Kitchenaid KXD4630YSS, KXD4636YSS Owner's Manual

30" (76.2 CM) AND 36" (91.4 CM)

RETRACTABLE (POP-UP) DOWNDRAFT

VENT SYSTEM

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call: 1-800-422-1230

In Canada, call: 1-800-807-6777, or visit our website at www.kitchenaid.ca.

or visit our website at www.kitchenaid.com.

SYSTÈME DE VENTILATION RÉTRACTABLE

(CLAPET) DE 30" (76,2 CM) ET 36" (91,4 CM) –

ASPIRATION PAR LE BAS

Instructions d’installation et Guide d’utilisation et d’entretien

Pour des questions à propos des caractéristiques, du fonctionnement/rendement, des pièces, accessoires ou dépannage, composer le :

Au Canada, composer le : 1-800-807-6777 ou visitez notre site web à www.kitchenaid.ca.

1-800-422-1230 ou visitez notre site web à www.kitchenaid.com.

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. FOR RESIDENTIAL USE ONLY. IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.

LI3ZTC/W10342489G

TABLE OF CONTENTS TABLE DES MATIÈRES

VENT SYSTEM SAFETY.................................................................3

INSTALLATION REQUIREMENTS .................................................5

Tools and Parts .............................................................................5

Location Requirements ................................................................5

Electrical Requirements ...............................................................8

Venting Requirements ..................................................................8

INSTALLATION INSTRUCTIONS

INTERIOR-MOUNTED VENT MOTOR ..........................................9

Venting Methods ..........................................................................9

Install Vent System .....................................................................10

Rear Mounting – Blower Motor ..................................................12

Complete Installation .................................................................14

Make Electrical Connections .....................................................16

Check Operation ........................................................................16

INSTALLATION INSTRUCTIONS

EXTERIOR-MOUNTED VENT MOTOR .......................................17

Venting Methods ........................................................................17

Install Vent System .....................................................................18

Complete Installation (Exterior-Mounted Motor) .......................18

Install Downdraft Vent In-Line (External Type)

Blower Motor ..............................................................................20

Make Electrical Connections for In-Line Blower

Motor System .............................................................................21

Make Electrical Power Supply Connection

to Downdraft Vent ......................................................................22

Check Operation ........................................................................23

VENT SYSTEM USE .....................................................................24

Operating Downdraft Vent .........................................................24

VENT SYSTEM CARE ..................................................................24

Surface of Downdraft Vent .........................................................24

Filters ..........................................................................................24

TROUBLESHOOTING ..................................................................25

WIRING DIAGRAMS .....................................................................26

Interior-Mounted Blower Motor ................................................26

Exterior-Mounted Blower Motor ................................................27

ASSISTANCE OR SERVICE .........................................................28

In the U.S.A. ...............................................................................28

In Canada ...................................................................................28

Accessories ................................................................................28

WARRANTY ..................................................................................29

SÉCURITÉ DU SYSTÈME DE VENTILATION .............................30

EXIGENCES D'INSTALLATION ...................................................32

Outils et pièces ...........................................................................32

Exigences d’emplacement .........................................................32

Spéciﬁcations électriques ..........................................................36

Exigences concernant l'évacuation ...........................................36

INSTRUCTIONS D’INSTALLATION

VENTILATEUR MONTÉ À L’INTÉRIEUR.....................................37

Méthodes d’évacuation .............................................................37

Installation du conduit d’évacuation ..........................................38

Montage du ventilateur à l'arrière ..............................................40

Achever l’installation ..................................................................42

Raccordements électriques .......................................................44

Contrôle du fonctionnement ......................................................44

INSTRUCTIONS D’INSTALLATION

VENTILATEUR MONTÉ À L’EXTÉRIEUR ...................................45

Méthodes d’évacuation .............................................................45

Installation du conduit d’évacuation ..........................................46

Achever l’installation (Ventilateur monté à l’extérieur) ...............46

Installation du ventilateur en ligne (type externe)

du système d’extraction par le bas ...........................................48

Raccordements électriques du système

de ventilation en ligne ................................................................49

Raccordement de l’alimentation électrique

au système d’extraction par le bas ............................................50

