KitchenAid KUDS40FVPA3, KUDS50SVWH3, KUDS50SVWH4, KUDS50SVSS4, KUDS50SVWH0 Installation Guide

KitchenAid ®

iNSTALLATiON iNSTRUCTiONS

UNDERCOUNTER DISHWASHER
iNSTRUCTiONS D'INSTALLATION

LAVE-VAISSELLESOUS PLAN DE TRAVAIL

Table of Contents ................................... 2

Table des matieres .................................. 27

W10056407A

Table of Confenfs

Dishwasher Safety ................................. 2

Installation Requirements ........................... 3

Tools and Parts ................................... 3

Location Requirements ............................ 4

Drain Requirements ............................... 6

Water Supply Requirements ........................ 6

Electrical Requirements ............................ 6

Installation instructions ............................. 7

Prepare Cabinet Opening--Existing Utilities ........... 7

Prepare Cabinet Opening--New Utilities .............. 7

Prepare and Route Water Line ...................... 8

install Drain Hose ................................ 9

Install Moisture Barrier (on some models) ........... 10

Prepare Dishwasher ............................. 11

Make Power Supply Cord Connection ............... 12

Determine Cabinet Opening ....................... 13

installation instructions (cont.}

Install the Door Handle (on some models) ........... 14

Custom Panel Dimensions ........................ 14

Install Custom Panel - Option 1 .................... 15

Install Custom Panel - Option 2 .................... 16

Choose Attachment Option ........................ 17

Move Dishwasher Into Cabinet Opening ............. 18

Connect to Water Supply ......................... 20

Connect to Drain ................................ 21

Make Direct Wire Electrical Connection .............. 21

Secure Dishwasher in Cabinet Opening ............. 23

Complete installation ............................. 24

Check Operation ................................. 25

If Dishwasher Does Not Operate ................... 25

Additional Tips .................................. 25

DISHWASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:

You can be killed or seriously injured if you don't immediately
follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

You Need to:

, Slowly open dishwasher door while someone grasps the

rear of the dishwasher. Remove shipping materials, drain
hose and lower rack. Close dishwasher door until latched.

, Observe all governing codes and ordinances.
, Install this dishwasher as specified in these instructions.
, Installation should be performed by a qualified service

Tip Over Hazard

Do not use dishwasher until completely installed.
Do not push down on open door.

Doing so can result in serious injury or cuts.

technician. The dishwasher must be installed to meet all

electrical and plumbing national and local codes and
ordinances.

2

iNSTALLATiON REQUIREMENTS

Tools and Parts

Gather the recommended tools and parts before starting
installation. Read and follow the instructions provided with
any tools listed here.

All Installations

Tools needed:

_,. /_ z_2 Flat-bade
ruers I screwdriver

5/16" and 1/4" _ ' UL listed or CSA
nut drivers or _f approved twist-on ff

hex sockets _ wire connectors* v

10" adjustable wrench 5/8" open -end

that opens to wrench

1.18" (2.9 cm) _.
If installing custom front panels, _y

Torx T15 screwdriver _'

-Must be the proper size to connect your household wiring
to 16-gauge wiring in dishwasher

Other useful items you may need:

F ash ight _ Bathtowe _

Other parts you may also need:

1i " 2"

/2-

1!38:1_5:0em) I Masking or

i Screw-type

[damps_3max)J

NOTE: Parts available for purchase Jn plumbing supply stores.

Check local codes. Check existing electrical supply. See

"Electrical Requirements" section. It is recommended that

electrical connections be made by a licensed electrical installer.

In addition, for first=time installations

Tools needed:

Iwith 1/2 513/4 7//,
_and11!2 h01e_]

saw bits ...................

Parts needed:

C0ppei tubing (3/8!'
OiD. suggested) o[

flexible braided

W_e

Additional parts supplied with top=venting models only:

see "Electrical Requirements" Section

Fo[ Direct wire: For Power supply

i use UL listed or Card: useUL

CSA approved listed power

i st[ain;re!ief to Supply cord kit
i fit7/8 (2.2cm) marked for use

hoe with dishWasher

Parts supplied:

@ sCrows

r Green

Make sure all these parts are included in the literature package.

