KitchenAid KSRS25RSMK00, KSRS25CSWH00, KSRT25CRSS01, KSRW25CTMK00, KSRT25CRWH01 Owner’s Manual

Kitchen kid

REFRIGERATOR USE & CARE GUIDE

MANUAL DE USO Y CUIDADO DEL

REFRIGERADOR

GUIDE D'UTILISATION ET D'ENTRETIEN DU

p p

REFRIGERATEUR

Table of Contents / Indice / Table des matibres

ASSISTANCE OR SERVICE ............................ 1

REFRIGERATOR SAFETY ............................... 2

INSTALLATION INSTRUCTIONS ................... 3

REFRIGERATOR USE ..................................... 5

REFRIGERATOR CARE ................................... 8

TROUBLESHOOTING ...................................... 9

WATER FILTER CERTIFICATIONS .............. 11

PRODUCT DATA SHEETS ............................ 12

WARRANTY .................................................... 14

If you need assistance or service, first see the "Troubleshooting"
section. Additional help is available. Call us at 1-800-422-1230
from anywhere in the U.S.A., or write:

KitchenAid Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Information may also be obtained by visiting our website at

www.kitchenaid.com.
In Canada, for assistance, installation or service, call:

1-800-807-6777, or write:

KitchenAid Canada

Customer Interaction Centre

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

In Canada, visit www.KitchenAid.ca.

Please include a daytime phone number in your correspondence.
Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation
date for in-warranty service.

AYUDA O SERVICIO TF:CNICO .................... 15

SEGURIDAD DEL REFRIGERADOR ............ 15

INSTRUCCIONES DE INSTALACION .......... 16

USO DE SU REFRIGERADOR ...................... 19

CUIDADO DE SU REFRIGERADOR ............. 23

SOLUCION DE PROBLEMAS ....................... 24

HOJA DE DATOS DEL PRODUCTO ............ 27

GARANTiA ...................................................... 29

Assistance or Service

ASSISTANCE OU SERVICE .......................... 30

SleCURITle DU RleFRIGleRATEUR ................ 30

INSTRUCTIONS D'INSTALLATION .............. 31

UTILISATION DU RleFRIGleRATEUR ........... 34

ENTRETIEN DU RleFRIGleRATEUR ............. 38

DlePANNAGE .................................................. 39

FEUILLES DE DONNleES SUR

LE PRODUlT ................................................... 42

GARANTIE ...................................................... 42

Write down the following information about your appliance to help
you obtain assistance or service if you ever need it. You will need
to know your complete model number and serial number. You can
find this information on the model and serial number label, located

on the inside wall of the refrigerator compartment.

Dealer name
Serial number
Address
Phone number
Model number
Purchase date

Toorder replacement filters, call 1-800-442-9991 and ask for the
part number listed below or contact your authorized KitchenAid
dealer. In Canada, call 1-800-807-6777.

Stainless Steel Cleaner and Polish: Order Part #4396920
Standard Base Filter Cartridge:

Order Part #4396841 (T2RFWG2)
In Canada, Order Part #4396841B (T2RFWG2)

2318586

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured ifyou don't follow
instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,
away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of
your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily
climb inside.

INSTALLATION INSTRUCTIONS

) I_/'_¢ I< tI_ _ t_ _t_]o_'_o:1'

NOTE: It is recommended that you do not install the refrigerator
near an oven, radiator, or other heat source. Do not install in a
location where the temperature will fall below 55°F (13°C).

Excessive Weight Hazard

Use two or more people to move and install
refrigerator.

Failure to do so can result in back or other injury.

If the ice storage bin is located on the door, remove the
temporary shield from underneath the ice storage bin. See

"Ice Maker and Storage Bin."
Remove packaging materials. Do not use sharp instruments,

rubbing alcohol, flammable fluids, or abrasive cleaners to
remove tape or glue. These products can damage the surface

of your refrigerator. For more information, see "Refrigerator
Safety."

