KitchenAid KSRX25FSWH00, KSRX25FSST00, KSRX25FSBL00, KSRX22FSWH00, KSRX22FSST00 Owner’s Manual

...

REFRIGERATOR USE & CARE GUIDE

MANUAL DE USO Y CUIDADO DEL

GUIDE D'UTILISATION ET D'ENTRETIEN DU

Table of Contents / Indice / Table des mati_res

ASSISTANCE OR SERVICE ............................ 1

REFRIGERATOR SAFETY ............................... 2

INSTALLATION INSTRUCTIONS ................... 3

REFRIGERATOR USE ..................................... 5

REFRIGERATOR CARE ................................... 9

TROUBLESHOOTING .................................... 10

WATER FILTER CERTIFICATIONS .............. 12

PRODUCT DATA SHEETS ............................ 13

WARRANTY .................................................... 15

Kitchen kid

REFRIGERADOR

p p

REFRIGERATEUR

AYUDA O SERVICIO TleCNICO .................... 16

SEGURIDAD DEL REFRIGERADOR ............ 16

INSTRUCCIONES DE INSTALACION .......... 17

USO DE SU REFRIGERADOR ...................... 20

CUIDADO DE SU REFRIGERADOR ............. 25

SOLUCION DE PROBLEMAS ....................... 26

HOJA DE DATOS DEL PRODUCTO ............ 29

GARANTJA ...................................................... 31

ASSISTANCE OU SERVICE .......................... 32

SleCURITle DU RleFRIGleRATEUR ................ 32

INSTRUCTIONS D'INSTALLATION .............. 33

UTILISATION DU RleFRIGleRATEUR ........... 36

ENTRETIEN DU RleFRIGleRATEUR ............. 41

DlePANNAGE .................................................. 42

FEUILLES DE DONNleES SUR

LE PRODUlT ................................................... 45

GARANTIE ..................................................... 47

Assistance or Service

If you need assistance or service, first see the "Troubleshooting" section. Additional help is available. Call us at 1-800-422-1230

from anywhere in the U.S.A., or write:

KitchenAid Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Information may also be obtained by visiting our website at

www.kitchenaid.com.

In Canada, for assistance, installation or service, call:

1-800-807-6777, or write:

KitchenAid Canada

Customer Interaction Centre

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

In Canada, visit www.KitchenAid.ca.

Please include a daytime phone number in your correspondence. Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation date for in-warranty service.

Write down the following information about your appliance to help you obtain assistance or service if you ever need it. You will need

to know your complete model number and serial number. You can find this information on the model and serial number label, located on the inside wall of the refrigerator compartment.

Dealer name Serial number

Address Phone number

Model number Purchase date

Toorder replacement filters, call 1-800-442-9991 and ask for the part number listed below or contact your authorized KitchenAid

dealer. In Canada, call f-800-807-6777.

Stainless Steel Cleaner and Polish: Order Part #4396095 Standard Base Filter Cartridge:

Order Part #4396841 (T2RFWG2) In Canada, Order Part #4396841B (T2RFWG2)

2315184

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured ifyou don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline, away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice or water (on some

models).

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily climb inside.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

NOTE: It is recommended that you do not install the refrigerator

near an oven, radiator, or other heat source. Do not install in a location where the temperature will fall below 55°F (13°C).

1/2"(1.25 crn)/

Remove packaging materials. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the surface of your

refrigerator. For more information, see "Refrigerator Safety."

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

II -- i_!

2" (5.08 cm) !

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for W'

(1.25 cm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on each side (depending on your model) to allow for the door to

swing open. If your refrigerator has an ice maker, allow extra space at the back for the water line connections.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the control (Thermostat, Refrigerator or

Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.

Gathertherequiredtoolsandpartsbeforestartinginstallation. Readandfollowtheinstructionsprovidedwithanytoolslisted

here.

TOOLS NEEDED:

• Flat-blade screwdriver • %" Drill bit

• 7/16"and 1/2"Open-end or two • Hand drill or electric drill adjustable wrenches (properly grounded)

• 1/4"nut driver

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/16"

(4.76 mm) saddle valve which reduces water flow and clogs more easily.

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 - 827 kPa) is required to operate the water dispenser and ice maker. Ifyou have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 - 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 - 414 kPa). If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 - 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

• If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See "Water Filtration System."

