KitchenAid KUIS185JWH0 Owner's Manual
ICE MAKER
Use & Care Guide
For questions about features, operation/performance, parts accessories or service, call: 1-800-422-1230
In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...
www.kitchenaid.com or www.kitchenaid.com/canada
LA MACHINE À GLAÇONS
Guide d’utilisation et d’entretien
Au Canada, pour assistance composez le 1-800-461-5681, pour installation o u service, composez le 1-800-807-6777 ou visitez notre site web à...
Tabl e of Contents/Table des matières................................ ...... ...................... 2
www.kitchenaid.com/canada
2208388
TABLE OF CONTENTS
TABLE DES MATIÈRES
ICE MAKER SAFETY.................................................................. 3
INSTALLING YOUR ICE MAKER ..................................................4
Location Requirements................................................................ 4
Unpacking the Ice Maker............................................................. 4
Electrical Requirements ...............................................................4
Leveling the Ice Maker .................................................................5
Connecting the Ice Maker to a Water Source .............................5
Understanding Sounds You May Hear........................................7
USING YOUR ICE MAKER ............................................................7
Understanding How Your Ice Maker Works................................7
Setting the Controls .....................................................................8
CARING FOR YOUR ICE MAKER................................................. 8
Cleaning Exterior Surfaces........................................................... 8
Cleaning the Ice Maker System................................................... 8
Cleaning the Condenser ..............................................................9
Cleaning the Interior Components...............................................9
Changing the Light Bulb ............................................................10
Vacation and Moving Care......................................................... 10
TROUBLESHOOTING ..................................................................11
ASSISTANCE OR SERVICE.........................................................12
WARRANTY ..................................................................................13
SÉCURITÉ DE LA MACHINE À GLAÇONS .............................14
INSTALLATION DE LA MACHINE À GLAÇONS........................15
Emplacement d’installation........................................................15
Déballage de la machine à glaçons ...........................................15
Spécifications électriques ..........................................................15
Mise d’aplomb de la machine à glaçons ...................................16
Raccordement de la machine à glaçons
à l’alimentation en eau ...............................................................16
Compréhension des bruits que vous pouvez entendre ............18
UTILISATION DE LA MACHINE À GLAÇONS............................18
Compréhension du fonctionnement de la machine à glaçons.18
Réglage des commandes ..........................................................19
ENTRETIEN DE LA MACHINE À GLAÇONS..............................19
Nettoyage des surfaces extérieures ..........................................19
Nettoyage du système de la machine à glaçons.......................20
Nettoyage du condenseur..........................................................20
Nettoyage des composants intérieurs.......................................21
Changement de l’ampoule d’éclairage......................................21
Précautions à prendre pour les vacances
ou le déménagement..................................................................22
DÉPANNAGE.................................................................................22
ASSISTANCE OU SERVICE.........................................................23
GARANTIE.....................................................................................24
2
ICE MAKER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
precautions
■ Plug into a grounded 3 prong outlet.
■ Do not remove ground prong.
■ Do not use an adapter.
■ Do not use an extension cord.
: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic
:
■ Disconnect power before cleaning.
■ Disconnect power before servicing.
■ Replace all panels before operating.
■
Use two or more people to move and install
ice maker.
SAVE THESE INSTRUCTIONS
3
INSTALLING YOUR ICE
Unpacking the Ice Maker
MAKER
Location Requirements
■ To ensure proper ventilation for your ice maker, the front side
must be complete ly unob s truc t ed. T he unit may be closed -in
on the top and three sides, but the installation should allow
the ice maker to be pulled forward for servicing if necessary.
■ Installation of t he ic e ma ke r requir es a c o ld wate r supply inlet
of ¹⁄₄ in. (6.3 5 mm) OD soft copper tubing with a shut-of f valv e
and either a gravity-drain system or condensate pump to
carry the water to an existing drain.
■ Choose a well ventilated area with temperatures above 55°F
(13 °C) and below 100°F (3 8°C). Best results are obtained
between 70°F (21°C) and 90°F (3 2°C). This unit MUST b e
installed in an area protected from the elements, such as
wind, rain, water spray, or drip.
