KitchenAid YKEYS710LQ0, YKEHS01PWH2, YKEHS01PWH1, YKEHS01PMT2, YKEHS01PMT1 Owner’s Manual

...

KitchenAid ®

FRONT-LOADING ELECTRIC DRYER

Use & Care Guide

For questions about features, operation/performance, parts accessories or service, call: 1-800-422-1230

In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...

www.kitchenaid.com or www.KitchenAid.ca

SECADORA ELI_CIRICA DE CARGA FRONTAL

Manual de Uso y Cuidado

Si tiene preguntas respecto a las caractertsticas, funcionamiento/rendimiento, partes, accesorios o servicio t6cnico, Ilame al: 1-800-422-1230

Para la instalaci6n y el servicio t6cnico Ilame al: 1-800-807-6777 o visite nuestro sitioweb en... www.kitchenaid.com

S]_CHEUSE ]_LECIRIQUE )_ CHARGEMENT

)_ L'AVANT

Guide d'utilisation et d'entretien

Au Canada, pour assistance composez le 1-800-461-5681, pour installation ou service composez le 1-800-807-6777

ou visitez notre site web 6... www.KitchenAid.ca

Table of Contents/[ndice/Table des mati6res ............................................................... 2-3

Models/Modelos/Mod_les KEHS01 P, YKEHS01 P

8557328A

TABLEOF CONTENTS

INDICE

DRYER SAFETY ...................................................... 4

INSTALLATION INSTRUCTIONS ................................... 5

Tools and Parts ............................................................................ 5

Options ............................................................. 5

Location Requirements ............................................................... 5

Electrical Requirements- U.S.A. Only........................................ 7

Electrical Requirements - Canada Only... ................................... 8

ElectricalConnection - U.S.A. Only............................................. 9

Venting Requirements ............................................. 13

PlanVent System .................................................. 14

InstallVent System................................................. 15

Install Leveling Legs............................................... 15

Level Dryer ......................................................... 16

Connect Vent. ..................................................... 16

Reverse Door Swing .............................................. 16

Complete Installation ............................................. 17

DRYER USE ......................................................... 18

Starting Your Dryer................................................. 18

Stopping Your Dryer .............................................. 19

Pausing or Restarting ............................................. lg

Control Locked. ................................................... 19

Loading............................................................. 19

Drying and Cycle Tips ............................................. 19

Status Lights .............................................................................. 20

Cycles ............................................................. 20

Additional Features ............................................... .21

Drying Rack ....................................................... .22

DRYER CARE ...................................................... 23

Cleaning the Dryer Location ..................................... .23

Cleaning the Lint Screen .......................................... 23

Cleaning the Dryer Interior ........................................ 23

Removing Accumulated Lint..................................... .23

Vacation and Moving Care......................................................... 23

Changing the Drum LighL......................................................... 24

TROUBLESHOOTING .............................................. 24

ASSISTANCE OR SERVICE ......................................................... 25

Inthe U.S.A. ....................................................... 25

In Canada ......................................................... .25

WARRAN'rY ......................................................... 26

BEGURIDAD DE LA SECADORA .................................. 27

INSTRUCCIONEB DE INBTALACION ............................. 28

Herramientes y piezes ............................................ .28

Opciones .......................................................... .28

Requisitos de ubicacibn .......................................... .28

Requisitos el6ctricos - EE. UU. ................................... .30

Conexibn al6ctrica - Sblo en EE. UU. ........................... .32

Requisitos de ventilacibn ......................................... .36

Planificaci6n del alstema de ventilacibn ................................... .36

Instalaci6n del alstema de ventilaci6n ....................................... 38

Instalaci6n de les pates nivaladores ......................................... .38

Nivelaci6n de la escadora ........................................ .39

Conexibn dal ducto de escape ................................... .39

Cbmo invertir el cierre de la puerta ............................... .39

Complete la instalacibn ........................................... .40

UBO DE LA BECADORA ............................................ 41

Puesta en marcha de la secadora ............................... _41

Detenci6n de la marcha de la escadora ................................... _42

Pausa o resnudaci6n de la marcha .............................. _42

Control bloquesdo ............................................... _42

Cbmo cargar ....................................................... A2

Sugerencies de ciclos y secado .................................. _42

Luces de estado .................................................... 43

Ciclos. ........................................................................................ _43

Caracter[sticas adicionales ....................................... _44

Estante de secado. ................................................ _45

CUIDADO DE LA SECADORA ..................................... 46

Limpieza del lugar donde est& la escadora .............................. _46

Limpieza del filtro de palusa ...................................... _46

Limpieza del interior de la escadora ............................. _47

Eliminacibn de pelues acumulada ............................... _47

Cuidado para lesvacaciones y la mudanza ............................. A7

Cembio de la luz dal tambor ..................................... _47

SOLUCION DE PROBLEMAB ...................................... 48

AYUDA O SERVlCIO TECNICO ................................................... 49

GARANT[A. .......................................................... 50

TABLE DES MATIERES

SECURITE DE LA SECHEUSE .................................................... 51

INSTRUCTIONS D'INSTALLATION ............................................ 52

Outillage et pi6ces n6cesesires ................................................. 52

Options ....................................................................................... 52

Emplacement d'installstion........................................................ 52

Sp_ciflcstions 61ectriques- Canada esulemant ........................ 54

Exigances concernant I'_vacustion ........................................... 55

Planiflcationdu syst6me d'6vacuation ...................................... 56

Installation du conduit d'_vacuation .......................................... 57

Installation des pieds de nivellement......................................... 58

Miss & niveau de la s6cheues .................................................... 58

Conduit d'6vacuation ................................................................. 58

Inversionde I'ouverturs de la porte ........................................... 58

Achevsr I'installation .................................................................. 60

UTILISATION DE LA SECHEUSE ................................................ 61

Miss en marche de la s6cheues ................................................ 61

Arr_t de la s6cheues .................................................................. 62

Arr_t ou remies an marche......................................................... 62

Verrouillage des commandes .................................................... 62

Chargement ................................................................................ 62

