How it Works
KitchenAid
Loading...
KSSS42MBX00

KitchenAid KSSS36DBW01, KSSS36DBX01, KSSS36DBX00, KSSS36MBX01, KSSS42DBW00 Installation Instructions Manual

...
36” (91 cm), 42” (106 cm)
and
48” (122 Built-In Refrigerators
cm>
these instructions.
Installation requires 2 or more people.
Important:
l
Installer: Leave Installation Instructions with the homeowner.
l
Homeowner: Keep Installation Instructions for future reference.
l
Save these Installation Instructions for the local electrical inspector’s use.
Ii
I
I I I
I I I I I I I \ \ \ \I
Part No. 2002469 Rev. A
Personal Injury Hazard
l Because of the weight and size
of the refrigerator, two or more people are required to install it.
l Most of the refrigerator’s
weight is at the top. Extra care is needed when moving the
refrigerator to prevent tipping.
Failure to follow these instructions could result in personal injury.
Floor Damage Keep cardboard shipping piece or plywood under refrigerator until
it
is installed in the operating
position. Failure to do so may cause
damage to floor covering.
Important: Observe all governing codes and ordinances.
It is your responsibility to:
l Comply with installation
specifications and dimensions.
l Properly install refrigerator. l Make sure that you have these
materials necessary for proper
installation:
l/4” (6 mm) copper tubing with
shutoff valve
l/4” (6 mm) compression fitting
6 - #8 x 3” (76
mm) wood screws
(Longer screws may be
required.)
2 - 2” x 4” x 32”
(5 cm x 10 cm x
81 cm) min. wood boards
(See Page 4.)
T-15 Torx drive and bit
l Assure that floor will support
refrigerator weight (more than 600 lb./272 kg.), door panels,
and contents.
l Provide a properly grounded
electrical outlet.
l Assure that location will permit
appliance doors to open 90” minimum.
Product Dimensions
Front View
n
A
l
Dimensions shown are for levelers extended l/8” (3 mm)
below rollers. For levelers fully extended l-1 /4” (32 mm)
below rollers, add l-l /8” (29 mm) to this dimension.
Page 2
Top View
if .:+:;.. H
,*:
,’ :­:i :a
:: :: :: ::
I’
:: :: :: ::
I’
I’ :a
::
::
::
.’
m:
:I
a’
5.4
Side View
::. c
j:j .._........ .._. D .._.... i:;:.:.
i;
.:
:.::
Dispenser and Non-Dispenser Models
36” (91 cm)
42” (106 cm)
48” (122 cm)
A 36”
(91 cm)
42” (106 cm)
48” (122 cm) B 83-S/8” (212 cm)* 83-S/8” (212 cm)’ 83-5/8” (212 cm)* C 25-318” (64 cm)
25-3/S” (64 cm).
25-318” (64 cm) D 23-l/2” (60 cm) 23-l/2” (60 cm)
23-l/2” (60 cm) E 3-l/2” (9 cm)*
3-l/2” (9 cm)*
3-l/2” (9 cm)’
. I
. . I
F 83-l/4” (211.5 cm)’ 83-l/4” (211.5 cm)* 83-l/4” (211.5 cm) C 24” (61 cm)
24” (61 cm) 24” (61 cm)
H 35” (89 cm)
41” (104 cm)
47” (119 cm)
I
25” (63.5
cm)
25” (63.5
cm)
25” (63.5
cm)
Built-in opening requirements 61 dimensions
All dimensions *l/8” (3 mm)
-
Personal Injury/Property
Damage Hazard
. Special care should be taken at
all times to prevent refrigerator
from tipping, as it is top heavy.
l A solid soffit or two, 2” x 4” x
32” (5 cm x 10 cm x 81 cm) wood boards to cover the width of the compressor cover are required above the refrigerator to prevent tipping during use.
l If solid soffit is more than 1 inch
(2.5 cm) above refrigerator, two 2” x 4” x 32” (5 cm x 10 cm x 81 cm) wood boards must be installed on the wall l/4 inch (6 mm) above the refrigerator cover. The bottom surface of the boards should be 84 inches
(213 cm) from floor. Boards must be long enough to fully cover width of compressor
cover.
Failure to follow these instructions could result in personal injury or property damage.
The built-in refrigerator can be
installed:
l with doors protruding from cabinet
front.
l with side panel(s) enclosing
refrigerator side(s).
Select one method and use dimensions given. Dimensions shown provide 0” (0 cm) clearance.
