KitchenAid KSSO48FTX18, KSSO42FTX18, KSSO36FTX18, KSSC48QVS06, KSSC48FTS18 Installation Guide

...

Ki|chen_kid _

SIDE BY SIDE BUILT-IN REFRIGERATOR

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.

REFRIGERADOR EMPOTRADO

DE DOS PUERTAS

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. kA INSTALACION REQUIERE DE 20 MAS PERSONAS.

P P P J_. % J_.

REFRIGERATEUR ENCASTRE COTE A COTE

{_,,_, _,_ ......

IMPORTANT : LIRE IT CONSERVER CES INSTRUCTIONS. L'INSTALLATION NiCESSlTE L'INTERVENTION DE 2 PERSONNES OU PLUS.

Table of Contents/[ndice/Table des matieres .................................................................. 2

W10555563A

TABLEOF CONTENTS

REFRIGERATOR SAFETY ............................................................. 3

MODELS .......................................................................................... 4

INSTALLATION REQUIREMENTS ................................................ 6

Tools and Parts ............................................................................ 6

Location Requirements ................................................................ 6

Electrical Requirements ............................................................... 7

Water Supply Requirements ........................................................ 8

Tipping Radius ............................................................................. 8

Product Dimensions ..................................................................... 9

Door Swing Dimensions ............................................................. 10

Overlay Series Door Panel and Cabinetry Clearance ................ 11

Overlay Series Custom Panels and Handle Kits ....................... 13

Classic Series Factory Panels and Kits ..................................... 15

Classic Series Custom Panels ................................................... 16

Classic, Architect ®and Complete Series

Custom Side Panels ................................................................... 18

Overlay Series Custom Side Panels .......................................... 18

INDICE

SEGURIDAD DEL REFRIGERADOR ........................................... 28

MODELOS ..................................................................................... 29

REQUlSITOS DE INSTALACION ................................................. 31

Piezas y herramientas ................................................................ 31

Requisitos de ubicaci6n ............................................................. 31

Requisitos electricos .................................................................. 32

Requisitos del suministro de agua ............................................. 33

Arco de vuelco ........................................................................... 33

Medidas del producto ................................................................ 34

Medidas de oscilaci6n de las puertas ....................................... 35

Espacio para el panel de la puerta y para los armarios

de la serie de paneles recubiertos ............................................. 36

Paneles a la medida y juegos de manijas

de la serie de paneles recubiertos ............................................. 38

Paneles y juegos de fabrica de la serie Classic ........................ 40

Paneles a la medida para de la serie Classic ............................ 41

Paneles laterales a la medida para las

series Classic, Architect ®y Complete ........................................ 43

Paneles laterales a la medida para la

serie de paneles recubiertos ...................................................... 44

INSTALLATION INSTRUCTIONS ................................................ 19

Unpack the Refrigerator............................................................. 19

Reduce Tipping Radius.............................................................. 20

Move the Refrigerator into House .............................................. 20

Install Anti-Tip Boards ................................................................ 20

Connect the Water Supply ......................................................... 21

Plug in Refrigerator ..................................................................... 22

Move Refrigerator to Final Location........................................... 22

Level and Align Refrigerator ....................................................... 23

Install Classic Series Custom Panels ......................................... 23

Install Overlay Series Custom Panels ........................................ 24

Adjust Doors ............................................................................... 25

Install Side Panel ........................................................................ 26

Install Base Grille ........................................................................ 26

Complete Installation.................................................................. 27

Water System Preparation ......................................................... 27

INSTRUCCIONES DE INSTALACION ......................................... 45

Desempaque el refrigerador ...................................................... 45

C6mo reducir el arco de vuelco ................................................. 45

C6mo hacer entrar el refrigerador en la casa ............................ 45

C6mo instalar los tableros antivuelco ........................................ 46

Conexi6n del suministro de agua .............................................. 46

C6mo enchufar el refrigerador ................................................... 48

C6mo mover el refrigerador a su ubicaci6n final ....................... 48

Nivelaci6n y alineamiento del refrigerador ................................. 48

C6mo instalar los paneles a la medida

para la serie Classic ................................................................... 49

Como instalar los paneles a la medida para

la serie de paneles recubiertos .................................................. 50

Ajuste las puertas ....................................................................... 51

Como instalar el panel lateral ..................................................... 52

Como instalar la rejilla de la base .............................................. 52

Como terminar la instalacion ..................................................... 53

Preparacion del sistema de agua .............................................. 53

TABLEDES MATIERES

SECURITE DU REFRIGERATEUR .............................................. 54

MODELES ..................................................................................... 55

EXIGENCES D'INSTALLATION ................................................... 57

Outillage et pieces ...................................................................... 57

Exigences d'emplacement ......................................................... 57

Specifications electriques .......................................................... 58

Specifications de I'alimentation en eau ..................................... 59

Rayon de basculement .............................................................. 59

Dimensions du produit ............................................................... 60

