KitchenAid KUDE60FVPA, KUDE70FVPA, KUDS50FVPA, W10056407A, KUDS40FVPA User Manual

INSTALLATION INSTRUCTIONS

UNDERCOUNTER DISHWASHER INSTRUCTIONS D'INSTALLATION

LAVE-VAISSELLE SOUS PLAN DE TRAVAIL

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Table des matières . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

W10056407A

Table of Contents

You Need to:

• Slowly open dishwasher door while someone grasps the rear of the dishwasher. Remove shipping materials, drain hose and lower rack. Close dishwasher door until latched.

• Observe all governing codes and ordinances.

• Install this dishwasher as specified in these instructions.

• Installation should be performed by a qualified service

technician. The dishwasher must be installed to meet all electrical and plumbing national and local codes and ordinances.

Installation Instructions

(cont.)

Install the Door Handle (on some models) . . . . . . . . . . . 14

Custom Panel Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 14

Install Custom Panel - Option 1 . . . . . . . . . . . . . . . . . . . . 15

Install Custom Panel - Option 2 . . . . . . . . . . . . . . . . . . . . 16

Choose Attachment Option. . . . . . . . . . . . . . . . . . . . . . . . 17

Move Dishwasher Into Cabinet Opening. . . . . . . . . . . . . 18

Connect to Water Supply . . . . . . . . . . . . . . . . . . . . . . . . . 20

Connect to Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Make Direct Wire Electrical Connection. . . . . . . . . . . . . . 21

Secure Dishwasher in Cabinet Opening . . . . . . . . . . . . . 23

Complete Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Check Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

If Dishwasher Does Not Operate . . . . . . . . . . . . . . . . . . . 25

Additional Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Dishwasher Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Tools and Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Location Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Drain Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Water Supply Requirements. . . . . . . . . . . . . . . . . . . . . . . . 6

Electrical Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Prepare Cabinet Opening—Existing Utilities. . . . . . . . . . . 7

Prepare Cabinet Opening—New Utilities. . . . . . . . . . . . . . 7

Prepare and Route Water Line . . . . . . . . . . . . . . . . . . . . . . 8

Install Drain Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Install Moisture Barrier (on some models) . . . . . . . . . . . 10

Prepare Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Make Power Supply Cord Connection . . . . . . . . . . . . . . . 12

Determine Cabinet Opening . . . . . . . . . . . . . . . . . . . . . . . 13

DISHWASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

follow instructions.

can be killed or seriously injured if you don't

You instructions.

Tools and Parts

Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

All Installations

Tools needed:

*Must be the proper size to connect your household wiring

to 16-gauge wiring in dishwasher

Other useful items you may need:

Parts supplied:

Make sure all these parts are included in the literature package.

Parts needed:

4 #10 x 1/2" wood screws (if installing custom front panels)

INSTALLATION REQUIREMENTS

90° Elbow fitting with 3/8” N.P.T. external threads (the other end must fit your water supply line)

Teflon® tape or pipe joint compound

1 1/2”–2” (38.1–5.0 cm) Screw-type clamps (3 max)

Masking or duct tape

2 #8x1-3/8” Torx® T15 screws 4 #10x3/8” hex-head screws

Other parts you may also need:

NOTE:

Parts available for purchase in plumbing supply stores. Check local codes. Check existing electrical supply. See “Electrical Requirements” section. It is recommended that electrical connections be made by a licensed electrical installer.

In addition, for first-time installations

Tools needed:

Parts needed:

Additional parts supplied with top-venting models only:

Additional parts supplied with certain models only:

Make sure all these parts are included in the literature package. If parts are not included, call 1-800-422-1230.

® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company. †® TORX is a registered trademark of Acument Intellectual Properties, LLC.

Pliers

Phillips screwdriver

5/16” and 1/4” nut drivers or hex sockets

Measuring tape or ruler

10” adjustable wrench that opens to

1.18” (2.9 cm)

If installing custom front panels, Torx T15 screwdriver

Flashlight

Flat-blade screwdriver

Utility knife

UL listed or CSA approved twist-on wire connectors*

Small level

5/8” open-end wrench

Bath towel

Electric drill with 1/2”, 3/4” and 1 1/2” hole saw bits

Copper tubing (3/8” O.D. suggested) or flexible braided water supply line

See “Electrical Requirements” section For Direct Wire:

use UL listed or CSA approved strain relief to fit 7/8” (2.2 cm) hole

Small

tubing cutter

For Power Supply Cord: use UL listed power supply cord kit marked for use with dishwasher

Wire stripper

Shallow pan

2 - Drain hose clamps (1 large and 1 small)

Silver

Green

Wood block

Drain hose

2 - #10 x 1/2” Phillips-head screws

Bottom sound pad (located in lower rack)

Moisture barrier tape

Location Requirements

Grounded electrical supply required. Do not run drain lines, water lines or electrical wiring where

they can interfere with or contact dishwasher motor or legs. The location where the dishwasher will be installed must

provide clearance between motor and flooring. Motor should not touch the floor.

