KitchenAid KSSS42FTX02, KSSS48QTX03, KSSS48QTX02, KSSS48QTX00, KSSS48QTW02 Installation Guide

...

®itchen_kid ®

SIDE BY SIDE BUILT-IN REFRIGERATOR

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.

REFRIGERADOR EMPOTRADO

DE DOS PUERTAS

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACION REQUIERE DE 20 MAS PERSONAS.

REFRIGERATEUR ENCASTRE COTE A COTE

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L'INSTALLATION NECESSITE L'INTERVENTION DE 2 PERSONNES OU PLUS.

Table of Contents/Indice/Table des matieres .................................................................. 2

2316565B

TABLEOF CONTENTS

REFRIGERATOR SAFETY ............................................................. 3

MODELS .......................................................................................... 4

INSTALLATION REQUIREMENTS ................................................ 6

Tools and Parts ............................................................................ 6

Location Requirements ................................................................ 6

Electrical Requirements ............................................................... 7

Water Supply Requirements ........................................................ 8

Tipping Radius ............................................................................. 8

Product Dimensions ..................................................................... 9

Door Swing Dimensions ............................................................. 10

Overlay Series Door Panel & Cabinetry Clearance .................... 11

Overlay Series Custom Panels and Handle Kits ....................... 13

Classic Series Factory Panels and Kits ..................................... 14

Classic Series Custom Panels ................................................... 15

Classic, Architect _ and Complete Series

Custom Side Panels ................................................................... 16

Overlay Series Custom Side Panels .......................................... 17

INDICE

SEGURIDAD DEL REFRIGERADOR ........................................... 28

MODELOS ..................................................................................... 29

REQUISITOS DE INSTALACION ................................................. 31

Piezas y herramientas ................................................................ 31

Requisites de ubicaci6n ............................................................. 31

Requisites electricos .................................................................. 32

Requisitos del suministro de agua ............................................. 33

Arco de vuelco ........................................................................... 33

Medidas del producto ................................................................ 34

Medidas de oscilacidn de las puertas ....................................... 35

Espacio para el panel de la puerta y para los gabinetes de

la serie Overlay ........................................................................... 36

Paneles a la medida y juegos de agarraderas de la serie

Overlay ....................................................................................... 38

Paneles y juegos de fabrica de la serie Classic ........................ 39

Paneles a la medida para la serie Classic ................................. 40

Paneles laterales a la medida para las series Classic,

Architect ®y Complete ................................................................ 41

INSTALLATION INSTRUCTIONS ................................................ 18

Unpack the Refrigerator ............................................................. 18

Reduce Tipping Radius .............................................................. 18

Move the Refrigerator into House .............................................. 19

Install Anti-Tip Boards ................................................................ 19

Connect the Water Supply ......................................................... 19

Plug in Refrigerator ..................................................................... 21

Move Refrigerator to Final Location ........................................... 21

Level and Align Refrigerator ....................................................... 21

Install Classic Series Custom Panels ......................................... 22

Install Overlay Series Custom Panels ........................................ 23

Adjust Doors ............................................................................... 24

Install Side Panel ........................................................................ 25

Install Base Grille ........................................................................ 25

Complete Installation .................................................................. 26

Water System Preparation ......................................................... 26

Paneles laterales a la medida para la serie Overlay .................. 42

INSTRUCCIONES DE INSTALACION ......................................... 43

Desempaque el refrigerador ...................................................... 43

C6mo reducir el arco de vuelco ................................................. 43

C6mo hacer entrar el refrigerador en la casa ............................ 44

Cdmo instalar los tableros antivuelco ........................................ 44

Conexidn del suministro de agua .............................................. 45

Crime enchufar el refrigerador ................................................... 46

C6mo mover el refrigerador a su ubicaci6n final ....................... 46

Nivelaci6n y alineamiento del refrigerador ................................. 46

Cdmo instalar los paneles a la medida para la serie Classic....47

C6mo instalar los paneles a la medida para la serie Overlay....48

Ajuste las puertas ....................................................................... 49

Cdmo instalar el panel lateral ..................................................... 50

C6mo instalar la rejilla de la base .............................................. 50

Cdmo terminar la instalacidn ..................................................... 51

Preparaci6n del sistema de agua .............................................. 51

TABLE DES MATIERES

SECURIT¢: DU RC:FRIGC:RATEUR .............................................. 52

MODELES ..................................................................................... 53

EXIGENCES D'INSTALLATION ................................................... 55

Outillage et pieces ...................................................................... 55

Exigences d'emplacement ......................................................... 55

Specifications electriques ......................................................... 56

Specifications de I'alimentation en eau ..................................... 57

Rayon de basculement .............................................................. 57

Dimensions du produit ............................................................... 58

Dimensions pour le pivotement des pores ............................... 59

Serie Overlay - Panneau de porte et placard - dimensions et

espace libre ................................................................................ 60

