings for closet doo_

6" {18.2 ore)

76"

{193 cm) -- --

5½"**

(14 cm)

** External exhaust elbow requires additional

spacing.

*** Wall, door and floor molding may require

additional spacing.

1"*** _ _-27"-_

{2=5cm) 68=6 crrl

1''***

2,5cm

The dimensions shown are for the minimum spacing allowed. For cabinet installation, with a door, minimum ventilation

openings in the top of the cabinet are required.

m)" . 7"(17.8cm)

(22 9 cm)

0 31% O

(0 cm) (80.0 cm) (0 cm) (0 cm) (68.6 cm) (0 cm)

Mobile home - Additional installation requirements This dryer is suitable for mobile home installations. The install-

ation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal

Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH.

Mobile home installations require:

• Metal exhaust system hardware, which is available for purchase from your dealer.

Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer

exhaust opening.

It is your responsibility

• Tocontact a qualified electrical installer.

• To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSl/NFPA

70-latest edition and all local codes and ordinances. The National Electric Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect

to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit.

• Do not use an extension cord.

• If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions provided for it here.

• This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground conductor is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground conductor must be removed from the external ground connector (green screw), and secured under the neutral terminal (center or white wire) of the terminal block. When the neutral ground conductor is secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is isolated from the

neutral conductor.

• If local codes do not permit the connection of a neutral ground wire to the neutral wire, see "Optional 3-wire

connection" section. A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through the neutral is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral

conductors.

If using a power supply cord: Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

• A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned

ends.

• A UL listed strain relief.

If your outlet looks like this:

4-wire receptacle (14-30R)

Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either green or bare. The neutral conductor must be identified by a white cover.

If your outlet looks like this:

3-wire receptacle (10-30t:?)

Then choose a 3-wire power supply cord with ring or spade terminals and UL listed strain relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire: Power supply cable must match power supply (4-wire or 3-wire)

and be:

• Flexible armored cable or nonmetallic sheathed copper cable (with ground wire), protected with flexible metallic conduit. All current-carrying wires must be insulated.

• 10-gauge solid copper wire (do not use aluminum).

• At least 5 ft (1.52 m) long.

GROUND(NG (NSTRUCT(ONS

m For a grounded, cord-connected dryer: This dryer must be grounded. In the event of ma(function or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer uses a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

m For a permanently connected dryer: This dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on the dryer.

WARNING-" Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug on the power supply cord: if it wi(I not fit the outlet, have a proper outlet

(nstai(ed by a qua)ified e)ectdcian=

SAVE THESE (NSTRUOT(ONS

EmectricaI Shock Hazard

PJug into a grounded 4 prong outlet. Failure to do so can resuJt in death or emectricaI shock.

It is your responsibility

• Tocontact a qualified electrical installer.

To be sure that the electrical connection is adequate and in conformance with the Canadian Electrical Code, C22.1 -latest

edition and all local codes. A copy of the above codes standard may be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3

CANADA. To supply the required 4 wire, single phase, 115/230 volt,

60 Hz., AC only electrical supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or

circuit breaker is recommended. Connect to an individual branch circuit.

This dryer is equipped with a CSA International Certified Power Cord intended to be plugged into a standard 14-30R wall receptacle. The cord is 5 ft (1.52 m) in length. Be sure wall receptacle is within reach of dryer's final location.

• Do not use an extension cord.

If using a replacement power supply cord, it is recommended that you use Power Supply Cord Replacement Part Number

9831317. For further information, please reference the service

numbers located in the "Assistance or Service" section of this manual.

GROUNDING iNSTRUCTiONS

m For a grounded, cord-connected dryer: This dryer must be grounded, in the event of maJfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment- grounding conductor and a grounding plug. The plug must be piugged into an appropriate outlet that is properJy instalJed and grounded in accordance with all Jocal codes

and ordinances. WARNING-" improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a quaJified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed

by a qualified ebctrJcian.

SAVE THESE iNSTRUCTiONS

4-wire receptacle 14-30R

Power Supply Cord Direct Wire

Fire Hazard

Use a new UL listed 30 amp power supply cord. Use a UL _isted strain retief,

Disconnect power before making e_ectrical connections. Connect neutra_ wire (white or center wire) to center

terminal (silver),

Ground wire (green or bare wire) must be connected to green ground connector.