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator
for cleaning or service, be sure to protect the floor.
Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

ti

/

112"(1.25 crn)_

II -- _il

/

/

2" (5.08 cm)

.... I ..........

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,
fire, or electrical shock.

/

Explosion Hazard

Keep flammable materials and vapors, such as
gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for 1/2"
(1.25 cm) space on each side and at the top. When installing your
refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on

each side (depending on your model) to allow for the door to
swing open. If your refrigerator has an ice maker, allow extra
space at the back for the water line connections.

Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an
extension cord.

NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the control (Thermostat, Refrigerator or
Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you
are finished, reconnect the refrigerator to the electrical source and
reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

Gathertherequiredtoolsandpartsbeforestartinginstallation.
Readandfollowtheinstructionsprovidedwithanytoolslisted

here.

TOOLS NEEDED:

• Flat-blade screwdriver • 1/4"Drill bit

• 7/16"and 1/2"Open-end or two • Hand drill or electric drill
adjustable wrenches (properly grounded)

• 1/4"nut driver

NOTE: Your refrigerator dealer has a kit available with a 1/4"
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or 3/16"

(4.76 mm) saddle valve which reduces water flow and clogs more
easily.

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures will remain
above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and
120 psi (207 and 827 kPa) is required to operate the water
dispenser and ice maker. Ifyou have questions about your water
pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and
827 kPa).

If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill
after heavy usage.

• If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See "Water Filtration
System."

If you have questions about your water pressure, call a licensed,
qualified plumber.

..... ......S ,> ;?'

Read all directions before you begin.
IMPORTANT: If you turn the refrigerator on before the water line is

connected, turn the ice maker OFR

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.

4.

Determine the length of copper tubing you need. Measure
from the connection on the lower rear corner of the refrigerator

to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use
1/4"(6.35 mm) O.D. (outside diameter) copper tubing. Be sure
both ends of copper tubing are cut square.

5.

Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold
water pipe you have selected.

.......................A

G

B

'_'_ ...........................C

F E D v

A. Cold waterpipe E.Compressionsleeve
B.Pipe clamp F.Shutoff valve
C. Copper tubing G.Packing nut
D. Compression nut

6. Fasten shutoff valve to cold water pipe with pipe clamp. Be
sure outlet end is solidly in the 1/4"(6.35 mm) drilled hole in the
water pipe and that washer is under the pipe clamp. Tighten

packing nut. Tighten the pipe clamp screws slowly and evenly
so the washer makes a watertight seal. Do not overtighten or
you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw the compression
nut onto the outlet end with an adjustable wrench. Do not
overtighten.

8. Place the free end of the tubing into a container or sink, and
turn ON main water supply and flush out the tubing until water
is clear. Turn OFF the shutoff valve on the water pipe. Coil the

copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the shipping tape and the black nylon
plug from the gray, coiled water tubing on the rear of the

refrigerator.

3. If the gray water tube supplied with the refrigerator is not long
enough, a 1/4"x1/4"(6.35 mm x 6.35 mm) coupling is needed in
order to connect the water tubing to an existing household

water supply line. Thread the provided nut onto the coupling
on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.

3. Locate a 1/2"(12.70 mm) to 11/4'' (3.18 cm) vertical cold water
pipe near the refrigerator.

A B C D E F G

7

A. Refrigerator water tubing E.Ferrule (purchased)

B.Nut (provided) F Nut (purchased)

C.Bulb G.Household water line
D.Coupling (provided)

4.

Turn shutoff valve ON.

5.

Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the shipping tape and the black nylon
plug from the gray, coiled water tubing on the rear of the •

refrigerator.

3. Thread the provided nut onto the water valve as shown.
NOTE: Tighten the nut by hand. Then tighten it with a wrench •

two more turns. Do not overtighten.

I

IMPORTANT:

• Your product will not cool when the Refrigerator Control is set
to OFF.

The Refrigerator Control adjusts the refrigerator compartment
temperature. The Freezer Control adjusts the freezer
compartment temperature.

