Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
follow instructions.
can be killed or seriously injured if you don't
You
instructions.
follow
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
■
Plug into a grounded 3 prong outlet.
■
Do not remove ground prong.
■
Do not use an adapter.
■
Do not use an extension cord.
■
Disconnect power before servicing.
■
Replace all parts and panels before operating.
To reduce the risk of fire, electric shock, or injury when using your wine cellar, follow these basic precautions:
■
Remove doors from your old wine cellar.
■
Use nonflammable cleaner.
■
Keep flammable materials and vapors, such as gasoline,
away from wine cellar.
■
Use two or more people to move and install wine cellar.
SAVE THESE INSTRUCTIONS
Proper Disposal of Your Old Wine Cellar
WARNING
Suffocation Hazard
Remove door from your old wine cellar.
Failure to do so can result in death or brain damage.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned wine cellars are still dangerous
– even if they will sit for “just a few days.” If you are getting rid of
your old wine cellar, please follow these instructions to help
prevent accidents.
Before You Throw Away Your Old Wine Cellar:
■ Take off the door.
■ Leave the racks in place so that children may not easily climb
inside.
3
INSTALLATION INSTRUCTIONS
Location Requirements
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from wine cellar.
Failure to do so can result in death, explosion, or fire.
To ensure proper ventilation for your wine cellar, allow for a 5"
(127 mm) space between the back of the beverage center and
the wall. When installing your beverage center next to a fixed
wall, leave 13¹⁄₄" (33.7 cm) minimum clearance on the hinge side
to allow for the door to swing open.
NOTE:
■ It is recommended that you do not install the wine cellar
near an oven, radiator, or other heat source. Do not install
in a location where the temperature will fall below 55°F
(13°C). For best performance, do not install the wine
cellar behind a cabinet door.
■ It is recommended that you install the wine cellar in a
location that allows the door to have a greater than 45°
opening. A limited door swing will keep the shelves from
sliding out as intended and may lead to damaging the
door gasket.
■ The rough cabinet opening must be on a level floor and at
least 24" (60 cm) deep and 12¹⁄₂" (31.75 cm) wide.
Electrical Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your wine cellar into its final location, it is
important to make sure you have the proper electrical
connection.
Recommended grounding method
A 115 Volt, 60 Hz., AC only, 15– or 20–amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your wine cellar be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
NOTE: Before performing any type of installation or cleaning
unplug wine cellar or disconnect power.
Unpack the Wine Cellar
WARNING
Excessive Weight Hazard
5" (12.17 cm)
13¹⁄₄" (33.66 cm)
4
Use two or more people to move and install wine cellar.
Failure to do so can result in back or other injury.
Remove the Packaging
■ Remove tape and glue residue from surfaces before turning
on the wine cellar. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water
and dry.
■ Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your wine cellar. For
more information, see “Wine Cellar Safety.”
■ Dispose of/recycle all packaging materials.
When Moving Your Wine Cellar:
Your wine cellar is heavy. When moving the wine cellar for
cleaning or service, be sure to cover the floor with
cardboard or hardboard to avoid floor damage. Always pull
the wine cellar straight out when moving it. Do not wiggle
or “walk” the wine cellar when trying to move it, as floor
damage could occur.
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your wine cellar before using it. See the cleaning instructions in
“Wine Cellar Care.”
Wine Cellar Doors
TOOLS NEEDED: #2 Phillips screwdriver; adjustable wrench
IMPORTANT: All graphics referenced in the following instructions
are included later in this section after “Final Steps.” The graphics
shown are for a right-hand swing door (hinges factory installed on
the right).
Reverse Door Swing (optional)
1. Remove the plastic door pin cap from the top left side of the
door and reinstall it on the right side of the door.
2. Remove the 3 plastic screw caps from the top left side of the
cabinet and transfer them to the top right side of the cabinet.
See Graphic 1.
3. Install the top hinge on the left side of the cabinet and secure
with the 3 screws.
4. Install the hinge cover over the top hinge using the 2 screws.
5. Install the 2 plastic screw caps on the hinge cover.
6. Insert the top corner of the door into the top hinge pin and
reinstall the door on the wine cellar.