Panneaux personnalises et poignees de la serie Overlay ......... 62

Ensembles de panneaux d'origine de la serie Classic .............. 63

Panneaux personnalises de la Serie Classic ............................. 64

Panneaux lateraux personnalises des Series Classic,

Architect ®et Complete ............................................................... 65

Panneaux lateraux personnalises de la Serie Overlay .............. 66

INSTRUCTIONS D'INSTALLATION ............................................. 67

Deballage du refrigerateur .......................................................... 67

Reduction du rayon de basculement ......................................... 67

Faire entrer le refrigerateur dans le domicile ............................. 68

Installation de planches antibasculement .................................. 68

Raccordement a la canalisation d'eau ....................................... 69

Brancher le rdrigerateur ............................................................. 70

Deplacement du refrigerateur a I'emplacement final ................. 70

Reglage de I'aplomb et alignement du refrigerateur ................. 70

Installation des panneaux personnalises de la Serie Classic....71

Installation des panneaux personnalises de la Serie Overlay...72

Ajustement des portes ............................................................... 73

Installation du panneau lateral ................................................... 74

Installation de la grille de la base ............................................... 74

Achever I'installation .................................................................. 75

Preparation du systeme d'eau ................................................... 75

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

Side by Side Non-Dispensing Refrigerators

MODELS

Architect ®Series Features wraparound styling that complements the contoured

door handles. This series provides a warm commercial-looking built-in refrigerator.

KSSC36FTS KSSC42FTS KSSC48FTS

Classic Series

Features factory-installed, traditional style trim to provide a "framed" look. This series requires the installation of custom panels that are not included.

KSSS36FTX KSSS42FTX KSSS48FTX

Overlay Series

Features factory-installed, overlay style trim to provide a "frameless" look. This series requires the installation of custom panels, handles, and standoffs.

KSSO36FTX KSSO42FTX KSSO48FTX

Side by Side Dispensing Refrigerators

Architect ®Series

Features wraparound styling that complements the contoured door handles. This series provides a warm commercial-looking built-in refrigerator.

KSSC36QTS KSSC42QTS KSSC48QTS

_ ,:,;

N ;)

" IIIIIIIIIIIIIIJllllllllllllllllllll ;:

Classic Series Features factory-installed, traditional style trim to provide a

"framed" look. This series requires the installation of custom panels that are not included.

KSSS36QTB KSSS42QTB KSSS48QTB KSSS36QTW KSSS42QTW KSSS48QTW KSSS36QTX KSSS42QTX KSSS48QTX

Overlay Series Features factory-installed, overlay style trim to provide a

"frameless" look. This series requires the installation of custom panels, handles, and standoffs.

KSSO36QTB KSSO42QTB KSSO48QTB

Complete Series Features factory-installed stainless steel trim and panels to create

a sleek, contemporary look. KSSP36QTS KSSP42QTS KSSP48QTS

INSTALLATION REQUIREMENTS

IMPORTANT:

• Installer: Leave Installation Instructions with the homeowner.

• Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local

electrical inspector's use.

TOOLS NEEDED: Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed here.

• • Torx®tT27 screwdriver

Hand drill or electric drill (properly grounded)

Drill bits

• wrenches

Two adjustable wrenches

• • 3/_,, Allen wrench

Phillips screwdriver

• • 1/4"and 3A6"socket drivers

Small level

• • Tape measure

Appliance dolly

PARTS NEEDED:

Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed) One or two 2" x 4" x 32" (5 cm x 10cm x 81 cm) wood board(s) Order factory panels, make custom panels or consult a

qualified cabinetmaker or carpenter to make the panels. Classic Series: Order factory panels, make custom panels, or

consult a qualified cabinetmaker or carpenter to make the panels. See "Classic Series Custom Panels" for more

information. Overlay Series: Make custom panels, or consult a qualified

cabinetmaker or carpenter to make the panels. See "Overlay Series Custom Panels and Handle Kits" for more information.

Architect _ and Complete Series are shipped complete. If you are connecting the water line directly to copper tubing

and not to a shutoff valve, you need a ferrule, a union, and a r/4" (6.35 mm) compression fitting.

• rl/32"nut driver

• %" and 1/2,,open-end

• Utility knife

The refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to enclose the refrigerator.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT:

• Observe all governing codes and ordinances.

• It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source.

• Do not install in a location where the temperature will fall below 55°F (13°C).

• Floor must support the refrigerator weight, more than 600 Ibs (272 kg), door panels and contents of the refrigerator.

• Ceiling height must allow for side tipping radius. See "Tipping Radius."

• Location should permit door to open fully. See "Door Swing Dimensions."

• Location must permit top grille removal. See "Opening Dimensions."

Opening Dimensions

• To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is

higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the rear wall studs 80" to 90" (203 cm to 229 cm) above the

floor. See "Install Anti-Tip Boards" for more information. NOTE: A clearance of r/_,,(1.3 cm) must be maintained above

the top grille in order for the top grille to be removed.

1-®TORX is a registered trademark of Textron Innovations Inc.