Conesils pour le s6chage et lesprograrnmes ........................... 63

T&moins luminet_ ...................................................................... 63

Prograrnmes............................................................................... 64

Caract6ristiques suppl6mantaires ............................................. 65

Grille de s6chage ........................................................................ 66

ENTRETIEN DE LA SECHEUSE ................................................. 67

Nsttoyage de I'emplanemant de la s6cheues ........................... 67

Nsttoyage du filtre & charpie...................................................... 67

Nsttoyage de I'int6rieur de las6cheues .................................... 68

Rstrait de la charpie accumul6e ................................................ 68

Precautions _ prendre pour lesvanances et avant

un d_rn6nagemant ..................................................................... 68

Changement de I'ampoule d'6clairage du tambour .................. 68

DEPANNAGE ................................................................................ 69

ASSISTANCE OU SERVICE ......................................................... 70

GARANTIE ..................................................................................... 71

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurtyou and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or serlousty Injured If you don't Immedlatel_ follow Instructions.

You can be killed or seriously Injured If you don't follow Instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reducethe riskoffire, electricshock,orinjuryto personswhen usingthe dryer,follow basicprecautions,

including the following:

• Read all instructions before using the dryer.

• Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

• Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-

cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

• Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

• Before the dryer is removed from service or discarded, remove the door to the drying compartment.

• Do not reach into the dryer ifthe drum is moving.

• Do not install or store the dryer where it will be exposed

to the weather.

• Do not tamper with controls.

SAVE THESE INSTRUCTIONS

• Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended inthis

Use and Care Guide or inpublished user-repair instructions that you understand and have the skillsto

carry out.

• Do not use fabric eoftaners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

• Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

• Clean lint screen before or after each load.

• Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust,

and dirt.

• The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

• See installation instructions for grounding requirements.

INSTALLATION INSTRUCTIONS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the safety instructions provided with any tools

listed here.

Flat-blade screwdriver

Adjustable wrench that

opens to 1" (2.5 cm) or hex-head socket wrench

(for adjusting dryer feet)

Level

Wire stripper (direct wire

installations)

Parts supplied Remove parts packages from dryer drum. Check that all parts are

included.

4 Levelinglegs

NOTE: Do not use leveling legs if installingthe dryer on a

pedestal.

Parts needed

Check local codes. Check existing electrical supply and venting. See "Electrical Requirements" and "Venting Requirements" before purchasing parts.

a For close-clearance installations between 31.5" (80.01 am)

and 37" (93.98 ca), see "Plan Vent System" section for venting requirements.

= #2 Phillips screwdriver a Vent clamps

a Caulking gun and

compound (for installing new exhaust vent)

a Tin snips (new vent

installations)

= 1A"nut driver

Op_on8

Pedestal

Are you placing the dryer on a pedestal? You may purchase a pedestal separately for this dryer. This pedestal will add about

13" (33 cm) to the height of your unit for a total height of

approximately 51" (130 cm).

Optional pedestal

To order, call the dealer from whom you purchased your dryer or refer to the "Assistance or Service" section of this manual. Ask

for Part Number LAB270OPMT (Meteorite) or LAB2700MQO

(White).

Stack lot

Are you planning to stack your washer and dryer? To do so, you will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your dryer or refer to the "Assistance or Service" section of this manual. Ask

for Part Number 8541503.

Location Requirements

I_ 37" _,-I

(93.98 cm)

Mobile home installations require metal exhaust system hardware

available for purchase from the dealer from whom you purchased your dryer. Forfurther information, please refer to the "Assistance

or Service" section of this manual.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer, Place dryer at least 18 Inches (46 cm) above the floor

for a garage Inafallatlon, Fallura to do so can result In death, explosion, or firs,

You will need

m A location that allows for proper exhaust installation. See

"Venting Requirements."

m A separate 30 amp circuit. m A grounded electrical outlet located within 2 ft (61 cm) of

either side of the dryer. Sea "Electrical Requirements."

= A sturdy floor to support the total dryer weight of

200 Ibs (90.7 kg). The combined weight of a companion appliance should also be considered.

= A level floor with a maximum slope of 1" (2.5 cm) under entire

dryer. If slope is greater than 1" (2.5 cm), install Extended

Dryer Feet Kit, Part Number 279810. Clothes may not tumble

properly and automatic sensor cycles may not operate correctly if dryer is not level.

= For a garage installation, you will need to place the dryer at

least 18" (46 cm) above the floor. If using a pedestal, you will need an additional 6" (15.24 cm).

Do not operate your dryer at temperatures below 45°F (7°C). At

lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.

Installation clearances

a The location must be large enough to fully open the dryer

door.

a Additional spacing should be considered for ease of

installation and servicing.

a Additional clearances might be required for wall, door and

floor moldings.

a Additional spacing of 1" (2.5 ore) on all sides of the dryer is

recommended to reduce noise transfer.

a Companion appliance spacing should also be considered.

Dryer Dimensions

Minimum installation spacing for custom undercounter installation

The dimensions shown are for the minimum spacing allowed. Custom undercounter installation - Dryer only

3B" min.

(96.52 cm)

00ml I

O" 27" O"

(Ocm)'-_(6B.8 cm)-_(O cm)

Minimum installation spacing for recessed orcloset installation, with or without a pedestal

a The dimensionsshownare forthe minimumspacingallowed,

For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

Closet installation - Dryer only

48 In.2

(310cm:Z)-

_(7.6 cm)

(130,81 cm)

(96.52 cm)

"31½"

(80 cm) 27"

.._-_ (68.6 cm)

* 4 "

Most installations require a minimum 5½ (14 cm) clearance behind the dryer for the exhaust vent with elbow. See "Venting Requirements."

24 In.2

(155 cm:Z)-

1o,,l_31½,,_1o"l

(0 cm) (B0 cm) (Ocm)

A. Side view - closet or confined area B. Closet door with vents

Recessed or closet installation - Dryer on pedestal

o" -_ _-- 27" "--_ <-o" o,,II_- 31½"-_1o"I

(0 cm) (68.6 cm) (O cm) (O cm) (90 cm) (0 cm)

A B

A. Recessed area B. Side view - closet or confined area

_- (7.6 cm)

Minimuminstallationspacingforcabinetinstallation

a The dimensions shown are for the minimum spacing allowed. a For cabinet installation, with a door, minimum ventilation

openings in the top of the cabinet are required.