7. Using the left side bottom hinge supplied with your wine
cellar, insert the hinge pin into the bottom of the door. See
Graphic 6.
8. Align the hinge holes with the holes in the cabinet and secure
with 3 screws.
9. Install the leveling leg that was in the right bottom hinge into
the left bottom hinge. See Graphic 4.
10. Install the leveling leg that was on the left side of the wine
cellar onto the right side. See Graphic 5.
Remove Door and Hinges
1. Unplug wine cellar or disconnect power.
WARNING
Excessive Weight Hazard
Use two or more people to move and install wine cellar.
Failure to do so can result in back or other injury.
2. Place the wine cellar on its back.
3. Unscrew the two leveling legs, one from the bottom hinge on
the right hand side and one from the left hand side of the
cabinet. See graphics 4 and 5.
4. Remove the 3 screws from the bottom hinge and remove the
bottom hinge. See Graphic 3.
NOTE: Keep the hinge in the event the wine cellar door needs
to be returned to its original door swing.
5. Remove the door by pulling it downward and off the top pin
and set aside.
6. Remove the 2 plastic screw caps located on the top of the
hinge cover. See Graphic 2.
7. Remove the screws holding the hinge cover to the top hinge
and remove the top hinge cover. See Graphic 2.
8. Remove the 3 screws from the top hinge and remove the top
hinge. See Graphic 2.
Final Steps
1. Check the alignment of the door and the door seals.
2. Check that the door lock slides easily into the lock chamber.
3. Tighten all hinge screws.
4. Return the wine cellar to its upright position and wait
60 minutes before reconnecting the power.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
5. Plug into a grounded 3 prong outlet.
5
A
A. Plastic Screw Caps
1
Top Hinge
A. Hinge Cover Screw Caps
B. Hinge Cover Screws
C. Hinge Cover
D. Top Hinge Screws
E. Top Hinge
F. Hinge Pin
2
A
B
C
D
E
F
6
Left Bottom Hinge
(provided)
A
B
C
D
5
A. Washers
B. Hinge Pin
C. Bottom Hinge
D. Bottom Hinge Screws
Leveling Leg
Door Closing
Your wine cellar has two leveling legs. If your wine cellar seems
unsteady or you want the door to close more easily, adjust the
wine cellar’s tilt using the instructions below.
4
Leveling Leg
for Bottom Hinge
Right Bottom Hinge
A. Washers
B. Hinge Pin
C. Bottom Hinge
D. Bottom Hinge Screws
WARNING
3
A
B
C
D
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
6
WARNING
Excessive Weight Hazard
Use two or more people to move and install wine cellar.
Failure to do so can result in back or other injury.
2. Move the wine cellar into its final location.
3. Turn the leveling legs to the right to lower the wine cellar or
turn the leveling legs to the left to raise it. It may take several
turns of the leveling legs to adjust the tilt of the wine cellar.
NOTE: Having someone push against the top of the wine
cellar takes some weight off the leveling legs. This makes it
easier to adjust the leveling legs.
4. Make sure that the door closes as easily as you like. If not, tilt
the wine cellar slightly more to the rear by turning both front
leveling screws to the right. It may take several more turns,
and you should turn both leveling legs the same amount.
Using the Control
Your wine cellar has electronic temperature controls that allow
you to set the temperature in both the upper and lower
compartments. This allows you to select the exact temperature to
meet your specific wine storage needs.
Upper chamberLower chamber
RUN
Activation
CHAMBER SUPRIEURECHAMBER INFRIEURE
Adjusting Controls
The temperature of the wine cellar can be set in a range between
39°F (4°C) and 64°F (18°C). Each compartment can be set to a
different temperature in that range.
To set the upper compartment temperature, press the Set Upper
button. The temperature will change by 1 degree each time the
button is pressed.
To set the lower compartment temperature, press the Set Lower
button. The temperature will change by 1 degree each time the
button is pressed.
Temperature Display
Set Upper
RGLER SUPRIEURE
Set Lower
RGLER INFRIEURE
WINE CELLAR USE
Normal Sounds
Your new wine cellar may make sounds that your old one didn’t
make. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard
surfaces, such as the flooring and surrounding structures, can
make the sounds seem louder. The following describes the kinds
of sounds and what may be making them.