■ When installing the ice ma ker under a counter, follow the
recommended opening dimensions shown. Place electrical
and plumbing fixtures in the recommended location as
shown.
NOTE: Do not kink or pinch the power supply cord between
the ice maker and cabinet.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
ice maker.
Failure to do so can result in back or other injury.
Removing packaging materials
Remove tape and glue from your ice maker before using.
■ To remove any remaining tape or glue, rub the area briskly
with your thumb. Tape or glue residue can also be easily
removed by rubbing a small amount of liquid dish soap over
the adhesive with your fingers. Wipe with warm water and
dry .
■ Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your ice maker.
Cleaning before use
After you remove all of the packaging materials, clean the insid e
of your ice maker before using it. See the cleaning instructions in
the “Caring for Your Ice Maker” section.
Electrical Requirements
1/2
14
"
(36.8 cm)
34"
(86.4 cm)
Min.
1/2
34
"
(87.6 cm)
Max.
1. Recommended location for electrical and
plumbing fixtures.
2. Floor level
■ You should choose a location where the floor is even . It is
1/2
3
(8.9 cm)
24"
(60.1 cm)
(45.7 cm)
"
18"
9"
(22.9 cm)
1/2
28
"
(72.4 cm)
important for the ice maker to be level in order to work
properly . If needed, you can adjust the height of the ice maker
by changing the position of the rear wheels. See the “Leveling
the Ice Maker” section.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Before you move your ice maker into its final location, it is
important to make sure you have the proper electrical
connection:
A 115 Volt, 60 Hz., AC only 15 ampere electrical supply, properly
grounded in accordance with the National Electrical Code and
local codes and ordinances, is required.
It is recommended that a separate ci rcuit, serving only your ice
maker, be provided. Use a receptacle which cannot be turned off
by a switch or pull chain.
4
Recommended grounding method
For your personal safety, this appliance must be grounded. This
appliance is equipped with a power supply cord having a 3 prong
grounding plug. To minimize possible shock hazard, the cord
must be plugged into a mating, 3 prong, grounding-type wall
receptacle, grounded in accordance with the National Electrical
Code and local codes and ordinances. If a mating wall receptacle
is not available , it is the p ersonal resp onsib ility of th e custome r to
have a properly grounded, 3 prong wall receptacle installed by a
qualified electrician.
Leveling the Ice Maker
It is important for the ice maker to be level in order to work
properly. Depending upon where you install the ice maker, yo u
may need to make several adjustments to level it.
Tools required
■ Carpenter’s level
■ Adjustable wrench
■ ¹⁄₄" socket wrench
Undercounter installation
If you are installing the ice maker under a countertop, then you
may need to adjust the height of the ice maker. The adjustable
rear wheels are preset to position 1 for a cabinet opening height
of 3 4" (86.4 cm).
To adjust the front leveling legs
Your ice maker has two adjustable leveling legs to help you
steady the product and make sure it is level.
SUGGESTION:
another person to assist you.
Place a carpenter’s level on top of the product to see if the ice
1.
maker is level from front to back and side to side.
Push up on the t op front of the ice make r, and then locate the
2.
leveling screws that are on the bottom front of the product.
Using an adjustable wrench, change the height of the legs as
3.
follows:
■ Turn the leveling leg to the right to lower that side of the
ice maker.
■ Turn the levelin g leg to the le f t to rais e that side of the ic e
maker.
NOTE:
stability when needed.
Use a carpenter’s level to re-check the ice maker to see that it
4.
is even from front to back and side to side. If the ice maker is
not level, re p e at Ste p s 2 an d 3. If the ice ma ke r is le v el, go to
the “Connecting the Ice Maker to a Water Source” section.
It is easier to adjust the leveling legs if you have
The ice maker should not wobble. Use shims to add
1. For cutout height of 34" (86.4 cm)
2. For cutout height of 34
3. For cutout height of 34
4. For cutout height of 34
" (86.7 cm)
¹⁄₈
" (87.2 cm)
⁵⁄₁₆
" (87.6 cm)
¹⁄₂
To adjust the rear wheel height
Using a ¹⁄₄" socket wrench, remove the five screws from the
1.
rear access panel and carefully pull the panel away from the
drain hose.