7' {17,8cm)

9,,

,(22.gcm)

0" 31½" 0" 0" _" 0"

(0cm)(s0.0cm)(0cm) (0cm)(=.scm)(0cm)

Mobile home -Additional installation requirements

This dryer issuitable for mobile home installations. The install- ation must conform to the Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24,

HUD Part 280) or Standard CAN/CSA-Z240 MH.

Mobile home installations require:

m Metal exhaust system hardware which is available for

purchase from your dealer.

Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a

nearby window) should be at least twice as large as the dryer exhaust opening.

Electrical Connection

To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

a This dryer is manufactured ready to installwith a 3-wire

electrical supply connection. The green cabinet-grcunding conductor is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the green cabinet- grounding conductor must be removed from the external ground connector (green screw), and secured under the neutral terminal (center or white wire) of the terminal block. When the green cabinet-grounding conductor is secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is isolated from the neutral

conductor.

m If local codas do not permit the connection of a cabinet

ground connector to the neutral wire, see "Optional 3-wire connection" section.

m Use a 4-wire conductor cord when the dryer is installed in a

mobile home or an area where local codas do not permit grounding through the neutral.

If using a power supply cord: Use a UL listed power supply cord kit marked for use with

clothes dryers. The kitshould contain: a A UL listed 30 amp power supply cord, rated 120/240 volt

minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ringterminals or spade terminals with upturned

ends.

a A UL listed strain relief.

If your outlet looks like this:

4-wire receptacle(14-30R)

ElectricalRequirements- U.S.A. Only

It is your responsibility

m Tocontacta qualifiedelectricalinstaller,

m To be sure that the electrical connection isadequate and in

conformance with the National Electrical Code, ANSI/NFPA 70-1etast edition and all local codas and ordinances.

The National Electric Code requires a 4-wire power supply connection for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Betterymarch Park,

Quincy, MA 02269.

m To supply the required 3 or 4 wire, single phase, 120/240-volt,

60-Hz., AC-only electrical supply (or 3 or 4 wire, 120/208-volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect

to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit.

m Do net use an extension cord. m If codas permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the ground path is adequate.

Then choose a 4-wire power supply cord with ring orspade terminals and UL listed strain relief. The 4-wire power supply

cord, at least 4 ft (1.22 m) long, must have 4, 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either green orbare. The

neutral conductor must be identified by a white cover.

If your outlet looks like this:

3-wire receptacle(10-30R)

Then choose a 3-wire power supply cord with ring orspade terminals and UL listed strain relief. The 3-wire power supply

cord, at least 4 ft (1.22 m) long, must have 3, 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire: Power supply cable must match power supply (4-wire or 3-wire)

and be: a Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), protected with flexible metallic conduit. All current-carrying wires must be insulated.

= 10-gauge solid copper wire (do not use aluminum). = At least 5 ft (1.52 m) long.

GROUNDING INSTRUCTIONS

= Fora grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This dryer uses a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged

intoan appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances. = Fora permanently connected dryer:

This dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-greunding

conductor must be run with the circuitconductors and connected to the equipment-grounding terminal or lead on

the dryer.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug on the power

supply cord: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Electrical Requirements- Canada Only

m TOsupply the required 4 wire, single phase, 115/230-volt,

6O-Hz., AC-only electrical supply on a separate 30-arnp circuit, fused on both sides ofthe line. A time-delay fuse or

circuit breaker is recommended. Connect to an individual branch circuit.

= This dryer is equipped with a CSA International Certified

Power Cord intended to be plugged into a standard 14-30R

wall receptacle. The cord is5 fc(1.52 m) in length. Be sure wall receptacle is within reach of dryer's final location.

4-wire receptacle 14-30R

= Do nat use an extension cord.

If using a replacement power supply cord, it is recommended

that you use Power Supply Cord Replacement Part Number

9831317. For further information, please reference the service

numbers located inthe "Assistance or Service" section on this manual.

GROUNDING INSTRUCTIONS

= Fora grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment- grounding conductor and a grounding plug.The plug must

be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with the

dryer: if itwill not fitthe outlet, have a proper outlet installed

by a qualified electrician.

SAVE THESE INSTRUCTIONS

Electrical Shock Hazard

Plug Into a grounded 4 prong outlet. Failure to do so can result In death or electrical shock.

It is your responsibility

a Tocontacta qualifiedelectricalinstaller,

m To be sure that the electrical connection isadequate and in

conformance with the Canadian Electrical Code, C22.1-1atest edition and all local codes. A copy of the above codes standard may be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON Mgw 1R3

CANADA.

Electrical Connection- U.S.A. Only

PowerSupplyCord

Fire Hazard

Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief.

Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (sliver). Ground wire (green or bare wire) must be connected to

green ground connector. Connect remaining 2 supply wires to remaining

2 terminals (gold). Securely tighten all electrical connections.

Failure to do so can result In death, fire, or electrical shock.

Direct Wire

Fire Hazard

Use 10 gauge solid copper wire. Use a UL listed strain relief.

Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (sliver). Ground wire (green or bare wire) must be connected to

green ground connector. Connect remaining 2 supply wires to remaining

2 terminals (gold). Securely tighten all electrical connections.

Failure to do so can result In death, fire, or electrical shock.

1. Disconnect power.

2. Remove the hold-down screw and terminal block cover.

A. Neutral grounding wire (green with yellow stdpes) B. External ground conductor screw C. Center, silver-colored terminal block scraw

D. Terminal block cover and hold-down screw

Assemble a ¾" (1.9 cm) UL listed strain relief (UL marking on strain relief) into the hole below the terminal block opening. Tighten strain reliefscrews just enough to hold the two clamp sections together. Put power supply cord through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position.