/ I
I
I
\
\
\
/ I
I
Floor: Must support refrigerator, \ contents, and door panels.
;; ;&lark stud j jj ? &cations on I .i
: lrear wall i i ;
;80” _ 90”
; ;
!;
](203-229
cm) ! :;
’ ‘above floor. ’ ’
Grounded electrical
outlet location
Grounded electrical outlet is required.
Install side panel (optional) support board on rear wall if opening depth is 25”
(1!Zi7~m)
(64 cm) or more.
,..._~;.....:,.,.,,::.: Width ........., ...,., . . . . . . . . . . . ::, ,.,::i :.., ~.~.~.~.~.~.~.~.~.~.~.~::..:.~~.~.~.~.~...’:~~.~.
Water line location
Water line must
provide 15-I 00 psi 1 -I/Z” (103-690 kPa)
(3.8
cm)
water pressure.
Rough in water
i ..:! :.:.: j
line before
;; :
:: :
installing
j;
.:::.
_
T: ‘C.
I III I.
retrigerator.
(18Tm)
. . .
..:
. . . . . . -. . .
2-l/2”
(6.3
cm)
l/2” (12 mm) hole for plumbing can be located anywhere within
* shaded area.
Opening dimensions
Model
36” (91 cm)
42” (106 cm)
48” (122 cm)
Width min. 35-l /2” (90 cm)
41-l/2” (105 cm) 47-l/2” (120 cm)
Height min.
83-l
/4” (211.5
cm) 83-l/4” (211.5 cm) 83-l /4” (211.5 cm)
Height max. 84-3/4” (215 cm)
84-3/4” (215 cm) 84-3/4” (215 cm)
Depth
23-l /8” (59 cm)
23-l /8” (59 cm)
23-l /8” (59 cm)
Page 3
Door swing dimensions
.;:;,
. . :
.%“=A
115”= B 137”=C
Front of refriaerator
::.
,:::,
I..
90” =. D 115” = E 137” = F
Tipping radius
Forward/backward ---*---* tipping radius ,=*
,*
,*’
I’
I
.’
,
.’
,
,
1.
,’
:
4’
I
__--
------------
.
L
Side
//dC
C_L-----__
tipping radius /’
I
I
J . . . ..fi.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .::.................. . ..-.. B . . . ,.i....
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i::::,
1 Size
IA
(B
36” (91 cm)
87-l /4” (222 cm)
90-I /2” (230 cm)
42” (106 cm)
87-l /4” (222 cm)
93” (236 cm)
48” (122 cm)
87-l /4” (222 cm)
96” (244 cm)
36”
42 48”
91 cm 106 cm 122 cm
D
44-314”
48-i 14”
51-314”
(114cm) (123cm) (131 cm)
F
39-314” 42” 44-l/2” (101 cm) (106cm) (113cm)
Location must permit doors to open to 90” min. Allow 1 inch (2.5 cm) min. space between refrigerator side and corner wall.
Anti-tip requirements
l/4” (6 mm) ma:
.;i.
. ..il
. .
2” (5 cm)
min.
. . . . . . . . -,:+.i.
Two, 2” x 4” x 32” (5 cm x
* 10 cm x 81 cm)
anti-tip wood boards
Attach to wall studs with six, #8 x 3” (76 mm) (or longer) wood screws.
... Boards must be
““’ long enough to
fully cover width of compressor cover.
+ rear
wall
If boards are placed before installation of refrigerator, locate boards so the bottom surface of the boards are 84 inches (213 cm) from the floor. During installation, raise the refrigerator up so there is l/4 inch (6 mm) maximum between top of refrigerator and bottom of anti-tip boards.
If solid soffit is 1 inch (2.5 cm) above refrigerator, anti-tip wood boards are not required.
If solid soffit is not available or soffit is more than 1 inch (2.5 cm) above cover, center wood boards on rear wall l/4 inch (6 mm) maximum above refrigerator. Attach wood boards to wall studs with wood screws - making sure that screws are engaged in wall studs l-l /2 inch (3.8 cm) minimum and that boards extend 2 inches (5 cm) minimum over the top rear of refrigerator compressor cover.
Page 4
1. Panel kits
Four kits, containing colored acrylic stainless steel door and top grille panels, are available through your
or
KitchenAid dealer. Follow the kit instructions for installing the panels.