Do not install dishwasher over carpeted flooring. Shelter dishwasher and water lines leading to dishwasher

against freezing. Damage from freezing is not covered by the warranty.

A side panel kit is available from your dealer for installing your dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part Number 4396277) is available from your dealer for installing underneath the countertop, but is not required. Call 1-800-422-1230 to order.

Check location where dishwasher will be installed. The location must provide:

• easy access to water, electricity and drain.

• convenient access for loading and unloading dishes.

Corner locations require a 2” (5.1 cm) minimum clearance between the side of the dishwasher door and the wall or cabinet.

• square opening for proper operation and appearance.

• cabinet front perpendicular to floor.

• level floor. (If floor at front of opening is not level with

floor at rear of opening, shims may be needed to level dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions and ensure dishwasher is level if the floor in the dishwasher opening is uneven (example: Flooring extends only partway into opening).

NOTE: To avoid shifting during dishwasher operation, shims must be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a location where it may be subject to freezing, have it winterized by authorized service personnel.

Make sure pipes, wires and drain hose are within the shaded area shown in the “Product and Cabinet Opening Dimensions” section.

Product and Cabinet Opening Dimensions

NOTE: Shaded area of cabinet walls show where utility connections may be installed.

*Measured from the lowest point on the

underside of countertop. May be reduced to 33 7/8” (86 cm) by removing wheels from dishwasher.

**Minimum, measured from narrowest point of

opening.

23 7/8”

24 7/8”

(63.2 cm)

24 1/2”

(62.2 cm)

(60.6 cm)

33 7/8”

(86 cm) min

with wheels

removed

3/4”

(1.9 cm)*

*Insulation may be compressed (not used on all models)

21”

53.3 cm)

(

”

(61 cm)

Check that all surfaces have no protrusions that would prohibit dishwasher installation.

24”

(61 cm)**

34”

(86.4 cm)

min*

4”

(10.2 cm)

”

(7.6 cm)

6 3/4”

(17.2 cm)

1 3/4

(4.4 cm)

”

2 1/2

(6.4 cm)

”

10 1/2

(26.7 cm)

”

6 1/4”

(15.9 cm)

”

1 3/4

(4.4 cm)

lear

Are a

”

(5.1 cm)

Drain Requirements

• A new drain hose is supplied with your dishwasher. If this is not long enough, use a new drain hose with a maximum length of 12’ (3.7 m) (Part Number 3385556) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1” (2.5 cm) drain connector of the dishwasher.

• Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20” (50.8 cm) minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter, or be connected to an air gap.

• Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20” (50.8 cm) above subfloor or floor.

• Use 1/2” minimum I.D. drain line fittings.

• If required, the air gap should be installed in accordance

with the air gap installation instructions. When you are connecting the air gap a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.

Water Supply Requirements

• A hot water line with 20-120 psi (138-862 kPa) water pressure can be verified by a licensed plumber.

• 120°F (49°C) water at dishwasher.

• 3/8” O.D. copper tubing with compression fitting or

flexible braided water supply line (Part Number 4396897RP)

NOTE:

1/2” minimum plastic tubing is not recommended.

• A 90° elbow with 3/8” N.P.T. external pipe threads on one

end.

• Do not solder within 6” (15.2 cm) from water inlet valve.

Use of air gap

Air gap

Electrical Requirements

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70 - latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from: National Fire Protection Association One Batterymarch Park Quincy, MA 02269

You must have:

• 120-volt, 60 Hz, AC-only, 15 or 20 amp, fused electrical supply.

• copper wire only.

We recommend:

• a time-delay fuse or circuit breaker.

• a separate circuit.

If connecting dishwasher with a power supply cord:

• Use UL listed power supply cord kit (Part Number

4317824) marked for use with dishwasher.

• Power supply cord must plug into a grounded 3 prong outlet, located in the cabinet next to the dishwasher opening. Outlet must meet all local codes and ordinances.