Now complete installation following instructions for your type

of electrical connection: 4-wire (recommended)

3-wire (if 4-wire is not available)

Electrical Connection Options

If your homo has: And you will be Go to Section

connecting to:

4-wire receptacle A UL listed, (NEMA Type 14-30R) 120/240 volt

4-wire connection: Power supply cord

30 amp, dryer power supply

minimum,

cord*

4-wire direct A fused 4-wire connection:

disconnect or Direct Wire circuit breaker

box*

B-wire receptacle A UL listed, B-wire connection: (NEMA type 10-3OR) 120/240 volt Power supply cord

30 amp, dryer power supply

minimum,

COrd*

B-wire direct A fused B-wire connection:

disconnect or Direct Wire circuit breaker

box*

Remove center terminal block screw.

Remove neutral grounding wire (green with yellow stripes)

from external ground conductor screw. Fasten itunder center, silver-colored terminal block screw.

A. External ground conductor screw - Dotted line shows

position of NEUTRAL grounding wire before being moved to center terminal block screw

B. Center silver-colored terminal block screw C. Green/yallow wire of harness

3. Connect ground wire (green or bare) of power supply cord to

external ground conductor screw. Tighten screw.

4. Connect neutral wire (white or center wire) of power supply

cord under center screw of the terminal block.

*If local codes do not permit the connection of a frame-grounding

conductor to the neutral wire, go to "Optional B-wire Connection" section.

4-wire connection: Power supply cord

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of B-wire connections.

C D E G

A.4-wire receptacle(NEMAtype 14-30R)

B.4-prong plug C.Ground prong D.Neutralprong E.Spade terminalswith upturnedends

K _" (1.9cm) ULlisted strainrelief

G.Ring terminals

A. External ground conductor screw

B. Ground wire (green or bare) wire of power supply cord C. _" (1.9 cm) UL listed strain relief D. Center silver-colored terminal block screw

E. Neutral grounding wire (green with yellow stripes)

K Neutral wire (white or center wire)

5. Connect the other wires to outer terminal block screws.

Tighten screws.

6. Tighten strain reliefecrews.

7. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

4-wire connection: Direct wire external ground conductor screw. Tighten screw.

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire connections.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer

can be moved if needed. Strip 5" (12.7 on) of outer covering from end of cable, leaving

bare ground wire at 5" (12.7 cm). Cut 11,_'' (3.8 cro) from 3 remaining wires. Strip insulation back 1"(2.5 cm). Shape ends of wires into a hook shape.

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw. See example

below.

Remove center terminal block screw.

Remove neutral grounding wire (green with yellow stripes)

from external ground conductor screw. Fasten itunder center, silver-colored terminal block screw.

3. Connect ground wire (green or bare) of power supply cable to

A. External ground conductor screw B. Green or bare copper wire of power supply cable

C. ¾" (1.9 cm) UL /isted straln relief D. Center silver-colored terminal block screw

E. Neutral grounding wire (green with yellow stripes) I_ Neutral wire (white or center wire)

4. Piece the hooked end of the neutral wire (white wire) of power

supply cable under the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw.

5. Place the hooked ends of the other power supply cable wires

under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.

A. External ground conductor screw - Dotted line shows

position of NEUTRAL grounding wire before being moved to center terminal block screw

B. Center silver-colored terminal block screw

C. Green/yallow wire of harness

6. Tighten strain relief screws.

7. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

3-wire connection: Power supply cord 3-wire connection: Direct wire

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

C G F

A. 3-wire receptacle (NEMA type I0-30R)

B. 3-wire plug C. Neutral prong D. Spade terminals with up turned ends

E. _" (1.9 cm) UL listed strain relief K Ring terminals

G. Neu_'al (white or center wire)

Loosen or remove center terminal block screw.

Connect neutral wire (white or center wire) of power supply cord to the center, allver-colored terminal screw of the terminal block. Tighten screw.

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer

can be moved if needed. Strip 3W' (8.9 cm) of outer covering from end of cable. Strip

insulation back 1" (2.5 cm). If using3-wire cable with ground wire, cut bare wire even with outer covering. Shape ends of wires into a hook shape.

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw. See example

below.

Loosen or remove center terminal block screw.

Place the hooked end ofthe neutral wire (white or center wire)

of power supply cable under the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw.

A. External ground conductor screw

B. Neutral grounding wire (green with yellow stripes) C. Center allver-colored terminal block screw

D. Neutral wire (white or center wire) E. _" (1.9 crn) UL listed strain relief

3. Connect the other wires to outer terminal block screws.

Tighten screws.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

-D

A. E_temal ground conductor screw

B. Neutral grounding wire (green with yellow stripes) C. Center silver-colored terminal block screw

D. Neural wire (white or center wire)

E. ¾" (1.9 cm) UL listed strain relief

Place the hooked ends of the other power supply cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.

I !

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

Optional 3-wire connection Venting Requirements

Use for direct wire or power supply cord where local codes

do not permit connecting cabinot-ground conductor to neutral wire.

1. Remove center terminal block screw.

2. Remove neutral grounding wire (green with yellow stripes)

from external ground conductor screw. Connect appliance ground wire and the neutral wire (white or center wire) of power supply cord/cable under center, silver-colorad terminal block screw. Tighten screw.

3. Connect the other wires to outer terminal block screws. Tighten screws.

I !

Use a heavy metal vent. Do not use a plaatlc vent. Do not use a metal foil vent. Failure to follow these Inatructlons can result In death

or fire.

Fire Hazard

WARNING: To reduce the risk of fire, this dryer MUST BE

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

6. Connect a separate copper ground wire from the external ground conductor screw to an adequate ground.

EXHAUSTED OUTDOORS.

4" (10.2 cm) heavy metal exhaust vent and clamps must be used.

DURASAFE TM vent products are recommended. DURASAFE TM vent products can be purchased from your dealer

or by calling Whirlpool Parts and Accessories. For more information, see the "Assistance or Service" section of this manual.

• The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, or a concealed space of a building.

• Do not use an exhaust hood with a magnetic latch.

• Do not installflexible metal vent inenclosed walls, ceilings or

floors.