■ Your wine cellar is designed to run more efficiently to keep
your food items at the desired temperatures and to minimize
energy usage. The high efficiency compressor and fans may
cause your wine cellar to run longer than your old one. You
may also hear a pulsating or high-pitched sound from the
compressor or fans adjusting to optimize performance.
■ Rattling noises may come from the flow of refrigerant or items
stored inside the wine cellar.
■ As each cycle ends, you may hear a gurgling sound due to
the refrigerant flowing in your wine cellar.
■ You may hear water running into the drain pan when the wine
cellar is defrosting.
■ You may hear clicking sounds when the wine cellar starts or
stops running.
The temperature separator displays the current temperatures
(Fahrenheit or Celsius) for the upper and lower compartments of
the wine cellar. To switch from Fahrenheit to Celsius, press and
hold the Set Upper and Set Lower buttons simultaneously for
approximately 5 seconds until a beep sounds and the display
changes.
To view the current temperature setting for a compartment, press
the button for that compartment once, and the temperature will
flash for 5 seconds and then will return to the current
temperature.
Lock
The wine cellar is equipped with a lock that is located behind the
door handle. To lock the wine cellar, insert the key all the way into
the lock and turn clockwise. To unlock, turn the key
counterclockwise.
Wine Racks
To Remove and Replace the Wine Racks
1. To remove a rack, tilt the rear of the rack up and pull forward.
2. To replace the rack, place the rack on the support brackets
and push the rack down until it locks into place.
7
Stocking the Wine Cellar
The wine cellar has a maximum capacity of 38 bottles of wine,
when the humidors are not in use.
NOTE: For optimum wine storage, place white wines at the
bottom of the wine cellar, light red wines in the center and red
wines at the top.
To Stock the First Four Racks
1. Starting at the left-hand side, place the bottom of the first
bottle against the back of the wine rack in the rear left corner.
2. Place the second bottle beside the first with the bottom of the
bottle aligned with the front trim of the wine rack.
3. Continue in this manner for the next 3 bottles.
4. Place the base of the sixth bottle in the right rear corner of the
rack.
1356
247
Lighting the Wine Cellar
The wine cellar has an interior light that comes on any time the
door is opened.
The light is controlled by a two-position switch.
|Turns the light on.
0Sets the light to turn on only when the door is
opened.
WINE CELLAR CARE
Cleaning
WARNING
5. Place the last bottle between the fifth and sixth placed bottles
with the base of the bottle aligned with the front trim of the
wine rack.
12345
To Stock the Bottom Two Racks
Starting on the left hand side of the wine rack, place 5 bottles on
the rack with the base of each bottle against the back of the wine
rack and the front aligned with the front trim.
Humidors
If humidity conditions are low, it will be necessary to use the
humidors.
1. Fill the humidors about ³⁄₄ full with fresh water.
2. Place 1 humidor on the bottom most rack of both the lower
and upper compartment. Place the longest side of the
humidor so that it runs parallel with the right wall of the wine
cellar.
3. Check the water level occasionally and refill as necessary.
NOTE: Each humidor reduces the storage capacity of the wine
cellar by 1 bottle when installed according to instructions.
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
Clean the wine cellar about once a month to avoid buildup of
odors. Wipe up spills immediately.
To clean your wine cellar:
1. Unplug wine cellar or disconnect power.
2. Remove all racks from inside the wine cellar.
3. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
■ To protect wood trim pieces, do not immerse the entire
rack into water when cleaning.
■ Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior
and door liners or gaskets. Do not use paper towels,
scouring pads, or other harsh cleaning tools. These can
scratch or damage materials.
■ To help remove odors, you can wash interior walls with a
mixture of warm water and baking soda (2 tbs to 1 qt
[26 g to 0.95 L] of water).
4. Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners, or cleaners containing
chlorine. These can scratch or damage materials. Dry
thoroughly with a soft cloth. For additional protection against
damage to painted metal exteriors, apply appliance wax (or
auto paste wax) with a clean, soft cloth. Do not wax plastic
parts.