Contrôle du fonctionnement ......................................................51

UTILISATION DU SYSTÈME D’EXTRACTION ...........................52

Utilisation du système d’extraction par le bas ..........................52

ENTRETIEN DU SYSTÈME D’ÉVACUATION .............................53

Surface du système d’extraction par le bas ..............................53

Filtres ..........................................................................................53

DÉPANNAGE .................................................................................54

SCHÉMA DE CÂBLAGE ...............................................................55

Ventilateur monté à l'intérieur ...................................................55

Ventilateur monté à l'extérieur ...................................................56

ASSISTANCE OU SERVICE .........................................................57

Aux É.-U. ....................................................................................57

Au Canada ..................................................................................57

Accessoires ................................................................................57

GARANTIE .....................................................................................58

VENT SYSTEM SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer. WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

follow instructions.

You

can be killed or seriously injured if you don't

instructions.

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools Needed

■ Jigsaw or keyhole saw

■ Drill

■

/8" (3 mm) drill bit for pilot holes

■ Pencil

■ Tape measure or ruler

■ Flat-blade screwdriver

■ Phillips screwdriver

■

/8" (9.5 mm) nut driver

■ Level

■ Pliers

■ Metal snips

■ Wire stripper or utility knife

■ Caulking gun and weatherproof caulking compound

Parts Supplied

■ Top trim – stainless

■ End caps (2)

■ Lower support legs (2)

■ Undercounter mounting brackets (2)

■ 4 x 8 mm screws (16)

■ 3.5 x 9.5 mm screws (3)

■ 3

/4" x 10" (8.3 cm x 25.4 cm) rectangular damper

■ 4

/4" (12.0 cm) motor box

■ ¼" (6.4 mm) deep cover

■ Flat vent cover plate

■ 6" (15.2 cm) diameter vent transition with damper (interior-

mounted blower motor models only)

■ 10" (25.4 cm) diameter vent collar (exterior-mounted blower

model only)

Parts Needed

■ UL listed or CSA approved ½" (12.7 mm) conduit connector

■ Wall or roof cap with damper to match vent system

■ Vent system

■ Home power supply cable

■ UL listed wire connectors (3)

■ Wiring cable for optional remote blower kit

■ Vent clamps/duct tape as required

Location Requirements

NOTE: Downdraft vent is installed directly behind the cooktop. Install the downdraft vent ﬁrst, and then install the cooktop.

IMPORTANT: Observe all governing codes and ordinances.

■ Have a qualiﬁed technician install the downdraft vent. It

is the installer’s responsibility to comply with installation clearances speciﬁed on the model/serial/rating plate. The model/serial/rating plate is located on the front of the downdraft vent above the terminal box cover.

■ Downdraft vent location should be away from strong draft

areas, such as windows, doors, and strong heating vents or fans.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.

■ Consult the cooktop manufacturer installation instructions

before making any cutouts. Check that the downdraft vent and cooktop location will

clear the cabinet walls, backsplash, and rear wall studs inside the cabinet.

Check for the minimum distance between the front edge of the countertop and the front edge of the cooktop. The minimum horizontal distance between the overhead cabinets is the same as the width of the installed downdraft vent.

■ All openings in ceiling and wall where the downdraft vent

will be installed must be sealed.

■ Grounded electrical outlet is required. See the “Electrical

Requirements” section.

■ When installing the downdraft vent, the cabinet drawer

will need to be removed and the drawer front installed permanently to the cabinet.

Cabinet Construction:

Downdraft vent is designed for use in a cabinet with a depth of 24" (61 cm). Some installations require a countertop deeper than 25" (63.5 cm). See the “Countertop Cutout Dimensions” section.

The maximum depth of the overhead cabinet is 13" (33 cm). Overhead cabinets installed at either side of the downdraft vent must be 18" (45.7 cm) above the cooking surface.

For Mobile Home Installations

The installation of this downdraft vent must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes.