A grounded 3 prong electrical outlet should be placed within 4" (10.2 cm) of the right side cabinets or end panel. See "Electrical Requirements" for more information.

The water shutoff should be located in the base cabinet on either side of the refrigerator or some other easily accessible

area. If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor or the back wall. See "Water Supply Requirements" for more

information.

11oo,,-9o,,

! !(2031229 cm)

;31/2.. (212.1 cm) min.

043/4'. (215 cm) max.

to bottom of solid soffit

77" (196 cm)

Width

(see chart following)

15.2 cm_,

Electdcam Shock Hazard

Pmuginto a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can resumt in death, fire, or electdcam shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. IMPORTANT: Ifthis product is connected to a GFCI (Ground

Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, remove the top grille and turn the master power switch to OFF or disconnect power at the circuit breaker

box. When you are finished, turn ON the master power switch or

reconnect power at the circuit breaker box. Then reset the control to the desired setting.

÷16. 72cm) ' ! _,152 cm_-_'_6" -1"

24"

(60.96 cm) min.

Model Width A (as shown above)

36 351/2''(90.2 cm) to 353/4'' (90.8 cm) 42 411/2"(105.4 cm) to 413/4"(106.1 cm) 48 471/2''(120.7 cm) to 473/4'' (121.3 cm)

NOTE: Flooring under refrigerator must be at same level as the room. Face of cabinetry must be plumb.

!i!'_,7_i_!i;_iiiii:_!i!!¸i_i:i!i!iil,_,i_i:_i!ii:_¸¸i_:_iIif!i,_'!!;__;i!!__::i_i!,!ii_i_i_i:'_i!_:_i_i:_i_;!i!_:_i_i_!ii::_!_

All installations must meet local plumbing code requirements. The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible area. The right-hand side is recommended. The access hole through the cabinet must be within 1/2"(12.7 mm) of the rear

wall. NOTE: If the water shut off valve is in the back wall behind

the refrigerator, it must be at an angle so that the tube is not kinked when the refrigerator is pushed into its final position.

(15.2 cm}

z cmj_ v _l_.z c

24"

(60.96 cm) min,

If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor. A 1/2"(12.7 mm) hole for plumbing should be drilled at least 6" (15.2 cm) from the right or left hand side cabinet or panel. On the floor, the hole should be no more than 1" (2.54 cm) away from the back wall. See "Connect the Water Supply."

• If additional tubing is needed, use copper tubing and check for leaks. Install the copper tubing only in areas where the household temperatures will remain above freezing.

• Do not use a piercing-type or ¾6" (4.76 mm) saddle valve which reduces water flow and clogs more easily.

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

• If your refrigerator has a water filter cartridge, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed, qualified plumber.

Be sure there is adequate ceiling height to stand the refrigerator upright when it is moved into place.

• The dolly wheel height must be added to the tipping radius when a dolly is used.

• If needed, the tipping radius can be reduced. See "Reduce Tipping Radius."

Side Tipping Radius

The side tipping radius varies depending upon the width of the model. Use the chart provided to determine the side tipping

radius. NOTE: Tip on side only.

i I

f I

Model Tipping Radius A

36 901/2" (229.9 cm) 42 93" (236.2 cm) 48 96" (243.8 cm)

r_r_J

Side View Front View

• The depth from the front of the top grille to the back of the refrigerator cabinet is 25%" (64.5 cm).

• The power cord is 84" (213 cm) long.

• The water line attached to the back of the refrigerator is 5 ft (1.5 m)long.

• Height dimensions are shown with leveling legs extended 1/8" (3 mm) below the rollers.

-- _-_(64.5 crn)

_-_(59,7 crn)_

"833/8"

(211.8 cm)

253/8''

231/2''

84" (213.4 cm) Power Cord

Width dimensions were measured from trim edge to trim edge.

Height dimensions are shown with leveling legs extended 1/8" (3 mm) below the rollers.

(211.8 cm)

,f "31/2" (8.9 cm)

*When leveling legs are fully extended to 11/4"(3.2 cm) below

rollers, add 11/8"(2.9 cm) to the height dimensions.

Top View

25%" (64.5 cm)

Model WidthA

36 35" (88.9 cm) 42 41" (104.1 cm) 48 47" (119.4 cm)

(seechart following)

Model Width A

(Trim edge to trim edge)

36 361/4'' (92.1 cm) 42 421/4'' (107.3 cm) 48 481/4'' (122.6 cm)

*When leveling legs are fully extended to 11/4"(3.2 cm) below

rollers, add 11/8"(2.9 cm) to the height dimensions.

Thelocationmustpermitbothdoorstoopentoaminimumof 90°.Allow41/2''(11.4cm)minimumspacebetweenthesideofthe refrigeratorandacornerwall.

NOTE:Moreclearancemayberequiredifyouareusingoverlay panels,customhandles,orextendedhandlesonaClassic

model. Toadjustthedoorswing,see"AdjustDoors."

