Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
can be killed or seriously injured if you don't
You
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can
happen if the instructions are not followed.
3
Before Using Your Dishwasher
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
■
Install where dishwasher is protected from the elements.
Protect against freezing to avoid possible rupture of fill valve.
Such ruptures are not covered by the warranty. See “Storing”
in the “Dishwasher Care” section for winter storage
information.
■
Install and level dishwasher on a floor that will hold the
weight, and in an area suitable for its size and use.
■
Remove all shipping plugs from hoses and connectors (such
as the cap on the drain outlet) before installing. See
Installation Instructions for complete information.
4
PARTS AND FEATURES
1.
Upper spray arm
2.
Top r ac k
3.
Model and serial number label
4.
Water inlet opening [in tub wall]
5.
4-way HYDRO SWEEP™
spray arm
Control Panel
6.
Bottom rack
7.
Detergent dispenser
8.
Vent system
9.
Middle spray arm
10.
Silverware basket
11.
Overfill protection float
12.
Heating element
13.
Rinse aid dispenser
14.
Control panel
Cancel
5
START-UP GUIDE
Before using your dishwasher, remove all packaging materials.
Read this entire Use and Care Guide. You will find important
safety information and useful operating tips.
7.
Push door firmly closed. The door latches automatically.
Using Your New Dishwasher
1.
Scrape large food soil and hard items (toothpicks or bones)
from dishes.
2.
Properly load the dishwasher. (See “Dishwasher Loading.”)
Make sure nothing prevents the spray arm(s) from spinning
freely.
3.
Add detergent and check the rinse aid dispenser. Add rinse
aid if needed. (See “Dishwasher Use.”)
4.
Run hot water at the sink nearest your dishwasher until the
water is hot. (See “Dishwasher Efficiency Tips.”) Turn off
water.
5.
Press the desired cycle and option selections. (See
“Dishwasher Use.”)
6.
Press START. Or press START to repeat the same cycle and
options as the previous cycle.
The lights on the control panel will turn off and the cycle will
begin. If the door is opened during the cycle, the cycle and option
lights will turn back on.
NOTE:
If the dishwasher is not started before closing the
door, the cycle and options will revert to the last cycle and
options completed.
DISHWASHER
LOADING
Loading Suggestions
■
Remove leftover food, bones, toothpicks and other hard
items from the dishes. To conserve water, energy and save
time it is not necessary to rinse dishes before putting them in
the dishwasher. The wash module removes food particles
from the water. The module contains a chopping device
which will reduce the size of food items.
NOTE:
If hard items such as fruit seeds, nuts, and egg shells
enter the wash module, you might hear chopping, grinding,
crunching, or buzzing sounds. These sounds are normal
when hard items enter the module. Do not let metallic items
(such as pot handle screws) get into the wash module.
Damage can occur.
■
It is important for the water spray to reach all soiled surfaces.
■
Load dishes so they are not stacked or overlapping if
possible. For best drying, water must be able to drain from all
surfaces.
■
Load heavy pots and pans carefully. Heavy items can dent
the stainless steel interior of the door if they are dropped or
bumped.
■
Make sure pot lids and handles, pizza pans, cookie sheets,
etc., do not interfere with the spray arm rotation.
■
Conserve water, energy and save time over hand rinsing by
running a rinse cycle to keep dishes moist if you do not plan
to wash them soon. Foods such as eggs, rice, pasta,
spinach, and cooked cereals may be hard to remove if they
are left to dry over a period of time.
Quiet operating tips
To avoid thumping/clattering noises during operation:
■
Make sure lightweight load items are secured in the racks.
■
Make sure pot lids and handles, pizza pans, cookie sheets,
etc., do not touch interior walls or interfere with the rotation of
the spray arm.
■
Load dishes so they do not touch one another.
NOTE:
For built-in models, keep sink drain plugs closed during
dishwasher operation to prevent noise transfer through drains.
The top rack is designed for cups, glasses, and smaller items.
Loading Top Rack
Many items, up to 9 in. (22 cm), fit in the top rack. (See
recommended loading patterns shown.)
6
NOTE:
The features on your dishwasher rack may vary from the
drawings shown.
10 place setting
12 place setting
■
Place items so open ends face down for cleaning and
draining.
■
Load glasses and cups in top rack only. The bottom rack is
not designed for glasses and cups. Damage can occur.
■
Place cups and glasses in the rows between tines. Placing
them over the tines can lead to breakage and water spots.
NOTE:
The features on your dishwasher rack may vary from the
drawings shown.
10 place setting
12 place setting
■
Do not load glasses, cups, or plastic items in the bottom
rack. Load small items in the bottom rack only if they are
secured in place.
■
Load plates, soup bowls, etc., between tines.
■
Overlap the edges of plates for large loads.