If you have questions about your water pressure, call a licensed, qualified plumber.

Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of the refrigerator

to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold water pipe you have selected.

......................A

F E D _

A. Cold waterpipe E.Compressionsleeve B.Pipe clamp F Shutoff valve C. Copper tubing G.Packing nut D.Compression nut

6. Fasten shutoff valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the 1/4"(6.35 mm) drilled hole in the water pipe and that washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws slowly and evenly

so the washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw the compression nut onto the outlet end with an adjustable wrench. Do not overtighten.

8. Place the free end of the tubing into a container or sink, and turn ON main water supply and flush out the tubing until water

is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the shipping tape and the black nylon plug from the gray, coiled water tubing on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long enough, a 1/4"x 1/4"coupling is needed in order to connect the water tubing to an existing household water supply line. Thread the provided nut onto the coupling on the end of the

copper tubing. NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

Read all directions before you begin. IMPORTANT: If you turn the refrigerator on before the water line is

connected, turn the ice maker OFR

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2"(12.70 mm) to 11/4'' (3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

A B C D E F G

A. Refrigerator water tubing E.Ferrule (purchased)

B. Nut (provided) F Nut (purchased)

C. Bulb G. Household water line D. Coupling (provided)

Turn shutoff valve ON.

Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the shipping tape and the black nylon plug from the gray, coiled water tubing on the rear of the refrigerator.

3. Threadtheprovidednutontothewatervalveasshown. NOTE:Tightenthenutbyhand.Thentightenitwithawrench

twomoreturns.Donotovertighten.

A.Bulb B.Nut (provided)

Turn shutoff valve ON.

Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Water and Ice Dispensers." NOTE: It may take up to 24 hours for your ice maker to begin

producing ice.

REFRIGERATOR USE

For your convenience, your refrigerator controls are preset at the

factory. When you first install your refrigerator, make sure that the

controls are still preset. The Refrigerator Control and the Freezer Control should both be set to the "mid-settings."

Your model may have Slide Controls, Electronic Controls or Digital Controls.

IMPORTANT (All Controls):

• The Refrigerator Control adjusts the refrigerator compartment temperature. The Freezer Control adjusts the freezer

compartment temperature.

• Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your

food may spoil. NOTE: Adjusting the Refrigerator and Freezer Controls to a

higher (colder) than recommended setting will not cool the compartments any faster.

• If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

• The preset settings should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

• Wait at least 24 hours between adjustments. Recheck the temperatures before other adjustments are made.

Slide Controls (on some models)

Style 1

Freezer Refrigerator

C )

cold 1 2 ,_ 3 4 colder off 1 2 A 3 4 colder

Style 2

Freezer Refrigerator

Off 1 2 • 3 4 Colder Cold 1 2 • 3 4 Colder

IMPORTANT:

• For Style 1, your product will not cool when the Refrigerator control is set to OFE For Style 2, your product will not cool

when the Freezer Control is set to OFE

• The Automatic Exterior Moisture control continuously guards against moisture buildup on the outside of your refrigerator cabinet. This control does not have to be set or adjusted.

Adjusting Slide Controls

Settings to the left of the mid-setting make the temperature less cold. Settings to the right of the mid-setting make the temperature

colder.

• Slide the FREEZER or REFRIGERATOR control one setting to the right or left depending on the needed temperature change.

NOTE:ForStyle1,afteradjustingtherefrigerator temperature,wait24hoursandthenrechecktheFREEZER

temperaturebeforemakingadditionaladjustments.

CONDITION: SETTINGADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Control

one setting lower

REFRIGERATOR too warm REFRIGERATOR Control

one setting higher

FREEZER too cold FREEZER Control

one setting lower

FREEZER too warm/too little ice FREEZER Control

one setting higher

Accelerated Ice Production

This feature assists with temporary periods of heavy ice usage by increasing ice production over a 24-hour period.

• Press ICE touch pad to set the freezer temperature to -10°F (-23°C). The Accelerated Ice setting will remain on for 24 hours unless manually turned off. The display will continue to show your normal temperature set point.

NOTE: If increased ice production is desired at all times, set the Freezer Control to a colder setting. Adjusting the freezer to a colder temperature may make some foods, such as ice cream, harder.

