KitchenAid KUIS18PNJW3, KUIS18NNJB4, KUIS18NNJB3 Owner’s Manual
Kitchen_kid +
ICE MAKER
For questions about features, operation/performance, parts accessories or service, call: 1-800-422-1230
In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...
www.kitchenaid.com or www.kitchenaid.com/canada
MACHINE A GLA( ONS
J: /_ !' +_; + . ; 1
(:+,I. _i)I++._:_.I o+._iI i7, [+9 _i)I]
Au Canada, pour assistance composez le 1-800-461-5681, pour installation ou service composez le 1-800-867-6777 ou visitez notre site web &...
www.kitchenaid.com/canada
Table of Contents/Table des matieres ............................................................................. 2
2217251
TABLE OF CONTENTS
TABLE DES MATIERES
ICE MAKER SAFETY .................................................................. 3
ICE MAKER INSTALLATION ......................................................... 4
Unpacking .................................................................................... 4
Location Requirements ................................................................ 4
Electrical Requirements ............................................................... 4
Leveling the Ice Maker ................................................................. 5
Water Supply Connection ............................................................ 5
Normal Sounds ............................................................................ 7
ICE MAKER USE ............................................................................ 8
How Your Ice Maker Works ......................................................... 8
Using the Controls ....................................................................... 8
ICE MAKER CARE .......................................................................... 8
Cleaning ........................................................................................ 8
Changing the Light Bulb ............................................................ 11
Vacation and Moving Care ......................................................... 11
TROUBLESHOOTING .................................................................. 12
ASSISTANCE OR SERVICE ......................................................... 13
In the U.S.A ................................................................................ 13
In Canada ................................................................................... 13
WARRANTY .............................................................................. 14
S¢:CURIT¢ DE LA MACHINE A GLAQONS ............................. 15
INSTALLATION DE LA MACHINE A GLAQONS ........................ 16
Deballage .................................................................................... 16
Emplacement d'installation ........................................................ 16
Specifications electriques .......................................................... 16
Nivellement ................................................................................. 17
Raccordement de la canalisation d'eau .................................... 17
Sons normaux ............................................................................ 20
UTILISATION DE LA MACHINE A GLAgONS ............................ 20
Fonctionnement de la machine a glagons ................................ 20
Utilisation des commandes ........................................................ 21
ENTRETIEN DE LA MACHINE ._,GLAQONS .............................. 21
Nettoyage ................................................................................... 21
Changement de I'ampoule d'eclairage ...................................... 23
Precautions a prendre pour les vacances
ou le demenagement .................................................................. 24
DCPANNAGE ................................................................................. 25
ASSISTANCE OU SERVICE ......................................................... 26
Aux 12tats-Unis............................................................................ 26
Au Canada .................................................................................. 26
GARANTIE ................................................................................. 27
ICE MAKER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or
This is the safety alert symbol.
"WARNING." These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic
precautions:
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before cleaning.
• Disconnect power before servicing.
• Replace all panels before operating.
• Use two or more people to move and install ice maker.
SAVE THESE INSTRUCTIONS
ICE MAKER
INSTALLATION
Excessive Weight Hazard
Use two or more people to move and install
ice maker.
Failure to do so can result in back or other injury.
NOTE: Do not kink or pinch the power supply cord between
the ice maker and cabinet.
34"
(86.4cm)
Min.
341/2 "
(87.6cm)
Max.
281/2''
(72.4 cm)
Removing packaging materials
Remove tape and glue from your ice maker before using.
• To remove any remaining tape or glue, rub the area briskly
with your thumb. Tape or glue residue can also be easily
removed by rubbing a small amount of liquid dish soap over
the adhesive with your fingers. Wipe with warm water and
dry.
• Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your ice maker.
Cleaning before use
After you remove all of the packaging materials, clean the inside
of your ice maker before using it. See the cleaning instructions in
the "Ice Maker Care" section.
To ensure proper ventilation for your ice maker, the front side
must be completely unobstructed. The unit may be closed-in
on the top and three sides, but the installation should allow
the ice maker to be pulled forward for servicing if necessary.
Installation of the ice maker requires a cold water supply inlet
of 1/4in. (6.35 mm) OD soft copper tubing with a shut-off valve
and either a gravity-drain system or condensate pump to
carry the water to an existing drain.
