Page 1
APPLIANCES
8546448
528138/8546448
Page 2
Table of Contents
Drawer Dishwasher Safety ............................ 2
lnstaIBation Requirements ............................. 3
Tools and Parts ................................... 3
Location Requirements ............................. 3
Water Supply Requirements ......................... 4
Electrical Requirements ............................. 4
lnstaBtation instructions .............................. 5
Prepare Cabinet Opening ........................... 5
Ebctrical Connection ............................... 5
if Installing Fbxibte Trim Pieces ....................... 8
Install Dishwasher ................................. 8
Install Drain Hose ................................. 10
Connect to Water Supply .......................... 11
Install Drawer Front Panels and Toe Panel ............. 11
Complete Installation .............................. 15
DRAWERDISHWASHERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey al! safety
messages.
This is the safety alert symbol
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word 'DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Page 3
INSTALLATIONREQUIREMENTS
Gather the required tools and parts before starting
instalhtion, Read and follow the instructions provided with
any tools listed here,
Tools needed: [] 7 mm socket wrench
[] utility knife [] 5 mm socket wrench
[] needle-nose pliers [] 5 mm open end or box end
[] tape measure wrench
[] flat-bladed screwdriver [] electric or hand drill
[] #2 Phillips screwdriver [] 1-1/2" hole saw
[] side cutting pliers [] valve (sized to fit hot water
supply line) with 3/8" male
[] pencil compression fitting
[] sandpaper [] protective floor covering
[] level
[] wood cutting board
[] adjustable wrench that
opens to 1-1/8" (29 mm)
Parts supplied:
Located in bottom drawer:
[] 2 flexible trim pieces (for sides)
[] 1 flexible trim piece (for top)
[] edge protection
[] hose clamp, hose type
[] washer
[] 2 installation brackets (top)
[] drain hose support
[] drain hose connector
[] 2 hose clamps, wire type
[] 24 #8 Phillips head wood screws
[] toe panel
[] custom toe panel mounting bracket
[] moisture protection tape
IMPORTANT: Observe all governing codes and ordinances.
Failure to meet codes and ordinances could lead to fire or
electrical shock.
Proper installation is your responsibility:
[] Contact a qualified installer to ensure that the dishwasher is
installed to meet all electrical and plumbing national and local
codes and ordinances.
[] Install the dishwasher as specified in these instructions.
[] Have everything you need to properly install dishwasher.
[] Protect dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by the
warranty.
[] This dishwasher is manufactured for indoor use only.
[] Install and level dishwasher on a floor that will hold the weight,
and in an area suitable for its size and use.
Product dimensions
22-7/16" * .__ 23-7/18"
(57cm)
raisedtabsfor
optionaltop
attaching brackets
\
(59.5 cm)
32-3/16" -
34-1/2"
(81.8 cm -
87.8 cm)
side
attaching --S
tabs
2"- 4-3/8 ....
_ 20-15/32"
_ drawer open //1_
* If custom wood panels are to be used, the product depth is specified with an
11/18'* (18 ram) door panel thickness.
** Toe panel depth: Factory supplied, 2-4-3/8" (5 - 11 cm); Custom wood, 5**
(12.7 cm) less the toe panel thickness for integrated. Minimum panel thickness
using the supplied screws is 3/8'* (9 ram).
*** Door front height: Factory supplied - 30" (76.2 cm); Custom wood - 28-1/4'*
(71.8 cm) minimum.
NOTE: Product shown with front panels for dimension purposes.
(52 cm)
(5cm - 11 cm)
Page 4
Cabinet dimensions/requirements
C-.'.'
C.'
moisture
protection tape
Utility hole:
1-1/2"(3_8crn)din.
hole, eitherside-
immediately adjacent
J tocorner. \
_ \\\\\\\
22-7/8"
(58.0cm)
,f
23-5/8"* (60_0 cm)
For dishwasher:
[] Not water line with 4.3-145 psi (30-1000 kPa) water pressure.
[] 120°F (48.8°C) water at dishwasher.
[] An easily accessible valve with 3/8" compression fitting must
be installed in the hot water supply line.