Parts needed:

90° ElboW fitting with 3/8_, Tefl0n_ tape Or pipe

N.RT, external threads (the joint Compou[
other end mUSt fit yOUr Water

Supply line)

4 #10 x 1/2" wood screws (if installing custom front panels)

® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.
t® TORX is a registered trademark of Acument Intellectual Properties, LLC.

Torx.so 10x , ,hex a scewsi

Additional parts supplied with certain models only:

I Bottom Sound pad (located I Moisture bairier tape
[in lower rack) [ l

Make sure all these parts are included in the literature package.
If parts are not included, call 1-800-422-1230.

Location Requirements

Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where

they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must

provide clearance between motor and flooring. Motor
should not touch the floor.

Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher

against freezing. Damage from freezing is not covered by
the warranty.

A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part Number 4396277) is
available from your dealer for installing underneath the
countertop, but is not required. Call 1=800=422=1230 to

order.

Check location where dishwasher will be installed. The

location must provide:

easy access to water, electricity and drain.
convenient access for loading and unloading dishes.

Corner locations require a 2" (5.1 cm) minimum
clearance between the side of the dishwasher door

and the wall or cabinet.

square opening for proper operation and appearance.
cabinet front perpendicular to floor.

level floor. (If floor at front of opening is not level with
floor at rear of opening, shims may be needed to level

dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions
and ensure dishwasher is level if the floor in the

dishwasher opening is uneven (example: Flooring
extends only partway into opening).

NOTE: To avoid shifting during dishwasher operation,

shims must be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it

winterized by authorized service personnel.

Make sure pipes, wires and drain hose are within the

shaded area shown in the "Product and Cabinet
Opening Dimensions" section.

4

Product and Cabinet Opening Dimensions

J

*Insulation may be compressed

(not used on al models:_

NOTE: Shaded area of cabinet walls show where
utility connections may be installed.

*Measured from the lowest point on the

underside of countertop. May be reduced to

33 7/8" (86 cm) by removing wheels from

dishwasher.

**Minimum, measured from narrowest point of /

opening.

Check that all surfaces have no protrusions
that would prohibit dishwasher installation.

cco

_0. /

Drain Requirements

Eiecfrical Requiremenfs

, A new drain hose is supplied with your dishwasher.

if this is not long enough, use a new drain hose with a
maximum length of 12' (3.7 m) (Part Number 3385556)

that meets all current AHAM/IAPMO test standards, is

resistant to heat and detergent, and fits the 1" (2.5 cm)
drain connector of the dishwasher.

* Make sure to connect drain hose to waste tee or disposer

inlet above drain trap in house plumbing and 20"
(50.8 cm) minimum above the floor. It is recommended

that the drain hose either be looped up and securely

fastened to the underside of the counter, or be connected

to an air gap.

Be sure that the electrical connection and wire size are

adequate and in conformance with the National Electrical
Code, ANSI/NFPA 70 - latest edition and all local codes and

ordinances.
A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park
Quincy, MA 02269

You must have:

120-volt, 60 Hz, AC-only, 15 or 20 amp, fused electrical
supply.

* copper wire only.

We recommend:

* a time-delay fuse or circuit breaker.
* a separate circuit.

if connecting dishwasher
with a power supply cord:

, Use UL listed power supply cord kit (Part Number

4317824) marked for use with dishwasher.
Power supply cord must plug into

a grounded 3 prong outlet, located in

the cabinet next to the dishwasher

opening. Outlet must meet all local

codes and ordinances.

Make sure to use an air gap if the drain hose is connected

to house plumbing lower than 20" (50.8 cm) above

subfloor or floor.
Use 1/2" minimum I.D. drain line fittings.

If required, the air gap should be installed in accordance
with the air gap installation instructions. When you are
connecting the air gap a rubber hose (not provided) will

be needed to connect to the waste tee or disposer inlet.

Wafer Supply Requiremenfs

* A hot water line with 20-120 psi (138-862 kPa) water

pressure can be verified by a licensed plumber.

* 120°F (49°C) water at dishwasher.
* 3/8" O.D. copper tubing with compression fitting or

flexible braided water supply line (Part Number

4396897RP)

NOTE: 1/2" minimum plastic tubing is not recommended.

* A 90 ° elbow with 3/8" N.RT. external pipe threads on one

end.