■
Load soup, cereal, and serving bowls in the rack in a variety
of ways depending upon their size and shape. Load bowls
securely between the rows of tines. Do not nest bowls
because the spray will not reach all surfaces.
Cup and glass load
■
China, crystal, and other delicate items must not touch each
other during dishwasher operation. Damage may occur.
■
Load plastic items in the top rack only. Only plastic items
marked “dishwasher safe” are recommended.
■
Load plastic items so the force of the spray does not move
them during the cycle.
■
To avoid chipping, do not let stemware touch other items.
■
Small bowls, pans, and other utensils can be placed in the
top rack. Load bowls in the center section for best stability.
Loading Bottom Rack
The bottom rack is designed for plates, pans, casseroles, and
utensils. Many items, up to 13 in. (33 cm) tall, fit in the bottom
rack. (See recommended loading patterns shown.)
Utensil load
7
■
1
2
3
4
Load cookie sheets, cake pans, and other large items at the
sides and back. Loading such items in front can keep the
water spray from reaching the detergent dispenser.
Mixed load
■
Secure heavily soiled cookware face down in the rack.
■
Make sure pot handles and other items do not stop rotation
of the spray arm(s). The spray arm(s) must move freely.
■
Do not load items between the bottom rack and the side of
the dishwasher tub because they might block the water inlet
opening.
Loading Silverware Basket
Load the silverware basket while it is in the bottom rack or take
the basket out for loading on a counter or table.
NOTE:
Unload or remove the basket before unloading the racks
to avoid spilling water droplets on the silverware.
DISHWASHER USE
Detergent Dispenser
The detergent dispenser has 2 sections. The smaller Pre-Wash
section empties detergent into the dishwasher when you close
the door.
1. Cover latch
2. Main Wash section
3. Pre-Wash section
4. Cover
The larger Main Wash section automatically empties detergent
into the dishwasher during the wash. (See the “Cycle Selection
Charts.”)
■
Use automatic dishwashing detergent only. Other detergents
can produce excessive suds that can overflow out of the
dishwasher and reduce washing performance.
■
Add detergent just before starting a cycle.
■
Store tightly closed detergent in a cool, dry place. Fresh
automatic dishwasher detergent results in better cleaning.
NOTE:
Do not use detergent with a rinse cycle.
Filling the dispenser
1.
If the dispenser cover is closed, open the cover by pushing
the cover latch.
Mix items in each section of the basket with some pointing up
and some down to avoid nesting. Spray cannot reach nested
items.
2.
Fill the Main Wash section with detergent. See “How Much
Detergent to Use.”
3.
Fill the Pre-Wash section, if needed.
4.
Close the dispenser cover.
IMPORTANT:
pointing down.
NOTES:
■
Do not load silver or silver-plated silverware with stainless
steel. These metals can be damaged by contact with each
other during washing.
■
Some foods (such as salt, vinegar, milk products, fruit juices,
etc.) can pit or corrode silverware. Run a rinse cycle if you do
not have a full load to wash immediately.
Always load sharp items (knives, skewers, etc.)
It is normal for the cover to open partially when dispensing
detergent.
NOTE:
Use both sections for cycles with 2 washes. Use only the
main wash section for cycles with 1 wash. See the “Cycle
Selection Charts” for more details.
8
How much detergent to use
1
2
3
■
The amount of detergent to use depends on the hardness of
your water and the type of detergent. If you use too little,
dishes won’t be clean. If you use too much in soft water,
glassware will etch.
■
Water hardness can change over a period of time. Find out
your water’s hardness by asking your local water department,
water softener company, or county extension agent.
■
You can order a water hardness test strip. In the U.S.A., call
the Customer Interaction Center and ask for Part Number
4171690.
■
Different brands of dishwasher detergent have different
amounts of phosphorus for softening water. If you have hard
water and use a detergent with a phosphorous content of
less than 8.7%, you might need to use more detergent, or use
a detergent with a phosphorous content higher than 8.7%.
Water HardnessAmount of Detergent
Rinse Aid Dispenser
Rinse aids prevent water from forming droplets that can dry as
spots or streaks. They also improve drying by allowing water to
drain off of the dishes during the final rinse by releasing a small
amount of the rinse aid into the rinse water. Your dishwasher is
designed to use a liquid rinse aid. Do not use a solid or bar-type.
Filling the dispenser
The rinse aid dispenser holds 4.8 oz (145 mL) of rinse aid. Under
normal conditions, this will last for about three months. You do
not have to wait until the dispenser is empty to refill it. Try to keep
it full, but be careful not to overfill it.
1.
Make sure the dishwasher door is fully open.
2.
Open the dispenser by pushing the cover latch.