Product Dimensions

Reversed Blower

Range Hood

Models with interior-mounted blower motor

13¹⁄₂" (34.3 cm)

retractable vent height

27" (68.6 cm) for 30" (76.2 cm) vent 33" (83.8 cm) for 36" (91.4 cm) vent

13¹⁄₈" (33.4 cm)

16¹⁄₂" (42.0 cm)

Top trim widths: 30" (76.2 cm) 36" (91.4 cm)

10"

(25.4 cm)

³⁄₄"

(1.9 cm)

2¹⁄₈" (5.4 cm)

1¹⁄₂" (3.8 cm)

³⁄₈" (0.95 cm)

5¹⁄₄" (13.3 cm) for 30" (76.2 cm) vent 8¹⁄₄" (21.0 cm) for 36" (91.4 cm) vent

28¹⁄₂"

(72.4 cm)

Models with exterior-mounted blower motor

4³⁄₄" (12.1 cm)

13¹⁄₈" (33.4 cm)

6⁹⁄₁₆"

(16.7 cm)

10" (25.4 cm)

diameter

vent collar

16¹⁄₂" (42.0 cm)

8¹⁄₄"

(21.0 cm)

³⁄₄" (1.9 cm)

As-Received Blower

Front of

10" (25.4 cm)

Front of

Range Hood

4³⁄₄"

(12 cm)

(25.4 cm)

16¹⁵⁄₁₆" (43 cm)

10"

Cabinet Dimension

¹⁄₂

minim

of the cabinet.

Interior-mounted blower motor model Exterior-mounted blower motor model

A = ¹⁄₂" (12.7 mm) minimum

21⁵⁄₁₆" (54.1 cm)

Cutouts are for 3¹⁄₄" x 10" (8.3 cm x 25.4 cm) rectangular or 6" (15.2 cm) round vent system.

Locate power supply junction box at lower left-hand rear corner of the cabinet.

10" (25.4 cm)

21⁵⁄₁₆"

(54.1 cm)

Centerline of cooktop cutout

" (12.7 mm)

Locate power supply junction box at lower left hand rear corner

NOTES:

■ See cooktop manufacturer’s instructions for cooktop cutout

depth and width.

■ Use dimensions for vent system cutout location that applies

to your installation.

■ Interior-mounted blower systems connect with 3

/4" x 10"

NOTES:

■ See cooktop manufacturer’s instructions for cooktop cutout

depth and width.

■ Exterior-mounted blower systems connect with 10" (25.4 cm)

round vent. The cutout locations for this vent system will depend upon your speciﬁc installation.

(8.3 cm x 25.4 cm) rectangular or 6" (15.2 cm) round vent system. The cutout locations for this vent system will depend on your speciﬁc installation.

Countertop Cutout Dimensions

IMPORTANT: Countertops with a bull-nosed front edge are not recommended for these installations.

Some models require a countertop deeper than 25" (63.5 cm); see the following illustrations. To avoid mistakes, it is recommended that the cooktop and vent cutouts be drawn on the countertop before making any cutouts. See the Cooktop Installation Instructions for complete cutout dimensions, location dimensions, and installation details.

A. Downdraft vent B. Cooktop C. Measurement of cooktop rear overhang

D. D = Measurement of cooktop rear

overhang (C) + 113/16" (46.2 mm) (E) E. 113/16" (46.2 mm) F. ½" (12.7 mm) minimum

G. ¼" (6.4 mm) minimum H. Countertop and backsplash I. ½" (12.7 mm) minimum

A. ½" (12.7 mm) minimum to

backsplash or rear wall

/4" (19.1 mm) maximum

backsplash depth

C. 271/2" (69.9 cm) on 30" (76.2 cm)

models 331/2" (85.9 cm) on 36" (91.4 cm)

models D. D = E + 1 E. Cooktop rear overhang

/16" (46.2 mm)

Electrical Requirements

Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest edition) or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

■ A 120-volt, 60 Hz., AC-only, 15-amp, fused electrical

circuit is required.

■ If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail leads.

2. Connect the aluminum wiring to the added section

of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as speciﬁed on the model/serial/rating plate. The model/serial/rating plate is located on the front of the downdraft vent, above the wiring box cover.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition) or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Venting Requirements

IMPORTANT: Make sure there is proper clearance within the wall or ﬂoor before making exhaust vent cutouts.