Use clamps to seal all joints. Exhaust vent must not be

connected or secured with screws or other fastening devices which extend into the interior of the duct. Do not use duct

tape.

IMPORTANT: Observe all governing codes and ordinances.

.__---

A. External ground conductor screw B. Neutral grounding wire (green with yellow stripes)

C. Neutral wire (white or center wire) D. Grounding path determined by a qualified electrfcian

Improper venting can cause moisture and lint to collect Indoors, which may result In:

• Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc.

• Housecleaning problems and health problems.

Use a heavy metal vent. Do not use plastic or metal foil vent. Rigid metal vent is recommended to prevent crushing and

kinking.

Flexible metal vent must be fully extended and supported when the dryer is in its final position. Remove excess flexible metal vent to avoid sagging and kinking that can result in reduced airflow and poor performance.

An exhaust hood should cap the vent to prevent rodents and insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that is in the path of the exhaust (such as flowers,

rocks or bushes, etc.).

If using an existing vent system, clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint. Replace any plastic or metal foil vent with rigid metal or

flexible metal vent.

Plan Vent System

Typical exhaust installations Typical installations vent the dryer from the rear of the dryer.

Other installstions are possible.

Alternate installations for close clearances Venting systems come in many varietiea. Select the type beat for

your installation. Two close-clearance installations are shown.

Refer to the manufacturer's instructions.

ii I i _1

A m

A. Dryer

B. Elbow

C. Wall D. Exhaust hood

E. Clamps E Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows H. Exhaust outlet

Optional exhaust installations This dryer can be converted to exhaust out the right side, left side, orthrough the bottom. Contact your local dealer to have the

dryer converted.

Fire Hazard

Cover unused exhaust holes with one of the following kits:

279818 (white) 280028 (meteorite)

Contact your local dealer. Failure to follow these Inatructlons can result In death,

fire, electrical shock, or serious Injury.

", J

A B

A. Over the top installation (also available with one

offset elbow)

B. Periscope installation

NOTE: The following kits for close clearance alternate installations are available for purchase. Please see the

"Assistance or Service" section ofthis manual to order. a Overthetop Installation:

Part Number 4396028

Periscope Installation (For use with dryer vent to wall vent

mismatch):

Part Number 4396037 - 0" ((3cm) to 18" (45.72 on)

mismatch

Part Number 4396011 - 18" (45.72 on) to 29" (73.66 cm)

mismatch

Part Number 4396014 - 29" (73.66 on) to 50" (127 cm)

mismatch

Special provisions for mobile home installations The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside.

A B C

A. Standard tear offset exhaust installation B. Left or tight side exhaust installation C. Bottom exhaust installation (Not an option with

pedestal installationsJ

Determine vent length

1. Select the route that will provide the straightest and most

direct path outdoors. Plan the installation to use the feweat number of elbows and turns. When using elbows or making turns, allow as much room as possible. Bend vent gradually to avoid kinking. Avoid 90° turns when possible.

Determine vent length.

The maximum length of the exhaust system depends upon:

• The type of vent (rigid metal or flexible metal).

• The number of elbows used.

• Type of hood.

Recommended hood styles are shown here.

Install Vent System

1. Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible.

See "Determine vent length." Avoid 90° turns. Use clamps to seal all joints. Do net use duct tape, screws or other fastening

devices that extend into the interior of the vent to secure vent.

10.2 cm

(10.2 cm)

A. Louveredhood style B. Box hood style

The angled hood style (shown following) is acceptable.

(10.2 cl

(8.4 cm)

See the exhaust vent length chart that matches your hood type for the maximum vent lengths you can use.

Exhaust systems longer than specified will:

• Shorten the life of the dryen

• Reduce performance, resulting in longer dryingtimes and

increased energy usage.

3. Determine the number of elbows you will need. IMPORTANT: Do not use vent runs longer than those

specified in the Vent Length Chart. The following chart helps you determine your maximum vent

length based on the number of 90 ° turns or elbows you will need and the type of vent (rigid or flexible metal) and hood that you will use.

Vent Length Chart

Install Leveling Legs

1. To protect the floor, use a large flat piece of cardboard from

the dryer carton. Place cardboard under the entire back edge of the dryer. See illustration.

2. Firmly gresp the body of the dryer (notthe console panel). Gently lay the dryer on the cardboard.

3. Examine the leveling legs. Find the diamond marking.

Number of Type of Box or Angled 90° turns vent Louvered hoods

or elbows hoods

O Rigid foetal 64 ft (20 m) 58 ft (17.7 m)

Flexible roetal 36 ft (11 m) 28 ft (8.5 m)

1 Rigid metal 54 ft(16.5 m) 48 ft (14.6 m)

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

2 Rigid roetal 44 ft (13.4 m) 38 ft (11.6 m)

Flexible roetal 27 ft (8.2 m) 19 ft (5.8 m)

3 Rigid roetal 35 ft (10.7 m) 29 ft (8.8 m)

Flexible roetal 25 ft (7.6 m) 17 ft (5.2 m)

4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m)

Flexible roetal 23 ft (7 m) 15 ft (4.6 m)

NOTE: Side and bottom exhaust installations have a 90 ° turn

inside the dryer. To determine maximum exhaust length, add one 90° turn to the chart.

4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs untilthe diamond marking is no longer

visible.

Place a carton corner post under each of the 2 dryer back

corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room

to connect the exhaust vent.

6. Once connection ismade and dryer is in final location, remove corner posts and cardboard.

Level Dl"yel" door assembly facing up. Remove the last screw from Step 1.

Check the levelness of the dryer. Check levelness first side to side, then front to back.

Ifthe dryer is not level, prop upthe dryer using awood block. Use a wrench to adjust the legs up or down and check again for

levelness.

NOTE: It might be necessary to levelthe dryer again after it has

been moved into its final position.

Connect Vent

1. Using a 4" (10.2 cm) clarop, connect vant to exhaust outlst in

dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into final position. Do not crush or kink vent. Make sure dryer is level.