36" (91.4 cm) Models

42" (106.7 cm) Models

125/_''

(32.1 cm)

371/4"

(94,6 cm)

351/2 ,,

[90.2 cm)

387/8"

(98.7 cm)l _

107/8"

(27,6 cm)

,'!/

.,L[

._- 14%"--_ |

(36.5 cm) |

443/8,,

(112.7 cm)

413/,_"

(105.1 cm)

48" (121.9 cm) Models

143/8"

(36.5 cm)

43w' II

(111"4cm)l_

/130 ° \ \ X

\\ 90 °

\ "]10°_'_ _. ,

477/8"

[121.6 cm)

44"

(111.8 cm I

513/8"

(130.5 cm)

_iiiii_;_¸_ii_"_;i:_!_il!ii;:i!_;ii!!i,¸¸¸¸i!;;;:ii,_i!i¸_ii:_:i_i!!!!:!!!;;i_ii:i_ooi_i_;i_iii::'_,_!;__ii:ii_ii!!_iiiii,_i!;!i_iii_,_:::_iiiiii_!!!/:J_iilili:_ii:ii_i_?_:_ii:ii':_!i;¸¸'_iCiiiiiii_i!!;i;!:,i,;,z_i_i:_;_i!_i__ii_o_!!!

The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If the refrigerator is to be installed close to the wall, see "Door Swing 90°'' on next page.

Door Swing 110 °

Actual Size

Hinge

Refrigerator to

Cabinetry Clearance

Refrigerator

Side Trim

1 1/2"

(3.8 cm)

11/4" ,

(3.2 cm)

(2.5 cm)

Cabinetry

NOTE: For Overlay Series models, rout the

hinge side of the custom door panels to a radius that is equal to at least half the

thickness of the panel if a 1300 door swing is desired. See "Adjust Doors."

NOTE: Allow 1/2" (1.3 cm) clearance between overlay

panel and cabinetry.

11/4"

(3.2 cm)',

11/2"

(3.8cm)

Panel

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

90 ° Door

Stop Position

O Hinge

Refrigerator Side Trim

(1.9 cm)

1 ii i

/2 ,,

(1.3 cm),,

, J

, ,,

i i i i i

Cabin_etr)t

Door Swing 90 °

Actual Size

Refrigerator to

Cabinetry Clearance

1 "

(2.5 cm)

3/4'

1/4"(6.35 mm)

1/2"(1.3 cm)

3/4"(1.9 cm)

1" (2.5 cm)

1/2"

(1.3 cm)

3/4'

(1.90m) i

i 1"

(2.5cm)

11/4'

Spacer Panel

Allow a minimum of 41/2'' (11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if thicker custom panels or custom handles are used. Do not overlook baseboards.

(3.2 cm)

11/2"

(3.8 cm)

OV_:i!_iiii!ii_i_i_Jii:!i'i';i,_::!_iii::i_i!i!iS_iC_/:_!ii,;i:,_::_J,_ii:_i_!7_(ii!_iiii_iii!fiii_!!i;:,_;_:iii:_;;!_li!iQi_iii:_:!!!/_i:!!' 7t'_il;17iii:_'_i;

Custom overlay panels allow you to blend the exterior of your refrigerator into the overall kitchen decor, and to use custom handles for additional design flexibility.

The custom panels must have backer panels attached in order to mount them to the refrigerator. It is most common to work with three panels, as shown in the following graphic: a decorative overlay panel, a 1/8"(3.18 mm) spacer panel or spacer strips and a 1/4"(6.35 mm) backer panel.

I Overlay Pal,el Spacer Pal,el I

Spacer Panel

1/8"

_ 1" fIIiFIIR%It n

l i I (2.54 cm) .......

_'\ _i Backer Panel

5/d'to 3/4" i i_r_

%" (B,35mm)

(3.18mrn)

i •

_ o set n rnens on

Door/Grille Trim

In some cases, your cabinet manufacturer may choose to work with one panel routed for the different dimensions. Follow these panel dimension and placement instructions to be sure that the custom overlay panels will fit properly.

IMPORTANT:

• The weight of the refrigerator door overlay panel cannot exceed 50 Ibs (23 kg).

• The weight of the freezer door overlay panel cannot exceed 40 Ibs (18.1 kg).

• The weight of the top grille overlay panel cannot exceed 10 Ibs (4.5 kg).

Tominimize panel weight, you may use 2" (5.08 cm) spacer strips around the perimeter in place of full-sheet solid spacer panels. The spacer strips must be set in at least 1" (2.54 cm) from the top, bottom and sides edges of the backer panel. If you use spacer strips, it is also recommended that you use two 2" (5.08 cm) strips horizontally centered for added support.

NOTE: For the grille and the door panels to be flush, the overlay door panel should be 1/4"(6.35 mm) thicker than the overlay grille panel.