Choose a well ventilated area with temperatures above 55°F
(13°C) and below 100°F (38°C). Best results are obtained
between 70°F (21°C) and 90°F (32°C). This unit MUST be
installed in an area protected from the elements, such as
wind, rain, water spray or drips.
When installing the ice maker under a counter, follow the
recommended opening dimensions shown. Place electrical
and plumbing fixtures in the recommended location as
shown.
}-_ 18"'_
(45.7 crn)
1.Recommended location for electrical and plumbing fixtures.
2. Floor level
You should choose a location where the floor is even. It is
important for the ice maker to be level in order to work
properly. If needed, you can adjust the height of the ice maker
by changing the position of the rear wheels. See the
"Leveling" section.
. ,_j _...=_I +>............ <..== i_=
I
Electrical Shock Hazard
Plug into a grounded 3 prong outet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Falute to folow these instructions can resuJt in
death, fire, or eJectricaJ shock.
Before you move your ice maker into its final location, it is
important to make sure you have the proper electrical
connection:
A 115 Volt, 60 Hz., AC only 15 ampere electrical supply, properly
grounded in accordance with the National Electrical Code and
local codes and ordinances, is required.
It is recommended that a separate circuit, serving only your ice
maker, be provided. Use a receptacle which cannot be turned off
by a switch or pull chain.
Recommended grounding method
For your personal safety, this appliance must be grounded. This
appliance is equipped with a power supply cord having a 3 prong
grounding plug, To minimize possible shock hazard, the cord
must be plugged into a mating, 3 prong, grounding-type wall
receptacle, grounded in accordance with the National Electrical
Code and local codes and ordinances, If a mating wall receptacle
is not available, it is the personal responsibility of the customer to
have a properly grounded, 3 prong wall receptacle installed by a
qualified electrician.
It is important for the ice maker to be level in order to work
properly. Depending upon where you install the ice maker, you
may need to make several adjustments to level it.
Tools required
• Carpenter's level
• Adjustable wrench
• ¼in. sock_wrench
Undercounter installation
If you are installing the ice maker under a countertop, then you
may need to adjust the height of the ice maker. The adjustable
rear wheels are preset to position 1 for a cabinet opening height
of 34 in. (86.4 cm).
To adjust the front leveling legs
Your ice maker has two adjustable leveling legs to help you
steady the product and make sure it is level.
NOTE: It is easier to adjust the leveling legs if you have another
person to assist you,
1. Place a carpenter's level on top of the product to see if the ice
maker is level from front to back and side to side.
2. Push up on the top front of the ice maker, and then locate the
leveling screws that are on the bottom front of the product.
3. Using an adjustable wrench, change the height of the legs as
follows:
• Turn the leveling leg to the right to lower that side of the
ice maker.
• Turn the leveling leg to the left to raise that side of the ice
maker.
NOTE: The ice maker should not wobble. Use shims to add
stability when needed.
4.
Use a carpenter's level to re-check the ice maker to see that it
is even from front to back and side to side. If the ice maker is
not level, repeat Steps 2 and 3. If the ice maker is level, go to
the "Water Supply Connection" section.
1. For cutout height of 34 in. (86.4 cm)
2. For cutout height of 34V8 in. (86.7 cm)
3. For cutout height of 34s/_Gin. (87.2 cm)
4. For cutout height of 34V2 in. (87.6 cm)
To adjust the rear wheel height
1. Using a 1/4in. socket wrench, remove the five screws from the
rear access panel and carefully pull the panel away from the
drain hose.
2. Using a % in. or adjustable wrench, remove the screw that
holds the rear wheel.
NOTE: Push up against the top back of the ice maker to take
some weight off of the wheels and make it easier to remove
the screws.
3. Move the rear wheel and screw to a new position as needed
for your cabinet opening height. Tighten the screw
completely.
4. Repeat Steps 2 and 3 to change the position of the wheel on
the other side.
5. Replace the rear panel and screws. Be sure that the drain
tube is positioned in the opening provided,
6. Use the front leveling legs to make sure the product is level.
Freestanding installation
If you are not installing your ice maker under a countertop, you
will probably not need to adjust the rear wheel height. Follow the
steps outlined in "To adjust the front leveling legs" earlier in this
section.
NOTE: The ice maker should not wobble, Use shims to add
stability when needed.