Connect remaining 2 supply wires to remaining 2 terminals (go_d).

Securely tighten aimelectrica_ connections, Failure to do so can result in death, fire, or

e_ectrical shock,

1. Disconnect power.

2. Remove the hold-down screw and terminal block cover.

Fire Hazard

Use 10 gauge solid copper wire, Use a UL listed strain relief,

Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (silver).

Ground wire (green or bare wire) must be connected to green ground connector,

Connect remaining 2 supply wires to remaining 2 terminals (gold).

Securety tighten a_lelectrica{ connections. Failure to do so can result in death, fire, or

electrical shock.

Install strain relief. Style 1: Power supply cord strain relief

Remove the screws from a %" (1.9 cm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections into the hole below the terminal block opening so that one tab is pointing up and the other is pointing down, and hold in place. Tighten strain relief screws just enough to hold the two clamp sections together.

A. Neutral ground wire B. External ground conductor screw

C. Center, silver-colored terminal block screw D. Terminal block cover and hold-down screw

A. Strain relief tab pointing up B. Hole below terminal block opening C. Clamp section D. Strain relief tab pointing down

Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have atight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point.

Style 2: Direct wire strain relief

Unscrew the removable conduit connector and any screws from a %" (1.9 cm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the hole below the terminal block opening. Reaching inside the terminal block opening,

screw the removable conduit connector onto the strain relief threads.

Electrical Connection Options

If your home has: And you will be Go to Section

connecting to:

4-wire receptacle A UL listed, 4-wire connection: (NEMA Type 14-30R) 120/240-volt Power supply cord

30-amp, dryer power supply

minimum, cord*

4-wire direct A fused 4-wire connection:

disconnect or Direct Wire circuit breaker box*

(12.7 cm)

3-wire receptacle A UL listed, (NEMA type 10-30R) 120/240-volt

3-wire connection:

Power supply cord

30-amp, dryer power supply

minimum, cord*

3-wire direct A fused 3-wire connection:

disconnect or Direct Wire circuit breaker box*

A. Removable conduit connector B. Hole below terminal block opening

C. Strain relief threads

Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against

the direct wire cable.

*If local codes do not permit the connection of a frame-grounding

conductor to the neutral wire, go to "Optional 3-wire connection" section.

4-wire connection: Power supply cord

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire connections.

A ....

B F

C D E G

A.4-wire receptacle (NEMA type 14-30R) B.4-prong plug

C. Groundprong D.Neutral prong

E.Spade terminals with upturned ends F:3_,,(1.9cm) UL listed strain relief

G.Ring terminals

Now complete installation following instructions for your type of electrical connection:

4-wire (recommended)

3-wire (if 4-wire is not available

Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord under center, silver-colored terminal block screw. Tighten screw.

..... J-- C

......................._ C:::u::::...............)--

s .............\\ ................o

A. External ground conductor screw - Dotted line shows

position of NEUTRAL ground wire before being moved to

center silver-colored terminal block screw

B. Center silver-colored terminal block screw

C. Neutral ground wire

D. Neutral wire (white or center wire) E. 3/4"(1.9 cm) UL Iisted strain relief

Connect ground wire (green or bare) of power supply cord to external ground conductor screw. Tighten screw.

4-wire connection: Direct wire

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire connections.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.

Strip 5" (12.7 cm) of outer covering from end of cable, leaving bare ground wire at 5" (12.7 cm). Cut 11/2'' (3.8 cm) from 3 remaining wires. Strip insulation back 1" (2.5 cm). Shape ends of wires into a hook shape.

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown.

A. External ground conductor screw B. Ground wire (green or bare) of power supply cord C. _" (1.9 cm) UL listed strain relief

D. Center silver-colored terminal block screw

E.Neutral ground wire

E Neutral wire (white or center wire)

4. Connect the other wires to outer terminal block screws. Tighten screws.

5. Tighten strain relief screws.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

7. You have completed your electrical connection. Now go to "Venting Requirements."

Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and place the hooked end hook facing right) of the neutral wire (white or center wire) of direct wire cable under the center screw of the

terminal block. Squeeze hooked ends together. Tighten screw.