Wait 24 hours before you put food into the refrigerator. If you
add food before the refrigerator has cooled completely, your
food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a
higher (colder) than recommended setting will not cool the

compartments any faster.

_1|

A.Bulb
B.Nut (provided)

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.

Complete the Installation

Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.

Do not use an adapter.
Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Prepare the Water System" or
"Water and Ice Dispensers."

NOTE: It may take up to 24 hours for your ice maker to begin
producing ice.

A

B

REFRIGERATOR USE

Digital Controls

NOTE: The factory recommended set points are 0°F (-18°C) for

the freezer and 37°F (3°C) for the refrigerator.
To turn refrigerator on and view set points:

• Press and hold POWER (ON/OFF) pad for 2 seconds.

Warmer FREEZER REFRIGERATORWarmer

+

Colder Colder

To view the Celsius temperatures:

• Press the °C SELECT pad. The indicator will light up. To
redisplay degrees in Fahrenheit, press the °C SELECT pad
again.

NOTE: If the freezer temperature is below zero, the negative sign
next to the freezer display will light up.

Adjusting Controls

The settings indicated in the previous section should be correct
for normal household refrigerator usage. The controls are set

correctly when milk or juice is as cold as you like and when ice
cream is firm.

If you need to adjust temperatures in the refrigerator or freezer,
press the refrigerator or freezer PLUS (+) or MINUS (-) pad until

the desired temperature is reached. Use the settings listed in the
chart below as a guide. Wait at least 24 hours between
adjustments.

CONDITION/REASON: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR
Not set correctly for conditions Control 1° higher

REFRIGERATOR too warm REFRIGERATOR
High use or room very warm Control 1° lower

FREEZER too cold FREEZER Control
Not set correctly for conditions 1° higher

FREEZER too warm/too little ice FREEZER Control
High use or heavy ice use 1° lower

For your convenience, your refrigerator controls are preset at the
factory. When you first install your refrigerator, make sure that the

controls are still preset. The Refrigerator Control and the Freezer
Control should both be set to the "mid-settings."

Additional Control Panel Features

Chilled Door Bin Control

Additional features are located on the control panel at the top of
the refrigerator compartment.

Max Cool

The Max Cool feature assists with periods of heavy ice usage, full
grocery loads, or temporarily warm room temperatures.

• Press MAX COOL pad to turn on the Max Cool feature. The
Max Cool indicator light will remain on for 24 hours unless

manually turned off.
NOTE: The temperature display will not change. After

24 hours, the refrigerator returns to the previous temperature
set points.

Accelerated Ice Production (on some models)

This feature assists with temporary periods of heavy ice use by
increasing ice production over a 24-hour period.

• Press OPTIMICE ®feature touch pad to turn on the Optimlce °
feature. The Optimlce ®setting will remain on for 24 hours

unless manually turned off.

• If increased ice production is desired at all times, set the
Freezer Control to a colder number. Setting the freezer to a

colder temperature may make some foods, such as ice cream,
harder.

Temperature System

The Temperature System feature lets you know the compressor or
evaporator fan is running. It is normal for this indicator light to be

on.

Temperature

System

The control can be adjusted to properly chill meats or vegetables.
The air inside the pan is cooled to prevent "spot" freezing and can

be set to keep meats at the National Livestock and Meat Board
recommended storage temperatures of 28° to 32°F (-2° to 0°C).
The convertible vegetable/meat drawer control comes preset at

the lowest meat setting.

To store meat:

Set the control to one of the three MEAT settings to store meat at
its optimal storage temperature.

To store vegetables:

Set the control to VEG to store vegetables at their optimal storage
temperatures.

NOTE: If food starts to freeze, move the control to the left (less
cold). Remember to wait 24 hours between adjustments.

You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) for best storage of fruits and vegetables with skins.
HIGH (closed) for best storage of fresh, leafy vegetables.

*' .;9((

Cool air from the freezer is directed to the refrigerator door bin
directly beneath the vents.

NOTE: The dairy compartment and can rack are not associated
with the Chilled Door Bin feature.