Read all directions carefully before you begin.
IMPORTANT:
• All installations must be in accordance with local plumbing
codes requirements.
• Use copper tubing and check for leaks.
• Install copper tubing only in areas where temperatures will
remain above freezing.
Tools required:
• Standard screwdriver
• 7/16in. and 1/2in. open-end wrenches or two adjustable
wrenches
• ¼in. nut driver
• ¼in. drill bit
• Hand drill or electric drill properly grounded
NOTE: Your ice maker dealer has a kit available with a 1/4in.
(6.35 mm) saddle-type shut-off valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or 3_6in.
(4.76 mm) saddle valve which reduces water flow and clogs more
easily.
Connecting the water line:
REAR VIEW
Turn off main water supply. Turn on nearest faucet long
enough to clear line of water.
2.
Find a 1/2in. (12.70 mm) to 11/4in. (3.18 cm) vertical cold water
pipe near the ice maker.
NOTE: Horizontal pipe will work, but the following procedure
must be followed: Drill on the top side of the pipe, not the
bottom. This will help keep water away from the drill. This
also keeps normal sediment from collecting in the valve.
3. Using a grounded drill, drill a 1/4in. (6.35 mm) hole in the cold
water pipe you have selected.
4. Fasten shut-off valve to cold water pipe with pipe clamp. Be
sure outlet end is solidly in the 1/4in. (6.35 mm) drilled hole in
the water pipe and that washer is under the pipe clamp.
Tighten packing nut. Tighten the pipe clamp screws carefully
and evenly so washer makes a watertight seal. Do not
overtighten the pipe clamp or you may crush cold water pipe
if it is soft copper tubing. Do not use a piercing-type or 3_6in.
(4.76 mm) saddle-type valve which reduces water flow and
clogs more easily.
5. Now you are ready to connect the copper tubing. Use 1/4in.
(6.35 mm) OD soft copper tubing for the cold water supply.
• Measure from the connection at the front of the ice maker
to the cold water pipe. Add 3 ft (91.4 cm) to ensure that
you have the proper length. This is the length of 1/4in.
(6.35 mm) OD soft copper tubing you need for the job. Be
sure both ends of the copper tubing are cut square.
• Slip compression sleeve and compression nut on copper
tubing as shown. Insert end of tubing into outlet end
squarely as far as it will go. Screw compression nut onto
outlet end with adjustable wrench. Do not overtighten.
I
!. Drain Hose (Drain Pump models only)
2. Vent Hose (Drain Pump models only)
3. Water Supply Line
9. Bend the copper tubing to meet the water valve inlet on the
water valve which is located in the front of the ice maker
cabinet as shown.
10. Thread the provided nut onto the coupling on the end of the
copper tubing. Tighten the nut by hand. Then tighten it with a
wrench two more turns. Do not overtighten.
1 2 3 4 3 2
!. Line to ice maker 3. Ferrule (purchased)
2. Nut (provided) 4. Coupling (purchased)
8 ......... ...................2
......43 5
1.Cold Water Pipe 5. Compression Nut
2. Pipe Clamp 6. Compression Sleeve
3. Copper Tubing 7.Shut-Off Valve
4. Coupling (purchased) 8. Packing Nut
6=
Place the free end of the tubing into a container or sink, and
turn on main water supply and flush out tubing until water is
clear. Turn off shut-off valve on the water pipe.
NOTE: Always drain the water line before making the final
connection to the inlet of the water valve to prevent possible
water valve malfunction.
7.
Remove the two screws in the lower access panel and the
two screws in the base grille area of the front panel support.
Pull forward to remove the lower access panel.
8=
Position the tubing so it can enter one of the two access
holes located at the right-hand rear of the cabinet as shown.
The tubing should extend beyond the cabinet front when the
cabinet is pushed back into position. Move the ice maker into
position.
11. Unscrew the water valve inlet cover, and attach the copper
tubing with the compression sleeve and nut.
NOTE: To prevent rattling, be sure the copper tubing does not
touch the cabinet's side wall or other parts inside the cabinet.