A _,................

A. External ground conductor screw - Dotted line shows

position of NEUTRAL ground wire before being moved to

center silver-colored terminal block screw

B. Center silver-colored terminal block screw

C. Neutral ground wire D. Neutral wire (white or center wire)

E. 3/4"(1.9 cm) UL listed strain relief

Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw.

C ¸¸

A. External ground conductor screw B. Ground wire (green or bare) of power supply cord

C. 3/4"(1.9 cm) UL listed strain relief D. Center silver-colored terminal block screw

E, Neutral ground wire

F Neutral wire (white or center wire)

Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

!! !!

Loosen or remove center silver-colored terminal block screw.

Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the terminal block. Tighten screw.

A. Externalground conductor screw

B.Neutral ground wire

C. Centersilver-colored terminal block screw D. Neutral wire (white orcenter wire)

E._" (1.9cm) UL Iisted strain relief

3. Connect the other wires to outer terminal block screws. Tighten screws.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

6. You have completed your electrical connection. Now go to "Venting Requirements."

5. Tighten strain relief screw.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

7. You have completed your electrical connection. Now go to "Venting Requirements."

3-wire connection: Power supply cord

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

B D E

A. 3-wire receptacle (NEMA type 10-30R)

B. 3-wire plug C. Ground prong D. Spade terminals with up turned ends E. _" (1.9 cm) UL Iisted strain relief

E Ring terminals

G. Neutral (white or center wire)

3-wire connection: Direct wire

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.

Strip 31/2'' (8.9 cm) of outer covering from end of cable. Strip insulation back 1" (2.5 cm). If using 3-wire cable with ground wire, cut bare wire even with outer covering. Shape ends of wires into a hook shape.

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw, as shown.

Loosen or remove center silver-colored terminal block screw.

Place the hooked end of the neutral wire (white or center wire) of direct wire cable under the center screw of terminal block

(hook facing right). Squeeze hooked end together. Tighten screw,

A. External ground conductor screw B. Neutral ground wire

C. Center silver-colored terminal block screw D. Neutral wire (white or center wire)

E. _" (1.9 cm) UL listed strain relief

Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

Optional 3-wire connection

Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire.

1. Remove center silver-colored terminal block screw.

2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord/cable under center, silver-colored terminal block screw. Tighten screw.

!! !!

4. Tighten strain relief screw.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

6. You have completed your electrical connection. Now go to "Venting Requirements."

A. External ground conductor screw

B. Center silver-colored terminal block screw C. Neutral ground wire

D. Neutral wire (white or center wire) E. _" (1.9 cm) UL listed strain relief

F Grounding path determined by a qualified electrician

Connect the other wires to outer terminal block screws. Tighten screws.

!! !!

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

6. Connect a separate copper ground wire from the external ground conductor screw to an adequate ground.

Fire Hazard Use a heavy metam vent, Do not use a pmastic vent,

Do not use a metal feiB vent. Failure to follow these }nstruct}one can resumt }n death

or fire,

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS, IMPORTANT: Observe all governing codes and ordinances,

The dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, or a concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint,

• Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

• Review Vent system chart. Modify existing vent system if necessary to achieve the best drying performance.

• Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance.

• Do not install flexible metal vent in enclosed walls, ceilings or floors.

Elbows

45° elbows provide better airflow than 90° elbows.

J /

Good Better

Clamps

• Use clamps to seal all joints.

• Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the

duct. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be used, DURASAFE TM venting products are recommended.

4" (!0.2 cm) heavymetal exhaust vent

DURASAFE TM vent products can be purchased from your dealer or by calling Whirlpool Parts and Accessories. For

more information, see the "Assistance or Service" section of this manual.

Rigid metal vent

• For best drying performance, rigid metal vents are recommended.

• Rigid metal vent is recommended to prevent crushing and kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for cleaning.

• Flexible metal vent must be fully extended and supported when the dryer is in its final position.

(10_2cm)

A. Louvered hood style

B.Box hood style

The angled hood style (shown here) is acceptable.

(6_4 cm)

An exhaust hood should cap the vent to prevent rodents and insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).

• Do not use an exhaust hood with a magnetic latch.