Electronic Controls (on some models)

FREEZER REFRIGERA_R

_ C0LD C010ER f,,_ COLD COLDER

_123@567

turn the refriger_or on, press and hold ON_FF for 2 seconds.

The indicator lights show the current temperature control seftings.

Adjusting Electronic Controls

Settings to the left of the mid-sefting make the temperature less cold. Settings to the right of the mid-sefting make the temperature

colder.

• Press the FREEZER or REFRIGERATOR arrow to move the indicator light to the right, one setting at a time. Continue

moving the indicator light until it is at the desired setting.

NOTE: With each press of the arrow, you will hear a beep as the light moves to the next setting. The indicator light moves to a setting of "7" and then returns to the setting of "1 ."

CONDITION: SETTING ADJUSTMENT: REFRIGERATOR too cold REFRIGERATOR Control

one setting lower

REFRIGERATOR too warm REFRIGERATOR Control

one setting higher

FREEZER too cold FREEZER Control

one setting lower

FREEZER too warm/too little ice FREEZER Control

one setting higher

0000000

Digital Controls (on some models)

Warmer FREEZER REFRIGERATORWarmer

Colder Colder

Toturn the refrigerator on, press and hold POWER (ON/OFF) for 2 seconds.The factory recommended set points are 0°F (-18°C)

for the freezer and 37°F (3°C) for the refrigerator. NOTES:

• To view Celsius temperatures, press the °C SELECT pad. The indicator will light up. To return the display setting to

Fahrenheit, press the °C SELECT pad again.

• If the freezer temperature is below zero, the negative sign next to the freezer display will light up.

Adjusting Digital Controls The set point range for the freezer is -5°F to 5°F (-21 °C to -15°C).

The set point range for the refrigerator is 33°F to 41 °F (1°C to 5°C).

• To adjust the set point temperatures, press the refrigerator or freezer PLUS (+) or MINUS (-) pad until the desired

temperature is reached.

CONDITION: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Control

1° lower

REFRIGERATOR too warm REFRIGERATOR Control

1° higher

FREEZER too cold FREEZER Control

1° lower

FREEZER too warm/too little ice FREEZER Control

1° higher

Max Cool The Max Cool feature assists with periods of heavy ice usage, full

grocery loads, or temporarily warm room temperatures.

• Press MAX COOL pad to turn on the Max Cool feature. The Max Cool indicator light will remain on for 24 hours unless manually turned off.

NOTE: The temperature display will not change. After 24 hours, the refrigerator returns to the previous temperature set points.

Accelerated Ice Production (on some models)

This feature assists with temporary periods of heavy ice use by

increasing ice production over a 24-hour period.

• Press OPTIMICE ®feature touch pad to turn on the Optimlce ° feature. The Optimlce ®setting will remain on for 24 hours unless manually turned off.

• If increased ice production is desired at all times, set the Freezer Control to a colder number. Setting the freezer to a colder temperature may make some foods, such as ice cream,

harder.

Temperature System

The Temperature System feature lets you know the compressor or

evaporator fan is running. It is normal for this indicator light to be

on.

Temperature

System

C( *_ve:_:tbk __)r :_wer .............. ......... ..........

The control can be adjusted to properly chill meats or vegetables. The air inside the pan is cooled to prevent "spot" freezing and can

be set to keep meats at the National Livestock and Meat Board

recommended storage temperatures of 28° to 32°F (-2° to 0°C). The convertible vegetable/meat drawer control comes preset at the lowest meat setting.

To store meat:

Set the control to one of the three MEAT settings to store meat at

its optimal storage temperature.

To store vegetables:

Set the control to VEG to store vegetables at their optimal storage temperatures.

NOTE: If food starts to freeze, move the control to the left (less

cold). Remember to wait 24 hours between adjustments.

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) for best storage of fruits and vegetables with skins.

NIGH (closed) for best storage of fresh, leafy vegetables.

Cool air from the freezer is directed to the refrigerator door bin

directly beneath the vents.

NOTE: The dairy compartment and can rack are not associated

with the Chilled Door Bin feature.

Chilled Door Bin Control

• Slide the door chill control to the left to reduce the flow of cold air to the bin and make it less cold.

• Slide the door chill control to the right to increase the flow of cold air to the bin and make it colder.