4 ,_
(10cm)
32-5/16 "- 34-5/8"
(82_0 cm - 88_0 cm)
Emectrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
typical
installation
moisture
protection tape
1/2" (12,7 ram) from
front of countertop
The 3 prong grounded outlet must be installed within 6"
(15.2 cm) to 18" (45.7 cm) of the cabinet side wall.
NOTE: The power outlet must be accessibIe after installation.
it is recommended that wood cabinetry surrounding the
dishwasher be sealed with an oil-based paint or moisture-proof
polyurethane to prevent possibIe damage from humidity.
The utility hole must be located as shown, if the hole is not
located as shown, the hoses will prevent the dishwasher from
being pushed back all the way into the cavity. Make sure the
edges of the utility hole are smooth or covered, if the utility hole
is through a metal cabinet, the hole must be protected with the
edge protector provided.
*IMPORTANT: Custom wood door panels, if used, may be wider
than the dishwasher to match surrounding cabinets. The 23-5/8"
(60.0 cm) must be increased so that there is a 1/4" (6.4 mm)
clearance between the cabinet side and panel edge.
For corner installation, there must be a !/2" (12.7 mm) space
between the adjacent cabinet doors (Le. door knobs) and open
dishwasher drawer.
GROUNDmNG mNSTRUCTmONS
For a grounded, cord-connected dishwasher:
The dishwasher must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for
electric current. The dishwasher is equipped with a cord
having an equipment-ground conductor and a grounding
plug. The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with all loca!
codes and ordinances.
WARNUNG: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative if
you are in doubt whether the dishwasher is properiy
grounded. Do not modify the plug provided with the
dishwasher; if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
For a permanentBy connected dishwasher:
The dishwasher must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminat or lead on
the dishwasher.
SAVE THESE mNSTRUCTmONS
A 120-volt, 60 Nz, AC-onty, 15 amp fused electrica! supply is
required. (Circuit breaker or time-delay fuse is recommended.) It
is recommended that a separate circuit serving only this
appliance be provided.
Page 5
GarbageDisposer:
Ifyouplantoinstallagarbagedisposer,anadditionalseparate
120-volt,60Hz,AC-only,15or20ampfusedebctricalsupplyis
required.
iNSTALLATiONiNSTRUCTiONS
Prepare the cabinet opening by applying self-adhesive
moisture protection tape to the dry dustofree underside
of the countertop,
countertop
Recommendedgroundmethod
Thisappliancemustbegrounded.Thisapplianceisequipped
withapowersupplycordhaving3pronggroundplug.To
minimizepossibleshockhazard,thecordmustbepluggedintoa
matingprongground-typeoutlet,groundedinaccordancewith
localcodesandordinances.
Option 1 : Power Supply Cord Method
taupe, moisture
1/2" (12.7 ram) from
front of countertop
2.
Turn off water supply.
g.
Decide which attaching tabs to use to secure the dishwasher.
The four side attaching tabs are recommended.
4.
if the countertop material permits and the optional top
attaching brackets will be used, install them now.
Slide the brackets under the raised tabs. Using the flat side of
the side cutting pliers, lightly tap the brackets into piace.
Make sure the locking tabs on the brackets are completely
passed through the raised tabs on the dishwasher.
mounting
bracket_
\.. locking tab
5.
if using the factory-installed power cable and plug, go to
"Electrical connection" section, Option: 1: Power Supply Cord
Method.
if direct wiring the dishwasher, go to "Electrical connection"
section, Option: 2: Direct Wiring Method.
protection tape
raised tab
Tip Over Hazard
Do not use dishwasher drawer until inside cabinet
opening.
Doing so can result in serious injury or cuts.
1. Place cardboard or other protective covering on the floor in
front of cabinet opening. Piace the dishwasher on covering.
2. Begin to route the hoses and power supply cord through the
utility hole in the cabinet.
g. Push dishwasher partway into the opening.
IMPORTANT: Push against the outside edges of drawers as
shown. Do not push against the center of the drawers.
Page 6
4, Asthedishwasherisbeingpushedintotheopening,slowly
pulltheinlethose,drainhosesandpowersupplycord
throughtheutilityhole.
5, Removethestrapfromupperdrawer.