_mproper venting can cause moisture and mintto collect indoors, which may reeumt in:

[] Moisture damage to woodwork, furniture, paint,

wallpaper, carpets, etc=

[] Housecleaning problems and health problems.

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer.

Other installations are possible.

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown.

Refer to the manufacturer's instructions.

A ..........

E F

A. Dryer E. Clamps B. Elbow F. Rigid metal or flexible metal vent

C. Wall G. Vent length necessary to connect D. Exhaust hood elbows

H. Exhaust outlet

Optional exhaust installations

This dryer can be converted to exhaust out the right side, left

side, or through the bottom. If you prefer, you may contact your local dealer to have the dryer converted.

Fire Hazard

Cover unused exhaust holes with one of the

following kits:

279818 (white) 280028 (meteorite}

Contact your _ocat dealer. Failure to follow these instructions can result in death,

fire, e_ectrical shock, or serious injury.

A B

A. Over-the-top installation (also available with one

offset elbow)

B. Periscope installation

NOTE: The following kits for close clearance alternate installations are available for purchase. Please see the

"Assistance or Service" section of this manual to order.

• Over-the-Top Installation: Part Number 4396028

• Periscope Installation (For use with dryer vent to wall vent mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)

mismatch Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)

mismatch

Special provisions for mobile home installations The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside.

A B C

A. Standard rear offset exhaust installation B. Left or right side exhaust installation

C. Bottom exhaust installation

Determine vent path

• Select the route that will provide the straightest and most direct path outdoors.

• Plan the installation to use the fewest number of elbows and turns.

• When using elbows or making turns, allow as much room as possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90° turns possible.

Determine vent length and elbows needed for best drying performance

• Use the Vent system chart below to determine type of vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that will

help to achieve the best drying performance.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add one 90° turn to the chart.

1. To protect the floor, use a large flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer.

2. Firmly grasp the body of the dryer (not the console panel). Gently lay the dryer on the cardboard. See illustration.

Number of Type of Box or Angled

90° turns vent Iouvered hoods or elbows hoods

0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)

Flexible metal 36 ft (11 m) 28 ft (8.5 m)

1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m)

Flexible metal 27 ft (8.2 m) 19 ft (5.8 m)

3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)

Flexible metal 25 ft (7.6 m) 17 ft (5.2 m)

4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m)

Flexible metal 23 ft (7 m) 15 ft (4.6 m)

Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.

Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in "Plan Vent System." Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior

of the vent to secure vent.

i \\ i \\ i \\ i \\ [ \\

i \\\

Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer

visible.

5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the

dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into its final position. Do not crush or kink vent.

3. (On gas models) Check to be sure there are no kinks in the flexible gas line.

4. Once the exhaust vent connection is made, remove the corner posts and cardboard.

Check the levelness of the dryer. Check levelness first side to side, then front to back.

4. Remove the 6 screws to release the outer door assembly from the inner door assembly (see illustration). It is important that you remove only the 6 indicated screws.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for

levelness.

You can change your door swing from a right-side opening to a left-side opening, if desired.

Remove the door

1. Open the dryer door. Remove the 4 screws that hold the door hinge on the front panel of the dryer. Loosen, but do not

remove, the screw with the top keyhole opening last (second from the top).

............................"' /

A. Dryer B. Do not remove

C. Dryer door

5. Lift the inner door assembly off of the outer door assembly. Unsnap the handle from the outer door assembly, move it to the other side, and snap in. Set the outer door assembly

aside.

Reverse the hinge and hinge bracket

1. Place the inner door, screw head side up, on the work surface.

2. Remove the 4 screws that hold the hinge to the door.

2. Lift and pull forward on the door so that the keyhole clears the screw head. Remove the door.

3. Lay the dryer door on a flat, protected surface with the inside door assembly facing up. Remove the last screw from Step 1. Remove the 2 screws holding the handle to the door.

3. Remove the 2 screws that hold the handle bracket to the door.

4. Move hinge to the other side and reattach with the 4 screws removed in Step 2.

5. Move handle bracket to the other side and reattach with the 2 screws removed in Step 3.

6. Set the inner door assembly aside.

Reinstalling the door

1. Check for fingerprints on the glass. Clean if necessary.

2. Place the inner door assembly into the outer door assembly. Align the hinge in the opening on the side. To fit correctly, the inside door assembly edge is completely inside the outside door assembly edge.