3. (On gas models) Check to be sure there are no kinks in the

flexible gas line.

Reverse Door Swing

You can change your door swing from a right-side opening to a left-side opening, if desired.

3. Lay the dryer door on a flat, protected surface with the inside

Remove the 2 screws holding the handle to the door.

_®"

Remove the 6 screws to release the outer door assembly

from the inner door assembly (see illustration). It is important that you remove only the 6 indicated screws.

Liftthe inner door assembly off ofthe outer door sseambly. Unsnap the handle from the outer door assembly, move it to

the other side, and snap in. Set the outer door assembly aside.

Remove the door

1. Open the dryer door. Remove the 4 screws that hold the door hinge on the front panel of the dryer. Loosen, but do not remove, the screw with the top keyhole opening last (second from the top).

A. Dryer B. Do not remove

C. Dryer door

Lift and pull forward on the door sothat the keyhole clears

the screw head. Remove the door.

Reverse the hinge and hinge bracket

1. Place the inner door,screw head side up, on the work

sur_ac8.

2. Remove the 4 screws that hold the hinge to the door.

3, Remove the 2 screws that hold the handle bracket to the

door.

4. Move hinge to the other side and reettach with the 4 screws

removed in Step 2.

5. Move handle bracket to the other side and resttach with the 2 screws removed inStep 3.

6. Set the inner door assembly aside.

Insert a screw in the second opening from the top of the

hinge opening and partially tighten. Hang the door by placing the top hinge keyhole over the second screw head and tighten the screw. By putting this screw in first, the door will

hang in place while you insert and tighten the remaining 4

SCreWS.

A. Dryer door

B. Dryer

C. Insert this screw first

Reinstalling the door

1. Check for fingerpitnts on the glass. Clean if necassary.

2. Place the inner door assembly into the outer door assembly. Align the hinge inthe opening on the side. To fit correctly, the inside door assembly edge is completely inside the outside door assembly edge.

3. Reassemble the inner and outer door assemblies with the

6 SCreWS.

Replace the 2 handle screws for the door handle ofthe door

assembly.

Use a small fiet-blade screwdriver to remove hole plugs inthe door opening. Slide the head of the screwdriver under the cap of each hole plug, being careful not to scratch the dryer surface. Lift up. Remove the hole plugs inthe door opening and insert in the opposite side.

7. Close the door and check that it latches securely.

Complete Installation

1. Check to be sure all parts are now installed. If there is an

extra part, go back through the steps to see which step was skipped.

2. Check to be sure you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check the dryer's final Iocetion. Be sure the vant is not crushed or kinked.

5. Check to be sure the dryer is level. See "Level Dryer."

6. Plug into a grounded outlet. Turn power on.

7. Remove the blue protective film on the console and any tape remaining on the dryer.

8. Read "Dryer Use."

9. Wipe the dryer drum interior thoroughly with a damp cleth to remove any dust.

10. Set the dryer on a full heat cycle (net an air cycle) for 20 minutes and start the dryer.

If the dryer will not start, check the following:

• Controls are set ina running or "On" position.

• Start button has been pushed firmly.

• Dryer is plugged into a grounded outlet.

• Electrical supply is connected.

• House fuse is intact and tight, or circuit breaker has not

tripped.

• Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat.

If you do not feel heat, turn the dryer off and check the

following:

• There may be 2 fuses or circuit breakers for the dryer. Check to make sure both fuses are intact and tight, or that both circuit breakers have not tripped. If there isstill no heat, contact a qualified technician.

NOTE: You may notice a burning odor when the dryer isfirst heated. This odor is common when the heating element is first used. The odor will go away.

DRYER USE

Delicate

AUmDMA11_

Kuvy Dut_

Nmmal •

rimed D_/ Remaining O Medium

--UAL E_Umated_me I High 1

• RaNd D_ Less Air Only Off

€ONTROL ON 0

Sensing 0

_t O

Damp O

Cool Down O

Cycle Complete O

Ex_a Cam O

Corr_ol Lodged O

Starting Your Dryer

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer. Do not dry anything that has ever had anything

flammable on It (even after washing). Failure to follow these Inatructlons can result In death,

explosion, or fire.

0 _a'a Low

o o o o

_'_ME LEVEL _ END

DRYNESS "I_MP _

Loud0

Stff_0

SlGNL_.

Hald f:_ 3

seconds

]o_ / un/odc Pause

_n_l

WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

The following isa guide to starting your dryer. Please refer to specific sections of this manual for more detailed information.

1. Clean lint screen before or after each cycle. See "Cleaning

the Lint Screen."

Place laundry into dryer and shut doon See "Loading."

Rotate the dial to select either an Automatic or Manual Cycle

then press the CONTROL ON button. The preset settings and drying time for the cycle chosen will be displayed.

To use an Automatic Cycle

m Point the dial to an Automatic Cycle.

Select DRYNESS LEVEL to adjust how dry you want the load to be. The time displayed is an estimated length of

the cycle based on the Dryness Level selected. Asthe

cycle runs,the control senses the dryness ofthe load and adjusts the time automatically for the selected Dryness

Level.

Fire Hazard

No washer can completely remove o11. Do not dry anything that has ever had any type of oll on

It (Including cooking oils). Items cordalnlng foam, rubber, or plaatlc must be dried

on a clothesline or by using an Air Cycle. Failure to follow these Inatructlons can result In death

or fire.

I om

Less

DRYNESS

LEVEL

NOTE: Time is not adjustable for Automatic Cycles. Pressing

the Manual DryTime (- or +) buttons will cause a triple beap, indicating that the time cannot be changed.

m Press the EXTRA CARE feature button ifthis option is

desired.

Press the CYCLE END SIGNAL button to set signal

volume to desired level.

Press (and hold) HOLD TO START button until dryer starts (about 1 second).

Once an Automatic cycle has started, the Extra Care feature and the Cycle End Signal level can be adjusted. Pressthe OFF button twice to stop the dryer and clear the settings, allowing you to select another cycle and Dryness Level.

To usa a Manual Cycle a Rotate the dial to select a Manual Cycle.