Goto"IfInstallingFlexibleTrimPieces"section.
Option2:DirectWiringMethod
E_ectricalShockHazard
Disconnectelectrica_ power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or e_ectrical shock.
6, Rotate drawer to the right onto its side and place on the
protective cover.
(--
\ "J I
electrical cover
7, Slide the left-hand runner back into the dishwasher.
8, The electrical cover is located in the back Ieft corner.
Use a flat blade screwdriver to press the release button. Slide
the cover to the right and then pull up.
1, Place cardboard or other protective covering on the floor in
front of cabinet opening. Place the dishwasher on covering.
2, Disconnect power.
3, Open the bottom drawer.
4, Press in the right-hand runner clip and push it back about 6"
(15.2 cm). Repeat with the left-hand runner clip.
NOTE: When removing the drawer there is limited range of
movement due to the attached water hoses.
runner clip
5,
Lift the right edge of the drawer off its runner. Slide that runner
back into the dishwasher. Lift the drawer completely off the
left-hand runner.
j,_ ,,
i i
press
releasebutton
Remove factory-installed power cord,
1, Disconnect the black and white wires of the power cord from
the terminal block.
strain relief
terminal block
2, Use a 7 mm socket wrench to remove the green ground
screw. Remove the green ground wire.
3, Use a Phillips screwdriver to remove the strain relief screw.
Open the strain relief.
4, Pull the power supply cord off the dishwasher through the
back of the dishwasher.
5, Close the strain relief and replace screw so it does not
interfere with the electrical cover.
green ground screw
Page 7
6. Removethehousewiringknockout,
knockout
7, Runthehousewiringthroughtheconduitconnector(not
supplied)andintothedishwasherthroughtheknockout
opening,
8. Secure the conduit connector in the knockout opening.
ElectricalShockHazard
Connect ground wire to green ground screw.
Failure to do so can result in death or electrical shock.
11. Piace the ground wire under the green ground screw, Use a
7 mm socket wrench to securely tighten the green ground
screw,
12. Tighten the conduit connector, Replace electrical cover,
13. Pu[I the bottom drawer runners all the way out. Make sure the
latches on the back of each drawer runner are facing forward,
9, From the house wiring, strip 1/2" (13 mm) of insulation off of
each wire.
1/2"(!3 mm)
t0, insert the black supply wire and the white neutral wire into
the appropriate wire clamp on the terminal block. Securely
tighten the clamps.
terminal block
white wire
,f
black wire
/
terminal block ground wire
14, if the bottom drawer was rotated, rotate the drawer to unwind
the hoses and then put the drawer on the runners making
sure the hoses are looping upward.
15, Make sure both runner clips have snapped into place, if they
have not, pull the runner clips forward until they do.
16, Close the bottom drawer.
Page 8
17,Usethesidecuttingplierstocutthecabletiesecuringthe
hosesandpowersupplycordtothebackofthedishwasher.
back of
dishwasher
cable tie
18, Completely remove the power supply cord and save it, in
case a power cord installation is needed in the future.
22, As the dishwasher is being pushed into the opening, slowly
pull the inlet hose and drain hoses through the utility hole. Let
the house wiring gather behind the dishwasher.
23, Remove the strap from upper drawer.
::,
If the cabinet opening is 24" wide x 34-1/2" high (61.0 cm x
87.6 cm), flexible trim pieces can be attached a!ong the top and
sides of the dishwasher. Top and side trim pieces are different
lengths.
1, Open the drawers to expose the chassis trim.
2, Center the flexible trim pieces.
top trim
Tip Over Hazard
Do not use dishwasher drawer until inside cabinet
opening.
Doing so can result in serious injury or cuts.
19, Place cardboard or other protective covering on the floor in
front of cabinet opening. Place the dishwasher on covering.
20, Begin to route the hoses through the utility hole inthe cabinet.
IMPORTANT: Push against the outside edges of drawers as
shown. Do not push against the center of the drawers.
21, Push dishwasher partway into the opening.
iBm_
side trim
piece
3, If using the optional top attaching brackets, place the trim
pieces under the attaching brackets.
4, Remove trim pieces backing paper to expose the adhesive.