3. Reassemble the inner and outer door assemblies with the 6 screws.

Replace the 2 handle screws for the door handle of the door assembly.

Use a small flat-blade screwdriver to remove plug strip in the door opening. Slide the head of the screwdriver under the top portion of the plug strip, being certain not to scratch the dryer surface. Lift up. Repeat in the middle and at the bottom. Remove the plug stripe in the door opening and insert in the opposite side.

Insert a screw in the second opening from the top of the hinge opening and partially tighten. Hang the door by placing the top hinge keyhole over the second screw head and

tighten the screw. By putting this screw in first, the door will hang in place while you insert and tighten the remaining 4 screws.

A. Dryer door B. Dryer

C. Insert this screw first

1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check the dryer's final location. Be sure the vent is not crushed or kinked.

5. Check that the dryer is level. See "Level Dryer."

6. In the U.S.A.

• For power supply cord installation, plug into a grounded

outlet. For direct wire installation, turn on power.

In Canada

Emectdcal Shock Hazard

Pmuginto a grounded 4 prong outlet. Failure to do so can result in death or electrical shock.

• Plug into a 4 prong grounded outlet. Turn on power.

7. Remove the blue protective film on the console and any tape remaining on the dryer.

8. Read "Dryer Use."

g. Wipe the dryer drum interior thoroughly with a damp cloth to

remove any dust.

10. Set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer.

If the dryer will not start, check the following:

• Controls are set in a running or "On" position.

• Start button has been pushed firmly.

• Dryer is plugged into a grounded outlet and/or electrical

supply is on.

• Household fuse is intact and tight, or circuit breaker has

not tripped.

• Dryer door is closed.

11.

When the dryer has been running for 5 minutes, open the dryer door and feel for heat. Ifyou feel heat, cancel cycle and

close the door. If you do not feel heat, turn off the dryer and check the

following:

• There may be 2 household fuses or circuit breakers for

the dryer. Check to make sure both fuses are intact and tight, or that both circuit breakers have not tripped. If

there is still no heat, contact a qualified technician.

NOTE: You may notice a burning odor when the dryer is first heated. This odor is common when the heating element is first used. The odor will go away.

7. Close the door and check that it latches securely.

DRYER USE

CONTROL ON _ AUTOMATIC MANUAL Estimated Time

Control locked O

Sensing O Normal Touchup

Cool Down O De_cate

Extra Care O DRY TIME

Heavy Duty Timed D_y Rema nlng

aides__CYCLes

Super

Expmosion Hazard

Keep flammabme materials and vapors, such as

gasomine, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing). Failure to follow these instructions can resumt in death,

expmosion, or fire.

O Medium

I ore

DRYNESS

LEVEL

O Low

Extra Low Soft

Less

f High O1

Air Only O Off Or_

TEMP EXTRA CYCLE

CARE _ND @

Loud O

_;_GNAL HoJd for 3

seconds to

Jock / unlock Pause

controt

Fire Hazard

No washer can compmeteBy remove oil. Do not dry anything that has ever had any type of oH on

it (including cooking oils).

Items containing foam, rubber, or plastic must be dried on a cmothesmine or by using an Air Cycle.

Failure to fo[mow these instructions can resumt in death

or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

The following is a guide to starting your dryer. Please refer to

specific sections of this manual for more detailed information.

1. Clean lint screen before each load, See "Cleaning the Lint Screen."

2. Place laundry into dryer and shut door.

3. Rotate the dial to select either an Automatic or Manual Cycle then press the CONTROL ON button, The preset settings and drying time for the cycle chosen will be displayed,

To use an Automatic Cycle

Point the dial to an Automatic Cycle. Select DRYNESS LEVEL to adjust how dry you want the

load to be. The time displayed is an estimated length of the cycle based on the Dryness Level selected. As the cycle runs, the control senses the dryness of the load and adjusts the time automatically for the selected Dryness

Level.

Less

I More

DRYNESS

LEVEL

NOTE: Time is not adjustable for Automatic Cycles. Pressing the Manual Dry Time (- or +) buttons will cause a triple beep, indicating that the time cannot be changed.