If connecting dishwasher with direct wiring:

• Use flexible, armored

or nonmetallic sheathed, copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances.

• Use a UL listed or CSA approved strain relief.

Pref rred location

Optional location

Drill a 1 1/2” (3.8 cm) hole in cabinet side or rear. See product and cabinet opening dimensions.

NOTE: A grounded 3 prong outlet is required inside a cabinet next to the dishwasher cabinet opening.

Water line

Cable

Do you already have utility hookups?

Existing utility hookups No existing utility hookups

Yes —Follow instructions in the “Prepare Cabinet

Opening—Existing Utilities” section.

No —Follow instructions in the “Prepare Cabinet

Opening—New Utilities” section.

Prepare Cabinet Opening—New Utilities

What type of electrical connection will you use?

Power Supply Cord: Follow Option A instructions

Direct Wire: Follow Option B instructions

Prepare and route the electrical supply

Option A, Power Supply Cord:

If the water line and the cable extend to the locations shown, proceed to the “Install Drain Hose” section. If they do not reach far enough, follow the instructions in the “Prepare Cabinet Opening—New Utilities” section.

Prepare Cabinet Opening—Existing Utilities

INSTALLATION INSTRUCTIONS

WARNING

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

Disconnect power

Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher

Check water and electrical

placement

Water line

(15.2

6”

cm)

Cable

Power Supply Cord-Drill hole

Optional location

Pref rred location

Preferred location

1 1/2”

(3.8 cm)

6”

(15.2 cm)

Direct Wire–Route cable

Route cable from power supply through cabinet hole (cable must extend to the right front side of cabinet opening). Tape cable to the floor in area shown. This will prohibit cable from moving when dishwasher is moved into cabinet opening.

Wood

cabinet

Metal

cabinet

Power Supply Cord–Prepare hole

Wood cabinet: Sand hole until smooth. Metal cabinet: Cover hole with grommet included with

power supply cord kit.

Preferred locations

Optional locations

Drill a 1/2” (1.3 cm) hole in the cabinet side or rear.

Helpful Tip: Routing the water line through the left side of cabinet opening will make water connection easier.

Hot water line

Measure water supply line

Measure overall length of copper tubing or flexible braided water supply line. Attach to the hot water line using a connection configuration that is in compliance with local codes and ordinances. The water line to the dishwasher should have a manual shutoff valve.

Prepare and Route Water Line

Preferred location

Drill a 3/4” (1.9 cm) hole in right-hand cabinet side or rear. See product and cabinet opening dimensions.

Wood

cabinet

Metal

cabinet

Direct Wire–Prepare hole

Wood cabinet: Sand the hole until smooth. Metal cabinet: Cover hole with grommet (not provided).

Helpful Tip: Wiring the dishwasher will be easier if you route the cable into the cabinet opening from the right side.

Option B, Direct Wire:

Direct Wire–Drill hole

Optional location

Preferred location

3/4”

(1.9 cm)

Drill hole

Preferred locations

Optional locations

1/2”

(1.3 cm)

Slowly turn water shutoff valve to “ON” position. Flush water into a shallow pan until clear to get rid of particles that could clog the inlet valve. Turn shutoff valve to “OFF” position.

If needed, drill a 1 1/2” (3.8 cm) diameter hole in cabinet wall or side of the opening closest to the sink.

Connect drain hose to waste tee or waste disposer using one of the following options:

• Option A, Waste disposer – no air gap

• Option B, No waste disposer – no air gap

• Option C, Waste disposer – with air gap

• Option D, No waste disposer – with air gap

Connect drain hose

Install Drain Hose

IMPORTANT: Always use a new drain hose. Check local codes to determine if an air gap is required.

Drain trap

Disposer inlet

1. Using a hammer and screwdriver, knock plug into disposer.

2. Use needle nose pliers to remove plug.

3. Attach drain hose to disposer inlet with large silver drain hose clamp (provided). Use pliers to squeeze clamp open and move into position.

Option A, Waste disposer – no air gap

Route drain hose as shown through hole in cabinet to the front center of opening where drain connection will be made. Tape drain hose to the floor in area shown. This will prohibit it from moving when dishwasher is moved into cabinet opening.

IMPORTANT: The drain hose connection of the disposer or a waste tee must be made before the drain trap and at least 20” (50.8 cm) above the floor where the dishwasher will be installed.

Helpful Tip: To reduce vibration of the hose, keep the hose away from the floor.