■ Use heavy (rigid) metal vent.

■ Venting system must terminate to the outside.

■ Do not terminate the vent system in an attic or other

enclosed area.

■ Do not use 4" (10.2 cm) laundry-type wall caps.

■ Do not install 2 elbows together.

■ Do not use plastic or metal foil vent.

■ The length of vent system and number of elbows should

be kept to a minimum to provide efﬁcient performance.

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than one elbow is used.

■ Use clamps or duct tape to seal all joints in the vent system.

■ Use caulking tape to seal the exterior wall or ﬂoor opening

around cap.

■ Do not cut joist or stud. If vent cutout falls over a joist

or stud, a supporting frame must be constructed.

Flexible metal vent is not recommended. If it is used, calculate each foot of ﬂexible vent as 2 ft (0.6 m) of rigid metal vent.

Flexible elbows count twice as much as standard elbows.

Recommended vent system length:

For either interior-mounted or exterior-mounted blower installations, the vent system length should not exceed the maximum lengths listed in the “Maximum Length of Vent System” chart. See “Calculating Vent System Length” in the “Venting Methods” section in the Installation Instructions for the interior- or exterior-mounted vent motor.

Cold Weather Installations

An additional backdraft damper should be installed to minimize backward cold airﬂow and a thermal break should be installed to minimize conduction of outside temperatures as part of the vent system. The damper should be on the cold air side of the thermal break.

The break should be as close as possible to where the vent system enters the heated portion of the house.

Makeup Air

Local building codes may require the use of makeup air systems when using ventilation systems greater than speciﬁed CFM of air movement. The speciﬁed CFM varies from locale to locale. Consult your HVAC professional for speciﬁc requirements in your area.

INSTALLATION INSTRUCTIONS

INTERIOR-MOUNTED VENT MOTOR

Venting Methods

Determine which venting method is best for your application. Vent system can terminate either through the wall or ﬂoor.

Island Location

Front-Mounted (Standard) Blower Motor

A. Down vent

NOTE: For island locations, a front- or rear-mounted blower motor can also be mounted for right or left venting if needed for your application. Most island applications would still require the venting to be directed down through the ﬂoor.

Rear-Mounted Blower Motor

Built-In Cabinet Locations

Island Location – Vent System Installed Under a Concrete Slab Using PVC Sewer Pipe

Front- (Standard) Mounted Blower Motor

Rear-Mounted Blower Motor

A. Wall cap B. 6" (15.2 cm) round metal vent C. 16" (40.6 cm) maximum

D. 6" (15.2 cm) round PVC sewer pipe E. 6" (15.2 cm) round metal vent transition with damper (supplied) F. 6" (15.2 cm) round PVC coupling G. Concrete slab H. 6" (15.2 cm) round PVC sewer pipe I. 6" (15.2 cm) round 90° PVC sewer pipe elbow J. Tightly pack gravel or sand completely around pipe. K. 6" (15.2 cm) round 90° PVC sewer pipe elbow L. 6" (15.2 cm) round PVC coupling M. 12" (30.5 cm) minimum

Calculating Vent System Length

A. Down vent B. Left vent C. Right vent

3¼" x 10" (8.3 cm x 25.4 cm) rectangular vent is required from the blower motor box. It can be transitioned to 6" (15.2 cm) round vent if needed.

Maximum Length of Vent System

Vent Length

6" (15.2 cm) round 35 ft (8.9 m) 31/4" x 10" (8.3 cm x 25.4 cm) 35 ft (8.9 m)

To calculate the length of the system you need, add the

Cabinet floor

Top of countertop

(73 cm)

equivalent feet (meters) for each vent piece used in the system.