* Do not solder within 6" (15.2 cm) from water inlet valve.

if connecting dishwasher with direct wiring:

* Use flexible, armored

or nonmetallic
sheathed, copper wire

with grounding wire
that meets the wiring requirements for your home and

local codes and ordinances.

* Use a UL listed or CSA approved strain relief.

iNSTALLATiON iNSTRUCTiONS

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

DisconneCt electrical power at the fuse box or Circuit !

breaker box before installing dishwash

Prepare Cabinet OpeningmExisting
Utilities

If the water line and the cable extend to the locations
shown, proceed to the "Install Drain Hose" section. If they

do not reach far enough, follow the instructions in the
"Prepare Cabinet Opening--New Utilities" section.

Prepare Cabinet OpeningmNew
Utilities

Yes _FoIIow instructions inthe "Prepare cabinet

Opening_Existing Utilities', section!

No _FoIIOW inStruCtions in the ,Prepare Cabinet

Opening_New uti!!ties Sect!0nl

Existing Utility hookups g t ity hookups

Water line

Prepare and route the electrical supply

What type of electrical
connection will you use? L

c:_ _ P0wer Supply Cord:

Option A, Power Supply Cord:

NOTE: A grounded 3 prong outlet is required inside a

cabinet next to the dishwasher cabinet opening.

Follow Option A inStructions

Direct Wire:
FOllow option B instructions

Drill a 1 1/2" (3.8 cm) hole in cabinet side or rear.
See product and cabinet opening dimensions.

7

Woodcabinet:Sandholeuntilsmooth.
Metalcabinet:Coverholewithgrommetincludedwith

powersupplycordkit.

OptionB, Direct Wire:

Helpful "lip: Wiring the dishwasher will be easier if you

route the cable into the cabinet opening from the right side.

Drill a 3/4" (1.9 cm) hole in right-hand cabinet side or rear.
See product and cabinet opening dimensions.

Route cable from power supply through cabinet hole (cable

must extend to the right front side of cabinet opening).
Tape cable to the floor in area shown. This will prohibit
cable from moving when dishwasher is moved into
cabinet opening.

Prepare and Roule Waler Line

Helpful Tip: Routing the water line through the left side
of cabinet opening will make water connection easier.

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet (not provided).

8

Drill a 1/2" (1.3 cm) hole in the cabinet side or rear.

Measure overall length of copper tubing or flexible
braided water supply line. Attach to the hot water line
using a connection configuration that is in compliance

with local codes and ordinances. The water line to the

dishwasher should have a manual shutoff valve.

Slowlyroutewatersupplylinethroughholeincabinet.
(Ifusingcoppertubing,itwill bendandkinkeasily,sobe

gentle.)Itshouldbefarenoughintothecabinetopening

toconnectittothedishwasherinletonthefrontleft

sideofthedishwasher.

Slowlyturnwatershutoffvalveto "ON"position.Flush
waterintoashallowpanuntilcleartogetridofparticles

thatcouldclogtheinletvalve.Turnshutoffvalveto

"OFF"position.

Route drain hose as shown through hole in cabinet to the
front center of opening where drain connection will be
made. Tape drain hose to the floor in area shown. This will
prohibit it from moving when dishwasher is moved into
cabinet opening.

IMPORTANT: The drain hose connection of the disposer or
a waste tee must be made before the drain trap and at

least 20" (50.8 cm) above the floor where the dishwasher

will be installed.

Helpful Tip: To reduce vibration of the hose, keep the hose
away from the floor.

Option A, Waste disposer - no air gap

iiii_if_i{_i{_i{_i_iiiiii_iii_iii_iiiiii_i_iiiiiii_i_ii_iii_i_i_ii_i_iiiiiii_iiiiiii_iiiiii_iiiiiiiB_);_;ii_);_;ii_ii_i_ii_i_ii_i_ii_i_ii_i_);i_;i_;;ii;i_;ii_);i_;i;i_ii_i_ii_i_ii_i_ii_i_ii_i;_i;i_;;ii;i_;;i;iiIi_;i_;;i_);_;ii_);_ii¸i_;i_;i_i;;ii;i_;ii_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_i{_ii)y

InsfallDrain Hose

IMPORTANT: Always use a new drain hose. Check local
codes to determine if an air gap is required.