5, Place the trim pieces on the trim and press.
6, Finish pushing dishwasher into opening.
Leave protective cover on floor.
2,
Open the bottom drawer.
3,
Press in the right-hand runner clip and push it back about 6"
(15.2 cm). Repeat with the left-hand runner clip.
NOTE: When removing the drawer there is limited range of
movement due to the attached water hoses.
piece
open drawer
sidetrim
piece
......chassis trim
edge
4,
runnerclip
4, Lift the right edge of the drawer off its runner. Slide that runner
back into the dishwasher.
5, Lift the drawer completely off the left-hand runner.
Page 9
6,
Rotate the drawer to the right onto its side and place on the
protective cover.
i
7,
Slide the left-hand runner back into the dishwasher.
8.
Reach inside the dishwasher to adjust the feet using a 5 mm
open end, box end, or socket (if space permits) wrench.
Adjust for cabinet height and level. Place a level on the drawer
runners. Level the dishwasher to within 3/32" (2.4 mm) from
front to back.
3/32" (2.4 ram) minhq'_um
clearance to underside of counter_
T
Choose attachment option
Option 1: Side attachment
1. The dishwasher side attaching tabs are accessed through
holes in the sound insulation.
IMPORTANT: For best installation, use all four attaching tabs.
2. Secure the attaching tabs to the cabinet using #8 Phillips
/
head screws.
side
3. Pull the bottom drawer runners all the way out. Make sure the
latches on the back of each drawer runner are facing forward.
(
!
ii
9,
Place a level across the drawer runners. Level the dishwasher
to within 3/32" (2.4 mm) from side to side.
4. Ifthe bottom drawer was rotated, rotate the drawer to unwind
the hoses and then put the drawer on the runners making
sure the hoses are looping upward.
5. Make sure both runner clips have snapped into place. If they
have not, pull the runner clips forward until they do.
6. Close the bottom drawer.
Page 10
Option 2: Top attachment
1, If the top attaching brackets are used, open the top drawer
slightly:
2, Screw the top attaching brackets to the underside of the
counter with two #8 Phillips head screws.
IMPORTANT: The top attaching brackets can accommodate
a maximum 3/4" (19 mm) vertical gap.
.......top attaching bracket
3, Close the top drawer,
Option 1: Sink drain waste tee connection
1, Route the drain hoses as shown and press the hoses into
the drain hose support.
2, Decide if the drain hoses need to be trimmed, If they do,
trim them,
3, Slip a wire clip over each drain 7_ wireclip
hose. Push the hoses into the
drain hose connector firmly,
5 ciicks,
4, Position the wire clips between
the two positioning ribs on the drain hose
drain hose connector, connector
5, Attach the drain hose connector to the waste tee using
the supplied hose clamp,
6, Attach the drain hose support bracket to the cabinet with
a #8 Phillips head screw at the height shown below,
NOTE: The drain hose connector must not support the weight
of excess hose length. Keep hoses as fully extended as
possible.
Option 2: Garbage disposaB connection
1, Route the drain hoses as shown and press the hoses
into the drain hose support,
2,
Decide if the drain hoses need to be trimmed, If they do,
trim them,
3,
Slip a wire clip over each drain
50 wire clip
hose, Push the hoses into the
drain hose connector firmly,
5 clicks,
4,
Position the wire clips between
the two positioning ribs on the
drain hose connector,
5,
Attach the drain hose connector to the garbage disposal
wire clip ¢_
drainhose
connector
using the supplied hose clamp,
6,
Attach the drain hose support bracket to the cabinet with
a #8 Phillips head screw at the height shown below,
NOTE: The drain hose connector must not support the
weight of excess hose length. Keep hoses as fully extended
as possible.
o_
!
oE
water supply
10
.....8" (20,3 cm) rain. bend
radius from valve
Option 3: Air break connection
1, Route the drain hoses as shown,
2,
Decide if the drain hoses need to be trimmed, If they do,
trim them,
3,
Slip a wire clip over each drain
#_) wire clip
hose, Push the hoses into the
drain hose connector firmly,
5 clicks,
4,
Position the wire clips between
the two positioning ribs on the
wire clip U
drain hose connector,
drainhose
connector
Page 11
5. Attachthedrainhoseconnectortotheairbreakusing
thesuppliedhoseclamp,
EJ_ air break
E
drain hose
connector
waste
water supply
8" (20.3 cm) min. bend
radius from valve
install the flat seal washer on the end of the inlet hose.