Dimensions pour I'ouverture des portes .................................... 61

Serie Panneaux decoratifs - Panneau de porte

et placard - espace libre ............................................................ 62

Panneaux personnalises et poignees de la serie

Panneaux decoratifs .................................................................. 64

Ensembles de panneaux d'origine de la serie Classic .............. 66

Panneaux personnalises de la serie Classic .............................. 67

Panneaux lateraux personnalises

des series Classic, Architect ®et Complete ................................ 69

Panneaux lateraux personnalises de la serie Overlay ............... 70

INSTRUCTIONS D'INSTALLATION ............................................. 70

Deballage du r6frigerateur .......................................................... 70

Reduction du rayon de basculement ......................................... 71

Faire entrer le refrig6rateur dans le domicile ............................. 71

Installation de planches antibasculement .................................. 72

Raccordement &I'alimentation en eau ...................................... 72

Branchement du r6frigerateur .................................................... 74

Deplacement du refrig6rateur & I'emplacement final................. 74

Reglage de I'aplomb et alignement du refrig6rateur ................. 74

Installation des panneaux personnalises

de la serie Classic ....................................................................... 75

Installation des panneaux personnalises

de la serie Panneaux decoratifs ................................................. 76

Ajustement des portes ............................................................... 77

Installation du panneau lateral ................................................... 78

Installation de la grille de la base ............................................... 78

Achever I'installation .................................................................. 79

Preparation du systeme d'eau ................................................... 79

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

Side by Side Non-Dispensing Refrigerators

MODELS

Architect _ Series Features wraparound styling that complements the contoured

door handles. This series provides a warm commercial-looking built-in refrigerator.

KSSC36FTS KSSC42FTS KSSC48FTS

Classic Series

Features factory-installed, traditional style trim to provide a "framed" look. This series requires the installation of custom

panels that are not included. KSSS36FTX KSSS42FTX KSSS48FTX

Overlay Series Features factory-installed, overlay style trim to provide a

"frameless" look. This series requires the installation of custom panels, handles, and standoffs.

KSSO36FTX KSSO42FTX KSSO48FTX

Side by Side Dispensing Refrigerators

Architect _ Series

Features wraparound styling that complements the contoured door handles. This series provides a warm commercial-looking

built-in refrigerator. KSSC36QTS KSSC42QTS KSSC48QTS

Classic Series

Features factory-installed, traditional style trim to provide a "framed" look. This series requires the installation of custom

panels that are not included. KSSS36QTB KSSS42QTB KSSS48QTB KSSS36QTW KSSS42QTW KSSS48QTW

KSSS36QTX KSSS42QTX KSSS48QTX

iii i_ _i iiI

Overlay Series

Features factory-installed, overlay style trim to provide a "frameless" look. This series requires the installation of custom

panels, handles, and standoffs. KSSO36QTB KSSO42QTB KSSO48QTB

iii

Complete Series Features factory-installed stainless steel trim and panels to create

a sleek, contemporary look. KSSP36QTS KSSP42QTS KSSP48QTS

INSTALLATION REQUIREMENTS

IMPORTANT:

• Installer: Leave Installation Instructions with the homeowner.

• Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local

electrical inspector's use.

Tools Needed Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed here.

• Cordless drill

• Drill bits

• Two adjustable wrenches

• Phillips screwdriver

• Small level

• Appliance dolly

Parts Needed

• Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)

• One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)

• Order factory panels, make custom panels or consult a qualified cabinetmaker or carpenter to make the panels.

Classic Series: Order factory panels, make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See "Classic Series Custom Panels" for more

information. Overlay Series: Make custom panels, or consult a qualified

cabinetmaker or carpenter to make the panels. See "Overlay Series Custom Panels and Handle Kits" for more information.

Architect _ and Complete Series are shipped complete.

• If you are connecting the water line directly to copper tubing and not to a shutoff valve, you need aferrule, a union, and a V4"(6.35 mm) compression fitting.

• Torx_tT27 screwdriver

• _Y32"Nut driver

• 3/8"and W' Open-end wrenches

• 8/32" Hex key

• 1/4"and _e" Socket drivers

• Tape measure

• Utility knife

The refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to enclose the refrigerator.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator. Failure to do so can result in death, explosion, or fire.

IM PORTANT:

• Observe all governing codes and ordinances.

• It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source.

• Do not install in a location where the temperature will fall below 55°F (13°C).

• Floor must support the refrigerator weight, more than 600 Ibs (272 kg), door panels and contents of the refrigerator.

• Ceiling height must allow for side tipping radius. See "Tipping Radius."

• Location should permit door to open fully. See "Door Swing Dimensions."

• Location must permit top grille removal. See "Opening Dimensions."

Opening Dimensions

To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. Ifthe solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the rear wall studs 80" to 90" (203 cm to 229 cm) above the floor. See "Install Anti-Tip Boards" for more information.

NOTE: A clearance of V2"(1.3 cm) must be maintained above the top grille in order for the top grille to be removed.

t®TORX is a registered trademark of Saturn Fasteners, Inc.