Using a ³⁄₈" or adjustable wrench, remove the screw that
2.
holds the rear wheel.
Pushing up against the top back of the ice maker
NOTE:
takes some of the weight off of the wheels. This makes it
easier to remove the screws.
Move the rear wheel and screw to a new position as needed
3.
for your cabinet opening height. Tighten the screw
completely.
Repeat Steps 2 and 3 to change the position of the wheel on
4.
the other side.
Replace the rear panel and screws. Be s ure that the drain
5.
tube is positioned in the opening provided.
Use the front leveling legs to make sure the product is level.
6.
Freestanding installation
If you are not installing your ice maker under a countertop, you
will probably not need to adjust the rear wheel height. Follow the
steps outlined in “To adjust the front leveling legs” earlier in this
section.
The ice maker should not wobble. Use shims to add
NOTE:
stability when needed.
Connecting the Ice Maker to a Water
Source
Read all directions carefully before you begin.
IMPORTANT:
■ All installations must be in accordance with loca l plumbing
codes requirements.
■ Use copper tubing and check for leaks.
■ Install copper tubi ng only in areas where temperatures will
remain above freezing.
Tools required:
■ Standard screwdriver
■ ⁷⁄₁₆ in. and ¹⁄₂ in. open-end wrenches or two adjustable
wrenches
■ ¹⁄₄ in. nut driver
■ ¹⁄₄ in. drill bit
■ Hand drill or electric drill properly grounded
Your ice maker dealer has a kit available with a
NOTE:
¹⁄₄ in. (6.3 5 mm) saddle-type shut-off valve, a union, and copper
tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes. Do not use a piercingtype or ³⁄₁₆ in. (4.76 mm) saddle valve which reduces water flow
and clogs more easily.
5
Connecting the water line:
Turn
1.
enough to clear line of water.
Find a ¹⁄₂ in. (12.70 mm) to 1¹⁄₄ in. (3 .18 cm) vertical
2.
pipe near the ice maker.
NOTE:
must be followed: Drill on the top side of the pipe, not the
bottom. This will help keep water away from the drill. This
also keeps normal sediment from collecting in the valve.
Using a grounded drill, drill a ¹⁄₄ in. (6.3 5 mm) hole in the cold
3.
water pipe you have selected.
Fasten shut-off valve to cold water pipe with pipe clamp. Be
4.
sure outlet end is solidly in the ¹⁄₄ in. (6.3 5 mm) drilled hole in
the water pipe and that washer is under the pipe clamp.
Tighten packing nut. Tighten the pipe clamp screws carefully
and evenly so washer makes a watertight seal. Do not
overtighten the pipe clamp or you may crush cold water pipe
if it is soft copper tubing. Do not use a piercing-type or ³⁄₁₆ in.
(4.76 mm) saddle-type valve which reduces water flow and
clogs more easily.
Now you are ready to connect the copper tubing. Us e ¹⁄₄ in.
5.
(6.3 5 mm) OD soft copper tubing for the cold water supply.
■ Measure from the connection at the front of the ice maker
■ Slip compression sleeve and compression nut on copper
main water supply. Turn on nearest faucet long
off
cold
Horizontal pipe will work, but the following procedure
to the cold wate r pip e. Ad d 3 feet to ensu re that you have
the proper le ngth. This is t he lengt h of ¹⁄₄ in. (6.3 5 mm) OD
soft copper tubing you need for the job. Be sure both
ends of the copper tubing are cut square.
tubing as shown. Insert end of tubing into outlet end
squarely as far as it will go. Screw compression nut onto
outlet end with adjustable wrench. Do not overtighten.
water
Remove the two screws in the lower access panel and the
7.
two screws in the base grille area of the front panel support.
Pull forward to remove the lower access panel.
Position the tubing so it can enter one of the two ac ces s
8.
holes located at the right-hand rear of the cabinet as shown.
The tubing should ex tend beyond the cabinet front when the
cabinet is pushed back into position. Move the ice maker into
position.
REAR VIEW
1. Upper Water Line Access Hole
2. Lower Water Line Access Hole
Bend the copper tubing to meet the water valve inlet on the
9.
water valve which is located in the front of the ice maker
cabinet as shown.