Freezer

DoorPanel

Preferred (Dispenser)

Radius

1/2"

(1.27 cm) _E- 107/8,,_l,.t

\ (27.6 cm) I

141/4,,

(36.2 cm)

Dispenser cut-out is centered

left-to-right

337/8 ''

(86.0 cm)

Model 36 42

148/4'' (37.47 cm) 193/4'' (50.17 cm) 348/4'' (88.27 cm) 171/4'' (43.82 cm) 23V4" (59.06 cm) 408/4'' (103.51 cm) 198/4'' (50.17 cm) 263/4'' (67.95 cm) 468/4'' (118.75 cm)

71/4"

(18.4em)

Refrigerator

7 " Freezer

Door Panel

(183 era)(NDn°_lsP;ei_eler)

Decorative Overlay Panels

A B C

63/16 ''

(15.7 em)

Top Offset

_-15/8 '' (4.13 cm)

"-_ .... ," ,'r

22" i

(65.9_m) ',

...... I

• -_- ...... i i

331/4 '' I

t I

(84.6_m) ',

(--- D --}. r"

,_ I_

t Bottom Offset

1/8" (3.2 mm)

Model 36 42

D E

14V4" (36.20 cm) 19V4" (48.90 cm) 163/4'' (42.55 cm) 223/4'' (57.79 cm) 19V4" (48.90 cm) 26V4" (66.68 cm)

701/2''

(179,1 em)

--D_

Backer Panels

Bottom Offset _1 _ 1/4" (6,4 ram)

1/2" (1,27 cm)

Handle-

Side Offset

1/4"

(6.4 mm)

701/2'' (179.1 em)

•_ --E_

L Bottom Offset _"

l/s" (3.2 mm)

343/4'' (88.27 cm) 403/4'' (103.51 cm) 463/4'' (118.75 cm)

sk- eO.set

Overlay Series Door Handle Kits

Architect _ Series

The following handle styles are available. Contact your KitchenAid dealer or KitchenAid Parts and Accessories at

1-800-442-9991. In Canada, call 1-800-807-6777.

A.Architect c_Series handle (4396103) B. Flat end straight handle (4396776) with stainless

steel clamshell standoffs (4396775)

C. Round end arc handle (4396779) with bronze bullet

standoffs (4396778)

D. Round end semicircle (4396777) with stainless

steel cylinder standoffs (4396782)

Handles

These handles can be installed on side-by-side and bottom- freezer refrigerators that require overlay panels.

PART NO. DESCRIPTION

4396776 Flat End Straight - 21" (53.3 cm) Length,

Satin Stainless Steel

4396781 Flat End Straight - 45" (114.3 cm) Length,

Satin Stainless Steel

4396777 Round End Semicircle,

Satin Stainless Steel*

4396779 Round End Arc,

Satin Stainless Steel*

Handles

PART NO. COLOR

4396103 Stainless Steel

8171760 Biscuit 4396105 White 4396106 Black

All factory parts are available through your KitchenAid dealer or by calling KitchenAid Parts and Accessories at 1-800-442-9991. In Canada, call 1-800-807-6777.

Factory Door Panel Kits

Three kits containing colored acrylic or stainless steel door and top grille panels are available. Follow the kit instructions for installing the panels.

NOTE: Panel kits are not required for factory-installed stainless steel panel models.

Door Panel Part Numbers for Non-dispenser Models

Color 36 42 48

White #2325136 #2325137 #2325138

Black #2325139 #2325140 #2325141

Stainless Steel #2325142 #2325143 #2325144

Door Panel Part Numbers for Dispenser Models

Color 36 42 48

White #2325127 #2325128 #2325129

Black #2325130 #2325131 #2325132

Stainless Steel #2325133 #2325134 #2325135

*Availablefornon-dispensing models only. Standoffs

(includes screws to support 3/4"applications) These standoffs can be installed on side-by-side and bottom-

freezer refrigerators that require overlay panels. (2 standoffs must be ordered for each handle.) Handles and standoffs may be combined to meet your individual decorating needs.

PART NO. DESCRIPTION 4396775 Clamshell, Satin Stainless Steel

4396780 Clamshell, Satin Bronze 4396774 Bullet, Satin Stainless Steel 4396778 Bullet, Satin Bronze 4396782 Cylinder, Satin Stainless Steel 4396773 Cylinder, Satin Bronze

Extended Door Handle Kits

Use extended door handles when additional finger clearance is needed between the door handles and custom panel. Follow the kit instructions for installing the door handles.

Color Part Number

White #4387990

Black #8171418

Stainless Steel #4388062

Matte Aluminum #4387989

If you plan to install custom wood panels, you will need to create the panels yourself or consult a qualified cabinetmaker or carpenter. See dimension drawings for panel specifications.

IMPORTANT: Panels weighing more than recommended may cause damage to your refrigerator.

NOTE: Dimensions shown have a (+j1/16"(1.5 mm) tolerance. Panels that are more than 1/4"(6.35 mm) thick must be routed. If panels are less than 1/4"(6.35 mm) thick, install a filler panel between the doors and decorative panels.

Top Grille Panel

Door Panels for Dispenser Models

The freezer panel should not weigh more than 40 Ibs (18.1 kg). The refrigerator panel should not weigh more than 50 Ibs (23 kg).