Vent Piece

31/4" x 10" (8.3 cm x 25.4 cm) 90° elbow

31/4" x 10" (8.3 cm x 25.4 cm) Rectangular

5.0 ft (1.5 m)

Example Vent System

6 ft

(1.8 m)

2 ft (0.6 m)

31/4" x 10" (8.3 cm x 25.4 cm) ﬂat elbow

31/4" x 10" (8.3 cm x 25.4 cm) wall cap

12.0 ft (3.7 m)

0.0 ft (0.0 m)

Vent Piece 6" (15.2 cm) Round

45° elbow 2.5 ft

(0.8 m)

90° elbow 5.0 ft

(1.5 m)

6" (15.2 cm) wall cap 0.0 ft

(0.0 m)

31/4" x 10" (8.3 cm x 25.4 cm) to 6" (15.2 cm) transition

4.5 ft (1.4 m)

A. Blower motor B. Transition

C. 90° elbows D. Back draft damper

The following example falls within the maximum vent length of 35 ft (8.9 m).

2 - 90° elbow = 10.0 ft (3 m) 1 - wall cap = 0.0 ft (0.0 m) 8 ft (2.4 m) straight = 8.0 ft (2.4 m) Transition = 4.5 ft (1.4 m) Length of 6" (15.2 cm) or 31/4" x 10"

= 22.5 ft (6.8 m)

(8.3 cm x 25.4 cm) system

Install Vent System

WARNING

Excessive Weight Hazard

Use two or more people to move and install downdraft vent.

Failure to do so can result in back or other injury.

6" (15.2 cm) to 31/4" x 10" (8.3 cm x 25.4 cm) transition

31/4" x 10" (8.3 cm x 25.4 cm) to 6" (15.2 cm) 90° elbow transition

6" (15.2 cm) to 31/4" x 10" (8.3 cm x 25.4 cm) 90° elbow transition

1 ft (0.3 m)

5.0 ft (1.5 m)

1. Place cardboard or similar material on top of a ﬂat surface

where you can easily assemble the downdraft vent system.

2. Remove parts packages, downdraft vent, and blower box

from the carton.

3. Remove all shipping materials, tape, and ﬁlm from the

downdraft vent and blower box.

4. Measure distance “X” from the cabinet ﬂoor to the top of the

countertop. Subtract 281/2" (72.4 cm) from distance “X” to determine dimension “Y” (X - 281/2" = Y).

Downdraft vent

28¹⁄₂"

“X”

“Y”

5. Attach the support legs to the side of the vent box with

“Y”

4 - 4 x 8 mm screws in each support leg. Adjust to dimension “Y” from the bottom of the vent box to the bottom of the support legs. Tighten screws.

Dim.

A. Motor box B. Support leg C. 4 x 8 mm screws (4)

Determine Which Vent Direction Is Best for Your Installation

When installed in a cabinet, vent system can exhaust through the bottom, left, or right of the cabinet.

IMPORTANT: When using the 6" (15.2 cm) vent transition (supplied) for 6" round venting, only left or right venting is recommended.

Bottom Venting:

NOTE: If installing the vent damper in the down position, a wall

or roof cap with a damper at the exit end of the vent system is required.

■ Downdraft vent is shipped with blower in down-venting

position, so no modiﬁcation is required.

■ If rear mounting of the blower motor is not required, go

to the “Complete Installation (Interior-Mounted Motor)” section.

■ To mount the blower motor to the rear side of the vent box,

go to the “Rear Mounting - Blower Motor” section.

Left or Right Venting:

1. Using 2 or more people, place the downdraft vent system

on its back.

2. Remove the 4 screws from the cover plate mounted to the

face of the motor box and set them aside.

A. Cover plate B. Cover plate screws (4) C. Cover plate keyhole slot

shoulder screws (4)

3. Slide the cover plate up and slip it over the keyhole slot

shoulder screws. Set the cover aside.

4. Remove 4 screws from the bottom of the motor box that

hold the motor assembly to the motor box. NOTE: Disconnect the electrical wiring connection from

motor if needed.

5. Remove 3 screws and the vent cover plate from the left

or right side of the motor box for the venting direction to be used.

6. Rotate the blower motor assembly 90° to the left or right side

to the chosen venting direction and secure to the blower box with motor mounting screws previously removed. Do not twist or bind the wires.

7. Install the vent cover plate over the rectangular opening in the

bottom of the motor box and secure with vent cover screws. NOTE: Reinstall the electrical wiring connection to motor

if removed.

8. Reinstall the cover plate to the face of the motor box and

secure with 4 cover plate screws previously removed.