• A grounded 3 prong electrical outlet should be located within a specified number of inches from the right-hand side cabinets or end panel. See the chart following the graphic for the number of inches required for your model. For more information, see "Electrical Requirements."

• The water shutoff should be located in the base cabinet on either side of the refrigerator or some other easily accessible

area. If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor or the back wall. See "Water Supply Requirements" for more

information.

£:i',1@CI: /_,,@;]!

Electrical Shock Hazard

831/2" (212.1 cm) min. 843/4" (215 cm) max.

to bottom of solid soffit

JJ JJ

ii 80"-g0"ii

i i(203-229 cm)ii

Width

(see chart following)

Plug into a grounded 3 prong outlet.

Dimension

77"

(196 cm)

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection. Recommended Grounding Method

A 115 volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. IMPORTANT: If this product is connected to a GFCI (Ground

Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, remove the top grille and turn the master power switch to OFF or disconnect power at the circuit breaker

box. When you are finished, turn ON the master power switch or

reconnect power at the circuit breaker box. Then reset the control to the desired setting.

24"

(60.96 cm) rain.

Width A Width A for Dimension B

(as shown Overlay Models (as shown

Model above) (as shown above) above)

36 351/2"to 353/4'' 353/4'' to 36" 4" (10.2 cm)

(90.2 cm to (90.8 cm to

90.8 cm) 91.4 cm)

42 411/2"to 413/4" 413/4"to 42" 10" (25.4 cm)

(105.4 cm to (106 cm to 106 cm) 106.7 cm)

48 471/2''to 473/4'' 473/4'' to 48" 16" (40.6 cm)

(120.7 cm to (121.3 cm to

121.3 cm) 121.9 cm)

NOTE: Flooring under refrigerator must be at same level as the room. Face of cabinetry must be plumb.

(15.2 c

Water Pressure

Allinstallationsmustmeetlocalplumbingcoderequirements. Thewatershutoffshouldbelocatedinthebasecabineton

eithersideoftherefrigeratororsomeothereasilyaccessible area.Theright-handsideisrecommended.Theaccesshole throughthecabinetmustbewithin1/2"(12.7mm)oftherear

wall. NOTE:Ifthewatershutoffvalveisinthebackwallbehindthe

refrigerator,itmustbeatananglesothatthetubeisnot kinkedwhentherefrigeratorispushedintoitsfinallocation.

(15.2 cm)

24"

(60.96 cm) min.

• If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor. A 1/2"(12.7 mm) hole for plumbing should be drilled at least 6" (15.2 cm) from the right or left hand side cabinet or panel. On the floor, the hole should be no more than 1" (2.54 cm) away from the back wall. See "Connect the Water Supply."

• If additional tubing is needed, use copper tubing and check for leaks. Install the copper tubing only in areas where the household temperatures will remain above freezing.

• Do not use a piercing-type or 3/le"(4.76 mm) saddle valve which reduces water flow and clogs more easily.

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

• If your refrigerator has a water filter cartridge, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed, qualified plumber.

Be sure there is adequate ceiling height to stand the refrigerator upright when it is moved into place.

• The dolly wheel height must be added to the tipping radius when a dolly is used.

• If needed, the tipping radius can be reduced. See "Reduce Tipping Radius."

Side Tipping Radius

The side tipping radius varies depending upon the width of the model. Use the chart provided to determine the side tipping

radius. NOTE: Tip on side only.

ii ii

Model Tipping Radius A

36 901/2'' (229.9 cm) 42 93" (236.2 cm) 48 96" (243.8 cm)

Side View

Front View

• The depth from the front of the top grille to the back of the refrigerator cabinet is 253A" (64.5 cm).

• The power cord is 84" (213 cm) long.

• The water line attached to the back of the refrigerator is 5 ft (1.5 m) long.

• Height dimensions are shown with leveling legs extended 1/8" (3 mm) below the rollers.

253/8"

---_

(64.5 cm)

231/2"

(59.7 cm)

"833/8"

(211.8 cm)

84" (213.4 cm)

Power Cord

• Width dimensions were measured from trim edge to trim edge.

• Height dimensions are shown with leveling legs extended 1/8" (3 mm) below the rollers.

*83%"

(211.8 cm)

"31/2" (8.9 cm)

*When leveling legs are fully extended to 1V4"(3.2 cm) below

rollers, add 1V8" (2.9 cm) to the height dimensions.

Top View

253/8'' (64.5 cm)

Model Width A

36 35" (88.9 cm) 42 41" (104.1 cm) 48 47" (119.4 cm)

(seechart following)

Model Width A (Trim edge to trim edge)

36 361/4"(92.1 cm) 42 421/4'' (107.3 cm) 48 481/4"(122.6 cm)

*When leveling legs are fully extended to 1V4"(3.2 cm) below

rollers, add 1V8" (2.9 cm) to the height dimensions.

Thelocationmustpermitbothdoorstoopentoaminimumof 90°.Allow4W'(11.4cm)minimumspacebetweenthesideofthe refrigeratorandacornerwall.