...... ,. ........

Depending on your model, you may have one or more of the following options: the ability to select either crushed or cubed ice,

a special light that turns on when you use the dispenser, a special AUTO mode, or a lock option to avoid unintentional dispensing.

NOTES:

• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before

or after the system.

• If your model has a base grille filter system, make sure the base grille filter is properly installed.

• The dispensing system will not operate when the freezer door is open.

• After connecting the refrigerator to a water source, flush the water system by dispensing water into a sturdy container until you draw and discard 1.5 gal. (5.4 L) of water, or for

approximately 3 minutes after the water begins dispensing. The flushing process cleans the water system and clears air from the lines. As the air is cleared from the lines, water may spurt out of the dispenser.

• Allow several hours for the refrigerator to cool down and chill water.

• Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

The Water Dispenser

IMPORTANT: Dispense enough water every week to maintain a

fresh supply.

To Dispense Water:

1. Press a sturdy glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer. The dispensing system will not operate when the freezer door is open. Toturn off the ice maker, see "Ice Maker & Storage Bin."

Some models dispense both cubed and crushed ice. Before dispensing ice, select which type of ice you prefer.

For crushed ice, cubes are crushed before they are dispensed. This may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in size. When changing from crushed to cubed, a few ounces of crushed ice will be dispensed along with the first cubes.

The chilled door bin control is located on the left-hand side of the

refrigerator compartment.

A. Chilled door bin control

To Dispense Ice:

1. Press button for the desired type of ice.

Cut Hazard

Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.

Style 1

Toturn off the dispenser, press the LOCK button until the indicator appears. The ice and water dispensers will not work. To unlock

the dispenser, press the UNLOCK button until the indicator appears. Then continue to dispense ice or water as usual.

Style 2

Toturn off the dispenser, press and hold the LOCK OUT button until the indicator appears. The ice and water dispensers will not

work. To unlock the dispenser, press the LOCK OUT button until the indicator disappears. Then continue to dispense ice or water

as usual,

Turning the Ice Maker On/Off

2. Press a sturdy glass against the ice dispenser lever. Hold the

glass close to the dispenser opening so ice does not fall outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to the lever in order to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

The Dispenser Light

Style 1

The dispenser area has a light. It can be turned on manually by

pressing the ON button (touch pad or rocker switch). On some models: Whenever you use the dispenser the lever will

automatically turn the light on.

LIGHT

OFF ON

Style 2 When you use the dispenser, the lever will automatically turn the

light on. If you want the light to be on continuously, you may choose either ON or AUTO.

On Auto

@@ @D

LIGHT

ON: Press the LIGHT button to turn the dispenser light on.

AUTO: Press the LIGHT button a second time to select the AUTO

mode. The dispenser light will automatically adjust to become brighter as the room brightens, dimmer as the room darkens.

OFF: Press the LIGHT button a third time to turn the dispenser light off.

The dispenser lights are LEDs which should not need to be

changed. If it appears that your dispenser lights are not working, check to be sure that the light sensor is not blocked (in AUTO mode). See "Troubleshooting" for more information.

Style 1

Toturn ON the ice maker, simply lower the wire shutoff arm. To manually turn off the ice maker, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click. NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin, and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

Style 2

The ON/OFF switch is located on the top right-hand side of the freezer compartment.

Toturn on the ice maker, slide the control to the ON (left) position. To manually turn off the ice maker, slide the control to the OFF

(right) position. NOTE: Your ice maker has an automatic shutoff. The ice maker

sensors will automatically stop ice production, but the control will remain in the ON (left) position.

REMEMBER:

• Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

• The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to

poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well

maintained.

• Do not use anything sharp to break up the ice in the storage bin. This can cause damage to the ice container and the

dispenser mechanism.

• Do not store anything on top of or in the ice maker or storage bin.

Removing and Replacing Ice Storage Bin

Style 1

1. Pull the covering panel up from the bottom and then slide it back toward the rear.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position. Ice can still be dispensed, but no more can be made.

3. Lift up the front of the storage bin and pull it out.

The Dispenser Lock (on some models)

Your dispenser can be turned off for easy cleaning or to prevent unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator,

to the ice maker, or to the dispenser light. It simply deactivates the

dispenser levers.

