KitchenAid KVUC606KSS, KVUC600KSS PRODUCT SPECIFICATIONS
DIMENSIONS
RANGE HOOD - 30" (76.2 CM) AND 36" (91.4 CM)
PRODUCT MODEL NUMBERS: KVUC600KSS and KVUC606KSS
1 of 12
WARNING: To reduce the risk of re, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS, located in
your appliance's Owner's Manual, before operating this appliance.
Electrical Requirements:
■ A 120 V, 60 Hz, AC only, 15 A, fused electrical circuit is required.
■ If the house has aluminum wiring, follow the procedure below:
Connect the aluminum wiring using special connectors and/or tools designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local
codes and industry accepted wiring practices.
PRODUCT DIMENSIONS
29/16"
(6.5 cm)
"
3/8
(1.0 cm)
7½"
(19.0 cm)
"
31/
8
(7.9 cm)
30" (76.2 cm)
36" (91.4 cm)
" (74.0 cm): 30" (76.2 cm) models
291/
8
" (89.2 cm): 36" (91.4 cm) models
351/
8
23" (58.4 cm)
FRONT VIEW
12"
(30.5 cm)
10"
(25.4 cm)
W11548781A
DIMENSIONS
RANGE HOOD - 30" (76.2 CM) AND 36" (91.4 CM)
2 of 12
PRODUCT DIMENSIONS
CABINET DIMENSIONS
BA
C
BACK VIEW
Back view 30" (76.2 cm) 36" (91.4 cm)
Unit of Measurement in cm in cm
1
A 1
⁄
2.9 11⁄
8
B 7 17.8 9
C 5/8 1.6 5/8 1.6
30" (76.2 cm) or 36" (91.4 cm)
cabinet opening width
(If installed between cabinets)
8
7
8
⁄
12" (30.5 cm)
2.9
25
Full Width
Chimney Cover (if used)
Minimum cabinet
opening width
Range hood
18" (45.7 cm) minimum
clearance upper
cabinet to countertop
countertop height
Bottom of range hood
to cooking surface
36" (91.4 cm)
X
13" (33.0 cm )
IMPORTANT:
Minimum distance “X” : 24" (61.0 cm) to electric cooking surface and 30" (76.2 cm) to gas cooking surface.
Suggested maximum distance “X” : 36" (91.4 cm).
DIMENSIONS
RANGE HOOD - 30" (76.2 CM) AND 36" (91.4 CM)
3 of 12
A
B
A
B
VENTING REQUIREMENTS
■ Vent system must terminate to the outdoors.
■ Do not terminate the vent system in an attic or other enclosed area.
■ Do not use a 4" (10.2 cm) laundry-type wall cap.
■ Use metal vent only. Rigid metal vent is recommended.
■ The length of vent system and number of elbows should be kept to a minimum to provide efcient performance.
For the most efficient and quiet operation:
■ Use no more than three 90° elbows.
■ Make sure there is a minimum of 24" (61.0 cm) of straight vent between the elbows if more than 1 elbow is used.
■ Do not install 2 elbows together.
■ Use clamps to seal all joints in the vent system.
■ The vent system must have a damper. If roof or wall cap has a damper, do not use damper supplied with the range hood.
■ Use caulking to seal exterior wall or roof opening around the cap.
■ The size of the vent should be uniform.
Venting Methods
This range hood is factory set for venting through the roof or wall.
A 3¹⁄
" x 10" (8.3 cm x 25.4 cm) rectangular vent system is needed for installation (not included). The hood exhaust opening is
4
3¹⁄
"x10" (8.3 cm x 25.4 cm). Vent system can terminate either through the roof or wall. To vent out of the top of the range hood and
4
through a wall, a 90° elbow is needed. See “Install Range Hood” section of your Owner's Manual for details of installing the damper.
NOTE: Flexible vent is not recommended. Flexible vent creates back pressure and air turbulence that greatly reduce performance.
Rear discharge
This range hood can be vented directly out the back using the 3¹⁄4" x 10" (8.3 cm x 25.4 cm) rectangular damper (supplied) along with
a 3¹⁄
" x 10" (8.3 cm x 25.4 cm) rectangular vent system (not supplied). See “Install Range Hood” section of your Owner's Manual for
4
details of installing the damper.
Roof Venting
Wall Venting (top or rear discharge)
A. Roof cap
B. 3¹⁄4" x 10" (8.3 x 25.4 cm)
rectangular metal vent
A. Wall cap
B. 3¹⁄4" x 10" (8.3 x 25.4 cm)
rectangular metal vent
DIMENSIONS
RANGE HOOD - 30" (76.2 CM) AND 36" (91.4 CM)
Calculating Vent System Length
3
" x 10"
(0.6 m)
To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.
" x 10" (8.3 cm x 25.4 cm) Vent System
3¹⁄
4
Vent Piece
3¹⁄
" x 10" (8.3 cm x 25.4 cm)
4
Equivalent Length
5.0 ft (1.5 m)
90° elbow
3
¹⁄
" x 10" (8.3 cm x 25.4 cm)
4
12.0 ft (3.7 m)
at elbow
3
¹⁄
" x 10" (8.3 cm x 25.4 cm)
4
0.0 ft (0.0 m)
wall cap
Example vent system
¹⁄₄
(8.3 x 25.4 cm)
elbow
6 ft (1.8 m)
Wall cap
4 of 12
2 ft
Maximum Recommended Length = 35 ft (10.7 m)
1 - 90° elbow
= 5.0 ft (1.5 m)
8 ft (2.4 m) straight = 8.0 ft (2.4 m)
1 - wall cap = 0.0 ft (0.0 m)
Length of 3
" x 10" (8.3 cm x 25.4 cm)
4
= 13.0 ft (3.9 m)
¹⁄
system
Loading...