The chilled door bin control is located on the left-hand side of the
refrigerator compartment.

A. Chilled door bin control

• Slide the door chill control to the left to reduce the flow of cold
air to the bin and make it less cold.

• Slide the door chill control to the right to increase the flow of
cold air to the bin and make it colder.

Depending on your model, your water and ice dispensers may
have one or more of the following features: a water level indicator

in the dispenser tray, a special light that turns on when you use
the dispenser, or a lock option to avoid unintentional dispensing.

NOTES:

• The dispensing system will not operate when the freezer door
is open.

• After connecting the refrigerator to a water source, flush the
water system by dispensing water into a sturdy container until
you draw and discard 1.5 gal. (5.4 L) of water, or for

approximately 3 minutes after the water begins dispensing.
The flushing process cleans the water system and clears air
from the lines. As the air is cleared from the lines, water may

spurt out of the dispenser.

• Allow 24 hours for the refrigerator to cool down and chill
water.

• Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.

The Water Dispenser

IMPORTANT: Dispense enough water every week to maintain a

fresh supply.

To Dispense Water:

1. Press a sturdy glass against the water dispenser pad.

NOTES:

• While dispensing water and for 3 seconds after dispensing

has stopped, the digital display will show how many
ounces of water have been dispensed.

• To switch from ounces to cups, press and hold ICE and

LOCKOUT at the same time until the dispenser beeps
after 3 seconds. To switch from cups to liters, press and

hold the buttons for another 3 seconds. To switch back to
ounces, repeat the process a third time.

2.

Remove the glass to stop dispensing.

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer when
the dispenser pad is pressed. The dispensing system will not

operate when the freezer door is open. To turn off the ice maker,
see "Ice Maker & Storage Bin."

Your ice maker can produce both crushed and cubed ice. The
display screen reads "CRUSHED" or "CUBED", indicating which

type is selected. To change the setting, press the ICE button
before dispensing ice.

For crushed ice, cubes are crushed before being dispensed. This
may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in size.
When changing from crushed to cubed, a few ounces of crushed
ice will be dispensed along with the first cubes.

To Dispense Ice:

1. If the ice storage bin is located on the door, remove the
temporary shield from underneath the ice storage bin. See

"Ice Maker and Storage Bin."

2. Press the button to select the desired type of ice.

Cut Hazard

Use a sturdy glass when dispensing ice.
Failure to de so can result in cuts.

The dispenser lights are LEDs that can not be changed. If it
appears that your dispenser lights are not working, be sure that

the light sensor is not blocked (in AUTO mode). See
"Troubleshooting" for more information.

The Dispenser Lock (on some models)

Your dispenser can be turned off for easy cleaning or to prevent
unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the product, to
the ice maker, or to the dispenser light. It simply deactivates the
ice and water dispensers. To turn off the ice maker, see "Ice

Maker & Storage Bin."

• Press and hold LOCKOUT for 3 seconds to lock the
dispenser. While the dispenser is locking, "LOCKING" will

appear on the display screen and the blue indicator light
around the LOCKOUT button will flash. When the dispenser is

locked, the indicator light will change to red for a few seconds,
then turn off.

Press and hold LOCKOUT a second time to unlock the
dispenser. While the dispenser is unlocking, "UNLOCKING"

will appear on the display screen and the red indicator light
around the LOCKOUT button will flash. When the dispenser is
unlocked, the indicator light will change to blue for a few
seconds, then turn off.

Turning the Ice Maker On/Off

Style 1:

The On/Off switch is located on the top right side of the freezer
compartment.

3. Press a sturdy glass against the ice dispenser pad. Hold the
glass close to the dispenser opening so ice does not fall
outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to the
pad in order to activate the ice dispenser. Pressing hard will

not make the ice dispense faster or in greater quantities.

4. Remove the glass to stop dispensing.
NOTE: Ice may continue to dispense for up to 10 seconds

after removing the glass from the pad. The dispenser may
continue to make noise for a few seconds after dispensing.