Replace the bin by pushing it in all the way or the dispenser will not work. Push the wire shutoff arm down to the ON

position to restart ice production. Make sure the door is closed tightly.

Style 2

1. Hold the base of the storage bin with both hands and press

the release button to lift the storage bin up and out. NOTE: It is not necessary to turn the ice maker control to the

OFF (right) position when removing the storage bin. The sensor cover ("flipper door") on the left wall of the freezer stops the ice maker from producing ice if the door is open or

the storage bin is removed.

2. Replace the storage bin on the door and push down to make sure it is securely in place.

NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Water Filter Status Light (on some models)

The water filter status light will help you know when to change your water filter. The light will change from green to yellow. This tells you that it is almost time to change the filter. It is

recommended that you replace the water filter when the status light changes to red OR water flow to your water dispenser or ice

maker decreases noticeably.

After changing the water filter, reset the water filter status light. The status light will change from red to green when the system is reset.

Non-indicator Water Filter (on some models)

If your refrigerator does not have the status light, you should change the water filter every 6 months depending upon your

usage. If the water flow to the water dispenser or ice maker decreases noticeably before 6 months have passed, replace the

water filter more often.

Using the Dispenser Without the Water Filter

You can run the dispenser without a water filter. Your water will not be filtered.

1. Remove the water filter.

2. Slide the cap off the end of the filter and replace the cap in the base grille.

IMPORTANT: Do not discard the cap. It is part of your refrigerator. Keep the cap to use with the replacement filter.

3. Rotate the cap until it is securely in position.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately. IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent

odor transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator: NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm water.

There is no need for routine condenser cleaning in normal home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Removethe base grille.

• Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the bulb with one of the same size, shape and wattage. On some models, the dispenser light requires a heavy duty 10-watt bulb. All

other lights require a 40-watt bulb. Replacement bulbs are available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable. NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size, shape and wattage.

4. Replace light shield when applicable.

5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

• Power cord unplugged? Plug into a grounded 3 prong outlet.

• Is outlet working? Plug in a lamp to see if the outlet is working.

• Household fuse blown or circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues,

call an electrician. Are controls on? Make sure the refrigerator controls are on.

See "Using the Controls." New installation? Allow 24 hours following installation for the

refrigerator to cool completely. NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The refrigerator is noisy

Refrigerator noise has been reduced over the years. Due to this reduction, you may hear intermittent noises from your new refrigerator that you did not notice from your old model. Below are listed some normal sounds with an explanation.

• Buzzing - heard when the water valve opens to fill the ice maker

• Pulsating - fans/compressor adjusting to optimize performance

• Rattling - flow of refrigerant, water line, or from items placed on top of the refrigerator

• Sizzling/Gurgling - water dripping on the heater during defrost cycle

• Popping - contraction/expansion of inside walls, especially during initial cool-down

• Water running - may be heard when water melts during the defrost cycle and runs into the drain pan

• Creaking/Cracking - occurs as ice is being ejected from the ice maker mold.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct position.

The doors are difficult to open

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its high-efficiency compressor and fans. The unit may run even longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

Are the gaskets dirty or sticky? Clean gaskets with mild soap and warm water.

The lights do not work

• Is a light bulb loose in the socket or burned out? See "Changing the Light Bulbs."

• Is the dispenser light set to ON? The dispenser light will operate only when the levers are pressed. If you want the dispenser light to stay on continuously, set the dispenser light to ON, or NIGHT LIGHT or AUTO. See "Water and Ice

Dispensers."

• Is the dispenser light set to NIGHT LIGHT or AUTO? If the dispenser is set to the NIGHT LIGHT or AUTO mode, be sure the dispenser light sensor is not blocked. See "Water and Ice

Dispensers."

Off-taste, odor or gray color in the ice

Temperature is too warm

• New installation? Allow 24 hours following installation for the refrigerator to cool completely.

• Door(s} opened often or left open? Allows warm air to enter refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions? Adjust the controls a setting colder. Check temperature in 24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s} opened often or left open? Allows humid air to enter refrigerator. Minimize door openings and keep doors fully

closed.

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch (depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice

production.

• Large amount of ice recently removed? Allow 24 hours for ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm? Remove ice from the ejector arm with a plastic utensil.

• Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure.

See "Water Supply Requirements" in either the Installation Instruction booklet or the Use & Care Guide.

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.

• Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a licensed, qualified plumber.

• New plumbing connections? New plumbing connections can cause discolored or off-flavored ice.

• Ice stored too long? Discard ice. Wash ice bin. Allow 24 hours for ice maker to make new ice.

• Odor transfer from food? Use airtight, moisture proof packaging to store food.

• Are there minerals (such as sulfur) in the water? A water filter may need to be installed to remove the minerals.

• Is there a water filter installed on the refrigerator? Gray or dark discoloration in ice indicates that the water filtration

system needs additional flushing.

The ice dispenser will not operate properly

• Freezer door closed completely? Close the door firmly. If it does not close completely, see "The doors will not close

completely."

• Ice bin installed correctly? Be sure the ice bin is firmly in position.

• New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice

production.

• Ice stuck in the delivery chute? Use a plastic utensil to clear the delivery chute.

• Has the wrong ice been added to the bin? Use only cubes produced by the current ice maker.

• Has the ice melted around the auger (metal spiral} in the ice bin? Dump the ice cubes and clean the ice bin.

Cut Hazard

Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.

• Is the ice dispenser stalling while dispensing "crushed" ice? Change the ice button from "crushed" to "cubed." If cubed ice dispenses correctly, depress the button for

"crushed" ice and begin dispensing again.

• Has the dispenser arm been held in too long? Ice will stop dispensing when the arm is held in too long. Wait 3 minutes for dispenser motor to reset before using again.

The water dispenser will not operate properly

• Freezer door closed completely? Close the door firmly. If it does not close completely, see "The doors will not close

completely."

• Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open,

• Is the water pressure at least 30 psi (207 kPa)? The water pressure to the home determines the flow from the dispenser. See "Water Supply Requirements."

Kink in the home water source line? Straighten the water source line.

New installation? Flush and fill the water system.

Water filter installed on the refrigerator? The filter may be

clogged or incorrectly installed. Is a reverse osmosis water filtration system connected to

your cold water supply? See "Water Supply Requirements" in either the Installation Instructions or the Use & Care Guide,

Water is leaking from the dispenser

NOTE: One or two drops of water after dispensing is normal.

• Glass not being held under the dispenser long enough? Hold the glass under the dispenser 2 to 3 seconds after releasing the dispenser lever.

• New installation? Flush the water system, See "Water and Ice Dispensers,"

• Recently changed water filter? Flush the water system. See "Water and Ice Dispensers,"

The dispenser water is not cool enough

NOTE: Water from the dispenser is chilled to only 50°F (10°C).

• New installation? Allow 24 hours after installation for the water supply to cool completely.

• Recently dispensed large amount of water? Allow 24 hours for water supply to cool completely,

• Water not been recently dispensed? The first glass of water may not be cool. Discard the first glass of water.

• Refrigerator connected to a cold water pipe? Make sure the refrigerator is connected to a cold water pipe, See "Water

Supply Requirements,"

WATER FILTER

CERTIFICATIONS

Stale of CMiforma

Depattmem of Health Services

Water Treatment Device

CertificateNumber

05- 1703

Dale Issued: April 6, 2/X)5

Date Revised Septemi_'l 7, 201)q

rademark/Model Designation

WhMpo_l Deluxe T2WG2

WhMpool D_]uxe T2WG2L

RatedServiceCapacfiy: 200gals RatedServieeFlow: 085gpm

Do not use with waler lhat is microbiolngica)ly uns_de or of _nk(_>wn qualJty, wifl_t adequate disinku:tion beff,re or after _he system¸

Conditions of Certification:

State of California

Department of Health Services

WaterTreatmentDevice

CertificateNumber

05- 1702

Date Issued: ApnI 6, 2005

Date Revised: September 7, 2005

Tradenlark/Model Designation

Whirlpool De01xe [lWG2 T2RI WG2

Manufaeturem Wtur/_,l/i ¢oilxl, a6 o n

The _ater tl It {o Section 116830 of t

Replacement Elements

No_e

'_!ili

,, , :i!7/51;!ilii;ii!iiii

Rated Service Capaci_': 200 ga)s Rated Service Flo_: 0 5 gpm

Do not use with water that is microbmlogicalIy tmsale or of mlknown quality, withom adequate disinfectmn b_fore or after the system

Conditions of Certification:

PRODUCT DATA SHEETS

Base Grille Water Filtration System

Model T2WG2LfT2RFWG2 Capacity 200 Gallons (758 Liters)

Model T2WG2/T2RFWG2 Capacity 200 Gallons (758 Liters)

Tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor, Particulate Class II*; and

against NSF/ANSI Standard 53 for the reduction of Mercury, Benzene, Toxaphene, O-dichlorobenzene, and Carbofuran.