NOTE:Moreclearancemayberequiredifyouareusingoverlay panels,customhandles,orextendedhandlesonaClassic

model. Toadjustthedoorswing,see"AdjustDoors."

42" (106.7 cm) Models

36" (91.4 cm) Models

107/8"

(27.6 cm)

443/8,,

(112.7 cm)

48" (121.9 cm) Models

143/8"

(36.5 cm)

99 m)

<--167,/8 '' -_'" |

(42.9 cm) |

477/8,,

(121.6 cm)

(48.9 cm)

513/8"

(130.5 cm)

The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If the refrigerator is to be installed close to the wall, see "Door Swing 90°,' on next page.

Door Swing 110 °

Actual Size

Refrigerator to

Cabinetry Clearance

Refrigerator Side Trim

Hinge

NOTE: For Overlay Series models, rout the hinge side of the custom door panels to a radius that is equal to at least half the

thickness of the panel if a 130° door swing is desired. See "Adjust Doors."

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

Panel

90° Door

Stop Position

Refrigerator Side Trim

(1.9 cm)

/2 ',

(1.3,cm)i

,, ,,

i i i i

Cabin,'etr_/

Door Swing 90 °

Actual Size

Refrigerator to Cabinetry Clearance

(2.5 cm)

3/4"

Hinge

1//2"

(1.30m)

(1.90m) i

"--II m

1/4"(6.35 mm)

1/2"(1.3 cm)

3/4"(1.9 cm)

1" (2.5 cm)

3//4"

I 1"

(2.5cm)

11//4"

(3.2 cm)

11/2"

(3.8cm)

jj_

Spacer Panel

Allow a minimum of 41/2"(11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if thicker custom panels or custom handles are used. Do not overlook baseboards.

Custom overlay panels allow you to blend the exterior of your refrigerator into the overall kitchen decor, and to use custom handles for additional design flexibility.

The custom panels must have backer panels attached in order to mount them to the refrigerator. It is most common to work with three panels, as shown in the following graphic: a decorative overlay panel, a V8" (3.18 mm) spacer panel or spacer strips and a V4" (6.35 mm) backer panel.

In some cases, your cabinet manufacturer may choose to work with one panel routed for the different dimensions. Follow these panel dimension and placement instructions to be sure that the custom overlay panels will fit properly.

IM PORTANT:

• The weight of the refrigerator door overlay panel cannot exceed 50 Ibs (23 kg).

• The weight of the freezer door overlay panel cannot exceed 40 Ibs (18.1 kg).

• The weight of the top grille overlay panel cannot exceed 10 Ibs (4.5 kg).

To minimize panel weight, you may use 2" (5.08 cm) spacer strips around the perimeter in place of full-sheet solid spacer panels. The spacer strips must be set in at least 1" (2.54 cm) from the top, bottom and sides edges of the backer panel. If you use spacer strips, it is also recommended that you use two 2" (5.08 cm) strips horizontally centered for added support.

Overlay Panel

Spacer Panel

I Spacer Panel

'[]

Vs. _

Overlay Panel

Backer Panel

ri,

l_ 1" minimum .

I (2.54 cm[. ......

Backer Panel

(15.88 to Va,, (6.35 mm)

19.05 ram) (3.18 ram)

I ,_'D'oer/Grille Trim

_*_ Offset Dimension

Decorative Overlay Panel

(18.4 cm)

71/4" I

Freezer

DoorPanel

Preferred

Radius

1/2,,

(1.27 em)

141/4"

(36.2 cm)

(Dispenser)

.,_-10_/a,,--_

(27.5em) 7 " DFre_zerIrP_

Refrigerator Door Panel

(183

Dispenser

cutout is centered

337/8 ''

(86.0em)

left-to-right

Model A B C

36 143/4"(37.47cm) 193/4"(50.17 cm) 343/4"(88.27cm)

42 17V4" (43.82 cm) 231/4" (59.06 cm) 403/4" (103.51 cm)

48 193/4" (50.17 cm) 263/4" (67.95 cm) 463/4" (118.75 cm)

*Represents placement of dispenser frame.

Backer Panels

Dispenser Frame (dispenser models only)

NOTES:

• Dashed lines represent placement of backer panels on overlay panels.

• Illustration shows backer panels placed on decorative overlays.

63/16" I(15.7 cm)

Top Offset

_[" 15/a'' (4.13 cm)

....