If needed, drill a 1 1/2" (3.8 cm) diameter hole in cabinet
wall or side of the opening closest to the sink.

i iii

Drai

1. Using a hammer and screwdriver,
knock plug into disposer.

2. Use needle nose pliers to remove
plug.

3. Attach drain hose to disposer inlet
with large silver drain hose clamp

(provided). Use pliers to squeeze

clamp open and move into position.

Option B, No waste disposer - no air gap

1.Connect black end of of drain hose to
waste tee and cut if needed.

(Do not cut ribbed section.)

2. Attach black end of drain hose to waste
tee with a large silver drain hose clamp

(provided). Use pliers to squeeze clamp

open and move into position. If the drain

hose was cut use a 1 1/2" to 2" (3.8 to

5 cm) screw-type clamp (not provided).

Option C, Waste disposer - with air gap

Option D, No waste disposer - with air gap

Connect black end of drain hose to air
gap and cut if needed. (Do not cut

ribbed section.)

2.

Attach drain hose to air gap with large
silver drain hose clamp (provided).

Use pliers to squeeze clamp open and

move into position. If the drain hose
was cut, use a 1 1/2" to 2"(3.8 to 5 cm)
screw-type clamp (not provided).

3.

Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from waste tee to air gap.

Drain trap

1. Using a hammer and screwdriver,
knock plug into disposer.

2. Use needle nose pliers to remove
plug.

3. Connect black end of drain hose to air
gap and cut if needed. (Do not cut

ribbed section.)

4.

Attach drain hose to air gap with large
silver drain hose clamp (provided).

Use pliers to squeeze clamp open and
move into position. If the drain hose
was cut, use a 1 1/2" to 2"(3.8 to
5 cm) screw-type clamp (not
provided).

Install Moisture Barrier

(on some models)

I

Moisture

barrier

1. Make sure the area under the cabinet is clean and dry
for installation of the moisture barrier.

2. Remove the backing of the moisture barrier and apply
to underside of the countertop along the front edge of

the counter.

I

10

5.

Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from air gap to disposer inlet.

Prepare Dishwasher

Tip Over Hazard

Do not use dishwasher until completely installed.
Do not push down on open door.

Doing so can result in serious injury or cuts.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Apply Teflon ® tape or pipe joint compound to 90 ° elbow
fitting (not provided). Wrap tape around coarse threads

two to four times to prohibit leaks.

Helpful Tip: Place cardboard under dishwasher until installed
in cabinet opemng to avoid damaging floor covering. Do not

use door panel as a work table without first covering with a

towel to avoid scratching the door panel.

Using two or more people, grasp sides of dishwasher door

frame and place dishwasher on its back.

Using a 1/4" hex head socket, nut driver or Phillips
screwdriver, remove two screws attaching access panel
and lower panel to dishwasher. Do not remove tech
sheet from access panel.

Connect 90° elbow fitting to water inlet valve. Using a
wrench, tighten elbow until snug, and be sure that it
faces to the rear.

Using a 1/4" hex head socket, nut driver or Phillips
screwdriver, remove terminal box cover. Retain for

later use.

11

InstallaULlistedorCSAapprovedstrainrelief.Makesure
screwheadsarefacingtotheleftwhentighteningconduit
nut.Strainreliefisprovidedwiththepowersupplycordkit.

connection will you use? [ __

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord.
Failure to follow these instructions can result in

death, fire, or electrical shock.

Power Supply Cord:

Follow Option A instructions

.................................................................................

Make Power Supply Cord Connection

Option A, Power Supply Cord:

-- _ _--

III I tt %::,#///!_ < _ar--Wl re sh

Remove the green grounding screw and place through
the ring terminal of the green ground wire. Reattach and
tighten the green screw.

)

Route cord so that it does not touch dishwasher motor

to lower part of dishwasher tub. Pull cord through strain

relief in terminal bow. Take notice when installing or
removing the dishwasher in order to reduce the chance

of damaging the power supply cord.

Select UL listed or CSA approved twist-on wire connectors

(included with power supply cord kit) rated to connect

your household wiring to 16-gauge dishwasher wiring.

12

NOTE: Twist on wire connector. Gently tug on wires to

be sure both are secured.