FRONT VIEW
151/4"
I_'_ (38.7 cm)
i
(I 4.5 cm)
813/16"
(22.4 cm)
27/8" (7.27 cm)
1. WaterPanDrain
2. WaterValve
12. Turn shut-off valve on.
13. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
NOTE: The ice maker is equipped with a built-in water
strainer. If local water conditions require periodic cleaning or
a well is your source of water supply, a second water strainer
should be installed. Obtain a water strainer from your nearest
appliance dealer and install it at either tube connection.
14. Replace the lower access panel and screws.
Connecting the drain
Gravity drain system
Connect the ice maker drain to your drain in accordance with all
state and local codes and ordinances. Ifthe ice maker is
provided with a gravity drain system, follow these guidelines
when installing drain lines. This will prevent water from flowing
back into the ice maker storage bin and potentially flowing onto
the floor causing water damage.
• Drain lines must have a minimum of % in. (15.88 mm) inside
diameter.
Drain lines must have a 1in. drop per48 in. (2.54 cm drop per
122 cm) of run or 1/4in. drop per 12 in. (6.35 mm per
30.48 cm) and must not have low points where water can
settle.
• The floor drains must be large enough to accommodate
drainage from all drains.
The ideal installation has a 11/2in. (3.81 cm) standpipe
installed directly below the outlet of the drain tube as shown.
You must maintain a 1 in. (2.54 cm) air gap between the drain
pump hose and the standpipe.
• It may be desirable to insulate the drain line thoroughly up to
the drain inlet.
After ensuring that the drain system is adequate, follow these
steps to properly place the ice maker:
1. Plug in ice maker or reconnect power.
2. Re-check the ice maker to be sure that it is level. See the
"Leveling" section.
3. Push the ice maker into position so that the ice maker drain
tube is positioned over the standpipe.
SIDE VIEW
4. If it is required by your local sanitation code, seal the cabinet
to the floor with an approved caulking compound after all
water and electrical connections have been made.
Drain pump system (on some models}
Connect the drain pump hose (provided with the product) to your
drain in accordance with all state and local codes and
ordinances.
NOTE: If the drain hose becomes twisted and water cannot
drain, your ice maker will not work.
Your new ice maker may make sounds that are not familiar to
you. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard
surfaces like the floor, walls and cabinets can make the sounds
seem louder than they actually are. The following describes the
kinds of sounds that might be new to you and what may be
making them.
• You will hear a buzzing sound when the water valve opens to
fill the water reservoir for each cycle.
• Rattling noises may come from the flow of the refrigerant or
the water line. Items stored on top of the ice maker can also
make noises.
• The high efficiency compressor may make a pulsating or high
pitched sound.
• Water running over the evaporator plate may make a
splashing sound.
• Water running from the evaporator plate to the water reservoir
may make a splashing sound.
• As each cycle ends, you may hear a gurgling sound due to
the refrigerant flowing in your ice maker.
• You may hear air being forced over the condenser by the
condenser fan.
• During the harvest cycle, you may hear a "thud" when the ice
sheet slides from the evaporator onto the cutter grid.
• When you first start the ice maker, you may hear water
running continuously. The ice maker is programmed to run a
rinse cycle before it begins to make ice.
1. Drain Hose
2. 1 in. (2.54 cm) Air Gap
3. Standpipe
4. Center of drain should be 20 in. (50.80 cm)
from front of door.
ICE MAKER USE
5.
Cubes fall into the storage bin. When the bin is full, the ice
maker shuts off automatically and restarts when more ice is
needed. The ice bin is not refrigerated and some melting will
occur. The amount of melting varies with room temperature.
_ _ _ _ _ _ - _ _ ......
When you first start your ice maker, the water pan will fill and the
system will rinse itself before starting to make ice. The rinsing
process takes about five minutes.
Under normal operating conditions, the ice maker will cycle at
preset temperatures. The ice level sensor located in the ice
storage bin will monitor the ice levels.
IMPORTANT:
• If the water supply to the ice maker is turned off, be sure to
set the ice maker control to OFE
• The ice maker is designed to make clear ice from the majority
of water sources on a daily basis. Ifyour results are
unsatisfactory, your water may need to be filtered or treated.
The Ice Making Process
1. Water is constantly circulated over afreezing plate. As the
water freezes into ice, the minerals in the water are rejected.
This produces a clear sheet of ice with a low mineral content.
i akei
%
NOTE: As the room and water temperatures vary, so will the
amount of ice produced and stored. This means that higher
operating temperatures result in reduced ice production.