22"

(55.9 cm)

701/2''

(179.1 cm)

Bottom Offset _ 1/2"(12.7 mm) 1/2" (1.27 cm) --

I I I

Handle-

Side Offset

1/4,,

(6.4 mm)

sF,---t - ' eOffset

701/2''

(179.1 cm)

The dispenser frame attaches to the panel with 4 screws. To remove the dispenser frame:

1. Remove the four screws attaching the frame.

2. Pull the dispenser frame from the decorative panel.

3. To replace the frame, hold the frame to the panel and replace the screws.

-_ ..... III

331/4 '' '

(84.5 cm) ,

_ . )'___.......

t Bottom Offset £ Bottom Offset __q&

1/8" (3.2 mm) 1/8"(3.2 mm)

Model D E F

36 141/4'' (36.20 cm) 191/4'' (48.90 cm) 333/4'' (85.73 cm) 42 163/4'' (42.55 cm) 223/4'' (57.79 cm) 393/4'' (100.97 cm) 48 191/4'' (48.90 cm) 261/4'' (66.68 cm) 453/4'' (116.21 cm)

A. Decorative panel B. Refrigerator door C. Dispenser frame

The dispenser frame overlaps the dispenser cutout by %e" (0.78 cm) on each side and 1/2"(1.27 cm) on the top and bottom.

A A

A. ½" (1.27 cm) Overlap

Overlay Series Door Handle Kits

Architect _ Series

The following handle styles are available. Contact your KitchenAid dealer or KitchenAid Parts and Accessories at

1-800-442-9991. In Canada, call 1-800-807-6777.

B C D

A. ArchitecP Series handle (4396103)

B. Flat end straight handle (4396776) with stainless steel

clamshell standoffs (4396775)

C. Round end arc handle (4396779) with bronze bullet

standoffs (4396778)

D. Round end semicircle (4396777) with stainless steel

cylinder standoffs (4396782)

Handles

These handles can be installed on side-by-side and bottom- freezer refrigerators that require overlay panels.

Part Number Description

Satin Stainless Steel

4396781 Flat End Straight - 45" (114.3 cm) Length,

Satin Stainless Steel

4396777 Round End Semicircle,

Satin Stainless Steel*

4396779 Round End Arc,

Satin Stainless Steel*

*Availablefor non-dispensing models only.

Standoffs

The kit includes screws to support 3/4" applications. Standoffs can be installed on side-by-side and bottom-freezer

refrigerators that require overlay panels. NOTES:

• Two standoffs must be ordered for each handle.

• Handles and standoffs may be combined to meet your individual decorating needs.

Part Number Description

4396775 Clamshell, Satin Stainless Steel 4396780 Clamshell, Satin Bronze

Handles

Part Number Color

4396103 Stainless Steel

8171760 Biscuit 4396105 White 4396106 Black

(.,lass:<: Is_@ttes :acI}}o w I: alset5 a:t_cI _'

All factory parts are available through your KitchenAid dealer or by calling KitchenAid Parts and Accessories at 1-800-442-9991.

In Canada, call 1-800-807-6777.

Factory Door Panel Kits

Three kits containing colored acrylic or stainless steel door and top grille panels are available. Follow the kit instructions for installing the panels.

NOTE: Panel kits are not required for factory-installed stainless steel panel models.

Door Panel Part Numbers for Non-dispenser Models

Color 36 42 48

White #2325136 #2325137 #2325138

Black #2325139 #2325140 #2325141

Stainless Steel #2325142 #2325143 #2325144

Door Panel Part Numbers for Dispenser Models

Color 36 42 48

White #2325127 #2325128 #2325129

Black #2325130 #2325131 #2325132

Stainless Steel #2325133 #2325134 #2325135

Extended Door Handle Kits

Use extended door handles when additional finger clearance is needed between the door handles and custom panel. Follow the kit instructions for installing the door handles.

Color Part Number

White #4387990

Black #8171418

Stainless Steel #4388062

Matte Aluminum #4387989

4396774 Bullet, Satin Stainless Steel 4396778 Bullet, Satin Bronze

4396782 4396773

Cylinder, Satin Stainless Steel Cylinder, Satin Bronze

If you plan to install custom wood panels, you will need to create the panels yourself or consult a qualified cabinetmaker or carpenter. See dimension drawings for panel specifications.

IMPORTANT: Panels weighing more than recommended may cause damage to your refrigerator.

NOTE: Dimensions shown have a (+)Vie" (1.5 mm) tolerance. Panels that are more than V4"(6.35 mm) thick must be routed. If panels are less than V4"(6.35 mm) thick, install a filler panel between the doors and decorative panels.

Top Grille Panel

The top grille panel should not weigh more than 10 Ibs (4.5 kg). NOTE: The dashed lines in the illustration represent the location

and offsets of raised wood panel.

A _..i

-I

7" i

(17.78 cm)

1/4" thick 11/16"(1.75 cm) plywood

Top & Bottom Offsets___

Model A

36 34V4" (87.0 cm) 42 40V4" (102.2 cm) 48 46_A'' (117.5 cm)

-_11 S_ide Offsets

-_ "17/16" (1.11 cm)

Door Panels for Non-dispenser Models

The freezer panel should not weigh more than 40 Ibs (18.1 kg). The refrigerator panel should not weigh more than 50 Ibs (23 kg).

_t_ 7-

1/2,,

(1.27 cm)

I- ..... I

Freezer

Door

I I I I

_--B_

Refrigerator

Door

__t_ 7-

1/2,,

(1.27 cm)

(Non-Dispenser)

._ 7/16"

(1.1 cm)

W' thick .................

plywood

I 1 I

, 3 V4'_..,

,(8.3 cm) i

.... t

7/16" ._

(1.1 cm)/

_- W' Location and offsets W'

I 31/4.

(8.3 cm)

I I I I

(1.27 cm) of raised wood panel (1.27 cm)

V4"thick plywood

Model A B

36 141/4"(36.2 cm) 191/4"(48.9 cm) 42 163/4"(42.6 cm) 223/4"(57.8 cm) 48 19V4" (48.9 cm) 26V4" (66.7 cm)

NOTES:

• If the standard handle is used, the handle side offset of both panels should be 3V4" (8.25 cm) to all for finger

clearance.

If an extended handle is used, the handle side offset of both panels should be 7/le"(1.1 cm). Make sure the

refrigerator location allows the doors with extended handles to open to 90 degrees. See "Door Swing

Dimensions."

The dashed lines in the illustration represent the location and offsets of raised wood panel.

Door Panels for Dispenser Models

Dispenser Frame (Classic series dispenser models)

The freezer panel should not weigh more than 40 Ibs (18.1 kg). The refrigerator panel should not weigh more than 50 Ibs (23 kg).

_t_ 7-

(1.27 cm)

141/4"

(36.2 cm)

1/2,,

Freezer

Door

(Dispenser)

I I I

_-- B -_

Refrigerator

Door

1/2,,

(1.27 cm)

7/16"

(1.1 cm)

Dispenser

cutout is centered

left-to-right

333/4"

(85.7 cm)

(8.3 cm) ,

I I

31/4,_,,

I I I

The dispenser frame attaches to the panel with 4 screws.

To remove the dispenser frame:

1. Remove the four screws attaching the frame.

2. Pull the dispenser frame from the decorative panel.

3. To replace the frame, hold the frame to the panel and replace the screws.

7/16" ..._

(1.1 cm)/

1/2,, Location andoffsets 1/2,,

(1.27 cm) of raised wood panel (1.27 cm)

Model A B

36 141/4"(36.2 cm) 19W' (48.9 cm) 42 163/4"(42.6 cm) 223/4"(57.8 cm)

48 191/4"(48.9 cm) 26W' (66.7 cm)

NOTES:

Dispenser cutout is centered left-to-right. If the standard handle is used, the handle side offset of

both panels should be 31/4'' (8.25 cm) to all for finger clearance.

If an extended handle is used, the handle side offset of both panels should be 7/le"(1.1 cm). Make sure the

refrigerator location allows the doors with extended handles to open to 90 degrees. See "Door Swing Dimensions."

The dashed lines in the illustration represent the location and offsets of raised wood panel.

A.Dispenser frame

The dispenser frame overlaps the dispenser cutout by 5/le" (0.78 cm) on each side and 1/2"(1.27 cm) on the top and bottom.

A. ½" (1.27 cm) Overlap

Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

• The dimensions shown are actual product dimensions and may not reflect the needed panel installation

dimensions.

• The side panel should be aminimum of 1/2"(1.27 cm) thick to avoid warping.

• If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on rear wall.

Refrigerator

241/8"

(61.3 cm)

'TT

(60.3 cm)

231/2"

(59.7 cm)

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back wall. Add 7/32"(5.6 mm) to this measurement to allow the side panel to fit into the trim.

2. If the panel is more than V4"(6.35 mm) thick, route the front edge to allow the side panel to fit into the trim.

Flush Installation Dimensions

1. Measure the distance from point A (as shown) to the back wall.

2. Attach the support board with a screw or adhesive that is compatible with aluminum and wood.

Side Trim

(6.35 mm)

(15.7 mm)

11/64"

(4.5 mm)

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back wall.

2. Route the front edge of the support board or attach a V4" (6.35 mm) board to hold the panel in the cabinet side trim.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

• The dimensions shown are actual product dimensions

and may not reflect the needed installation dimensions.

• The side panel should be a minimum of 1/2,,(1.27 cm) thick

to avoid warping.

• If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on rear wall.

Refrigerator

SideTrim

3/8"

(9.7 mm)

Overlay

2311/16 ''

(60.16 cm)

3/1611

(4.5 mm)

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to back wall.

2. Route the front edge of the support board or attach a 3/8" (9.5 mm) board to hold the panel in the cabinet side trim.

A I

¢--

INSTALLATION

INSTRUCTIONS

1_611

(1.5 mm)

3/32"

(2.38 mm)

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back wall. Add 1/32"(0.8 mm) to this measurement to allow the side panel to fit into the trim.

2. If the panel is more than 3/8"(9.5 mm) thick, route the front edge to allow the side panel to fit into the trim.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IM PO RTANT:

• Do not remove the film covering until the refrigerator is in its operating location.

• All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator.

• Keep the cardboard shipping piece or plywood under the refrigerator until it is installed in the operating location.

1. Remove and save the literature package bag taped to the side of the refrigerator and the parts bag behind the grille. Remove the four brackets (two on each side) that attach the shipping base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the refrigerator is in its final location.

2. If necessary, reduce the tipping radius. See "Tipping Radius" for ceiling height requirements or "Reduce Tipping Radius" for step-by-step instructions. If you do not need to reduce the tipping radius, proceed to "Move the Refrigerator into

House."

Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See "Tipping Radius" in the "Installation Requirements" section for

more information. If you do not have adequate ceiling height to stand the

refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart).

Model Reduced Tipping Radius

36 88" (223.5 cm) 42 881/2'' (224.8 cm) 48 891/4'' (226.7 cm)

1. Grasp both ends of the top grille.

2. Push the top grille straight up; then pull straight out. Lay the grille on a soft surface.

B A B

NOTE: Pass the dolly strap under the handles for the Architect ®Series.

[ I

2. Place pieces of the shipping carton on the floor when rolling the dolly and refrigerator into the house. Move the refrigerator close to the built-in opening.

3. Place top of cardboard carton or plywood under refrigerator.

4. Stand the refrigerator up. First, place the left bottom edge of the refrigerator on the floor, stand the refrigerator upright and then lower the right-hand side of the refrigerator to the floor.

5. Reassemble the trim and top grille after the dolly has been removed from the refrigerator.

A. Top grille B. Cabinet side trim

Remove the six screws attaching each cabinet side trim to the refrigerator and remove the side trims.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

kll_l I - I I!11);!I[dl S

........... i

To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

• It is recommended that board(s) be installed before the refrigerator is installed.

• Board(s) must be long enough to fully cover the width of the compressor cover.

• Locate the board(s) so the bottom surface(s) of the board(s) is(are) 84" (213 cm) from the floor.

• During installation, raise the refrigerator up so there is 1/4"(6.35 mm) maximum between the top of the refrigerator and the bottom of the anti-tip board(s). Do not crush the compressor cover when raising the rear leveling legs.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall 80" to 90" (203 cm to 229 cm) above floor.

Place an appliance dolly under the left side of the refrigerator as shown. Place the corner posts from the packing materials over the trims and handles as appropriate to avoid damage. Slowly tighten the strap.

Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards to wall studs behind refrigerator. Use six #8 x 3" (7.6 cm) (or longer) wood screws. The wood screws must be screwed into the studs at least 11/2'' (3.8 cm). The board(s) must overlap the compressor cover.

)

....... ° °

A. Center board ¼" (6.35 mm) max. above refrigerator B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards C.Attach to studs with six #8 x 3" (7.6 cm) screws D. Compressor cover

Read all directions before you begin. IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFE

LL:_

2" (5 cm)

3. Place the end of the tubing into a bucket, and turn shutoff valve ON.

4. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Style 2--Copper Line Connection NOTE: If there is a water supply line that meets the specifications

in "Water Supply Requirements," proceed to "Connecting to Refrigerator." If not, use the following instructions to connect to the household cold water supply.

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2"to 1V4"(1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IM PO RTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and keep normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from the connection on the refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use V4"(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a V4" (6.35 mm) hole in the cold water pipe you have selected.

Connect to Water Line

Parts Needed:

• Minimum 7 ft (2.13 m) flexible, codes approved water supply line

Style 1--Shutoff Valve Connection NOTE: If your water line connection does not look like Style 1,

see "Style 2--Copper Line Connection."

1. Unplug refrigerator or disconnect power supply.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

2. Connect the flexible, codes approved water supply line to the water shutoff valve by threading the provided nut onto the

shutoff valve as shown.

Cold waterpipe E.Compression sleeve

Pipe clamp F. Shutoff valve

Copper tubing G.Packing nut

Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the V4"(6.35 mm) drilled hole inthe water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air in the water

line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from

becoming clogged.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten the clamp or the sleeve. This will crush the copper tubing.

8. Turn off the shutoff valve on the water pipe. Coil the copper tubing.

9. Connect the flexible, codes approved water supply line to the water shutoff valve by threading the provided nut onto the

shutoff valve.

10. Place the end of the tubing into a bucket, and turn shutoff valve ON.

11. Check for leaks around the saddle valve. Tighten any nuts or connections (including connections at the valve) that leak.

Connect to Refrigerator

Parts Supplied:

• 1/4"to 1/4"6.35 mm to 6.35 mm)male-to-male coupling

I I I I

6" 6"

(17.78 cm)

NOTE: The flexible, codes approved water supply line should connect to the supply valve through the floor.

1. Unplug the refrigerator or disconnect power.

2. Connect the 7 ft (2.13 m) flexible codes approved water tube to the water supply valve.

3. Flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes

clear.

4. Tape the 7 ft (2.13 m) flexible codes approved water supply line to the floor, 7" (17.78 cm) from the left side of the

refrigerator. Tape along the length of the tubing, which will allow it to pass beneath the refrigerator without interference.

NOTE: Allow a minimum of 26" (66.04 cm) of flexible codes approved water supply line to be loose at the front of the

refrigerator for connecting to the refrigerator.