Press MANUAL DRY TIME (- or +) buttons untilthe desired drying time is displayed. Tap - or + and the time will change by 1-minute intervals. Press and hold - or + and the time will change by5-minute intervals. The initialtime displayed isthe actual drying time.

DRY 11ME

NOTE: The Manual Dry Time feature can be used only with

Manual Cycles. m Press TEMP until the desired temperature glows.

NOTE: Pressing the Dryness Level button will cause the triple beep indicating that this option is not selectable. Also, a

Dryness Level is not indicated. m Press the EXTRA CARE feature button ifthis option is

desired.

a Press the CYCLE END SIGNAL button to set volume to

desired level.

a Press(and hold) HOLDTO STARTbutton untildryer starts

(about1 second).

While a Manual Cycle isrunning, you can change the settings for "Sme, Temperature, the Extra Care feature, and the Cycle

End Signal. Pressthe OFF button twice to stop the dryer and clear the settings, allowing you to select another cycle.

Stopping Your Dryer

To stop your dryer at any time

Press OFF twice or open the door.

Pausing or Restarting

To pause the dryer at any time Open the door or press OFF once.

To restart the dryer Close the door and press (and hold) HOLD TO START button until

dryer starts.

NOTE: Dryingwill continue from where the cycle was interrupted

if you close the door and press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will shut off. Select new cycle settings before restarting the dryer.

Control Locked

This feature allows you to mockyour settings to prevent unintended use ofthe dryer. You can also use the Control Locked feature to prevent unintended cycle or option changes during dryer operation.

To enable the Control Looked feature when dryer is running:

Press and hold the CYCLE END SIGNAL button for 3 seconds.

The control islocked when a single beep is heard and the Control

Locked status light is on.

= When the dryer isoff, it is not necessary to press the Control

On button before activating the Control Locked feature.

To unlock:

Press and hold the CYCLE END SIGNAL button for 3 seconds to

turn this feature off.

NOTE: When the dryer is running and Control Locked is on, the

dryer can be stopped by pressing the Off button, but can't be restarted until the control is unlocked.

Propedy loading your dryer can lower your utility bill and prolong

the life of your garments.

Loading suggestions

a Load the dryer by the amount of space items take up, not by

their weight.

a Do not overload the dryen This causes wrinkling and uneven

drying.

Super Capacity Plus Dryers

Heavy Work Clothes

4 jeans 4 workpants

4 workshirts

Towels

I 0 bath towels I 0 hand towels

Mixed Load

3 sheets (1 king, 2 twin) 4 pillowcases

3 shirts 3 blouses

Drying and Cycle Tips

Select the correct cycle and dryness level or temperature for your load. If an Automatic Cycle is running,the display shows the estimated cycle time when your dryer is automatically sensing the dryness level of your load. If a Manual Cycle is running, the display shows the exact number of minutes remaining in the cycle.

Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level.

Drying tips

= Follow care label directions when they are available. a If desired, add afabric softener sheet. Follow package

instructions.

a Remove the load from the dryer as soon as tumbling stops to

reduce wrinkling. This is especially important for permanent

press, knits, and synthetic fabrics.

a Avoid drying heavy work clothes with lighter fabrics. This

could cause overdrying of lighter fabrics, leading to increased shrinkage or wrinkling.

Cycle tips

a Drymost loadsusingthe presetcyclesettings.

a Refer to the Automatic or Manual Preset Cycle Settings chart

(in the "Cycles" section) for a guide to drying various loads.

Drying temperature and Dryness Level are preset when

you choose an Automatic Cycle. You can choose a

different dryness level, depending on your load by pressing the DRYNESS LEVEL button to select MORE or

LESS.

Ifyou wish to adjust the cycle length of a Manual Cycle,

you must press the MANUAL DRY TIME (- or +) buttons. Adjust the temperature of a Manual Cycle by pressing TEMP untilthe desired temperature is selected.

NOTE: You cannot choose a Dryness Levelwith Manual

Cycles.

2 sweatpants 2 sweatshirts

14 washcloths

g T-shirts g shorts

10 handkerchiefs

Lish

You may follow the progress of your dryer with the drying status indicator lights.

SensingO

WetO

Damp O

CoolDown O

CycleComplete O

ExtraCare O

ControlLockedO

Sensing

When a cycle is first turned on, the SENSING light glows until a wet item is detected.

= In an Automatic cycle, if a wet item has not been detected

within 1O minutes, the Sensing light will turn off and the dryer will shut down.

= In a Manual cycle, if awet item is not detected after

1Ominutes the Wet lightturns on and the selected cycle continues.

Cydes

Select the drying cycle that matches the type of load you are

drying (see Automatic Preset or Manual Preset Cycle Settings

charts).

AUTOMAtiC MANUAL

Heavy Duty Timed DW

Normal ,Touchup

Casual,

Cycle control knob

Automatic Cydes

Automatic Cycles allow you to match the cycle to the load you are drying. See the following Automatic Preset Cycle Settings

chart. Each cycle dries certain fabrics at the recommended temperature. A sensor detects the moisture in the load and automatically adjusts the drying time for optimal drying.

Wet The WET light will turn on when a wet item has bean detected in

the dryer. The Wet light will remain on until:

= The damp dry point is reached in an Automatic cycle. = The dryer enters the cool down period in a Manual cycle.

Damp

The DAMP light indicates that the load has reached the damp dry level.

NOTE: The Damp lightis not used with manual cycles.

Cool Down The COOL DOWN light glows during the cool down part ofthe

cycle. Laundry is cooling down for ease in handling.

Cycle Complete The CYCLE COMPLETE light glows when a drying cycle is

finished. If the Extra Care feature has been selected, the Extra Care feature indicator light will also be on.

The Cycle Complete light turns off one hour after the end of a drying cycle (includingthe Extra Care cycle of 2 hours), when Off is pressed, or when the door is opened.

Extra Care Feature

The EXTRA CARE feature light glows when this option is selected. This indicator stays on with the Cycle Complete light.