• Press the EXTRA CARE feature button if this option is desi red.

Press the CYCLE END SIGNAL button to set signal volume to desired level.

Press (and hold) HOLD TO START button until dryer starts (about 1 second).

Once an Automatic cycle has started, the Extra Care feature and the Cycle End Signal level can be adjusted. Press the OFF button twice to stop the dryer and clear the settings, allowing you to select another cycle and Dryness Level.

How Auto Moisture Sensing Plus works

The Even-Heat TM feature improves drying performance with Auto Moisture Sensing Plus, which advances the cycle as moisture is extracted from clothing. A thermistor (electronic temperature sensor) and moisture sensing strips in the dryer drum help measure the amount of moisture in the clothes as they pass. An electronic control determines the load type to help save time, prevent overdrying, and increase the accuracy of the end dryness level. After the first 5 minutes of an automatic cycle, the estimated time display will adjust based on the approximate load size, cycle, dryness level

selected and amount of moisture left in the clothes. When the clothes have reached approximately 80% of the dryness level

selected, the estimated time display will adjust again, showing the final drying time. Auto Moisture Sensing Plus takes the guesswork out of drying time and enhances fabric

care.

To use a Manual Cycle

• Rotate the dial to select a Manual Cycle. Press MANUAL DRY TIME (- or +) buttons until the desired

drying time is displayed. Tap - or + and the time will change by 1-minute intervals. Press and hold - or + and the time will change by 5-minute intervals. The initial time displayed is the actual drying time.

NOTE: The Manual Dry Time feature can be used only with Manual Cycles.

• Press TEMP until the desired temperature glows. NOTE: Pressing the Dryness Level button will cause the triple

beep indicating that this option is not selectable. Also, a Dryness Level is not indicated.

• Press the EXTRA CARE feature button if this option is desired.

• Press the CYCLE END SIGNAL button to set volume to desired level.

• Press (and hold) HOLD TO START button until dryer starts (about 1 second).

While a Manual Cycle is running, you can change the settings for Time, Temperature, the Extra Care feature, and the Cycle

End Signal. Press the OFF button twice to stop the dryer and clear the settings, allowing you to select another cycle.

To stop your dryer at any time Press OFF twice or open the door.

To pause the dryer at any time Open the door or press OFF once.

To restart the dryer Close the door and press (and hold) HOLD TO START button until

dryer starts. NOTE: Drying will continue from where the cycle was interrupted

if you close the door and press Start within 5 minutes. Ifthe cycle is interrupted for more than 5 minutes, the dryer will shut off. Select new cycle settings before restarting the dryer.

This feature allows you to lock your settings to prevent unintended use of the dryer. You can also use the Control Locked feature to prevent unintended cycle or option changes during dryer operation.

To enable the Control Locked feature when dryer is

running:

Press and hold the CYCLE END SIGNAL button for 3 seconds. The control is locked when a single beep is heard and the Control

Locked status light is on.

• When the dryer is off, it is not necessary to press the Control On button before activating the Control Locked feature.

To unlock:

Press and hold the CYCLE END SIGNAL button for 3 seconds to turn this feature off.

NOTE: When the dryer is running and Control Locked is on, the dryer can be stopped by pressing the Off button, but can't be

restarted until the control is unlocked.

Select the correct cycle and dryness level or temperature for your load. If an Automatic Cycle is running, the display shows the estimated cycle time when your dryer is automatically sensing

the dryness level of your load. If a Manual Cycle is running, the display shows the exact number of minutes remaining in the

cycle. Cool Down tumbles the load without heat during the last few

minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level.

Drying tips

• Follow care label directions when they are available.

• If desired, add a fabric softener sheet. Follow package instructions.

• Remove the load from the dryer as soon as tumbling stops to reduce wrinkling. This is especially important for permanent press, knits, and synthetic fabrics.

• Avoid drying heavy work clothes with lighter fabrics. This could cause overdrying of lighter fabrics, leading to increased shrinking or wrinkling.

Cycle tips

• Dry most loads using the preset cycle settings.

• Refer to the Automatic or Manual Preset Cycle Settings chart (in the "Cycles" section) for a guide to drying various loads.