Route water supply line

Slowly route water supply line through hole in cabinet. (If using copper tubing, it will bend and kink easily, so be gentle.) It should be far enough into the cabinet opening to connect it to the dishwasher inlet on the front left side of the dishwasher.

Flush water supply line

Route drain hose

Drain hose

Drill hole

Waste disposer – no air gap

Disposer inlet

Drain trap

Large silver

drain hose clamp

Drain hose

1-1/2”

(3.8 cm)

Air gap

Large silver drain

hose clamp

(provided)

Drain trap

Air gap

Large silver drain

hose clamp

Drain hose

Drain trap

Rubber hose

connector

Screw-type clamps

Screw-type clampsScrew-type clamps

Waste tee

No waste disposer – with air gap

1. Connect black end of drain hose to air gap and cut if needed. (Do not cut ribbed section.)

2. Attach drain hose to air gap with large silver drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain hose was cut, use a 1 1/2” to 2”(3.8 to 5 cm) screw-type clamp (not provided).

3. Use a rubber hose (not provided) with screw-type clamps (not provided) to connect from waste tee to air gap.

Air gap

Large silver drain

hose clamp

(provided)

Disposer inlet

Air gap

Large silver drain

hose clamp

Drain hose

Drain trap

Rubber hose

connector

Disposer inlet

Waste disposer – with air gap

Screw-type clampsScrew-type clampsScrew-type clamps

Option C, Waste disposer – with air gap

Option D, No waste disposer – with air gap

Screw-type

clamp

Drain trap

Large silver

drain hose clamp

Drain hose

Drain trap

Waste tee

No waste disposer – no air gap

Waste tee

1. Connect black end of of drain hose to waste tee and cut if needed. (Do not cut ribbed section.)

2. Attach black end of drain hose to waste tee with a large silver drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain hose was cut use a 1 1/2” to 2” (3.8 to 5 cm) screw-type clamp (not provided).

Option B, No waste disposer – no air gap

1. Using a hammer and screwdriver, knock plug into disposer.

2. Use needle nose pliers to remove plug.

3. Connect black end of drain hose to air gap and cut if needed. (Do not cut ribbed section.)

4. Attach drain hose to air gap with large silver drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain hose was cut, use a 1 1/2” to 2”(3.8 to 5 cm) screw-type clamp (not provided).

5. Use a rubber hose (not provided) with screw-type clamps (not provided) to connect from air gap to disposer inlet.

1. Make sure the area under the cabinet is clean and dry for installation of the moisture barrier.

2. Remove the backing of the moisture barrier and apply to underside of the countertop along the front edge of the counter.

Install Moisture Barrier (on some models)

Black end

Install moisture barrier (on some models)

Black end

Moisture

barrier

Apply Teflon®tape or pipe joint compound to 90˚ elbow fitting (not provided). Wrap tape around coarse threads two to four times to prohibit leaks.

Remove terminal box cover

Using a 1/4” hex head socket, nut driver or Phillips screwdriver, remove terminal box cover. Retain for later use.

Connect 90° elbow fitting to water inlet valve. Using a wrench, tighten elbow until snug, and be sure that it faces to the rear.

Excessive Weight Hazard

Use two or more people to move and install dishwasher.

Failure to do so can result in back or other injury.

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Prepare Dishwasher

Helpful Tip: Place cardboard under dishwasher until installed in cabinet opening to avoid damaging floor covering. Do not use door panel as a work table without first covering with a towel to avoid scratching the door panel.

Using two or more people, grasp sides of dishwasher door frame and place dishwasher on its back.

Using a 1/4” hex head socket, nut driver or Phillips screwdriver, remove two screws attaching access panel and lower panel to dishwasher. Do not remove tech sheet from access panel.

Apply Teflon

tape

or pipe joint compound

Coarse threads Coarse threads

Connect 90° elbow fitting to

water inlet valve

Put dishwasher on its back

Remove panels

Install a UL listed or CSA approved strain relief. Make sure screwheads are facing to the left when tightening conduit nut. Strain relief is provided with the power supply cord kit.

Option A, Power Supply Cord:

Route cord so that it does not touch dishwasher motor to lower part of dishwasher tub. Pull cord through strain relief in terminal bow. Take notice when installing or removing the dishwasher in order to reduce the chance of damaging the power supply cord.

Select UL listed or CSA approved twist-on wire connectors (included with power supply cord kit) rated to connect your household wiring to 16-gauge dishwasher wiring.

WARNING

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Remove the green grounding screw and place through the ring terminal of the green ground wire. Reattach and tighten the green screw.