NOTE: Dispenser cut-out is centered left-to-right.

The top grille panel should not weigh more than 10 Ibs (4.5 kg).

[ j ,',78oo,

Model A

36 341/4''(87.0 cm) 42 401/4''(102.2 cm) 48 461/4''(117.5 cm)

Door Panels for Non-dispenser Models

The freezer panel should not weigh more than 40 Ibs (18.1 kg). The refrigerator panel should not weigh more than 50 Ibs (23 kg).

107/8"

141/4''

(36.2 crn)

333/4''

(85.7 crn)

Model A B

36 141/4'' (36.2 cm) 191/4'' (48.9 cm) 42 163/4'' (42.6 cm) 223/4'' (57.8 cm) 48 191/4'' (48.9 cm) 261/4'' (66.7 cm)

Top Grille Panel - Routing Requirements

If the custom panels are thicker than 1/4"(6.35 mm), the top and bottom edges of the top panel should be edge routed 1/2"(1.3 cm) and %" (9.5 mm), respectively. Both ends should be edge routed 7/8"(2.2 cm) as shown.

707/1e''

(179 cm)

Model A

36 141/4'' (36.2 cm) 191/4'' (48.9 cm) 42 16%" (42.6 cm) 22%" (57.8 cm) 48 191/4'' (48.9 cm) 261/4'' (66.7 cm)

(6.35 ram) Top

max. -- -- Grille

(6.36ram)

341/8" (86.68 cm)

1/4"

(6.35 ram) max,

_ 1/4"

½" {

Top

(1.3._m) ]

rnln. _- /

Center face

detail between _--._._._._

offsets

1/2" __ _cm)

[._- %,,__

Bottom

Door Panels - Routing Requirements

(6.35 mm) max.

7,1

(17.8 cm)

(6.35 mm) max.

Door Panel - Side View

13_

Extended Handle - Top View

_ (6.35 mm)

j 1/4, '

(2.54 cm)

max

_/ Hinge Side

If the custom panels are thicker than 1/4"(6.35 mm), then all edges of the panels must be routed• If the standard handle is used, route the entire handle side of both panels 31/4'' (8.25 cm) to allow for finger clearance. Then route the other sides 1" (2.54 cm).

Standard Handle - Top View

31/4"

(8.26 cm)

rnln.

Hinge Side

__]

1/4"

(6.36 ram) max. I

2" (5 cm)

min.

If an extended handle kit is used, route the handle side 1/4" (6.35 mm). All other routing dimensions would remain the same

as the standard handle. Make sure your product location will allow doors with extended handles to be opened to 90 degrees. See "Door Swing Dimensions."

For more information on ordering extended handles, see "Classic Series Factory Panels and Kits."

NOTE: For both types of handles, route the top and bottom edges 1/2"(1.3 cm).

Door Panel

[

Panel Door !_,.

1 u

(2.54 cm)

1 "

(2.54 cm)

.......... ......... ............ d .....

Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning•

NOTES:

• The dimensions shown are actual product dimensions and may not reflect the needed panel installation

dimensions.

• The side panel should be a minimum of 1/_,,(1.27 cm) thick to avoid warping.

• If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on rear wall.

Refrigerator

241/s.

(61,3 cm)

(60,3 cm)

231/2 ''

(59,7 crn)

2311/1e"

SideTrim

1/4"

(6.35 mm)

11/64"

(4,5 turn)

3/16"

(4.7 mrn)

7/32"

(5.5 mm)

1%2"(10ram)

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add %2" (5.6 mm) to this measurement to allow the side panel to fit into the trim.

2. If the panel is more than 1/4"(6.35 mm) thick, route the front edge to allow the side panel to fit into the trim.

(15.7ram)

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

• The dimensions shown are actual product dimensions and may not reflect the needed installation dimensions.

• The side panel should be a minimum of 1/2"(1.27 cm) thick to avoid warping.

• If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on rear wall.

Refrigerator

Overlay

2311/1_,'

(60,16 cm)

Flush Installation Dimensions

1. Measure the distance from point A (as shown) to the back wall.

2. Attach the support board with a screw or adhesive that is compatible with aluminum and wood.

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back wall.

2. Route the front edge of the support board or attach a 1/4" (6.35 mm) board to hold the panel in the cabinet side trim.

Side Trim

3/8"

(9.7 ram)

1/16" _l

(1,5 mm) v I

3/32" _ !

(2.38 mm) _-_

3/16 _'

(4.5 ram)

Inset Installation Dimensions

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add ½2" (0.8 mm) to this measurement to allow the side panel to fit into the trim.

2. If the panel is more than 3/8"(9.5 mm) thick, route the front edge to allow the side panel to fit into the trim.

INSTALLATION INSTRUCTIONS

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

1. Measure the distance from point A (as shown) to back wall.

2. Route the front edge of the support board or attach a %" (9.5 mm) board to hold the panel in the cabinet side trim.

Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See "Tipping Radius" in the "Installation Requirements" section for

more information. If you do not have adequate ceiling height to stand the

refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart).