5. Connect the 7 ft (2.13 m) flexible codes approved water supply line to the refrigerator.

NOTE: If the main water shutoff valve is behind the refrigerator, a secondary water shutoff valve may be installed in line with the water supply line at the front of the product.

IIl I =0" ]" _') ' ' ':'_"'°<'ii........

III li'_,,@III!,!_ I _';I(I

I.I

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Set control switch at top of cabinet to the OFF position.

2. Plug into a grounded 3 prong outlet.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: To avoid floor damage, make sure levelers are raised (not touching floor) and refrigerator is on rollers before moving.

1. Place top of cardboard carton or plywood under refrigerator. Remove dolly.

2. Do not remove film or cover.

3. Move the refrigerator straight back and evenly into the opening. Be sure that the refrigerator side trims are not interfering with the door opening. Also, be sure that the water tubing is not kinked and the power supply cord is on top of the refrigerator.

A. Household water line B. Nut (purchased)

C. Ferrule (purchased) D. Coupfing

E.Bulb F Nut

G. Re frigera tor water tubing

6. Turn on the water supply valve and check all connections for leaks.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: All four leveling legs must contact the floor to support and stabilize the full weight of refrigerator. Rollers are for moving refrigerator and not for permanent support.

After moving the refrigerator to its final location:

1. Use a %e" socket driver to turn the leveling bolts clockwise to extend the legs to the floor as shown. The rollers should be

off the floor.

A B

/4" (6 rnrn)

max.

2" (5 cm)

A.Center board ¼"(6.35mm) max. above refrigerator B. Two2" x 4" x 32" (5 cm x 10cm x 81 cm) boards C.Attach to studs with six#8 x 3" (7.6cm) screws D.Compressor cover

IMPORTANT: Adjust in small increments to keep from damaging the cabinet trim and causing problems with the door alignment or top grille fit. To avoid damage to the cabinet or leveling legs, do not apply more than 50 inch-pounds (5.65 Nm) of torque to the leveling bolts. The leveling legs can be extended to a maximum of 1V4"(3.18 cm) below the rollers.

For Classic and Overlay models, additional adjustments may be needed after the custom panels are installed.

LmS7 \

A. Rear leveling bolt B. Front leveling bolt

Adjust the leveling legs to level and align the refrigerator from left to right and front to back so that the refrigerator is level and aligned with the cabinetry. The cabinetry surface must be plumb for the ideal fit of the refrigerator side trim.

Continue adjusting all of the leveling legs to raise the refrigerator until the top is within at least 1" (2.54 cm) of the top soffit.

NOTE: If an anti-tip board has been used, adjust the leveling legs until the top of the refrigerator is within V4"(6.35 mm) of the bottom of the anti-tip board as shown. Do not crush the compressor cover.

IMPORTANT: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service.

Door Panels

1. Remove all tape and door bracing from the refrigerator and freezer doors.

2. Remove the screws that attach the handles to the door frame.

3. Slide the decorative door panels into the door frames.

4. If needed, route the door panels or install a filler panel between the doors and the decorative panels. See the

"Classic Series Custom Panels" section in "Installation Requirements.

---4

A ....

IMMMMIIIIIIIIIIIIMMMMIIIIIIIII

A. Panels

5. Replace the door handles. Install the top screw on each handle first. Be sure that the top of both door handles are aligned.

6. If the door handles are not aligned, loosen all handle screws and adjust door handles up or down. Tighten the screws.

7. Check refrigerator level and adjustment. Adjust if needed.

Top Grille Panel

Grasp both ends of the top grille.

Push straight up, then pull straight out. Place the top grille panel-side down on a soft working surface.

B A B

A. Top grille

B. Cabinet side trim

Remove one end cap by loosening the nuts and sliding off the end cap.

IM PO RTANI"."

/ ..........

• Install the custom handles prior to installing the panels on the refrigerator. For more information on KitchenAid custom handle selection, refer to the KitchenAid Catalog, visit www.kitchenaid.com, or call 1-800-442-9991. In Canada,

visit www.KitchenAid.ca, or call 1-800-807-6777.

• Create custom door overlay panels according to the specifications in the "Overlay Series Custom Panels" section.

• KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service.

Door Panel Installation

1. Remove all tape and door bracing from the refrigerator and freezer doors.

2. Open the refrigerator and freezer compartment doors.

3. Remove the handle-side and top trims.

A.Bottom rail C.End cap B.Nuts D. Toprail

Slide the backer panel into the top grille channel and reattach the end cap.

A. Backer panel

Replace the top grille in the cabinet side trims and pull the panel down slightly to lock it into place.

B A B

IIIIIIIIIIIIIMMMMIIIIIIIIIIIMMMIII

A. Trims

Slide the custom panels into the bottom and hinge side trims on the refrigerator compartment and freezer compartment doors, making sure that the backer panel fits into the hinge

side trims.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

.... A

A. Panels

A. Top grille

B. Cabinet side trim

+ 56 hidden pages