Connect the inlet hose to the water supply valve. Tighten
securely.
2,
Turn the water valve on and check for any leaks.
1. Remove front panels from box and discard all shipping
material.
2. On the shorter front panel (lower drawer), remove the
tape securing the connector and wires. Discard tape.
3. Connect the end of the medallion connector to the
connector from the lower drawer.
wire
opening
lowerfront
panel
end of medallion
connector
4,
Gently feed the wires and connectors into the metal plate
wire opening.
5,
Line up front panel tabs to slots in metal plate, Do not
puii the connector from wire opening,
va,ve0 f,atsea,
3, Open top drawer. Remove the packing tape from the front
and rear of dish rack.
4, Close drawer.
5, Open bottom drawer. Remove the packing tape from the front
and rear of dish rack.
6, Close drawer.
slots _ "- front panel
._.__.... _'_m ata, plat e \_
6. Push the front panel down to lock in place.
7. Repeat steps 2-6 for the top drawer panel.
8. When installed properly, top panel should be even with
top of dishwasher with a 3/8" (9.5 ram) gap between the
top and bottom panel
11
Page 12
Option1:Insta{Istandardtoepane{
NOTI=S:Dependingoncountertopheight,youmaynothaveto
trimthetoepanel.
Rugsplacedinfrontofdishwashercouldinterferewith
toepanel.Clearancebetweenfloorandtoepanelmay
needtoincludetherugthickness.
1. Partiallyopenthebottomdrawer.
2. Turnthetoepanelupsidedownandholdverticallyagainstthe
bottomedgeofthetubside(notthefront).
3. Onthetoepanel,markwherethetub'sbottomedgeis.
7,
Remove any rough edges by sanding smooth,
8,
Partially open bottom drawer. Position toe panel behind door
and slide onto the underside of tub.
toe panel clamping (_
mountingrail screw
Close the drawer. Check that there is
1/2" (12.7 mm) minimum clearance
between the bottom edge of the toe
panel and the floor.
if not, remove the toe panel and shorten
using the utility knife. Remove any rough
edges.
10. Slide toe panel back onto mounting rails.
ss{{_ i (12_7 mm)
floor
bottom edge
of tub side
4,
On a stable surface, place toe panel on a wooden cutting
board and pick the closest groove to the mark. Ifthe mark is
between two grooves, choose the groove that makes the toe
panel the shortest.
5,
At the selected groove, use a utility
knife and cut the vertical rib the
length of the toe panel until entire
piece is removed.
6,
Snap off the toe panel tabs. toepanel
toe panel
11. If needed, you may simply push the toe panel back or forward
on the mounting rail.
12. With a Phillips screwdriver, tighten the toe panel clamping
screws on both sides.
13. Plug in dishwasher or reconnect power.
14. Go to "Complete Installation" section.
ear of
12
tabtoepanel
Page 13
Option 2: Install custom front panels
Custom front panem dimensions
9 ==
I"_-- (22.9cm)
medallion
cutout area
Top panel
(frontview)
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
2-5/16"
(5_9cm)
1. Prepare the custom front panels to specifications shown.
2. Mount the handle to the custom panel.The screws must
not extend beyond the back surface of the panel. (Handle
is customer supplied, location is customer preference.)
3. Lay the custom front panel face down on a protective
covering.
4. Measure and mark the vertical centedine and horizontal
position line on the back of the front panels.
_(_ _ark
TopPanel- _ horizontalline
1-7/16" (36.5ram) _ mark
Bottom panel-
1-3/16" (30.2ram) centerline
23-7/16" (59.5 cm)
medallion
cutout area
Bottom panel
(frontview)
23-7/18" (59.5cm)
1-7/32" (32.8 mm)
1_9/32"
2-13/32"
(60.8ram)
Medallion cutout
(frontof panel)
2-1/8"
NOTE: Do not cut
beyond outline of
medallion cutout_
Rout a 1/4" (6,4 ram)
radius around back side
--1-13/84" of medallion cutout,
(30_6 ram)
5. Feed the wires of the medallion connector through the
front of the custom front panel and push the medallion
into the prepared medallion hole.