NOTE: Twist on wire connector. Gently tug on wires to be sure both are secured.

Connect wires black to black and white to white, using UL listed or CSA approved twist-on wire connectors (included with power supply cord kit).

Make Power Supply Cord Connection

What type of electrical connection will you use?

Power Supply Cord: Follow Option A instructions

Direct Wire: Follow Option B instructions

Power Supply Cord—

Connect ground wire

Power Cord—Route cord

into terminal box

Ground

wire

Power Cord—Connect

Ground

wire

Washer

Ground

connector

remaining wires

Wiring configuration

If needed, see website for animated representation of this step. Visit www.kitchenaid.com under FAQ tab.

Tighten strain relief screws to secure cord.

Power Cord - Secure cord on strain relief

Place wires inside terminal box. Insert tabs on left side of cover. Make sure wires are tucked inside box. Close cover ensuring wires are not pinched. Use 1/4” nut driver and previously removed screw to secure cover.

NOTE: Do not plug into outlet until instructed to do so.

Power Cord—Reinstall terminal box cover

Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed (you will need to measure the lowest point on the underside of the countertop and the highest point on the floor). Refer to “Dishwasher Height Adjustment Chart” for wheel position and the number of turns needed.

Determine Cabinet Opening

NOTE: If the minimum cabinet opening height is less than 34”(86.4 cm), the rear wheels can be removed for additional clearance. This will allow the dishwasher to fit into a 33 7/8” (86 cm) high cabinet opening, but the dishwasher will be more difficult to move. (Measurements are approximate. Wheels and legs are preset at the factory for 34 1/2” [87.6 cm].)

Turn both leveler legs to the same height. Put wheels in the required position determined from “Dishwasher Height Adjustment Chart.”

1 2 3

wheel

Power supply wire:

white

black

ground wire

Terminal box wire: white black ground connector

Measure cabinet opening

Dishwasher Height Adjustment Chart

Cabinet

opening height

33 7/8” (86.0 cm) remove All the way up

34” (86.4 cm) 1 10

Wheel

position

Number of turns

on front leg

34 1/4” (87 cm) 2 5

34 1/2” (87.6 cm) 3 0

Adjust wheels and legs

Built-up floors (Kitchen floor height is higher than cabinet opening.) Example: Kitchen floor tile does not extend into cabinet opening. Add shims as needed in the area shown to bring the dishwasher up to 34” (86.4 cm) below the countertop.

NOTE: Shims must be securely attached to floor to avoid movement when the dishwasher is in use.

2-3/4”

(7 cm)

4”

(10.1 cm)

2”

(5 cm

)

Built-up Floors—Add

IMPORTANT: Do not scratch the front panel during this procedure.

Remove the door handle and hardware bag containing the setscrews and Allen wrench from the cardboard box. Setscrews are already installed in the handle. Place handle on mounting studs with the setscrews facing down. Push the door handle tightly against the door. Insert the short end of the Allen wrench into the setscrews. Tighten the setscrews 1/4 turn past snug.

Retain Allen wrench with Installation Instructions.

Install door handle

Mounting stud

Handle

Setscrew

(in bottom

of handle)

Allen wrench

Install the Door Handle (on some models)

Custom Panel Dimensions

IMPORTANT: You need to know what control panel is on your dishwasher before you order your custom door panel.

Follow directions under Option 1 of “Install custom panel” section.

Follow directions in Option 2 of “Install custom panel” section.

Dishwashers with control panel on top custom panel dimensions

23 1/2”

(59.7 cm)

*30 3/16” (76.7 cm)

3/4” (19.1 mm)

This dimension is for 4” (10.2 cm) toe kick. If the installation needs a higher toe kick, adjust the height of the wood panel accordingly. Not recommended for toe kicks greater than 6” (15.2 cm).

Dishwashers with control panel on front custom panel dimensions

23 3/8”

(65.8 cm)

*25 29/32” (65.8 cm)

3/4” (19.1 mm)

This dimension is for 4” (10.2 cm) toe kick. If the installation needs a higher toe kick, adjust the height of the wood panel accordingly. Not recommended for toe kicks greater than 6” (15.2 cm).

1/8” (3.2 mm)

shims as needed

(Models KUDS40FVPA, KUDS50FVPA, KUDE60FVPA, and KUDE70FVPA)

NOTE: The handle for the custom panel is not included.