Unscrew the water valve inlet cover, and attach the copper
10.
tubing with the co mpression sl ee v e and nut.
To prevent rattling, be sure the copper tubing does not
NOTE:
touch the cabine t’s side wall or other parts insi de the c abinet.
FRONT VIEW
1. Cold Water Pipe
2. Pipe Clamp
3. Copper Tubing
4. Compression Nut
5. Compression Sleeve
6. Shut-Off Valve
7. Packing Nut
Place the free end of the tubing into a container or sink, and
6.
turn on main water supply and flush out tubing until water is
clear. Turn
NOTE:
shut-off valve on the water pipe.
off
Always drain the water line before making the final
connection to the inlet of the water valve to prevent possible
water valve malfunction.
1/4"
15
(38.7 cm)
"
7/8
2
" (7.27 cm)
1. Water Pan Drain
2. Water Valve
11. Turn shut-off valve on. Check for leaks.
Tighten any
connections (including connections at the valve) or nuts that
leak. The ice maker is equipped with a built-in water strainer.
If local water conditions require periodic cleaning or a well is
your source of water supply, a second water strainer should
be installed. Obtain a water strainer from your nearest
appliance dealer and install it at either tube connection.
Replace the lower access p anel and screws.
12.
6
Connecting the drain
2
4
3
Gravity drain system
Connect the ice maker drain to y our drain in accordance with all
state and local codes and ordinances. If the ice maker is
provided with a gravity drain system, follow these guidelines
when installing drain lines. This will prevent water from flowing
back into the ice maker storage bin and potentially flowing onto
the floor causing water damage.
■ Drain lines must have a minimum of ⁵⁄₈ in. (15.88 mm) inside
diameter.
■ Drain lines must have a 1 in. drop per 48 in. (25.40 mm drop
per 122 cm) of run or ¹⁄₄ in. drop per 12 in. (6.3 5 mm per
3 0.48 cm) and must not have low points where water can
settle.
■ The floor drains must be large enough to accommodate
drainage from all drains.
■ The ideal installation has a 1¹⁄₂ in. (3 .81 cm) standpipe
installed directly below the outlet of the drain tube as shown.
You must maintain a 1 in. (25.40 mm) air gap between the
drain pump hose and the stan dpipe.
■ It may be desirable to insulate the drain line thoroughly up to
the drain inlet.
After ensuring that the d rain system is adequate, follow these
steps to properly place the ice maker:
Plug in ice maker or reconn e ct powe r.
1.
Re-check the ice maker to be sure that it is level. See the
2.
“Leveling the Ice Maker” section.
Push the ice maker into position so that the ice maker drain
3.
tube is positioned over the standpipe.
SIDE VIEW
Understanding Sounds You May Hear
Your new ice maker may make sounds that are not familiar to
you. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard
surfaces like the floor, walls and cabinets can make the sounds
seem louder than they actually are. The following describes the
kinds of sounds that might be new to you and what may be
making them.
■ You will hear a buzzing sound when the water valve opens to
fill the water reservoir for each cycle.
■ Rattling noises may come from the flow of the refrigerant or
the water line. Items stored on top of the ice maker can also
make noises.
■ The high efficiency compressor may make a pulsating or high
pitched sound.
■ Water running over the evaporator plate may make a
splashing sound.
■ Water run ning from the evapor ator plate to th e water r eservoir
may make a splashing sound.
■ As each cycle ends, you may hear a gu rgling sound due to
the refrigerant flowing in your ice maker.
■ You may hear air being forced over the condenser by the
condenser fan.
■ During the harvest cycle, you may hear a “thud” when the ice
sheet slides from the evaporator onto the cutter grid.
■ When you first start the ice maker, you may hear water
running continuously. The ice maker is programmed to run a
rinse cycle before it begins to make ice.
7/8
1
"
20" (50.80 cm)
1. Floor Line
2. 1 in. (2.54 cm) Air Gap
3. Standpipe
4. Center of drain should be 20 in. (50.80 cm)
from front of door.
If it is required by your local sanitation code, seal the cabinet
4.
to the floor with an approved caulking compound after all
water and electrical con nections have been made.