5. Replace the racks.
8
6. Wash the humidors in warm soapy water.
NOTE: To avoid breakage, do not place the humidor into
warm water immediately after removing from the chilled wine
cellar.
7. Plug in wine cellar or reconnect power.
Vacation and Moving Care
Vac ations
If you choose to turn the wine cellar off before you leave, follow
these steps.
1. Remove all wine bottles from the wine cellar.
2. Unplug the wine cellar.
3. Clean the wine cellar. See “Cleaning.”
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
4. Tape a rubber or wood block to the top of the door to prop it
open far enough for air to get in. This stops odor and mold
from building up.
Moving
When you are moving your wine cellar to a new home, follow
these steps to prepare it for the move.
1. Remove all wine bottles from the wine cellar.
2. Unplug the wine cellar.
3. Clean, wipe, and dry it thoroughly.
4. Take out all removable parts, wrap them well, and tape them
together so they don’t shift and rattle during the move.
5. Tape the doors shut and tape the power cord to the wine
cellar.
When you get to your new home, put everything back and refer to
the “Installation Instructions” section for preparation instructions.
Your wine cellar will not operate
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
■ Is the power supply cord unplugged? Plug into a grounded
3 prong outlet.
■ Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse or reset the circuit.
The lights do not work
■ Is the power supply cord unplugged? Plug into a grounded
3 prong outlet.
The motor seems to run too much
■ Is the temperature outside hotter than normal? Expect the
motor to run longer under warm conditions. At normal
temperatures, expect your motor to run about 40% to 80% of
the time. Under warmer conditions, expect it to run even
more of the time.
■ Is the door opened often? Expect the motor to run longer
when this occurs. In order to conserve energy, try to get
everything you need out of the wine cellar at once, keep wine
bottles positioned label side up so that they are easy to find,
and close the door as soon as the wine is removed.
■ Is the control set correctly for the surrounding
conditions? See “Using the Control.”
■ Is the door closed completely? Push the door firmly shut. If
it will not shut all the way, see “The door will not close
completely” later in this section.
Temperature is too warm
■ Is the door opened often? Be aware that the wine cellar will
warm when this occurs. In order to keep the wine cellar cool,
try to get everything you need out of the wine cellar at once,
keep wine bottles positioned label side up so that they are
easy to find, and close the door as soon as the wine is
removed.
■ Is the control set correctly for the surrounding
conditions? See “Using the Control.”
■ Is the exhaust vent blocked? For best performance, do not
install the wine cellar behind a cabinet door or block the
exhaust vent.
■ Has a large number of warm bottles been added? Limit
the number of bottles being placed into the wine cellar at one
time.
There is interior moisture buildup
■ Is the door opened often? To avoid humidity buildup, try to
get everything you need out of the wine cellar at once, keep
wine bottles positioned label side up so that they are easy to
find, and close the door as soon as the wine is removed.
When the door is opened, humidity from the room air enters
the wine cellar. The more often the door is opened, the faster
humidity builds up, especially when the room itself is very
humid.
■ Is it humid? It is normal for moisture to build up inside the
wine cellar when the air is humid.
■ Is the control set correctly for the surrounding
conditions? See “Using the Control.”
9
The door is difficult to open
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
■ Is the gasket dirty or sticky? Clean the gasket and the
surface that it touches. Rub a thin coat of paraffin wax on the
gasket following cleaning.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If You Need Replacement Parts
If you need to order replacement parts, we recommend that you
only use factory specified parts. Factory specified parts will fit
right and work right, because they are made with the same
precision used to build every new WHIRLPOOL
To locate factory specified parts in your area, call us or your
nearest designated service center.
®
appliance.
The door will not close completely
■ Are the racks out of position? Put the racks back into their
correct positions. See “Wine Cellar Use” for more
information.
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
■ Is the gasket sticking? Clean the gasket and the surface
that it touches. Rub a thin coat of paraffin wax on the gasket
following cleaning.
Call customer service toll free toll free: 1-866-568-0386
In Canada call : 1-866-457-1539.
For Further Assistance
If you need further assistance, you can write to us with any
questions or concernt at: