KitchenAid KSSS48FMX03, KSSS42QMW03, KSSS42FMX03, KSSO48QMB03, KSSO42QMB03 Installation Guide

...

®itchen_kid ®

SIDE BY SIDE BUILT-IN REFRIGERATOR

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.

REFRIGERADOR EMPOTRADO

DE DOS PUERTAS

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACION REQUIERE DE 20 MAS PERSONAS.

REFRIGERATEUR ENCASTRE COTE A COTE

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L'INSTALLATION N¢:CESSITE L'INTERVENTION DE 2 PERSONNES OU PLUS.

Table of Contents/Indice/Table des matieres .................................................................. 2

2317872A

TABLEOF CONTENTS

REFRIGERATOR SAFETY ............................................................. 3

MODELS .......................................................................................... 4

INSTALLATION REQUIREMENTS ................................................ 6

Tools and Parts ............................................................................ 6

Location Requirements ................................................................ 6

Electrical Requirements ............................................................... 7

Water Supply Requirements ........................................................ 8

Tipping Radius ............................................................................. 8

Product Dimensions ..................................................................... 9

Door Swing Dimensions ............................................................. 10

Overlay Series Door Panel & Cabinetry Clearance .................... 11

Overlay Series Custom Panels and Handle Kits ....................... 13

Classic Series Factory Panels and Kits ..................................... 14

Classic Series Custom Panels ................................................... 15

Classic, Architect ®and Pro Line®Series Custom Side Panels. 16

Overlay Series Custom Side Panels .......................................... 17

INDICE

SEGURIDAD DEL REFRIGERADOR ........................................... 27

MODELOS ..................................................................................... 28

REQUlSITOS DE INSTALACION ................................................. 30

Piezas y Herramientas ............................................................... 30

Requisites de ubicaci6n ............................................................. 30

Requisites electricos .................................................................. 31

Requisitos del suministro de agua ............................................. 32

Arco de vuelco ........................................................................... 32

Medidas del producto ................................................................ 33

Medidas de oscilacidn de las puertas ....................................... 34

Espacio para el panel de la puerta de

la serie Overlay y para los gabinetes ......................................... 35

Paneles a la medida y juegos de agarraderas de

la serie Overlay ........................................................................... 37

Paneles y juegos de fabrica de la serie Classic ........................ 38

Paneles a la medida para la serie Classic ................................. 39

Paneles laterales a la medida para las

series Classic, Architect ®y Pro Line®......................................... 41

Paneles laterales a la medida para la serie Overlay .................. 42

INSTALLATION INSTRUCTIONS ................................................ 18

Unpack the Refrigerator ............................................................. 18

Reduce Tipping Radius .............................................................. 18

Move the Refrigerator into House .............................................. 19

Install Anti-Tip Boards ................................................................ 20

Connect the Water Supply ......................................................... 20

Plug in Refrigerator ..................................................................... 21

Move Refrigerator to Final Location ........................................... 21

Level and Align Refrigerator ....................................................... 22

Install Classic Series Custom Panels ......................................... 22

Install Overlay Series Custom Panels ........................................ 23

Adjust Doors ............................................................................... 24

Install Side Panel ........................................................................ 25

Install Base Grille ........................................................................ 25

Complete Installation .................................................................. 26

Water System Preparation ......................................................... 26

INSTRUCCIONES DE INSTALACION ......................................... 43

Desempaque el refrigerador ...................................................... 43

C6mo reducir el arco de vuelco ................................................. 43

Cdmo hacer entrar el refrigerador en la casa ............................ 44

Crime instalar los tableros antivuelco ........................................ 44

Conexidn del suministro de agua .............................................. 45

Cdmo enchufar el refrigerador ................................................... 46

C6mo mover el refrigerador a su ubicaci6n final ....................... 46

Nivelaci6n y alineamiento del refrigerador ................................. 47

Cdmo instalar los paneles a la medida para la serie Classic ....47

Cdmo instalar los paneles a la medida para la serie Overlay....48

Ajuste las puertas ....................................................................... 49

Cdmo instalar el panel lateral ..................................................... 50

Cdmo instalar la rejilla de la base .............................................. 50

Crime terminar la instalacidn ..................................................... 51

Preparaci6n del sistema de agua .............................................. 51

TABLE DES MATIERES

S¢:CURIT¢: DU RC:FRIGC:RATEUR .............................................. 52

MODELES ..................................................................................... 53

INSTRUCTIONS D'INSTALLATION ............................................ 55

Outillage et pieces ...................................................................... 55

Exigences d'emplacement ......................................................... 55

Specifications electriques ......................................................... 56

Specifications de I'alimentation en eau ..................................... 57

Rayon de basculement .............................................................. 57

Dimensions du produit ............................................................... 58

Dimensions pour le pivotement des pores ............................... 59

Serie Overlay - Panneau de porte et placard -

dimensions et espace libre ........................................................ 60

Panneaux personnalises et poignees de la serie Overlay ......... 62

Ensembles de panneaux d'origine de la serie Classic .............. 63

Panneaux personnalises de la Serie Classic ............................. 64

Panneaux lateraux personnalises des

Series Classic, Architect _et Pro Line®....................................... 66

Panneaux lateraux personnalises de la Serie Overlay .............. 66

INSTRUCTIONS D'INSTALLATION ............................................. 67

Deballage du refrigerateur .......................................................... 67

R_duction du rayon de basculement ......................................... 68

Faire entrer le refrigerateur dans le domicile ............................. 68

Installation de planches antibasculement .................................. 69

Raccordement a la canalisation d'eau ....................................... 69

Brancher le rdrigerateur ............................................................. 71

Deplacement du r6frig_rateur a I'emplacement final ................. 71

Reglage de I'aplomb et alignement du refrigerateur ................. 71

Installation des panneaux personnalises de la Serie Classic....72

Installation des panneaux personnalises de la Serie Overlay ...73

Ajustement des portes ............................................................... 74

Installation du panneau lateral ................................................... 75

Installation de la grille de la base ............................................... 75

Achever I'installation .................................................................. 76

Preparation du systeme d'eau ................................................... 76

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

Side by Side Non-Dispensing Refrigerators

MODELS

Architect ®Series Features wraparound styling that complements the contoured

door handles. This series provides a warm commercial-looking built-in refrigerator.

KSSC36FMS KSSC42FMS KSSC48FMS

Classic Series

Features factory-installed, traditional style trim to provide a "framed" look. This series requires the installation of custom panels that are not included,

KSSS36FMX KSSS42FMX KSSS48FMX

Overlay Series

Features factory-installed, overlay style trim to provide a "frameless" look. This series requires the installation of custom panels, handles, and standoffs.

KSSO36FMX KSSO42FMX KSSO48FMX

Pro Line®Series Features extraordinary design and exceptional levels of

performance. This series is a perfect blend of form and function delivering professional quality, durability and simplicity.

KSSV42FMS KSSV42FMM

Models - Side by Side Dispensing Refrigerators

t_ ,¸ i -,- J

Architect ®Series

Features wraparound styling that complements the contoured door handles. This series provides a warm commercial-looking built-in refrigerator.

KSSC36QMS KSSC42QMS KSSC48QMS

!ll!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!n_i

Classic Series

Features factory-installed, traditional style trim to provide a "framed" look. This series requires the installation of custom panels that are not included.

KSSS36QMB KSSS42QMB KSSS48QMB KSSS36QMW KSSS42QMW KSSS48QMW KSSS36QMX KSSS42QMX KSSS48QMX

Overlay Series

Features factory-installed, overlay style trim to provide a "frameless" look. This series requires the installation of custom panels, handles, and standoffs.

KSSO36QMB KSSO42QMB KSSO48QMB

Complete Series

Features factory-installed stainless steel trim and panels to create a sleek, contemporary look.

KSSP36QMS KSSP42QMS KSSP48QMS

INSTALLATION REQUIREMENTS

IMPORTANT:

• Installer: Leave Installation Instructions with the homeowner.

• Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local

electrical inspector's use.

TOOLS NEEDED: Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed here.

• Torx_tT27 screwdriverHand drill or electric drill

(properly grounded) Drill bits

Two adjustable wrenches

• Phillips screwdriver

• Small level

• Appliance dolly

PARTS NEEDED:

Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed) One or two 2" x 4" x 32" (5 cm x 10cm x 81 cm) wood board(s) Order factory panels, make custom panels or consult a

qualified cabinetmaker or carpenter to make the panels. Overlay Series: Make custom panels, or consult a qualified

cabinetmaker or carpenter to make the panels. See "Installation Requirements" for more information.

Architect _ and Pro Line ®Series are shipped complete. If you are connecting the water line directly to copper tubing

and not to a shutoff valve, you need a ferrule, a union, and a W' (6.35 mm) compression fitting.

• _/32"nut driver

• %" and W' open-end wrenches

• %2" Allen wrench

• Y4"and %6" socket drivers

• Tape measure

<{a i<£ <}%t:Y_LI!Ii_':}ei%t£S

The refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to enclose the refrigerator.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT:

• Observe all governing codes and ordinances.

• It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source.

• Do not install in a location where the temperature will fall below 55°F (13°C).

• Floor must support the refrigerator weight, more than 600 Ibs (272 kg), door panels and contents of the refrigerator.

• Ceiling height must allow for side tipping radius. See "Tipping Radius."

• Location should permit doors to open fully. See "Door Swing Dimensions."

• Location must permit top grille removal. See "Opening Dimensions."

Opening Dimensions

t®TORX is a registered trademark of Textron Innovations Inc.

To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the rear wall studs 80" to 90" (203 cm to 229 cm) above the floor. See "Install Anti-Tip Boards" for more information.

NOTE: A clearance of W' (1.3 cm) must be maintained above the top grille in order for the top grille to be removed.

A grounded 3 prong electrical outlet should be placed within 4" (10.2 cm) of the right side cabinets or end panel. See "Electrical Requirements" for more information.

The water shutoff should be located in the base cabinet on either side of the refrigerator or some other easily accessible

area. If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor or the back wall. See "Water Supply Requirements" for more

information.

;31/2"(212.1 cm) min. 843/4'' (215 cm) max. to bottom of solid soffit

77"

(196 cm)

Width

(see chart following)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. IMPORTANT: Ifthis product is connected to a GFCI (Ground

Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, remove the top grille and turn the master power switch to OFF or disconnect power at the circuit breaker

box. When you are finished, turn ON the master power switch or

reconnect power at the circuit breaker box. Then reset the control to the desired setting.

(2.54 cm)

24"

(60.96 cm) min,

Model Width A (as shown above)

36 351/2''(90.2 cm) to 353/4'' (90.8 cm) 42 411/2"(105.4 cm) to 413/4"(106.1 cm) 48 471/2''(120.7 cm) to 473/4'' (121.3 cm)

NOTE: Flooring under refrigerator must be at same level as the room. Face of cabinetry must be plumb.

Allinstallationsmustmeetlocalplumbingcoderequirements. Thewatershutoffshouldbelocatedinthebasecabineton

eithersideoftherefrigeratororsomeothereasilyaccessible area.Theright-handsideisrecommended.Theaccesshole throughthecabinetmustbewithin_A"(12.7mm)oftherear

wall. NOTE:Ifthewatershutoffvalveisinthebackwallbehind

therefrigerator,itmustbeatananglesothatthetubeisnot kinkedwhentherefrigeratorispushedintoitsfinalposition.

Ifthewaterpressuretothereverseosmosissystemislessthan 40to60psi(276to414kPa):

• Checktoseewhetherthesedimentfilterinthereverse osmosissystemisblocked.Replacethefilterifnecessary.

• Allowthestoragetankonthereverseosmosissystemtorefill afterheavyusage.

• Ifyourrefrigeratorhasawaterfiltercartridge,itmayfurther reducethewaterpressurewhenusedinconjunctionwitha reverseosmosissystem.Removethewaterfiltercartridge.

Ifyouhavequestionsaboutyourwaterpressure,callalicensed, qualifiedplumber.

Be sure there is adequate ceiling height to stand the refrigerator upright when it is moved into place.

• The dolly wheel height must be added to the tipping radius when a dolly is used.

• If needed, the tipping radius can be reduced. See "Reduce Tipping Radius."

Side Tipping Radius

(2.54 cm)

24"

(60.96 cm) min,

If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor. A _/2"(12.7 mm) hole for plumbing should be drilled at least 6" (15.2 cm) from the right or left hand side cabinet or panel. On the floor, the hole should be no more than 1" (2.54 cm) away from the back wall. See "Connect the Water Supply."

• If additional tubing is needed, use copper tubing and check for leaks. Install the copper tubing only in areas where the household temperatures will remain above freezing.

• Do not use a piercing-type or 3/_6"(4.76 mm) saddle valve which reduces water flow and clogs more easily.

NOTE: Your refrigerator dealer has a kit available with a _/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

The side tipping radius varies depending upon the width of the model. Use the chart provided to determine the side tipping

radius. NOTE: Tip on side only.

I I

Model Tipping Radius A

36 901/2'' (229.9 cm) 42 93" (236.2 cm) 48 96" (243.8 cm)

Side View

Front View

• The depth from the front of the top grille to the back of the refrigerator cabinet is 25%" (64.5 cm).

• The power cord is 84" (213 cm) long.

• The water line attached to the back of the refrigerator is 5 ft (1.5 m)long.

• Height dimensions are shown with leveling legs extended W' (3 mm) below the rollers.

-- -- "_-_(64.5 cm)

*83%"

(211.8 cm)

253/8''

231/2''

(59.7 cm) _

84" (213.4 cm) Power Cord

• Width dimensions were measured from trim edge to trim edge.

• Height dimensions are shown with leveling legs extended W' (3 mm) below the rollers.

(211.8 cm)

¢L_ _ mm

"31/2" (8.9 cm)

°-r

*When leveling legs are fully extended to 1//4" (3.2 cm) below

rollers, add 1V8"(2.9 cm) to the height dimensions.

Top View *When leveling legs are fully extended to 1W' (3.2 cm) below

rollers, add 1%" (2.9 cm) to the height dimensions.

Model Width A (Trim edge to trim edge)

36 36%" (92.1 cm) 42 42W' (107.3 cm) 48 48W' (122.6 cm)

(seechart following)

253/8" (64.5 cm)

_L_

Model WidthA

36 35V4" (89.5 cm) 42 41_/4"(104.8 cm) 48 47W' (120 cm)

Thelocationmustpermitbothdoorstoopentoaminimumof 90°.Allow41/2''(11.4cm)minimumspacebetweenthesideofthe refrigeratorandacornerwall.

NOTE:Moreclearancemayberequiredifyouareusingoverlay panels,customhandles,orextendedhandlesonaClassic

model. Toadjustthedoorswing,see"AdjustDoors."

36" (91.4 cm) Model

141/2"

(37 cm)

/3ov+,, 4o"/

/(o24) (lO2cm)/

/ I I_ (-193/4"--_ I /

/i I (50°°)

38v_"I I I 431/_,,

(98crn) _ 1(110cm)

42" (106.7 cm) Models

II _ jg_,_ X

X :110°```_. _ ,

13o+-_.z i" 'L

193/4"

(50 cm)

l,10L

43[/+,,<--"

(110 cm)l _

45%"

(115 cm)

(68 cm)

<-- 263/4" _ 501/2 ''

(128 cm)

For Overlay series models KSSO36FMX, KSSO42FMX, KSSO48FMX, KSSO36QMB, KSSO42QMB, KSSO48QMB and KBR(L)O36FMX. The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If

the refrigerator is to be installed close to the wall, see "Door Swing 90°" on next page.

Door Swing 110

Actual Size

Refrigerator to

)

Refrigerator

Side Trim

Cabinetry Clearance

_ S 110 ° Door

top Position ...........O

Hinge

(2.5 cm)

Cabinetry

I 1/2"

(3.8 cm)

11//, ,

(3.2 cm)

; V4" (6.35 mm)

1/£,,(1.3 cm)

s/4"(1.9 cm)

1" (2.5 cm)

NOTE: Allow W' (1.3 cm) clearance between overlay

panel and cabinetry.

NOTE: For Overlay Series models, rout the hinge side of the custom door panels to a

radius that is equal to at least half the thickness of the panel if a 130° door swing is

desired. See "Adjust Doors."

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

Panel

90 ° Door

Stop Position

O Hinge

Refrigerator

Side Trim

(1.9cm)

1 i] i

/2 ,,

(1.3 cm),,

i i i i i i

Cabin:etr

Door Swing 90 ° Actual Size

Refrigerator to Cabinetry Clearance

(2.5 cm)

3/4"

1/4"(6.35 mm)

1/2"(1.3 cm)

.............. 3/4"(1.9 cm)

___.J.

1" (2.5 cm)

1/2"

(1.3 cm)

3/4"

(1.9cm)i

I 1"

(2.5cm)

1 1/4"

(3.2 cm)

11/2''

(3.8cm)

-- _

Spacer Panel

Allow a minimum of 41/2'' (11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if thicker custom panels or custom handles are used. Do not overlook baseboards.

_%_ ......... __, _..,. C_ _ ,_ _,,, S _ _ ..... :" ...... ....... _ " _%...... " _ " _t .....

.... j ......

For Overlay series models KSSO36FMX, KSSO42FMX, KSSO48FMX, KSSO36QMB, KSSO42QMB, KSSO48QMB and KBR(L)O36FMX. Custom overlay panels allow you to blend the exterior of your

refrigerator into the overall kitchen decor, and to use custom handles for additional design flexibility.

The custom panels must have backer panels attached in order to mount them to the refrigerator. It is most common to work with three panels, as shown in the following graphic: a decorative overlay panel, a Vs" (3.18 mm) spacer panel or spacer strips and a V4" (6.35 mm) backer panel.

Panel

Overlay

I Spacer Panel

Spacer Panel r_

IMPORTANT:

• The weight of the refrigerator door overlay panel cannot exceed 50 Ibs (23 kg).

The weight of the freezer door overlay panel cannot exceed 30 Ibs (13.5 kg).

The weight of the top grille overlay panel cannot exceed 10 Ibs (4.5 kg).

Tominimize panel weight, you may use 2" (5.08 cm) spacer strips around the perimeter in place of full-sheet solid spacer panels. The spacer strips must be set in at least 1" (2.54 cm) from the top, bottom and sides edges of the backer panel. If you use spacer strips, it is also recommended that you use two 2"

1/8"

(5.08 cm) strips horizontally centered for added support. NOTE: For the grille and the door panels to be flush, the overlay

I I1_ r. mir_irTlu[T}

I (2.54 cm) j ......

II _D_)r/Gdlle Trim

_ Offset Dimension

In some cases, your cabinet manufacturer may choose to work

door panel should be W' (6.35 mm) thicker than the overlay grille panel.

Top Grille

73/8" C >

I (1 8.73 cm)

with one panel routed for the different dimensions. Follow these panel dimension and placement instructions to be sure that the custom overlay panels will fit properly.

s,.,,Tr- ..... F

(21.59cm)__ _ = - -_.= =

Bottom Offset 1" (2.54 cm)

473Ae''

(119,86 cm)

Freezer

Framed Dispenser

-_--- A ---_

-}....

! 7

! (59.53 cm)

343/8"

(87,3 cm)

__{__t_

Handle-Side

_- Offset

Vs" (3.2 ram)

71V16"

(180.50 cm) l

24"

(60,96 cm)

343/4 ''

(88,27 cm)

FreezerFrameless

Dispenser

237/16" i Handle-Side (59.53 cm) i Offset

Vs" (3.2 mm)

_ Bottom Offset

1/8" (3,2 mm)

," .... ;"

343/8" _ Offset (87,3 cm) i Vs" (3,2 mm)

Handle-Side

Freezer

Non-Dispenser

<---A _1

701/2"

(179.07 cm)

_(--- D _

Handle-Side

Offset --_

l/s" (3.2 mm)

711/16''

(180.50 cm)

Refrigerator

B -]_"-

,"k

I I I I

701/2'' (179.07 cm)

L,____

:_2! ..... i_....

Model

36 42

Bottom Offset Bottom Offset

Vs" (3.2 ram) 1/8" (3,2 ram)

Decorative Overlay Panels

A B C Model

14%" (37.15 cm) 19%" (49.85 cm) 34W' (87.63 cm) 36 17%" (43.50 cm) 23%" (58.74 cm) 40W' (102.87 cm) 42

19%" (49.85 cm) 26%" (67.63 cm) 46W' (118.11 cm) 48

Bottom Offset

1/8" (3,2 ram)

Backer Panels

D E

147Ae'' (36.67 cm) 197Ae"(49.37 cm) 16_¾e''(43.50 cm) 22_%e'' (58.26 cm)

197Ae"(49.37 cm) 267Ae"(67.15 cm)

Bottom Offset

1/s" (3,2 mm)

34W' (87.63 cm) 4OW' (102.87cm)

46W' (118.11 cm)

Overlay Series Door Handle Kits

Architect _ Series

The following handle styles are available. Contact your KitchenAid dealer or KitchenAid Parts and Assessories at

1- 800- 442-9991. In Canada, call 1-800-807-6777.

A.Architect _ Series handle (4396103) B. Flat end straight handle (4396776) with stainless

steel clamshell standoffs (4396775)

C. Round end arc handle (4396779) with bronze bullet

standoffs (4396778)

D. Round end semicircle (4396777) with stainless

steel cylinder standoffs (4396782)

Handles

These handles can be installed on side-by-side and bottom- freezer refrigerators that require overlay panels.

PART NO. DESCRIPTION

4396776

Satin Stainless Steel

4396781 Flat End Straight - 45" Length,

Satin Stainless Steel

4396777 Round End Semicircle,

Satin Stainless Steel*

Handles

PART NO. COLOR

4396103 Stainless Steel 8171760 Biscuit 4396105 White 4396106 Black

For Classic Series models: KSSS36FMX, KSSS42FMX, KSSS48FMX, KSSS36QMB, KSSS42QMB, KSSS48QMB, KSSS36QMW, KSSS42QMW, KSSS48QMW, KSSS36QMX, KSSS42QMX, and KSSS48QMX.

All factory parts are available through your KitchenAid dealer or by calling KitchenAid Parts and Accessories at 1-800-442-9991. In Canada, call 1-800-807-6777.

Factory Door Panel Kits

Three kits containing colored acrylic or stainless steel door and top grille panels are available. Follow the kit instructions for installing the panels.

NOTE: Panel kits are not required for factory-installed stainless steel panel models.

Door Panel Part Numbers for Non-dispenser Models

Color 36 42 48

White #2220852 #2220853 #2220854

Black #2220855 #2220856 #2220857

Stainless #2220861 #2220862 #2220863 Steel

4396779 Round End Arc,

Satin Stainless Steel*

*Availablefor non-dispensing models only.

Standoffs

(includes screws to support 3/4"applications) These standoffs can be installed on side-by-side and bottom-

freezer refrigerators that require overlay panels. (2 standoffs must be ordered for each handle.) Handles and standoffs may be combined to meet your individual decorating needs.

PART NO. DESCRIPTION

4396775 Clamshell, Satin Stainless Steel 4396780 Clamshell, Satin Bronze 4396774 Bullet, Satin Stainless Steel 4396778 Bullet, Satin Bronze 4396782 Cylinder, Satin Stainless Steel 4396773 Cylinder, Satin Bronze

Door Panel Part Numbers for Dispenser Models

Color 36 42 48

White #2220864 #2220865 #2220866

Black #2220867 #2220868 #2220869

Stainless #2220873 #2220874 #2220875 Steel

Extended Door Handle Kits

Use extended door handles when additional finger clearance is needed between the door handles and custom panel. Follow the kit instructions for installing the door handles.

Color Part Number

White #4387990 Black #8171418 Stainless Steel #4388062 Matte Aluminum #4387989

For Classic Series models: KSSS36FMX, KSSS42FMX, KSSS48FMX, KSSS36QMB, KSSS42QMB, KSSS48QMB,

KSSS36QMW, KSSS42QMW, KSSS48QMW, KSSS36QMX, KSSS42QMX, and KSSS48QMX.

If you plan to install custom wood panels, you will need to create the panels yourself or consult a qualified cabinetmaker or carpenter. See dimension drawings for panel specifications.

IMPORTANT" Panels weighing more than recommended may cause damage to your refrigerator.

NOTE: Dimensions shown have a (+_)1/16"(1.5 mm) tolerance. Panels that are more than 1/4"(6.35 mm) thick must be routed. If panels are less than 1/4"(6.35 mm) thick, install a filler panel between the doors and decorative panels.

Top Grille Panel

The top panel should not weigh more than 10 Ibs (4.5 kg).

Door Panels for Dispenser Models

The two freezer panels combined should not weigh more than 30 Ibs (13.5 kg). The refrigerator panel should not weigh more than 50 Ibs (23 kg).

B-_ I

237/1e''

59,5 cm)

707/16"

(179 cm)

[

Model A 36

42 48

Door Panels for Non-dispenser Models

The freezer panel should not weigh more than 30 Ibs (13.5 kg). The refrigerator panel should not weigh more than 50 Ibs (23 kg).

•_: A_ '_ B -_

35%" (89.5 cm) 41%" (105 cm) 47%" (120 cm)

_(184 mm)

347/16''

87.4 cm)

Model A B

36 141/4'' (36.2 cm) 191/4'' (48.9 cm) 42 163/4'' (42.6 cm) 223/4'' (57.8 cm) 48 191/4'' (48.9 cm) 261/4'' (66.7 cm)

Top Grille Panel - Routing Requirements

If the custom panels are thicker than 1/4"(6.35 mm), the top and bottom edges of the top panel should be edge routed 1/2"(1.3 cm) and %" (9.5 mm), respectively. Both ends should be edge routed %" (2.2 cm) as shown.

v,,,TI I ITv,,,(6,35 ram) (6.35 mm)

Model A B

36 141/4'' (36.2 cm) 191/4'' (48.9 cm) 42 163/4'' (42.6 cm) 22%" (57.8 cm) 48 191/4'' (48.9 cm) 261/4'' (66.7 cm)

max. _ Top Top _ max.

Grille Grille

(2.2 cm) (2.2 cm)

NOTE: When creating a panel with face detail, the offsets will be hidden and must be accounted for in order to center the detail in

the top grille.

_[_ 1/4"

(6.35 mm) max.

1/2" Top

(1.3 cm)

Center face

detail between _/--,__

(9.5mm)

--j-

min.

offsets

3/8" ]

min. Bottom

Door Panel - Side View

Extended Handle - Top View

_ (6.35 mm)

i 1/4, '

(2.54 cm)

max

Hinge Side

_ _-- I/4''

Door Panels - Routing Requirements

If the custom panels are thicker than 1/4"(6.35 mm), then all edges of the panels must be routed. If the standard handle is used, route the entire handle side of both panels 3W' (8.25 cm) to allow for finger clearance. Then route the other sides 1" (2.54 cm).

Standard Handle - Top View

31/4 ''

(8.26 cm)

rain.

--(6.35 mm)max.

Hinge Side

__J

= t

"T"

If an extended handle kit is used, route the handle side W' (6.35 mm). All other routing dimensions would remain the same as the standard handle. Make sure your product location will allow doors with extended handles to be opened to 90 degrees. See "Door Swing Dimensions."

For more information on ordering extended handles, see "Classic Series Factory Panels and Kits."

1/4" (6.36 mm) max, |

2" (5 cm)

rain.

Door Panel

Panel Door !J

1 "

(2.54 cm)

® _[ Door

Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

• The dimensions shown are actual product dimensions

and may not reflect the needed panel installation dimensions.

• The side panel should be a minimum of V_"(1.27 cm) thick

to avoid warping.

• If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on rear wall.

Panel

] "

(2,54 cm)

Refrigerator

NOTE: For both types of handles, route the top and bottom edges W' (1.3 cm).

24_/s.

(61,3 cm)

(60,3 cm)

231/2 ''

(59,7 cm)

23_ '/_e"

Side Trim

2. Route the front edge of the support board or attach a 1/4"

(6,35 mm) board to hold the panel in the cabinet side trim,

1/4"

(6.35 mm)

-_4/%"mrn)

3/16"

(4.7 mm)

7/32"

(5.5 mm)

1a/a2"(19 ram)

(15.7 mm)

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add 7/32"(5.6 mm) to this measurement to allow the side panel to fit into the trim,

2. If the panel is more than 1/4"(6.35 mm) thick, route the front edge to allow the side panel to fit into the trim.

Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is plaoed at the end of a cabinet run. You may choose an Inset or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

• The dimensions shown are actual product dimensions and may not reflect the needed installation dimensions.

• The side panel should be a minimum of 1/2"(1.27 cm) thick to avoid warping.

• If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on rear wall.

Refrigerator

Overlay

Flush Installation Dimensions

1. Measure the distance from point A (as shown) to the back wall,

2. Attach the support board with a screw or adhesive that is compatible with aluminum and wood.

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back wall.

Side Trim

(9.7 mm)

1/16"

(1,5 rnm)

3/8"

_" _--- (4.5 ram)

3/16"

Inset Installation Dimensions

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add %2" (0.8 mm) to this measurement to allow the side panel to fit into the trim.

2. If the panel is more than 3/8"(9.5 mm) thick, route the front edge to allow the side panel to fit into the trim.

INSTALLATION INSTRUCTIONS

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT:

• Do not remove the protective film until the refrigerator is in its operating position.

• All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator.

• Keep the cardboard shipping piece or plywood under the refrigerator until it is installed in the operating position.

Remove and save the literature package bag taped to the side of the refrigerator and the parts bag behind the grille. Remove the four brackets (two on each side) that attach the shipping base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the refrigerator is in its final position.

If necessary, reduce the tipping radius. See "Tipping Radius" for ceiling height requirements or "Reduce Tipping Radius" for step-by-step instructions. Ifyou do not need to reduce the tipping radius, proceed to "Move the Refrigerator into

House."

1. Measure the distance from point A (as shown) to back wall.

2. Route the front edge of the support board or attach a %" (9.5 mm) board to hold the panel in the cabinet side trim.

Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See "Tipping Radius."

If you do not have adequate ceiling height to stand the refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart).

Model Reduced Tipping Radius

36 88" (223.5 cm) 42 881/2'' (224.8 cm) 48 891/4'' (226.7 cm)

Classic and Overlay Series

1. Grasp both ends of the top grille.

2. Push the top grille straight up, then pull straight out. Lay the grille on a soft surface.

A B

A. Top grille B. Cabinet side trim

Remove the six screws attaching each cabinet side trim to the refrigerator and remove the side trims.

Architect ®Series

1. Grasp both ends of the louver panel, Push the louver panel

straight up, then pull straight out, Lay the panel on a soft surface.

2. Grasp both ends of the top grille, Push the top grille straight up, then pull straight out. Lay the top grille on a soft surface,

B A B

A. Topgrille B. Cabinet side trim

C. Louver panel

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

3. Remove the six screws attaching each cabinet side trim to

the refrigerator and remove the side trims.

Pro Line _Series

1. Grasp both ends of the top grille,

2. Push the top grille straight up, and then pull straight out.

3. Disconnect the wiring harness from the back of the top grille.

4. Lay the top grille on a soft surface.

5. Remove the six screws that attach each cabinet side trim to

the refrigerator, and remove the side trims,

6. Reattach wiring harness into grille back.

7. Insert top grille hooks into slots on the side trim. Pull grille down slightly to lock into place,

1. Place an appliance dolly under the left side of the refrigerator as shown. Be sure to protect the side trims and handles. Place the corner posts from the packing materials over the trims and handles as appropriate. Slowly tighten the strap.

NOTE: Pass the dolly strap under the handles for the Architect ®Series.

2. Place pieces of the shipping carton on the floor when rolling the dolly and refrigerator into the house. Move the refrigerator close to the built-in opening.

3. Place top of cardboard carton or plywood under refrigerator.

4. Stand the refrigerator up. First, place the left bottom edge of the refrigerator on the floor, stand the refrigerator upright and then lower the right-hand side of the refrigerator to the floor.

5. Do not remove protective film or cover.

6. Reassemble the trim and top grille after the dolly has been removed from the refrigerator.

IMPORTANT: Pro Line®Series only. Reattach wiring harness into grille back.

IMPORTANT:

• It is recommended that board(s) be installed before the refrigerator is installed.

• Board(s) must be long enough to fully cover the width of the compressor cover.

• Locate the board(s) so the bottom surface(s) of the board(s) is(are) 84" (213 cm) from the floor.

During installation, raise the refrigerator up so there is W' (6.35 mm) maximum between the top of the refrigerator and the bottom of the anti-tip board(s). Do not crush the compressor cover when raising the rear leveling legs.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall 80" to 90" (203 cm to 229 cm) above floor.

2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards to wall studs behind refrigerator. Use six #8 x 3" (7.6 cm) (or longer) wood screws. The wood screws must be screwed into the studs at least 11/2"(3.8 cm). The board(s) must overlap the compressor cover.

A B

Read all directions before you begin. IMPORTANT: Ifyou turn the refrigerator on before the water line

is connected, turn the ice maker OFE

Style I - Shutoff Valve Connection

NOTE: If your water line connection does not look like Style 1, see "Style 2 - Copper Line Connection."

1. Unplug refrigerator or disconnect power supply. IMPORTANT: Before attaching the tubing to shutoff valve, flush

the main water supply line to remove particles and air inthe water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

2. Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.

3. Thread the provided nut onto the shutoff valve as shown.

A B

.............C

2" (5 cm) _ _:_

A. Center board _" (6.35mm) max. above refrigerator

B. Two2" x 4" x 32" (5 cm x 10cm x 81 cm) boards C.Attach to studs with six #8 x 3" (7.6 cm)screws

D. Compressor cover

A.Bulb B.Nut

C. Watertubing

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

6. Plug in the refrigerator or reconnect power.

7. Flush the water system. See "Water System Preparation."

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

Style 2 - Copper Line Connection

Connecting to Water Line NOTE: If existing water line meets the "Water System

Requirements," see "Connecting to Refrigerator."

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a V2"to 1W' (1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold water pipe you have selected,

G ,_ ..........B

8. Flush the water system. See "Water System Preparation."

NOTE: Allow 24 hours to produce the first batch of ice, Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

A. Cold water pipe B. Pipe clamp

C. Copper tubing D. Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4"(6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp, Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal, Do not overtighten, or you may crush the copper tubing•

7. Slip the compression sleeve and compression nut on the copper tubing as shown, Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten the clamp or the sleeve. This will crush the copper tubing•

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air inthe water line. Allow enough flow so that water becomes clear• Flushing the water line may help avoid filters and/or water valves from becoming clogged•

8. Turn off the shutoff valve on the water pipe. Coil the copper tubing,

9. Check for leaks around the saddle valve.

Connecting to Refrigerator

1. Unplug the refrigerator or disconnect power•

2. Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.

3. Measure the distance from the shutoff valve to the opening in which the refrigerator will be located. Tubing must be extended from the shutoff valve into the refrigerator opening following specific guidelines. See "Water Supply Requirements."

4. A 1/4"x 1/4"(6,35 mm to 6,35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing,

E. Compression sleeve F. Shutoff valve

G. Packing nut

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1. Set control switch at top of cabinet to the OFF position,

2. Plug into a grounded 3 prong outlet.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

A B C D E F G

A. Water tubing E. Ferrule(purchased)

B.Nut F Nut (purchased) C.Bulb G.Household water line(as D.Coupling (purchased) connected in previous section)

5. Turn shutoff valve ON.

6. Check for leaks• Tighten any nuts or connections (including connections at the valve) that leak.

7. Plug in the refrigerator or reconnect power•

IMPORTANT: To avoid floor damage, make sure levelers are raised (not touching floor) and refrigerator is on rollers before moving.

1. Place top of cardboard carton or plywood under refrigerator. Remove dolly.

2. Do not remove protective film or cover•

3. Move the refrigerator straight back and evenly into the opening, Be sure that the refrigerator side trims are not interfering with the door opening. Also, be sure that the water tubing is not kinked and the power supply cord is on top of the refrigerator•

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: All four leveling legs must contact the floor to support and stabilize the full weight of refrigerator. Rollers are for moving refrigerator and not for permanent support,

After moving the refrigerator to its final location:

1. Use a %6" socket driver to turn the leveling bolts clockwise to extend the legs to the floor as shown. The rollers should be

off the floor.

A. Rear leveling bolt

B. Front leveling bolt

Adjust the leveling legs to level and align the refrigerator from left to right and front to back so that the refrigerator is level and aligned with the cabinetry. The cabinetry surface must be plumb for the ideal fit of the refrigerator side trim.

Continue adjusting all of the leveling legs to raise the refrigerator until the top is within at least 1" (2.54 cm) of the top soffit.

NOTE: If an anti-tip board has been used, adjust the leveling legs until the top of the refrigerator is within 1/4"(6.35 mm) of the bottom of the anti-tip board as shown. Do not crush the

compressor cover.

...............C

_'- 1/4" (6 ram)

2"(scm) --_ "1.,

max

A.Centerboard ¼" (6.35mm) max. above refrigerator B.Two 2" x 4" x32" (5cm x 10cm x 81 cm)boards C.Attach tostuds with six #8 x3" (7.6 cm)screws O.Compressor cover

IMPORTANT: Adjust in small increments to keep from damaging the cabinet trim and causing problems with the door alignment or top grille fit. To avoid damage to the cabinet or leveling legs, do not apply more than 50 inch- pounds (5.65 Nm) of torque to the leveling bolts. The leveling legs can be extended to a maximum of 11/4'' (3.18 cm) below

the rollers.

For Classic and Overlay models, additional adjustments may be needed after the custom panels are installed.

IMPORTANT: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service.

Door Panels

1. Remove all tape and door bracing from the refrigerator and freezer doors.

2. Remove the screws that attach the handles to the door frame.

3. Slide the decorative door panels into the door frames.

If needed, route the door panels or install a filler panel between the doors and the decorative panels. See the

"Classic Series Custom Panels" section in "Installation Requirements."

-A

IltlllllllllllllltllltllllllllllllllttlliltllllllllllllllltliI

A. Panels

5. Replace the door handles. Install the top screw on each handle first. Be sure that the top of both door handles are aligned.

6. If the door handles are not aligned, loosen all handle screws and adjust door handles up or down. Tighten the screws.

7. Check refrigerator level and adjustment. Adjust if needed.

Top Grille Panel

1. Grasp both ends of the top grille.

2. Push straight up, then pull straight out. Place the top grille panel-side down on a soft working surface.

B A B

4. Slide the backer panel into the top grille channel and reattach the end cap.

A. Backerpanel

5. Replace the top grille in the cabinet side trims and pull the panel down slightly to lock it into place.

B A B

A. Topgrille

B. Cabinetside trim

IMPORTANT:

• Install the custom handles prior to installing the panels on

the refrigerator. For more information on KitchenAid custom handle selection, refer to the KitchenAid Catalog,

visit www.kitchenaid.com, or call 1-800-442-9991. In Canada, visit www.KitchenAid.ca, or call 1-800-806-6777.

• Create custom door overlay panels according to the

specifications in the "Overlay Series Custom Panels" section.

• KitchenAid is not responsible for the removal or addition

of molding or decorative panels that would not allow access to the refrigerator for service.

A. Top grille

B. Cabinet side trim

Remove one end cap by loosening the nuts and sliding off the end cap.

A. Bottom rail C. End cap B. Nuts D. Top rail

Door Panel Installation

1. Remove all tape and door bracing from the refrigerator and freezer doors.

2. Open the refrigerator and freezer compartment doors.

+ 53 hidden pages