9. For mounting the blower motor to the back of the vent

box, go to the “Rear Mounting - Blower Motor” section. Otherwise, go to the “Complete Installation (Interior-Mounted Motor)” section.

D. Motor mounting screws (4) E. Vent cover plate F. Motor box G. Vent cover screws (3)

Rear Mounting – Blower Motor

C A

NOTE: Optional blower motor rear-mounting position (opposite side) for island cabinet locations. The blower motor box assembly can be moved to the opposite side (rear) of the vent box.

1. Remove 7 screws from the mounting ﬂanges of the blower

motor box.

Front View

A. Screws (7) B. Keyhole slot shoulder screws (2) C. Blower motor box

Rear View

A. Screws (6) B. Keyhole slot shoulder screws (2)

/4" (6.4 mm) deep cover

A. Deep cover

4. Lift the ¼" (6.4 mm) deep cover off the shoulder screws

in the keyhole slots and set the cover aside.

5. Remove the screws from the wire-mounting plate.

A. Blower motor box

2. Lift blower motor box off the shoulder screws in the keyhole

slots. Disconnect wire connection from blower motor and set blower motor box aside.

3. Remove 6 screws from the mounting ﬂange of the ¼" (6.4 mm)

deep cover.

A. Screws B. Wire-mounting plate C. Blower motor box

6. Hold the wire-mounting plate and push the grommet out

of the wire-mounting plate.

A. Wire-mounting plate B. Grommet

7. Slide the wire assembly through the slot in the wire-mounting

plate to remove it.

8. Place the wire assembly through the opening to the opposite

side of the vent box.

9. Reassemble the wire assembly and grommet to the wire-

mounting plate.

10. Install the wire mounting plate to the vent box using the

4 screws previously removed.

11. Place the blower motor box assembly with the keyhole slots

over the 2 shoulder screws on the rear of the vent box and reconnect the wire connection to the blower motor.

12. Mount the blower motor box to the vent box and secure

using the 6 screws previously removed.

14. Remove the front cover from the deep cover, place the front

cover over the previously mounted cover box, and secure using the 4 screws previously removed.

A. Deep cover B. Front cover C. Cover box (supplied)

15. Go to the “Complete Installation (Interior Mounted Motor)”

section.

13. Mount the 43/4" (12.0 cm) cover box (supplied) to the front

of the vent box. Place the keyhole slots over the 2 shoulder screws, align the mounting holes, and secure the cover box to vent box using the 6 screws previously removed from the ¼" (6.4 mm) deep cover.

Complete Installation

(Interior-Mounted Motor)

NOTE: The downdraft vent system is supplied with a 31/4" x 10" (8.3 cm x 25.4 cm) back draft damper and a 6" (15.2 cm) round vent transition with damper. Refer to “31/4" x 10" (8.3 cm x

25.4 cm) Back Draft Damper” or “6" (15.2 cm) Round Vent Transition with Damper,” depending upon the type of venting you are using.

31/4" x 10" (8.3 cm x 25.4 cm) Back-Draft Damper

1. Attach the 3¼" x 10" (8.3 cm x 25.4 cm) back draft damper

to the vent opening in the blower motor box, using three

3.5 x 9.5 mm screws.

A. 3.5 x 9.5 mm screws B. 3¼" x 10" (8.3 cm x 25.4 cm) back-draft damper

2. Remove 4 screws attaching the terminal box cover.

A. Terminal box cover

3. Determine which direction (front or rear) the home power

supply cable will enter the terminal box. Remove the appropriate knockout from the front or rear panel and install a

/2" (12.7 mm) UL listed or CSA approved conduit connector.

4. Using 2 or more people, insert the downdraft vent into the

countertop cutout. Position downdraft vent so it is centered in the cutout with the rear ﬂange over the edge of the cutout and the rear of the vent box against the edge of the cutout.

6" (15.2 cm) Round Vent Transition with Damper

1. Attach the 6" (15.2 cm) round vent transition to vent opening

(left- or right- side venting only is recommended), using two

3.5 x 9.5 mm screws.