Soft to Medium
Hard Water
0 to 6 grains per
gallon
Medium to Hard
Water
7 to 12 grains per
gallon
Very Hard Water
13 grains per gallon
and above
NOTE:
It might be
necessary to use the
Heavy cycle, or a
normal cycle with
Hi-Temp Wash, for
best wash
performance with
very hard water.
For normally soiled loads
■
Partially fill the Main Wash
section (5 tsp or 25 g)
■
Fill the Pre-Wash section
(4 tsp or 20 g)
NOTE:
Add only 2 tsp or 10 g of
detergent to the Pre-Wash section if
dishes are pre-rinsed or the water is
very soft (0 to 2 grains per gallon).
For heavily soiled loads
■
Partially fill the Main Wash
section (7 tsp or 35 g)
■
Fill the Pre-Wash section
(4 tsp or 20 g)
For normal and heavily
soiled loads
■
Partially fill the Main Wash
section (7 tsp or 35 g)
■
Fill the Pre-Wash section
(4 tsp or 20 g)
For normally and
heavily soiled loads
■
Fill the Main Wash section
(8 tsp or 40 g)
■
Fill the Pre-Wash section
(4 tsp or 20 g)
■
Turn the rinse aid dispenser to a
higher setting. See “Rinse Aid
Dispenser” later in this section.
1. Cover latch
2. Rinse aid dispenser
3. Indicator window
3.
Add rinse aid until the indicator window looks full.
4.
Clean up any spilled rinse aid with a damp cloth.
5.
Close the cover.
NOTE:
The cover latch clicks when the cover is closed and
latched.
Rinse aid setting
The amount of rinse aid released into the final wash can be
adjusted. The factory setting is at 2. For most water conditions,
set the adjuster to 1 or 2. If there are rings or calcium (hard water)
spots on dishes, try a higher setting.
To adjust the setting
Open the dispenser cover. Turn the adjuster inside the dispenser
to the desired setting.
NOTE:
Fill amounts shown are for standard powdered detergent.
Amounts may vary if you use liquid or concentrated powdered
detergent. Follow instructions on the package when using liquid
dishwasher detergent or concentrated powdered detergent.
9
Dishwasher Efficiency Tips
Cancel
Hot water dissolves and activates the dishwashing detergent.
Hot water also dissolves grease on dishes and helps glasses dry
spot-free. Is the water temperature too low? For best
dishwashing results, water should be 120°F (49°C) as it enters
the dishwasher. Loads may not wash as well if the water
temperature is too low. Water that is too hot can make some soils
harder to remove and cause certain detergent ingredients not to
function. If your water heater is located far from the dishwasher, it
may be necessary to run the hot water at the faucet closest to the
dishwasher to minimize the amount of cold water in the water
line.
To check water temperature
1.
Run hot water at the faucet closest to your dishwasher for at
least 1 minute.
2.
Place a candy or meat thermometer in a glass measuring
cup.
Temperatures indicate where extra heat is added.
Water usage is shown in
This model meets the E
U.S.
gallons/liters.
NERGY STA R
®
guidelines for energy
efficiency.
Cycle time includes dry time. An asterisk ( * ) by the cycle time
indicates the cycle time might be longer depending on the
temperature of the water entering the dishwasher. The cooler the
water, the longer the cycle time. If the water is already hot
enough, the cycle time will be as shown.
Use this cycle for
heavily-soiled pots,
pans, casseroles,
regular tableware and
harder than normal
Use both detergent
dispenser sections.
water conditions.
Pre-
Wash
Main
Wash
RinseRinseFinal
Heated
Rinse
DryTime
(min)
Water
Usage
(gal/L)
3.
Check the temperature on the thermometer as the water is
running into the cup.
■
To save water, energy and time, do not rinse dishes before
putting them into the dishwasher.
■
Use the Normal cycle whenever possible. This cycle uses
less hot water and energy than other cycles.
■
Use a delay feature (on some models) to run your dishwasher
during off-peak hours. Local utilities recommend avoiding
heavy usage of energy at certain times of day.
■
During the summer, run your dishwasher at night. This
reduces daytime heat buildup in the kitchen.
■
Use an air dry, or an energy-saving dry option whenever
possible. Allow longer drying times (overnight) when using
these options. Use a rinse aid to improve drying.
■
Use cycles or options that add extra heat to the wash or rinse
portion of the cycle only when needed.
■
Run your dishwasher with full loads. Run a rinse cycle after
meals until the dishwasher is full.
■
If your home is equipped with a water softener, you may want
to avoid starting the dishwasher during the regeneration of
the softener, as this may contribute to poor wash
performance.
●
130°F
(54°C)
●
140°F
(60°C)
●●
140°F
(60°C)
●
89*6.9/26
Use this cycle for loads
with normal amounts of
food soil. (The energy-
Use both detergent
dispenser sections.
