KitchenAid YKEBS278DW6, YKEBS278DB6, YKEBS278DM6, YKEBS177DW6, YKEBS177DT6 Installation Guide

...

Quick Reference

Table of Contents:

Pages

[] Product dimensions [] Cutout dimensions

[] Before you start [] Electrical requirements

[] [] Installation steps

If you need assistance:

Check your Use and Care Guide for a toll-free number to call or call the dealer from whom you purchased this appliance. The dealer is listed in the Yellow Pages of your

phone directory under "Appliances -- Household -- Major

-- Service and Repair." Call when you:

[] Have questions about built-in oven installation or

operation.

[] Need to obtain the name and number of an authorized

service company.

When you call, you will need: [] The built-in oven model number.

[] The built-in oven serial number.

Both numbers are listed on the model/serial rating plate, located on the oven door or on the oven frame.

27-1/2"

(69.9cm)

recessed

height

23"

(58.4 _4_

cm)

max.

recessed

depth

Single oven

25-3/8"

(64.5 cm) max.

(68 cm)

overall width

27" (68.6 cm) ram. _1

cabinet width

29"

(73.7 cm}

max.

overall height

1-1,

(3.8 cm) min. A

top of cutout

to underside

of countertop

Double oven

25-3/8"

(64.5 cm) max.

49-1/2"

1125.7cm) recessed

height

23" 26-3/4" (58.4 cm) \ overall width

max.

recessed depth

4-- min. cabinet

27" (68.6 cm) ___,,

cm)

49-3/4"

1126.4 cm) min,

cutout

height

25-1/2"

(64.8 cm)

___ cutout

width

51"

1129.5cm)

max,

overall

1" (2.5 cm) top

of cutout to bottom of upper

cabinet door

Important: Observe all governing codes and ordinances.

Proper installation is your responsibility. Have a qualified technician installthis oven.

Oven location should be away from strong draft areas, such as windows, doors and

strong heating vents. Cabinet opening dimensions that are shown

must be used. Given dimensions provide minimum clearance.

Recessed installation area must provide complete enclosure around the recessed portion of the oven.

Electrical ground is required. See "Electrical requirements."

Electrical supply junction box should be located 3 inches(7.6 cm) maximum belowthe

support surface when oven is installed in a wall cabinet. Drill a 1-inch minimum (2.5 cm)

diameter hole inthe right rear or left rear corner of the support surface to pass the appliance cable through to the junction box.

For undercounter installation, it is recommended that the junction box be

located inthe adjacent right or left cabinet. If installingthe junction box on rear wall behind oven, junction box must be recessed and located inthe upper or lower right or left

corner of cabinet.

It is the customer's responsibility: To contact aqualified electrical installer.

To assure that the electrical installation is

adequate and in conformancewith National Electrical Code, ANSI/NFPA 70 m latest edition*, or Canadian Electrical Code, 022.1- 1982 and 022.2 No.01982 (or latest edition)**

and all local codes and ordinances.

Copies of the standards listed may be obtained from:

* National Fire Protection Association

Batterymarch Park Quincy, Massachusetts 02269

** Canadian Standard Association

178 Rexdale Boulevard Etobicoke, Ontario, Canada Mgw 1R3

Tool needed:

27-3/4"

(70.5 cm)

min.

cutout

height

25-1/2"

(64.8 cm}

cuteut width

Single oven

undercounter

(without cooktop

installed above)

27"(68.6 cm)

min.

cabinet width

_(64.8 cm)_

25-1/2"

cutout

width

5-1/4" 113.3cm}

bottom of cutout

to floor _-

1-1/2" 13.8cm)

rain. bottom of

cutout to top of

cabinet door

1" (2.5 cm) top

of cutout to

bottom of upper cabinet door

Double oven

23-1/4"

159.1cm) min. cutout depth

23" (58.4 cm)

"_-_recessed oven_

depth

14-3/4"

(37.5 cm)

bottom of

cutout to floor

screwdriver

Partssupplied:

4 screws (double oven)

C' apns

Note: If installing a single oven, you will need

only two screws and two door removal pins.

1-1/2"

(3.8 cm)

bottom of

cutoutto

top of

cabinet

Page 1

min.

door

Single oven

32"

181.3cm)

bottom of

cutout to

floor

cabinet---_

recessed

oven

Cabinet side view

_even

front

Electrical Shock Hazard

Electrically ground oven. Connect ground with lO-gauge-minimum solid

copper wire.