Connect wires black to black and white to white, using

UL listed or CSA approved twist-on wire connectors

(included with power supply cord kit).

Ifneeded,seewebsiteforanimatedrepresentationof
thisstep.Visitwww.kitchenaid.comunderFAQtab.

Defermine Cabinet Opening

Measure height of cabinet opening from underside of
countertop to floor where dishwasher will be installed
(you will need to measure the lowest point on the
underside of the countertop and the highest point on the
floor). Refer to "Dishwasher Height Adjustment Chart"
for wheel position and the number of turns needed.

Cabinet I Wheel Number of turns

Opening height position on front leg

33 7/8'i (86.0 Cm) I remove I the way up

Tightenstrainreliefscrewstosecurecord.

34 1/4" (87cm) . 2 . 5

34 1/2" (87:6 cm) 3 0

NOTE: If the minimum cabinet opening height is less than
34"(86.4 cm), the rear wheels can be removed for

additional clearance. This will allow the dishwasher to fit
into a 33 7/8" (86 cm) high cabinet opening, but the

dishwasher will be more difficult to move. (Measurements
are approximate. Wheels and legs are preset at the

factory for 34 1/2" [87.6 cm].)

2

Adjust wheels and legs ......

|

m

J

)

!

Placewiresinsideterminalbox.Inserttabsonleftside
ofcover.Makesurewiresaretuckedinsidebox.Close

coverensuringwiresarenotpinched.Use1/4"nut
driverandpreviouslyremovedscrewtosecurecover.

NOTE:Donotplugintooutletuntilinstructedtodoso.

Turn both leveler legs to the same height. Put wheels in
the required position determined from "Dishwasher

Height Adjustment Chart."

13

Built-upfloorsKitchenfloorheightishigherthan

cabinetopening.)Example:Kitchenfloortiledoesnot

extendintocabinetopening.Addshimsasneededinthe
areashowntobringthedishwasherupto34"(86.4cm)
belowthecountertop.

NOTE:Shimsmustbesecurelyattachedtofloortoavoid
movementwhenthedishwasherisinuse.

IMPORTANT:Youneedtoknowwhatcontrolpanelison
yourdishwasherbeforeyouorderyourcustomdoor

panel.

Dishwashers with control panel on
top custom panel dimensions

23 1/2" /" _ -_Z.30 3/16" (76.7 cm)

7 cm'

*This dimension is for 4" (10.2 cm) toe kick. Ifthe

installation needs a higher toe kick, adjust the height
of the wood panel accordingly. Not recommended for

toe kicks greater than 6" (15.2 cm).

Follow directions under Option 1 of "Install custom
panel" section.

Mountingstud

Handle

Setscrew

(inbottom

of )

Allen

IMPORTANT:Donotscratchthefrontpanelduringthis
procedure.

Removethedoorhandleandhardwarebagcontaining

thesetscrewsandAllenwrenchfromthecardboardbox.

Setscrewsarealreadyinstalledinthehandle.Place
handleonmountingstudswiththesetscrewsfacing
down.Pushthedoorhandletightlyagainstthedoor.

InserttheshortendoftheAllenwrenchintothe
setscrews.Tightenthesetscrews1/4turnpastsnug.

RetainAllenwrenchwithInstallationInstructions.

Dishwashers with control panel on
front custom panel dimensions

(19.1 mm)

*This dimension is for 4" (10.2 cm) toe kick. If the

installation needs a higher toe kick, adjust the height
of the wood panel accordingly. Not recommended for
toe kicks greater than 6" (15.2 cm).

Follow directions in Option 2 of "Install custom panel"

section.

(3.2 mm)

mm)

14

InstallCustom Panel - Option ]

(Models KUDG40FVPA, KUDG50FVPA, KUDE60FVPA,

and KUDE70FVPA}

NOTE: The handle for the custom panel is not included.

IMPORTANT: If the handle is attached from the back of
the custom panel, the screw holes should be countersunk

for the screws heads to be flush with the panel. If the

handle is attached to the front of the custom panel, the
screw lengths cannot exceed the panel thickness. For
more information on KitchenAid custom handle selection,

refer to the KitchenAid Catalog, visit
www.kitchenaid.com, or call 1-8OO-422-1230.