A. Rear ﬂange of downdraft vent B. Edge of cutout in countertop C. Rear of downdraft vent

A. 3.5 x 9.5 mm screws B. 6" (15.2 cm) round vent transition with damper

D. Cabinet back

E. Lower support leg F. Cabinet ﬂoor G. Countertop

5. Install the left and right undercounter mounting brackets to

the vent box. Slide the keyhole slots over the guide tabs and push the brackets up to set them in place.

7. Check that the downdraft vent is level as shown below.

Loosen the lower support leg screws and position the legs against the cabinet ﬂoor.

A. Vent box B. Undercounter mounting bracket C. Keyhole slots D. Guide tabs

6. Drill 2 pilot holes through each of the undercounter mounting

brackets into the underside of the countertop. Using 2 screws (not provided) of the appropriate length, mount the brackets to the countertop.

IMPORTANT: Select a screw length that will not allow the screws to go through the countertop when tightened.

A. Screws B. Backsplash C. Countertop

A. Downdraft B. Level

8. Fasten the lower support legs to the cabinet ﬂoor with

screws (not provided).

A. Screw (not provided)

9. Tighten the lower support legs screws.

10. Attach the left and right end caps to the vent box. Place the

tab into the mounting slot at each end of the downdraft vent, as shown, and push down to lock into place.

A. End cap tab B. Mounting slot

Make Electrical Connections

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Feed the power supply cable through the conduit connector

and into the terminal box.

WARNING

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire in terminal box.

Failure to do so can result in death or electrical shock.

3. Connect the green (or green/yellow) ground wire to the green

or yellow/green ground wire using UL listed wire connectors. Tighten the screw on the conduit connector.

4. Connect the 2 white wires together using UL listed wire

connectors.

Check Operation

1. Push and hold the button on the top of the downdraft vent

for a few seconds. The retractable section of the downdraft vent will rise and the blower will be able to start using the control slider. Remove any protective ﬁlm and use a stainless steel cleaner to clean any remaining grease. Position the top trim over the retractable section and snap trim into place.

Trim kits for matching your cooktop color are available from your dealer.

For information on ordering, see the “Assistance or Service” section.

A. Top trim B. On/Off button C. Blower control slider

2. Slide the control slider on the side of vent to check the

operation and speed of the blower.

3. If the blower does not operate:

■ Check that ﬁlter or ﬁlters are pressed in as far as they

will go.

■ Check that the circuit breaker has not tripped or

a household fuse blown.

4. Connect vent system to blower. Vent system must end with

a wall or roof cap. Use clamps or duct tape to seal all joints.

5. Install cooktop according to manufacturer’s instructions.

Check that rear of cooktop overlaps edge of retractable downdraft vent by 3/8" (9.5 mm). See “Countertop Cutout Dimensions” in the “Location Requirements” section.

NOTE: To get the most-efﬁcient use from your new retractable downdraft vent, read the “Vent System Use” section.

D. End cap E. Filters

A. Green or green and yellow

5. Connect the 2 black wires together using UL listed wire

6. Replace the terminal box cover and secure with screw.

7. Reconnect power.

ground wire B. White wires C. UL listed wire connectors

connectors.

D. Black wires E. UL listed or CSA approved

conduit connector

F. Downdraft vent wiring

INSTALLATION INSTRUCTIONS

To attic

blower motor system

in-line blower motor system

To attic installed in-line blower motor system

To attic

blower motor system

in-line blower motor system

EXTERIOR-MOUNTED VENT MOTOR

CAUTION: To reduce the risk of ﬁre and electrical shock, install the downdraft only with remote blower systems that are sold by Whirlpool Corporation. Model numbers UXI0600DYS (600 cfm) and UXI01200DYS (1200 cfm).

Venting Methods

NOTE: Exterior-mounted vent motor installations require an approved in-line blower motor system. Model numbers UXI0600DYS (600 cfm) and UXI1200DYS (1200 cfm) are available from your dealer or authorized parts supplier. See “Blower motor system” in the “Accessories” section.

Determine which venting method is best for your application. Vent system can terminate through the wall or roof. A wall cap or roof cap is required.

NOTES:

■ Venting through a concrete slab is not recommended.

■ The in-line blower motor system must be placed in

an enclosed area and can be located in a utility room, basement, crawl space, or attic. Observe all governing codes and ordinances.