Model Reduced Tipping Radius

36 88" (223.5 cm) 42 881/2'' (224.8 cm) 48 891/4'' (226.7 cm)

f. Grasp both ends of the top grille.

2. Push the top grille straight up; then pull straight out. Lay the grille on a soft surface.

IMPORTANT:

• Do not remove the protective film until the refrigerator is in its operating position.

• All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator.

• Keep the cardboard shipping piece or plywood under the refrigerator until it is installed in the operating position.

Remove and save the literature package bag taped to the side of the refrigerator and the parts bag behind the grille. Remove the four brackets (two on each side) that attach the shipping base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the refrigerator is in its final position.

If necessary, reduce the tipping radius. See "Tipping Radius" for ceiling height requirements or "Reduce Tipping Radius" for step-by-step instructions. Ifyou do not need to reduce the tipping radius, proceed to "Move the Refrigerator into

House."

A. Top grille B. Cabinet side trim

Remove the six screws attaching each cabinet side trim to the refrigerator and remove the side trims.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

1. Place an appliance dolly under the left side of the refrigerator as shown. Be sure to protect the side trims and handles. Place the corner posts from the packing materials over the trims and handles as appropriate. Slowly tighten the strap.

NOTE: Pass the dolly strap under the handles for the Architect _ Series.

IMPORTANT:

To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

• It is recommended that board(s) be installed before the refrigerator is installed.

• Board(s) must be long enough to fully cover the width of the compressor cover.

• Locate the board(s) so the bottom surface(s) of the board(s) is(are) 84" (213 cm) from the floor.

During installation, raise the refrigerator up so there is 1/4" (6.35 mm) maximum between the top of the refrigerator and the bottom of the anti-tip board(s). Do not crush the compressor cover when raising the rear leveling legs.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall 80" to 90" (203 cm to 229 cm) above floor.

2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards to wall studs behind refrigerator. Use six #8 x 3" (7.6 cm) (or longer) wood screws. The wood screws must be screwed into the studs at least 11/2"(3.8 cm). The board(s) must overlap the compressor cover.

A B

2. Place pieces of the shipping carton on the floor when rolling the dolly and refrigerator into the house. Move the refrigerator close to the built-in opening.

3. Place top of cardboard carton or plywood under refrigerator.

4. Stand the refrigerator up. First, place the left bottom edge of the refrigerator on the floor, stand the refrigerator upright and then lower the right-hand side of the refrigerator to the floor.

5. Do not remove protective film or cover.

6. Reassemble the trim and top grille after the dolly has been removed from the refrigerator.

2" (5 cm)

A. Centerboard ¼" (6.35 mm) max. above refrigerator B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

C.Attach to studs with six #8 x 3" (7.6 cm) screws O. Compressor cover

Read all directions before you begin. IMPORTANT: Ifyou turn the refrigerator on before the water line

is connected, turn the ice maker OFR

Style I - Shutoff Valve Connection

NOTE: If your water line connection does not look like Style 1, see "Style 2 - Copper Line Connection."

1. Unplug refrigerator or disconnect power supply. IMPORTANT: Before attaching the tubing to shutoff valve, flush

the main water supply line to remove particles and air inthe water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

2. Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.

3. Thread the provided nut onto the shutoff valve as shown.

J/ |

A B

A.Bulb B.Nut

C. Water tubing

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

6. Plug in the refrigerator or reconnect power.

7. Flush the water system. See "Water System Preparation."

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

Style 2 - Copper Line Connection

Connecting to Water Line NOTE: If existing water line meets the "Water System

Requirements," see "Connecting to Refrigerator."

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2"to 11/4'' (1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold water pipe you have selected.

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4"(6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten, or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten the clamp or the sleeve. This will crush the copper tubing.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air inthe water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

8. Turn off the shutoff valve on the water pipe. Coil the copper tubing.

9. Check for leaks around the saddle valve.

Connecting to Refrigerator

1. Unplug the refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.

3. Measure the distance from the shutoff valve to the opening in which the refrigerator will be located. Tubing must be extended from the shutoff valve into the refrigerator opening following specific guidelines. See "Water Supply Requirements."

4. A 1/4"x 1/4"(6.35 mm to 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

A B

A. Water tubing

B.Nut

C. Bulb D. Coupling (purchased)

5. Turn shutoff valve ON.

Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

7. Plug in the refrigerator or reconnect power.

8. Flush the water system. See "Water System Preparation."

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

E.Ferrule(purchased) F. Nut (purchased)

G.Household water line(as

connected inprevious section)

A. Cold water pipe B. Pipe clamp C. Copper tubing D. Compression nut

e ....

E D

E. Compression sleeve F. Shutoff valve

G. Packing nut

! ,_:!w,i::!_iiiiii_ii!_!_!_!_:_;::!!,_!!!_i!ii;iU_iiii:;iii:_i?iiiii!!_:i_i!,ii_!!_i_i_:_i!ito!_i_¸_

Emectrical Shock Hazard

Pmuginto a grounded 3 prong outieto Do not remove ground prong. Do not use an adapter.