1" (2.5 cm)
1/2
1
" (3.8 cm)
Drain pump system (on some models)
Connect the dr ain pump hos e (pr ov ide d with the pr od uct) to yo ur
drain in accordance with all state and local codes and
ordinances.
USING YOUR
ICE MAKER
Understanding How Your Ice Maker
Wo r ks
When you first start your ice maker, the water pan will fill and the
system will rinse itself before starting to make ice. The rinsing
process takes about five minutes.
Under normal operating conditi ons, the ice maker will cycle at
preset temperatures. The ice level sensor located in the ice
storage bin will monitor the ice levels.
IMPORTANT:
■ If the water supply to the ice maker is turned off, be sure to
set the ice maker control to OFF.
■ The ice maker is designed to make clear ice from the majority
of water sources on a daily basis. If your results are
unsatisfactory, your water may need to be filtered or treated.
7
The Ice Making Process
1. Water is constantly circulated over a freezing plate. As the
water freezes into ice, the minerals in the water are rejected.
This produces a clear sheet of ice with a low mineral content.
2. When the desired thickness is reached, the ice sheet is
released and slides onto a cutter grid. The grid divides the
sheet into individual cubes.
3. The water containing the rejected minerals is drained after
each freezing cycle.
4. Fresh water enters the machine for the next ice making cycle.
5. Cubes fall into the storage bin. When the bin is full, the ice
maker shuts off automatically and restar ts when more ice is
needed. The ice bin is not refrigerated and some melting will
occur. The amount of melting varies with room temperature.
NOTE: As the room and water temperatures vary, so will the
amount of ice produced and stored. This means that higher
operating temperatures result in reduced ice production.
Setting the Controls
1. To start the normal ice making cycle, select ON.
2. To stop ice maker operation, select OFF.
CARING FOR YOUR ICE
MAKER
Periodically inspect an d clean the ice maker to keep it operating
at peak efficiency and to prevent premature failure of system
components.
Both the ice making system and the air cooled condenser need
to be cleaned regularly.
The minerals rejected from the circulating water during the
freezing cycle will eventually form a hard scaly deposit in the
water system which prevents a rapid release of the ice from the
freezing plate.
Clean the ice and water sys tem periodically to remove mineral
scale buildup. Frequency of cleaning depends on water
hardness. With hard water (15 to 20 grains/gal. [4 to 5 grains/
liter]), cleaning may be required as frequently as every 6 months.
Cleaning Exterior Surfaces
Wash the exterior enamel surfaces and gaskets with warm water
and mild soap or detergent. Wipe and dry. Regular use of a good
household appliance cleaner and wax will help protect the finish.
Do not use abrasive cleaners on enamel surfaces as they may
scratch the finish.
For products with a stainless steel exterior, use a clean sponge or
soft cloth and a mild detergent in warm water. Do not use
abrasive or harsh cleaners.
Cleaning the Ice Maker System
NOTE: Use one 16 oz (473 mL) bottle of NU-CALGON* Nickel
Safe Ice Machine Cleaner. To order, call 1-800-442-9991 and
ask for Part Number 8171307.
1. Push the selector switch to OFF.
2. Wait 5 to 10 minutes for the ice to fall into the storage bin.
Remove all ice from the storage bin.
3. Unscrew the drain cap from the bottom of the water pan
located inside the storage bin as shown. Allow the water to
drain completely.
4. Replace the drain cap securely on the water pan. If the drain
cap is loose, water will empty from the water pan and you will
have either thin ice or no ice.
5. Read and fol low all handlin g in forma tion on th e c lea ner b ottle
before completing the steps below. Use one 16 oz (473 mL)
bottle of NU-CALGON* Nickel Safe Ice Machine Cleaner.
6. Pour one bottle of solution into the water pan. Fill the bottle
twice with tap water and pour it into the water pan.
NOTE: The CLEAN setting is used whenever solutions are
circulated through the ice maker for cleaning. Only the water
pump and compressor operate at this setting. See the “Cleaning
the Ice Maker System” section.
8
1
2
1. Water Pan
2. Drain Cap
Loading...