1. To start the normal ice making cycle, select ON.
2. To stop ice maker operation, select OFF.
CLEANING
NOTE: The CLEAN setting is used whenever solutions are
circulated through the ice maker for cleaning. Only the water
pump and compressor operate at this setting. See the "Cleaning
Ice Maker System" section.
2. When the desired thickness is reached, the ice sheet is
released and slides onto a cutter grid. The grid divides the
sheet into individual cubes.
3. The water containing the rejected minerals is drained after
each freezing cycle.
4. Fresh water enters the machine for the next ice making cycle.
ICE MAKER CARE
The ice making system and the air cooled condenser need to be
cleaned regularly for the ice maker to operate at peak efficiency
and to prevent premature failure of system components.See the
"Cleaning Ice Maker System" and the "Cleaning the Condenser"
sections.
Exterior Surfaces
Wash the exterior enamel surfaces and gaskets with warm water
and mild soap or detergent. Wipe and dry. Regular use of a good
household appliance cleaner and wax will help protect the finish.
Do not use abrasive cleaners on enamel surfaces as they may
scratch the finish.
For products with a stainless steel exterior, use a clean sponge or
soft cloth and a mild detergent in warm water. Do not use
abrasive or harsh cleaners.
Ice Maker System
Condenser
Minerals that are removed from water during the freezing cycle
will eventually form a hard scaly deposit in the water system.
Cleaning the system regularly helps remove the mineral scale
buildup. How often you need to clean the system depends upon
how hard your water is. With hard water of 15 to 20 grains/gal. (4
to 5 grains/liter), you may need to clean the system as often as
every 6 months.
NOTE: Use one 16 oz (473 mL) bottle of NU-CALGON* Nickel
Safe Ice Machine Cleaner. To order, call 1-800-442-9991 and ask
for Part Number 8171307. In Canada, call 1-800-807-6777.
1. Push the selector switch to OFR
2. Wait 5 to 10 minutes for the ice to fall into the storage bin.
Remove all ice from the storage bin.
3. Unscrew the drain cap from the bottom of the water pan
located inside the storage bin as shown. Allow the water to
drain completely.
4. Replace the drain cap securely on the water pan. If the drain
cap is loose, water will empty from the water pan and you will
have either thin ice or no ice.
5. Read and follow all handling information on the cleaner bottle
before completing the steps below. Use one 16 oz (473 mL)
bottle of NU-CALGON* Nickel Safe Ice Machine Cleaner.
6. Pour one bottle of solution into the water pan. Fill the bottle
twice with tap water and pour it into the water pan.
A dirty or clogged condenser:
• Prevents proper airflow.
• Reduces ice making capacity.
• Causes higher than recommended operating temperatures
which may lead to component failure.
ElectricaJ Shock Hazard
Disconnect power before cJeaning.
Replace aH pane_s before operating.
Failure to do so can resuJt in death or
etectricaJ shock.
1. Unplug ice maker or disconnect power.
2. Remove the two screws in the lower access panel and the
two screws from the base grille area of the front panel
support. Pull forward to remove the lower access panel.
3. Pull the bottom forward and then pull down to remove the
lower access panel.
!. Water Pan
2. Drain Cap
7.
Push the selector switch to CLEAN. (See the "Using the
Controls" section.) The light will turn on, indicating that the
cleaning cycle is in process. When the indicator light turns off
(approximately 45 minutes), the cleaning cycle is complete.
During the cleaning cycle, the system will both clean and
rinse itself.
8. After the cleaning cycle is complete, remove the drain cap
from the water pan to see if any cleaning solution is left in the
water pan. If cleaning solution drains from the water pan, you
should run the clean cycle again. Be sure to replace the drain
cap securely on the water pan. If the drain cap is loose, water
will empty from the water pan and you will have either thin ice
or no ice.
NOTE: Severe scale buildup may require repeated cleaning with
a fresh quantity of cleaning solution.
9. Push the selector switch to ON to resume ice production.
*Nu-Calgon is a trademark of Calgon Corporation.
!. Lower Access Panel Screws
2. BaseGrille Screws
4.
Remove dirt and lint from the condenser fins and the unit
compartment with a brush attachment on a vacuum cleaner.
5. Replace the lower access panel using the four screws.
6. Plug in ice maker or reconnect power.
Loading...