DryTime
Rinse
140°F
(60°C)
●
(min)
79*5.9/22.3
Pre-
Wash
●●
usage label is based on
this cycle.)
Main
Purge†RinseFinal
Wash
120°F
(49°C)
●●
Heated
Use this rinse cycle for
rinsing dishes, glasses,
and silverware that will
not be washed right
away.
Pre-
Wash
†
RinseMain
●
Wash
A small amount of water is run through the pump to remove
RinseFinal
Heated
Do not use detergent
with this cycle.
DryTime
Rinse
(min)
101.8/7
soil particles between the main wash and final rinse.
Water
Usage
(gal/L)
Water
Usage
(gal/L)
Cycle Selection Charts
Select the wash cycle and options desired. Or press START to
repeat the same cycle and options as the previous cycle.
NOTE:
If the last cycle you completed was a rinse cycle, the
dishwasher will run the last full wash cycle and options that you
selected when you press Start.
■
If the power is off or the door is open for an extended period
of time, the Start button memory will default to the Normal
cycle with heated drying.
■
If you do not run the dishwasher daily, close the door to
maintain memory.
A “●” shows what steps are in each cycle.
10
Canceling a Cycle
1.
Carefully open the door slightly to stop the cycle. Wait for the
spraying action to stop before opening the door to access the
control panel.
2.
Press
Cancel glows.
3.
Close the door. The dishwasher starts a 2 minute drain (if
needed). Let the dishwasher drain completely.
To stop the drain
You can press CANCEL again to stop the drain. Remember to
drain the dishwasher before starting a new cycle.
To clear the indicators
Press CANCEL before starting the dishwasher to clear all options
and cycles.
Changing a Cycle or Setting
During the first minute of a cycle
1.
Open the door.
2.
Press a new cycle and/or options.
3.
Check the detergent dispensers. They must be filled properly
for the new cycle.
4.
Close the door. The dishwasher resumes the new cycle
and/or option after a 5 second pause.
After the first minute of a cycle
1.
Carefully open the door slightly to stop the cycle. Wait for the
spraying action to stop before opening the door to access the
control panel.
2.
Press
Cancel
Cancel glows.
3.
Close the door. Your dishwasher starts a 2 minute drain (if
needed). Let the dishwasher drain completely.
4.
Select a new cycle and/or options.
5.
Press START.
6.
Check the detergent dispensers. They must be filled properly
for the new cycle.
7.
Close the door.
Adding Items During a Cycle
You can add an item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the cover is still
closed, you can add items.
Hi-Temp Scrub
Select this option to heat the water during parts of the cycle, and
add a rinse. Higher water temperatures and an extra rinse helps
clean tough soils. Hi-Temp Scrub, with the Heavy cycle, raises
the water temperature in the prewash and main wash. Hi-Temp
Scrub, with the Normal cycle, raises the water temperature in the
main wash.
This option adds heat, water and wash time to a cycle.
NOTE:
cycles.
Hi-Temp Scrub is an option with the Heavy and Normal
ENERGY SAVER™ Dry
Select this option to dry dishes without heat and save energy.
ENERGY SAVER™ Dry is useful when loads contain plastic
dinnerware that may be sensitive to high temperatures.
The dishes take longer to dry and some spotting can occur. For
best drying, use a liquid rinse aid. Some items (such as plastics)
may need towel drying.
NOTE:
SAVER™ Dry is an option with all other cycles.
Rinse Only automatically uses this option. ENERGY
Control Lock
Use the Control Lock to prevent unintended use of the
dishwasher. You can also use the control lock feature to prevent
unintended cycle or option changes during a cycle.
When Control Lock is lit, all buttons are disabled.
NOTE:
The dishwasher door can be opened while the controls
are locked.
To turn on the Lock
Press and hold
To add items
1.
Carefully open the door slightly to stop the cycle. Wait for the
spraying action to stop before opening the door.
2.
Open the door. If the detergent dispenser cover is still closed,
add the item.
3.
Close the door firmly until it latches. The dishwasher resumes
the cycle after about a 5 second pause.
Option Selections
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn the option off.
Select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
any time before drying begins.
Press START to repeat the same cycle and options as the
previous wash cycle.
NOTE:
If the last cycle you completed was a rinse cycle, when
you press Start, the dishwasher runs the last full wash cycle and
options.
for 4 seconds. Control Lock glows.
If you press any pad while your dishwasher control is locked, the
light flashes 3 times.
To turn off the Lock
Press and hold ENERGY SAVER™ Dry control for 4 seconds. The
light turns off.
IMPORTANT:
■
Operate your dishwasher only when you are at home.
■
If your home is equipped with a water softener, do not start
the dishwasher during the regeneration of the softener.
Status Indicators
Clean
CLEAN glows when a cycle is finished. The light turns on when
you open the door. The light turns off when you close the door or
press CANCEL.
11
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.