Drying temperature and Dryness Level are preset when you choose an Automatic Cycle. You can choose a different dryness level, depending on your load by pressing the DRYNESS LEVEL button to select MORE or

LESS.

• If you wish to adjust the cycle length of a Manual Cycle,

you must press the MANUAL DRY TIME (- or +) buttons. Adjust the temperature of a Manual Cycle by pressing TEMP until the desired temperature is selected.

NOTE: You cannot choose a Dryness Level with Manual Cycles.

You may follow the progress of your dryer with the drying status indicator lights.

Sensing O

Wet 0

Damp O

Coo[ Down O

Cyde CompUete O

Extra Care O

Contro[ Locked O

Sensing

When a cycle is first turned on, the Sensing light glows until a wet item is detected.

• In an Automatic cycle, if a wet item has not been detected within 10 minutes, the Sensing light will turn off and the dryer

will shut down.

• In a Manual cycle, if a wet item is not detected after 10 minutes the Wet light turns on and the selected cycle

continues.

Select the drying cycle that matches the type of load you are drying. See Automatic preset or Manual preset cycle settings

charts.

AUTOMATIC

Heavy Duty

MANUAL

Timed Dry

Touchup

coE;r\o'

_ Rapid Dry

Super

Delicate "_

Cycle control knob

Automatic Cycles allow you to match the cycle to the load you are drying. See the following Automatic preset cycle settings chart. Each cycle dries certain fabrics at the recommended temperature. A sensor detects the moisture in the load and automatically adjusts the drying time for optimal drying.

Wet The Wet light will turn on when a wet item has been detected in

the dryer. The Wet light will remain on until:

• The damp dry point is reached in an Automatic cycle.

• The dryer enters the cool down period in a Manual cycle.

Damp

The Damp light indicates that the load has reached the damp dry

level. NOTE: The Damp light is not used with manual cycles.

Cool Down

The Cool Down light glows during the cool down part of the

cycle. Laundry is cooling down for ease in handling.

Cycle Complete

The Cycle Complete light glows when a drying cycle is finished. If the Extra Care feature has been selected, the Extra Care feature

indicator light will also be on.

The Cycle Complete light turns off 1 hour after the end of a drying

cycle (including the Extra Care cycle of 2 hours), when Off is pressed, or when the door is opened.

Extra Care Feature

The Extra Care feature light glows when this option is selected. This indicator stays on with the Cycle Complete light.

Heavy Duty

Use this cycle to get High heat for heavy fabrics such as cotton towels or bedspreads.

Normal

Use this cycle to get Medium heat for drying sturdy fabrics such as work clothes.

Casual Use this cycle to get Medium heat for drying no-iron fabrics such

as sport shirts, casual business clothes and permanent press blends.

Delicate

Use this cycle to get Low heat for drying synthetic fabrics, washable knit fabrics and no-iron finishes.

Super Delicate Use this cycle to get Extra Low heat to gently dry items such as

lingerie, exercise wear or sheer curtains.

Control Locked

The Control Locked light glows when this option is enabled.

Indicator lights

Other indicator lights on the control panel show Cycle,

Temperature, and Cycle End Signal settings selected. The time display will indicate the estimated or actual time

remaining in a cycle.

Automatic preset cycle settings

Automatic Cycles Temp. Time*

Load Type (Minutes)

HEAVY DUTY High 40

Heavyweight, towels

NORMAL Medium 34 Corduroys, work clothes

CASUAL Medium 36 Permanent press, synthetics

DELICATE Low 28 Lingerie, blouses, washable

woolens

SUPER DELICATE Extra Low 22

Exercise wear, sheer curtains, lace

*Estimated Time with Dryness Level (medium) setting.

Use Manual Cycles to select a specific amount of drying time and a drying temperature. When a Manual Cycle is selected, the ESTIMATED TIME REMAINING display shows the actual time remaining in your cycle. You can change the actual time in the cycle by pressing the Manual Dry Time (- or +) buttons.

Timed Dry

Use this cycle to complete drying if items are still damp after an

Automatic Cycle. Timed Dry is also useful for drying heavyweight

and bulky items, such as bedspreads and work clothes.

Touchup

Use this setting to help smooth out wrinkles from items such as clothes packed in a suitcase or items wrinkled from being left in

the dryer too long.