NOTE: A customer-supplied full front panel must weigh

no more than 16 Ibs (7.3 kg) and must be made to
specific dimensions. It is recommended that a
cabinetmaker cut the custom panel because of the

precise dimensions needed.

NOTE: All mounting hardware supplied is for a 3/4"

(19.1 mm) thick wood panel. If a thinner wood panel, or

materials other than wood are used, it is the consumer's

responsibility to obtain the proper length screws and
adjust the pilot holes accordingly.

IMPORTANT: Use a moisture resistant sealer on both
sides and all edges of the panel to avoid damage from

humidity.

Dishwashers with control panel on

top custom panel dimensions

....J

3 screws

per side

outer F

Gently set outer panel aside. Lay the customer-supplied
custom panel face down on a covered, non-scratching

surface.

9 29/32"

(25.2 cm)

1 ICustom panel installation

-:J Dishwashers with control |

panel on the top ....

23 1/2" _"'_"30 3/16" (76.7 cm)

7 cm'

*This dimension is for 4" (10.2 cm) toe kick. If the

installation needs a higher toe kick, adjust the height
of the wood panel accordingly. Not recommended for

toe kicks greater than 6" (15.2 cm).

With a TORX _)screwdriver, remove three screws from both
sides, as shown; hold the outer panel up while removing

the screws. Save screws for reinstallation.

p edge

Measure 9 29/32" (25.2 cm) from top edge and mark a line
on the back of customer-supplied custom panel. Position the
outer panel on the back of the customer-supplied custom
panel as shown, so that the top holes in the outer panel are
on the line, and both panels are centered side to side.

holes

Mark all four hole locations; remove outer panel. Drill 3/32"
pilot holes 1/2" (13 mm) deep in customer-supplied custom
panel. Place the outer panel on the back of the customer-

supplied custom panel; align holes.

15

Customer-supplied

panel

edges

)rill through
these holes

top

Attachouterpaneltobackofcustomer-suppliedcustom

panelwiththefour#10-16x3/8"hexheadscrewssupplied

intheliteraturepackage.Attachthehandle.Thehandle
shouldbecenteredonthefrontofthecustomer-supplied
custompanelintheareashown.

IMPORTANT:Screwheadsmustbeflushwithbackof
customer-suppliedcustompanel.

i

R edges
3 screws

each side Customer-supplied

panel

J

Attach the panel assembly to the door by reinstalling the
three screws on each side; do not tighten completely. This

reinstallation of the three screws will hold the panel
assembly in place on the door frame.

Install the two #8-18 x 1 3/8" screws from

the literature package in the top corners of the inner

panel. Tighten the six side screws reinstalled in Step 6.

Install Custom Panel - Option 2

(Models KUDCO21V and KUDS2OIV)

All models require an accessory option to attach custom

panels. Kit Number 8171555 (black), 8171556 (white) or
8171557 (biscuit) are available. To order, call customer

service at 1-8OO-444-1230.

NOTE: A custom full front panel must weigh no more

than 14 Ibs (6.3 kg) and must be made to specific

dimensions. It is recommended that a cabinetmaker cut

the custom panel because of the precise dimensions

needed.

IMPORTANT: Use a moisture resistant sealer on both

sides and all edges of the panel to avoid damage from

humidity.
NOTE: These dimensions are for frameless custom panel

models with a 4" (10.2 cm) console only.

Custo m pa neI insta IIation -

1J Dishwashers with control 1

panel on the front | ...................

/

23 3/8" /'_1"_,25 29/32" (65.8 cm)

top

edges

Drill through

these holes

Customer-supplied

panel

Align the top edge of the customer-supplied custom

panel with the top of the console.

Drill two 3/32" pilot holes 1/2" (13 mm) deep, into the
customer-supplied custom panel, through the holes in the

top corners on the inner panel, as shown.

16

i,,_

(65.8 cm) _____.._

mm)

*This dimension is for 4" (10.2 cm) toe kick. If the

installation needs a higher toe kick, adjust the height
of the wood panel accordingly. Not recommended for
toe kicks greater than 6" (15.2 cm).

With a TORX _screwdriver, remove three screws from

both sides, as shown; hold the outer panel up while
removing the screws. Save screws for reinstallation.

(3.2 mm)

mm)