This system has been tested according to NSF/ANSl 42/53 for the reduction of the substances listed below. The concentration of the

indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSl 42/53.

Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %

Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction

Chlorine Taste/Odor 50% reduction 2.0182 mg/L 2.0 mg/L _+10% I 0.06 mg/L ** 0.0536 mg/L 97.03 97.34 Particulate Class II* 85% reduction 1333333 #/mL At east 10,000 part c es/mL 6600 #/mL 2325 #/mL 99.51 99.83

Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum % Average % Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction

Lead: @ pH 6.5*** 0.010 mg/L 0.1533 mg/L 0.15 mg/L _+10% 0.0005 mg/L 0.0005 mg/L 99.67 99.67 Lead: @ pH 8.5*** 0.010 mg/L 0.1400 mg/L 0.15 mg/L _+10% 0.0007 mg/L 0.0006 mg/L 99.50 99.57

Mercury: @ pH 6.5 0.002 mg/L 0.0058 mg/L 0.006 mg/L _+10% 0.0002 mg/L 0.0002 mg/L 96.54 96.54 Mercury: @ pH 8.5 0.002 mg/L 0.0059 mg/L 0.006 mg/L _+10% 0.0005 mg/L 0.0003 mg/L 91.57 94.92

Benzene 0.005 mg/L 0.0154 mg/L 0.015 mg/L _+10% 0.0012 mg/L 0.0006 mg/L 92.22 96.34 O-Dichlorobenzene 0.6 mg/L 1.7571 mg/L 1.8 mg/L _+10% 0.0250 mg/L 0.0066 mg/L 98.58 99.63

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 mg/L _+10% 0.001 mg/L 0.001 mg/L 93.33 93.33

Carbofuran 0.04 mg/L 0.0819 mg/L 0.08 mg/L _+10% 0.0400 mg/L 0.0213 mg/L 51.13 74.00

Test Parameters: pH = 7.5 _+0.5 unless otherwise noted. Flow = 0.85 gpm (3.2 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C).

• It is essential that operational, maintenance, and filter replacement requirements be carried out for the product to perform as advertised.

• Use replacement cartridge T2RFWG2, part #4396841. In Canada, use replacement cartridge T2RFWG2, part #4396841B. 2006 suggested retail price of $39.99 U.S.A./ $49.99 Canada. Prices are subject to change without notice.

Model T2WG2L: Press FILTER to check the status of your water filter. If the filter indicator light is yellow, order a new

filter. Ifthe filter indicator light is red, it is recommended that you replace the filter.

Model T2WG2: Change the water filter cartridge every 6 months depending upon your usage. Ifthe water flow to the

water dispenser or ice maker decreases noticeably before 6 months have passed, replace the water filter cartridge more

often.

• These contaminants are not necessarily in your water supply. While testing was performed under standard laboratory conditions, actual performance may vary.

• The product is for cold water use only.

• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

• Refer to the "Assistance or Service" section for the Manufacturer's name, address and telephone number.

• Refer to the "Warranty" section for the Manufacturer's limited warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well Water Pressure 30 - 120 psi (207 - 827 kPa) Water Temperature 33 ° - 100°F (0.6 ° - 37.8°C) Service Flow Rate 0.85 gpm (3.2 Lpm) @ 60 psi

*Class II particle size: 1 um to <5 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

***Compliant for Lead reduction requirements under NSF/ANSl Standard 53 as tested by Pace Analytical Services, Inc.

(R_NSF is a registered trademark of NSF International.

Base Grille Water Filtration System

Model TIWG2LfT2RFWG2 Capacity 200 Gallons (758 Liters)

Model TlWG2/T2RFWG2 Capacity 200 Gallons (758 Liters)