Panel Kit Numbers
Model Non-dispenser
Dispenser
Size
36”/(91 cm) 42”/(106 cm) 48”/( 122 cm)
36”/(91 cm)
42”/(106 cm)
48”/( 122 cm)
White 4318635 4318636 4318637 4210464 4210570 4318424
Black 4318632 4318633 4318634
1 4210469
1 4210569
1 4318423
I
Almond 4318638 4318639 4318640 4210548 4210568 4318425 Stainless Steel 4318641 4318642 4318643 4210593 4210594 4318426
2. Custom panels
Product Damage
The custom panel weight must
NOT exceed amounts listed. Panels weighing more than
amounts listed may cause product
, damage.
NOTE: Dimensions shown have a
+ l/16” (1.5 mm) tolerance. Panels
that are more than l/4” (6 mm)
thick must be routed. If using
routed panels, add l/16” (1.5 mm) to dimensions shown.
If panels are less than l/4” (6 mm) thick, install a filler panel between doors and decorative panels.
If panels are more than l/4” (6 mm) thick, route panel edges on all sides.
;...:.:;: A ,...... . . . . . . . :+.i
Top grille panel [max. wt.: 10 lbJ(4.5 kg)]
j;:,
6
.:.;.:
..:
Freezer door panels
(with dispenser)
Maximum combined
weight of
b;c$h pa;;;:
(1f.5 kg)
..,.
,:j:,
,.....
i
:.i:
:::
. . . . . . . . . . .
..-.: iii . . F . . . . . . . . . . . ::.
Freezer
door panel
(no dispenser:
Maximum
weight:
30 ounds
(1 p.5 kg)
L
.,.
.j:.
..:.
c
xi.
::
. . .:.-.-
:+ ,.... . . . . . . . . . . ..i...i... H ii.. .i . . . 5
Refrigerator
door panel
Maximum
weight:
50 ounds
& kg)
::? i
.::‘:.
i
I
Size A 1 B 1 C D E I F G I H I
$7 cm) $:6 cm)
48”
(122 cm)
32-3talj
6” 14-l 14”
26-l 14” 34-7116”
14-l 14”
70-7/l 6” 19-l 14”
70-7/l 6”
(a2 cm)
(15 cm) (36 cm) (67 cm) (a7 cm) (36 cm)
(179 cm) (49 cm)
(179 cm)
38-3/8~~
6” 16-314”
26-l
14”
34-7/l 6” 16-314”
70-7/l 6” 22-314”
70-7/l 6”
(97 cm)
(15 cm) (43 cm)
(67 cm) (a7 cm)
(43 cm) (179 cm)
(58 cm) (179 cm)
44-318”
6”
19-114” 26-114” 34-7/l 6”
19-l 14” 70-7116” 26-114”
70-7/l 6”
(113cm) (15cm)
(49 cm)
(67 cm’, (87 cm)
(49 cm) Cl 79 cm)
(67 cm) (179 cm)
Page 5
End view of handle side of panel
Side view
Custom panels
more than l/4” (6 mm) thick: Route entire length
or selected areas of
handle side of panels 3-l /4” (8.25 cm).
Dimensions for routing panel edges
l/4”
(6
. .
3. Side panels
If side panel will be installed inside side trim and the side panel is more than l/4” (6 mm) thick, route front edge of panel to fit trim piece.
End view of side trim piece
1 /4” ,..::j:.:.
(6 mm)
l/16” <:::..
(1.5 mm)
7132”
(5.5 mm)
:.;.:
. . . .
.:
..;..
:.:.
,.y.:.
S/32” (4 mm)
.::j ‘ij
13/32” (10 mm)
side panel inside
side panel outside
side trim piece. side trim piece.
Width and height:
depend on
installation type.
Thickness:
l/2” (12 mm)
minimum to
prevent warping.
Notches for door
hinges or toe
panel
recess (if desired).
Determine
installation height
before cutting
notches.
support board
side panel outside side
\
;::
,.,., :;::
: jj:,
trim piece and recessed. *y ; ;
(64cm) j
: 24-i/8” i
:_
(61 cm) ;
j 23-l/2” i (60cm)
..,:,.
:.:.
side panel support nailer
-r
j
Spacers required for proper ventilation.
Attach three square spacers from parts
bag to top, middle
and bottom of
refrigerator side.
side trim piece
-j
ff
$
36” 42” 48”
Model (91 cm) (106 cm) (122 cm)
36” 42” 48”
A
(91 cm) (106 cm) (122 cm)
B
35-l/2” 41-l 12” 47-l /2n (90 cm) (105 cm) (120 cm)
C
35” 41” 47” (89 cm) (104 cm) (119 cm)
Page 6
Loading...
+ 14 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use