6. Remove the pins on both sides of the dishwasher drawer
by pulling the pins straight out with a pair of needle-
nose pliers.
pin .........
/
7. Gently pull the bottom of the metal plate away from the
dishwasher, and then pull down.
Upper and lower panel minimum thickness is 5/8" (16 mm). Panel
thickness above 11/!6" (18 mm) can be accommodated but
product depth will increase accordingly.
Custom front panel materia! must be suitable for damp
conditions or adequately sealed to withstand moisture. Using a
moisture-resistant material can provide additional protection.
Taping edges alone may not provide adequate sealing. For
painted panel, paint all rear edges to improve sealing.
8. Lay the custom front panel face dovvn,
9. Feed the medallion wires through the wire opening in
the metal plate,
wire opening
..................front panel
13
Page 14
10,LaythemetaHpilateonthebackofthecustomfront
panel
11,AHignthecenterHinemarkedonthecustompaneHwiththe
diamondshapeandnotchinthemetaHpilatetocenterthe
metaHpilatehodzontaHHy,AHignthehodzontaHHinewiththe
topofthemetaHpilate,
horizontal line
[
top of plate
centerline
15, Line up the bracket holies with the pin holies and repHace
each pin so that the pin Hine is vertical
/
16, Repeat steps 2-15 for other custom panel
Option 2: _nsta{I custom toe pane_
Oustom toe pane_ dimensions
12, Using the screws provided, fasten the metal plate to the front
panel through the 3 inner holes.
J
,Z
three
innerholes
13, Connect the medaHHion connector to the dishwasher
connector,
lowerfront
panel
end of rnedallic
connector
2_5/32 ,,
(55 ram)
5" (12J crn)
max,
(varies)
The black prefinished toe panel can also have a custom front
panel with a thickness from 3/8" to 3/4" (9-19 mm) attached to it.
Determine the height of the toe panel custom panel: The
minimum height is 2-3/4" (70.5 mm). Measure from the top of the
adjacent cabinet door front to the floor. Subtract 28-15/32"
(72.3 cm) for needed toe panel height.
NOTES: Depending on countertop height, you may not have to
trim the toe panel.
Rugs placed in front of dishwasher could interfere with
toe panel. Clearance between floor and toe panel may
need to include the rug thickness.
1, Prepare the custom toe panel to specifications shown above.
2, Lay the custom toe panel face down.
3, Fasten the biack plastic toe panel on the back of the custom
toe panel with the screws provided with the dishwasher.
,_ 23-1/2" (59,7 cm)
f
14, Slide the metai pilate tabs into the notches and shots on
the dishwasher and gentiy puii up to Hock in piace,
14
I i
I I
plastic
toe panel
_ustorn
toe panel
4, Partially open bottom drawer. Position custom toe panel
behind door and slide on the underside of tub.
5, Close the drawer and slide the toe panel back onto mounting
rails.
Page 15
6. Ifneeded,youmaysimplypushthetoepanelbackorforward
onthemountingrail.
7. WithaPhillipsscrewdriver,tightenthetoepanelclamping
screwsonbothsides.
toe panel clamping
mounting rail screw
8. Plug in dishwasher or reconnect power.
1. Check to be sure all parts are now installed. If there is an
extra part, go back through the steps to see which step was
skipped.
2. Check to be sure you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. Read "Dishwasher Use" in the Drawer Dishwasher Use and
Care Guide.
If dishwasher does not operate, check the following:
[] Household fuse is intact and tight; or circuit breaker has not
tripped.
[] Electrical supply is connected.
[] See "Troubleshooting" in your Use and Care Guide.
i
\
\
15
Page 16
Part No. 8546448
© 2004 KitchenAid
® Registered trademark/TM trademark of KitchenAid, U.S.A.,
KitchenAid Canada Hcensee in Canada
Benton Harbor, Michigan 49022
Printed in U.S.A.
10/2004
Loading...