Do not use an extension cord° Failure to follow these }nstructions can resumt }n death,

fire, or electrical shock.

f. Set control switch at top of cabinet to the OFF position.

2. Plug into a grounded 3 prong outlet.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: All four leveling legs must contact the floor to support and stabilize the full weight of refrigerator. Rollers are for moving refrigerator and not for permanent support.

After moving the refrigerator to its final location:

1. Use a %6" socket driver to turn the leveling bolts clockwise to extend the legs to the floor as shown. The rollers should be

off the floor.

_................................B

A. Rear leveling bolt B. Front leveling bolt

Adjust the leveling legs to level and align the refrigerator from left to right and front to back so that the refrigerator is level and aligned with the cabinetry. The cabinetry surface must be plumb for the ideal fit of the refrigerator side trim.

IMPORTANT: To avoid floor damage, make sure levelers are raised (not touching floor) and refrigerator is on rollers before moving.

1. Place top of cardboard carton or plywood under refrigerator. Remove dolly.

2. Do not remove protective film or cover.

3. Move the refrigerator straight back and evenly into the opening. Be sure that the refrigerator side trims are not interfering with the door opening. Also, be sure that the water tubing is not kinked and the power supply cord is on top of the refrigerator.

Continue adjusting all of the leveling legs to raise the refrigerator until the top is within at least 1" (2.54 cm) of the top soffit,

NOTE: If an anti-tip board has been used, adjust the leveling legs until the top of the refrigerator is within 1/4"(6.35 mm) of the bottom of the anti-tip board as shown. Do not crush the

compressor cover.

If needed, route the door panels or install a filler panel between the doors and the decorative panels. See the

"Classic Series Custom Panels" section in "Installation Requirements."

" (6

mm)

2" (5 cm)

A. Center board ¼" (6.35 mm) max. above refrigerator B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards C. Attach to studs with six #8 x 3" (7.6 cm) screws O. Compressor cover

•

IMPORTANT: Adjust in small increments to keep from damaging the cabinet trim and causing problems with the door alignment or top grille fit. To avoid damage to the cabinet or leveling legs, do not apply more than 50 inch- pounds (5.65 Nm) of torque to the leveling bolts. The leveling legs can be extended to a maximum of 11/4'' (3.18 cm) below

the rollers.

For Classic and Overlay models, additional adjustments may be needed after the custom panels are installed.

A ......

IIIIIIIIIIIIltlllltllllllllllllllttllilllllllllllllllltlilllll

A. Panels

5. Replace the door handles. Install the top screw on each handle first, Be sure that the top of both door handles are aligned,

6. If the door handles are not aligned, loosen all handle screws and adjust door handles up or down, Tighten the screws.

7. Check refrigerator level and adjustment. Adjust if needed.

Top Grille Panel

1. Grasp both ends of the top grille.

2. Push straight up, then pull straight out, Place the top grille panel-side down on a soft working surface.

B A B

IMPORTANT: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service.

Door Panels

1. Remove all tape and door bracing from the refrigerator and freezer doors.

2. Remove the screws that attach the handles to the door frame.

3. Slide the decorative door panels into the door frames.

A. Top grille

B. Cabinet side trim

Remove one end cap by loosening the nuts and sliding off the end cap,

A. Bottom rail C. End cap B. Nuts D. Top rail

4. Slide the backer panel into the top grille channel and reattach the end cap.

A. Backer panel

Replace the top grille in the cabinet side trims and pull the panel down slightly to lock it into place.

Door Panel Installation

1. Remove all tape and door bracing from the refrigerator and freezer doors.

2. Open the refrigerator and freezer compartment doors.

3. Remove the handle side and top trims.

................._ a

IIItlIIIIIIIIIIIIIIItlUtlIIIIIIIIIIItlUtlIIIIIIIIIIttlUtlII

A. Top grille B. Cabinet side trim

IMPORTANT:

• Install the custom handles prior to installing the panels on the refrigerator. For more information on KitchenAid custom handle selection, refer to the KitchenAid Catalog, visit

www.kitchenaid.com, or call 1-800-442-9991. In Canada,

visit www.KitchenAid.ca, or call 1-800-807-6777.

• Create custom door overlay panels according to the specifications in the "Overlay Series Custom Panels" section.

• KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to

the refrigerator for service.

A. Trims

Slide the custom panels into the bottom and hinge side trims on the refrigerator compartment and freezer compartment doors, making sure that the backer panel fits into the hinge

side trims.

..........A

IIIIIIIIIttlUtlIIIIIIIIIIIIIttlUtlIIIIIIIIIIIIIIIIIIIItlIIII

A. Panels

5. Reinstall the handle-side and top trims.

6. Remove the protective skin from the screw covers. Slide or snap the screw covers into the handle trim section.

7. Check refrigerator level and alignment. Adjust if needed.

+ 53 hidden pages