Rapid Dry

Use this cycle for drying small loads or loads that need a short drying time.

Manual preset cycle settings

Manual Cycles Temp. Default Time Load Type (Minutes)

TIMED DRY High 40

Heavyweight, bulk,

bedspreads, work clothes

Extra Care Feature When you are unable to remove a load of clothes from the dryer

as soon as it stops, wrinkles can form. The Extra Care feature periodically tumbles, rearranges and fluffs the load to help reduce wrinkling.

• Press the Extra Care feature to get up to 120 minutes of heat- free, periodic tumbling at the end of a cycle.

• Stop at any time by pressing the Extra Care feature or opening the dryer door.

For the Casual Cycle, the Extra Care feature is preset to "On." The other Automatic Cycles will retain the Extra Care feature setting. (For example, if you select the Extra Care feature in the Normal cycle, the Extra Care feature will be on the next time you select the Normal cycle.)

NOTE: Ifyou do not select the Extra Care feature, the dryer stops after the cool down period.

Temperature Temperature settings are used with the Manual Cycles. Press

TEMP until the desired temperature setting glows. Temperature settings cannot be used with the Automatic Cycles.

O Medium

Low Extra Low

I High

Air Only

TEMP

Air Only

Use the Air Only setting for items that require drying without heat such as rubber, plastic and heat-sensitive fabrics. This chart shows examples of items that can be dried using Air Only.

Type of Load Time*

(Minutes)

Foam rubber - pillows, padded bras, 20 - 30 stuffed toys

Plastic - Shower curtains, tablecloths 20 - 30

Rubber-backed rugs 40 - 50

TOUCHUP Medium 20

Helps to smooth out

wrinkles

RAPID DRY High 27

Small loads

Olefin, polypropylene, sheer nylon 10 - 20

*Reset time to complete drying, if needed.

When using Air Only

• Check to see that coverings are securely stitched.

• Shake and fluff pillows by hand periodically during the cycle.

• Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Automatic Cycles are not available when using the Air Only setting.

Cycle End Signal

The Cycle End Signal produces an audible sound when the

drying cycle is finished. Promptly removing clothes at the end of

the cycle reduces wrinkling.

Soft

Off

Loud 1

CYCLE

END

SIGNAL

HoJd for 3

seconds to

Jock / unlock

control

Press and release the CYCLE END SIGNAL to adjust the sound level or turn off the signal.

NOTE: When the Extra Care feature is selected and the Cycle End Signal is on, an audible sound will emit every 5 minutes until

the clothes are removed, or the Extra Care feature is finished.

The drying rack is useful for drying items you would not

necessarily want to tumble dry or that you would normally line dry (for example, sweaters).

To use the drying rack

Do not remove the lint screen.

1. Open dryer door.

3. Put the wet items on top of the rack. Leave space between the items so air can reach all the surfaces.

NOTE: Do not allow items to hang over the edge of the rack.

4. Close the door.

5. Select a timed drying cycle and temperature, or an air cycle (see following chart). Items containing foam, rubber or plastic

must be dried on a clothesline or by using the Air Only temperature setting.

6. You must select a time by pressing the MANUAL DRY TIME (- or +) buttons. Reset time as needed to complete drying.

Refer to the following table.

7. Press (and hold) HOLD TO START button (about 1 second).

NOTE: You must remove rack for normal tumbling. Do not use automatic cycles with the drying rack.

This chart shows examples of items that can be rack dried and the suggested cycle, temperature setting and drying time. Actual

drying time will depend on the amount of moisture items hold.

Rack Dry Setting Temp. Time*

Wool Sweaters Timed Low 60

Block to shape and lay flat on Dry the rack

A. Front edge

2. Place drying rack inside dryer drum, positioning the back wire on the ledge of the inner dryer back panel. Push down on front edge of drying rack to secure over the lint screen.

.j/

A. Dryer backpanel

Stuffed toys or pillows Timed Low 60 Cotton or polyester fiber filled Dry

Stuffed toys or pillows Timed Air Only 90 Foam rubber filled Dry (no

heat)

Sneakers or canvas shoes Timed Air Only 90

Dry (no

heat)

*(Minutes) Reset time to complete drying, if needed.

+ 53 hidden pages