IMPORTANT: If the handle is attached from the back of

the custom panel, the screw holes should be countersunk for the screws heads to be flush with the panel. If the handle is attached to the front of the custom panel, the screw lengths cannot exceed the panel thickness. For more information on KitchenAid custom handle selection, refer to the KitchenAid Catalog, visit www.kitchenaid.com, or call 1-800-422-1230.

NOTE: A customer-supplied full front panel must weigh no more than 16 lbs (7.3 kg) and must be made to specific dimensions. It is recommended that a cabinetmaker cut the custom panel because of the precise dimensions needed.

NOTE: All mounting hardware supplied is for a 3/4" (19.1 mm) thick wood panel. If a thinner wood panel, or materials other than wood are used, it is the consumer’s responsibility to obtain the proper length screws and adjust the pilot holes accordingly.

IMPORTANT: Use a moisture resistant sealer on both sides and all edges of the panel to avoid damage from humidity.

With a TORX

screwdriver, remove three screws from both sides, as shown; hold the outer panel up while removing the screws. Save screws for reinstallation.

Custom panel installation Dishwashers with control panel on the top

This dimension is for 4” (10.2 cm) toe kick. If the installation needs a higher toe kick, adjust the height of the wood panel accordingly. Not recommended for toe kicks greater than 6” (15.2 cm).

23 1/2”

(59.7 cm)

*30 3/16” (76.7 cm)

3/4” (19.1 mm)

Mark line

9 29/32”

(25.2 cm)

Top edge

Back

Gently set outer panel aside. Lay the customer-supplied custom panel face down on a covered, non-scratching surface.

Dishwashers with control panel on top custom panel dimensions

outer panel

3 screws

per side

Install Custom Panel – Option 1

Measure 9 29/32" (25.2 cm) from top edge and mark a line on the back of customer-supplied custom panel. Position the outer panel on the back of the customer-supplied custom panel as shown, so that the top holes in the outer panel are on the line, and both panels are centered side to side.

Mark pilot holes

Mark pilot

holes

Mark all four hole locations; remove outer panel. Drill 3/32" pilot holes 1/2" (13 mm) deep in customer-supplied custom panel. Place the outer panel on the back of the customersupplied custom panel; align holes.

Install the two #8-18 x 1 3/8" screws from the literature package in the top corners of the inner panel. Tighten the six side screws reinstalled in Step 6.

(Models KUDC03IV and KUDS30IV)

All models require an accessory option to attach custom panels. Kit Number 8171555 (black), 8171556 (white) or 8171557 (biscuit) are available. To order, call customer service at 1-800-444-1230.

NOTE: A custom full front panel must weigh no more than 14 lbs (6.3 kg) and must be made to specific dimensions. It is recommended that a cabinetmaker cut the custom panel because of the precise dimensions needed.

IMPORTANT: Use a moisture resistant sealer on both sides and all edges of the panel to avoid damage from humidity.

NOTE: These dimensions are for frameless custom panel models with a 4” (10.2 cm) console only.

With a TORX

screwdriver, remove three screws from both sides, as shown; hold the outer panel up while removing the screws. Save screws for reinstallation.

Custom panel installation Dishwashers with control panel on the front

23 3/8”

(65.8 cm)

*25 29/32” (65.8 cm)

3/4” (19.1 mm)

This dimension is for 4” (10.2 cm) toe kick. If the installation needs a higher toe kick, adjust the height of the wood panel accordingly. Not recommended for toe kicks greater than 6” (15.2 cm).

1/8” (3.2 mm)

Install Custom Panel – Option 2

Attach handle

Attach outer panel to back of customer-supplied custom panel with the four #10-16 x 3/8" hex head screws supplied in the literature package. Attach the handle. The handle should be centered on the front of the customer-supplied custom panel in the area shown.

IMPORTANT: Screw heads must be flush with back of customer-supplied custom panel.

Attach the panel assembly to the door by reinstalling the three screws on each side; do not tighten completely. This reinstallation of the three screws will hold the panel assembly in place on the door frame.

Align the top edge of the customer-supplied custom panel with the top of the console.

Drill two 3/32" pilot holes 1/2" (13 mm) deep, into the customer-supplied custom panel, through the holes in the

top corners on the inner panel, as shown.

6”

(15.2 mm)

Install custom panel

Align top

edges

Drill through

these holes

Hex Head

Screw

Attach body panel

Align top

Reinstall 3 screws

each side

Customer-supplied

edges

panel

Customer-supplied

panel

1-3/8” Screw

Install custom panel

Customer-supplied

panel

Drill through

these holes

Align top

edges

+ 36 hidden pages