Heavy Duty Usethis cycleto get Highheatforheavyfabrics suchascotton

towelsor bedspreads,

Normal Use this cycle to get Medium heat for drying sturdy fabrics such

as work clothes.

Casual

Use this cycle to get Medium heat for drying no-iron fabrics, such

as sport shirts, casual business clothes and permanent press blends.

Delicate Use this cycle to get Low heat for drying synthetic fabrics,

washable knit fabrics and no-iron finishes,

Super Delicate

Use this cycle to get Extra Low heat to gently dry items such as

lingerie, exercise wear, or sheer curtains.

Control Locked The CONTROLLOCKEDlightglowswhenthisoptionisenabled.

Indicator lights

Other indicator lights on the control panel show Cycle, Temper-ature, and Cycle End Signal settings selected,

The time display will indicate the estimated or actual time remaining in a cycle,

Automatic Preset Cycle Settings

Automatic Cycles Temp. Time*

Load Type (Minutes)

HEAVY DUTY High 40 Heavyweight, towels

NORMAL Medium 34

Corduroys, work clothes

CASUAL Medium 36

Permanent press, synthetics

DELICATE Low 28 Lingerie, blouses, washable

woolens

SUPER DELICATE Extra Low 22

Exerciea wear, sheer curtains, lace

*Estimated Time with Dryness Level (medium) setting.

Manual Cydes

Use Manual Cycles to select a specific amount of drying time and

a drying temperature. When a Manual Cycle is selected, the

ESTIMATED TIME REMAINING display shows the actual time

remaining in your cycle. You can change the actual time inthe cycle by pressing the Manual Dry Time (- or +) buttons.

Timed Dry

Use this cycle to complete drying if items are still damp after an

Automatic Cycle. Timed Dry is also useful for drying heavyweight and bulky items, such as bedspreads and work clothes.

Touchup

Use this setting to remove wrinkles from items, such as clothes

packed in a suitcase or items wrinkled from being left inthe dryer too long.

Rapid Dry Use this cycle for drying small loads or loads that need a short

drying time.

Manual Preset Cycle Settings

Manual Cycles Tamp. Default Time Load Type (Minutes)

TIMED DRY High 40

Heavyweight, bulk, bedspreads, work clothes

TOUCHUP Medium 20

Remove wrinkles

RAPID DRY High 27 Small loads

Additional Features

Extra Care Feature

When you are unable to remove a load of clothes from the dryer as soon as it stops, wrinkles can form. The Extra Care feature periodically tumbles, rearranges and fluffsthe load to help reduce

wrinkles.

• Press the Extra Care feature to get up to 120 minutes of heat- free, periodic tumbling at the end of a cycle.

• Stop at any time by pressing the Extra Care feature or

opening the dryer door.

Forthe Casual Cycle, the Extra Care feature is preset to "On."

The other Automatic Cycles will retain the Extra Care feature setting. (For example, if you select the Extra Care feature in the Normal cycle, the Extra Care feature will be on the next time you select the Normal cycle.)

NOTE: If you do not select the Extra Care feature, the dryer stops

after the cool down period.

Temperature Temperature settings are used with the Manual Cycles. Press

TEMP until the desired temperature setting glows. Temperature settings cannot be used with the Automatic Cycles.

Ii High

Medium Low Extra Low

Air On[y

TEMP

Air Only

Use the Air Only setting for items that require drying without heat

such as rubber, plastic and heat-eanaltive fabrics. This chart shows examples of items that can be dried using Air Only.

Type of Load "rime*

(Minutes)

Foam rubber - pillows, padded bras,

stuffed toys

Plastic - Shower curtains, tablecloths 20 - 30

Rubber-backed rugs 40 - 50

Olefin, polypropylene, sheer nylon 1O- 20

*Reset time to complete drying, if needed.

When using Air Only

• Check to see that coverings are securely stitched.

• Shake and fluff pillows by hand periodically during the cycle.

• Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Automatic Cycles are not available when using the Air

Only setting.

20 - 30

Cycle End Signal The Cycle End Signal produces an audible sound when the

drying cycle is finished. Promptly removing clothes at the end of the cycle reduces wrinkling.

solo I

CYCLE

END

SIGNAL

Holdfor3

_ds to

lock/unrock

control

Press and release the CYCLE END SIGNAL to adjust the sound

level or turn off the signal.

NOTE: When the Extra Care feature is selected and the Cycle End Signal is on, an audible sound will emit every 5 minutes until

the clothes are removed, or the Extra Care feature is finished.

Drying Rack

The drying rack is useful for drying items you would not necessarily want to tumble dry or that you would normally line dry (for example, sweaters).

To use the drying rack

Do not remove the lint screen.

1. Open dryer door.

3. Put the wet items on top ofthe rack. Leave space between the items so air can reach all the surfaces.

NOTE: Do not allow items to hang over the edge of the rack.

Close the door.

Select a timed drying cycle and temperature, or an air cycle (see following chart). Items containing foam, rubber, or plastic must be dried on a clothesline or by using the Air Only temperature setting.

6. You must select a time by pressing the MANUAL DRY TIME (- or +) buttons. Reset time as needed to complete drying.

Refer to the following table.

7. Press (and hold) HOLD TO START button (about 1 second).

NOTE: You must remove rack for normal tumbling. Do not use

automatic cycles with the drying rack. This chart shows examples of items that can be rack dried and

the suggested cycle, temperature setting and drying time. Actual drying time will depend on the amount of moisture items hold.

Rack Dry Setting Temp. "rime*

Wool Sweaters Timed Low 60

Block to shape and lay flat on Dry

the rack

A. Front edge

Place drying rack inside dryer drum, positioning the back wire

on the ledge of the inner dryer back panel. Push down on front edge of drying rack to secure over the lint screen.

A. Dryer back panel

Stuffed toys or pillows Timed Low 60 Cotton or polyester fiber filled Dry

Stuffed toys or pillows Timed Air Only 90

Foam rubber filled Dry (no

heat)

Sneakers or canvas shoes Timed Air Only 90

Dry (no

heat)

*(Minutes) Reset time to complete drying, if needed.

+ 50 hidden pages