Failureto follow these instructions could result in death, fire or electrical shock.

if codes permit and a separate grounding wire is used, it is recommended that a qualified

electrician determine that the grounding path and wire gauge isin accordance with local

codes. Do Not ground to a gas pipe.

Check with a qualified electrician if you are not sure oven is properly grounded.

Do Not have a fuse in the neutral or

grounding circuit.

Oven must be connected to the proper electrical voltage and frequency as specified

on the model/serial rating plate. (The model/serial rating plate is located on the oven door or on the oven frame.)

D CONNECT WITH COPPER WIRE ONLY. [] Models rated from 7.3 to 9.6 kW at 240

volts (5.5 to 7.2 kW at 208 volts) require a

separate 40-ampere circuit. Models rated at 7.2 kW and below at 240 volts (5.4 kW

and below at 208 volts) require a separate 30-ampere circuit.

[] Atime-delay fuse or circuit breaker is

recommended.

[] Connect directly to the fused disconnect

(or circuit breaker box) through flexible, armored or non-metallic sheathed, copper

cable (with grounding wire).

[] Flexible armored cable from appliance

should be connected directly to junction box.

[] Fuse both sides ofthe line.

[] A U.L.-listed conduit connector must be

provided at the junction box.

[] Do Not cut the conduit. Wire sizes and connections must conform

with the rating of the appliance and to the requirements of the National Electrical

Code, ANSI/NFPA 70 -- latest edition*, or Canadian Electrical Code, C22.1-1982 and C22.2 No. 01982 (or latest edition)** and all local codes and ordinances.

Copies of the standards listed may be obtained from:

* National Fire Protection Association

Batterymarch Park Quincy, Massachusetts 02269

** Canadian Standard Association

178 Rexdale Boulevard

Etobicoke, Ontario, Canada MgW 1R3

_ Grasp oven

frame to lift

oven.

i II

_ power

supply cable

_ Remove

shipping

feet.

Preparation

Use screws to attach

oven to cabinet.

Reattach side trim.

Remove trim screws.

Remove side

trim.

_ power

oven.

Use screws to

_'__ attach oven to

cabinet.

supply cable

_ Remove

shipping

feet.

Remove

oven racks.

Checkoven 1

operation.

eattach side

trim.

Remove side trim.

Remove trim screws.

Remove

oven doors.

ExcessiveWeight Hazard

Use two or more peopleto move and install

oven,

Failure to follow this instruction canresult in back or other injury.

important:Use both hands to remove oven

doors. Do Not use handle or any portionof the front

frame or trim for lifting. Before moving oven across floor, checkthat oven

ison shipping base or slide oven onto cardboard or hardboard.

Do Not remove shipping feet at the front lower

cornersof oven.

Replace oven doors

insert small end of pin

here.

Remove trim screw.

Pull trim out.

Pull top of trim down.

DoNot remove

shipping feet.

[] Turn power supply off. Move oven

close to final position.

• Remove and discard shipping materials, tape and protective film from the oven.

Do Not remove shipping base or shipping feet at the front lower corners of oven. The shipping feet will protect

the lower oven trim until oven is

inserted into cabinet.

• Remove and set aside racks and other

parts from inside oven.

Page 2

[] Completely open lower oven door.

Insert small end of a door removal pin into each door hinge. Grasp door handle from the

bottom and gently close door as far as it will shut. Lift slightly and grasp bottom of door

with other hand. Pull door out at bottom to remove. Set door aside on protected surface. Repeat for upper oven door.

,, Remove trim screws attaching right

and left side trim to oven, Grasp the bottom end of trim and pull away from oven. Slide

top end of trim downward to remove trim

from oven. Take care not to scratch other surfaces with ends of trim. Set trim and

screws aside on protected surface.

Electricalconnection

cable from power supply

junction

box

junction

box _

cable from power supply

red __ white

Electrical Shock Hazard

Disconnect powerto the junction box before makingconnection.

Electricallyground oven. Connect ground with 10-gauge-minimum solid

copper wire.

Failureto follow these instructions could result in death, fire or electrical shock.

Thisoven is manufactured with white {neutral) power supply wire and a cabinet-connected bare

groundingwire twisted together.