■ 10" (25.4 cm) round vent duct is required for connections to

the retractable downdraft vent system outlet cover and the in-line blower motor inlet and outlet covers. 10" (25.4 cm) round vent duct is recommended for the retractable downdraft vent system with in-line blower motor system. Transitioning to different size ducting will reduce the efﬁciency of the retractable downdraft vent system.

Island Location—

Island Location—Rear Vent

Front Vent

installed in-line

To basement, crawlspace or utility room installed

Built-In Cabinet Locations

installed in-line

To basement, crawlspace or utility room installed

Calculating Vent System Length

It is recommended that you use round vent instead of rectangular vent, especially if elbows are required. If rectangular vent is required, it should be transitioned to 10" (25.4 cm) round vent as soon as possible.

Maximum Length of Vent System

Vent Length

10" (25.4 cm) round 60 ft (18.3 m)

To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.

Vent Piece 6" (15.2 cm) Round

45° elbow 2.5 ft

(0.8 m)

To basement, crawlspace or utility room installed

90° elbow 5.0 ft

(1.5 m)

The maximum equivalent vent lengths of 10" (25.4 cm) round vents - 60 ft (18.3 m).

2 - 90° elbow = 10.0 ft (3 m) 10 ft (3 m) elbows = 10.0 ft (3 m) Length of 10" (25.4 cm) system = 20 ft (6 m)

NOTE: The exterior-mounted vent motor requires a separate wiring cable that should be installed at the same time the vent work is installed.

Install Vent System

Cabinet floor

Top of countertop

(73 cm)

“Y”

WARNING

Excessive Weight Hazard

Use two or more people to move and install downdraft vent.

Failure to do so can result in back or other injury.

1. Place cardboard or similar material on top of a ﬂat surface

where you can easily assemble the downdraft vent system.

2. Remove parts packages, downdraft vent, and blower box

from the carton.

3. Remove all shipping materials, tape, and ﬁlm from the

downdraft vent and blower box.

4. Measure distance “X” from the cabinet ﬂoor to the top of the

countertop. Subtract 281/2" (72.4 cm) from distance “X” to determine dimension “Y” (X - 281/2 = Y).

3. Slide the cover plate up and slip it over the keyhole slot

shoulder screws. Set the cover aside.

4. Install the 10" diameter vent collar plate to the vent box

where the cover plate was removed in the previous step. Secure using the 4 screws from the cover plate.

5. Go to the “Complete Installation (Exterior-Mounted Motor)”

section.

Complete Installation

(Exterior-Mounted Motor)

1. Remove 4 screws attaching the terminal box cover.

Downdraft vent

28¹⁄₂"

“X”

“Y”

5. Attach the support legs to the side of the vent box with

4 - 4 x 8 mm screws in each support leg. Adjust to dimension “Y” from the bottom of the vent box to the bottom of the support legs. Tighten screws.

Dim.

A. Terminal box cover

2. Determine which direction (front or rear) the home power supply

cable and the wiring conduit from the in-line blower system will enter the terminal box. Remove the appropriate knockout from the front or rear panel and install two 1/2" (12.7 mm) UL listed or CSA approved conduit connectors.

3. Using 2 or more people, insert the downdraft vent into the

countertop cutout. Position downdraft vent so it is centered in the cutout with the rear ﬂange over the edge of the cutout and the rear of the vent box against the edge of the cutout.

A. Motor box B. Support leg C. 4 x 8 mm screws (4)

Determine Which Vent Direction Is Best for Your Installation

When installed in a cabinet, vent system can exhaust through the bottom, left, or right of the cabinet. The downdraft vent is shipped with a 10" diameter vent collar plate.

Front or Rear Venting:

1. Using 2 or more people, place the downdraft vent system on

the opposite side for venting.

2. Remove the 4 screws from the cover plate mounted

to the face of the motor box and set them aside.

A. Rear ﬂange of downdraft vent B. Edge of cutout in countertop C. Rear of downdraft vent

D. Cabinet back E. Lower support leg F. Cabinet ﬂoor G. Countertop

+ 42 hidden pages