Feed oven cable through opening in

[] the cabinet. Make electrical connection

following the steps needed for your installation.

1. Disconnect the power supply.

2. Remove the junction box cover.

3. Connect oven cable to junction box through the U.L-listed conduit connector.

4. Connect the two black wires together with

twist-on connectors.

5. Connect the two red wires together with

twist-on connectors.

6. Complete electrical connection according to local codes and ordinances.

wire

white

grounding oven U.L.-listed cable wires i "_ conduit

factory crimped cable from connector

Figure 1 oven

if local codes PERMIT

connecting cabinet-

grounding conductor to

neutral white wire in

junction box:

7. Connect the factory-crimped

bare and white oven cable wires

to the neutral (white) wire in junction box. See Figure 1.

8. Replace junction box cover.

W_ reS

bare grounding _ J ....

wires _ _ U.L.-listed conduit

Figure 2 cable from

Y -"m___ _ black wires

if local codes DO NOT

PERMIT connecting

cabinet-grounding

conductor to neutral

white wire in

junction box:

7. Separate the factory-

crimped bare and white oven cable wires.

8. Connect white oven cable wire to neutral

(white) wire in junction box. See Figure 2.

9. Connect the bare grounding oven cable

wire to a grounded wire in the junction box. See

Figure 2.

10. Replace junction box cover.

oven

connector

if connecting to a

four-wire electrical

system:

7.Separate bare and white oven cable wires.

8.Connect white oven cable wire to neutral (white) wire

injunction box. See Figure 2.

9.Connect the bare grounding oven cable wire

to the green grounding wire injunction box. Do

Not connect bare

groundingwire to neutral (white) wire in junction

box. See Figure 2.

10. Replace junction box cover.

Attachment

Carefully pushagainst seal area of oven front frame when pushingoven into

cabinet. Do Not push against outside edges.

_ Lift oven into

cabinet cutout usin( oven opening as an area

to grip.

shipping foot

Push against seal area of front frame to

push oven into cabinet until shipping feet almost contact cabinet. Use a Phillips screwdriver to remove screws attaching shipping feet. Remove and discard shipping

feet.

Push oven completely into cabinet and center oven in cabinet cutout.

!4 screws

[] Important: Securely fasten oven to cabinet using the screws provided (two screws for a single oven or four screws for a double oven). Insert the screws through holes in mounting rails. Do Not overtighten screws.

Slide top of trim up. _ ! Pushtrim

22_ _ into place.Replace

trim screw.

[] Replace oven racks.

oven frame hinge slot

_door

hinge

Replace the single or upper oven door by

[] insertingends of hinges into hinge slots in

oven frame. Push behind each hinge so that hinges are pushed into oven frame as far asthey will go.

Open door and remove both door removal pins. Close and open door to checkthat door closes and opens completely, if door does not close or open

completely, you have not pushed hinges completely intoframe. Repeat door removal step

and reinsert door into hinge slots again. Repeat for lower oven door.

Check operation

O[] Turn on power supply. The

display panel will light up briefly. "PF" should appear in the temperature display.

/ 'if i ....i

BAKEil BROIL CLEAN!

< J k J k _'!

[]

Check the operation of your single oven.

Press the "BROIL" pad. "BROIL" will appear in the display. Press the "START" pad.

Page3

[] Slide top end of each trim upward onto

oven side rails. Push each trim into place at bottom of trim. Use screws to attach eachtrim

to oven. Take care not to scratch other

surfaces with ends of trim.

Make sure the oven door is closed and the

"ON" light is shown in the display area. After

2 minutes, partially open oven door. You should feel heat from the oven. Press the

"CANCEL" pad.

Checkthe operation of your double oven. Press the "Upper Oven" pad. Pressthe

"BROIL" pad. "BROIL" will appear inthe

display. Pressthe "START" pad. Make sure

the oven door is closed and the "ON" light is

shown in the display area. After 2 minutes, partially open oven door. You should feel heat from the oven. Press the "CANCEL" pad.

Press the "Lower Oven" pad and repeat the steps you completed for checking the upper

oven.

If your oven does not heat or an "F", followed by a number, appears in the display, contact your

dealer or checkthe "if you need service..." section of this Installation

Instructions.

To get the most efficient use

from your new oven, read your

Use and Care Guide. Keep

Installation Instructions

and Guide close to oven

for easy reference.

+ 7 hidden pages