Dispenser Tray with Water Level Indicator
(on some models)

Your dispenser may include a small tray at the bottom of the
dispenser. It is designed to catch small spills and allow for easy

cleaning. The tray can be removed from the dispenser and carried
to the sink to be emptied or cleaned.

NOTE: There is no drain in the tray. When the tray is full of water
and needs to be emptied, a small red indicator pops up at the

back of the tray.

The Dispenser Light (on some models}

When you use the dispenser, the light will automatically turn on.
If you want the light to be on continuously, you may choose either

ON or AUTO.
ON: Press LIGHT to turn the dispenser light on.

AUTO: Press LIGHT a second time to select AUTO mode. The
dispenser light will automatically adjust to become brighter as the

room brightens, dimmer as the room darkens.
OFF: Press LIGHT a third time to turn the dispenser light off.

@

• To turn on the ice maker, slide the control to the ON (left)
position.

• To manually turn off the ice maker, slide the control to the
OFF (right) position.

Style 2:
The On/Off switch is located on the ice maker, behind the ice

maker cover door.

• To turn on the ice maker, flip the switch to the ON (top)
position.

• To manually turn off the ice maker, flip the switch to the
OFF (bottom) position.

NOTE: Your ice maker has an automatic shutoff. The ice maker
sensors will automatically stop ice production when the ice

storage bin is full or the freezer door is opened, but the control will
remain in the ON position.

REMEMBER:

• Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.

• The quality of your ice will be only as good as the quality of the
water supplied to your ice maker. Avoid connecting the ice
maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to
poor quality ice. If a softened water supply cannot be avoided,
make sure the water softener is operating properly and is well

maintained.

• Do not use anything sharp to break up the ice in the bin or
bucket. This can cause damage to the ice container and the
dispenser mechanism.

• Do not store anything on top of or in the ice maker or storage
bin.

Removing and Replacing Ice Storage Bin

1. Hold the base of the storage bin with both hands and press
the release button to lift the storage bin up and out.

NOTE: It is not necessary to turn the ice maker control to the
OFF position when removing the storage bin. The sensor
cover ("flipper door") on the left wall of the freezer stops the
ice maker from producing ice if the door is open or the storage
bin is removed.

2. Replace the storage bin on the door and push down to make
sure it is securely in place.

Non-indicator Water Filter (on some models)

If your refrigerator does not have the status light, you should
change the water filter every 6 months depending upon your

usage. If the water flow to the water dispenser or ice maker
decreases noticeably before 6 months have passed, replace the

water filter more often.

Changing the Water Filter

1. Press the eject button to release the filter from the base grille.

2. Pull the filter straight out.

3. Turn the cap counterclockwise to remove it from the filter.
IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

4. Align the ridge on the cap with the arrow on the new filter and
turn the cap until it snaps into place.

NOTE: You can run the dispenser without a filter. Your water
will not be filtered. Simply insert the cap all of the way into the

base grille and rotate the cap until it is firmly in place.

5. Remove the protective covers from the O-rings. Be sure the
O-rings are still in place after the covers are removed.

6. Push the filter into the base grille. The eject button will pop
back out when the filter is fully engaged.

7. Flush the water system. See "Water and Ice Dispensers."

Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or

I

after the system.

Water Filter Status Light (on some models)

The water filter status light and display screen help you know
when to change your water filter. Press the FILTER button to
check the status of your water filter.

If the filter is new:
You must press FILTER to view the filter's status. For a few

seconds, the status light will be blue and the display screen will
show what percentage of your filter's life remains.

If it is almost time to change the filter:
The status light will automatically illuminate and will remain on,

appearing yellow. The words "ORDER FILTER" will appear on the
display screen. Press FILTER to see what percentage of your
filter's life remains. You should order the appropriate replacement
filter. See "Accessories."

If it is time to change the filter:
The status light will remain on, changing to red. The words
"REPLACE FILTER" and "HOLD BUTTON TO RESET" will appear

on the display screen until the filter has been changed and the
status light has been reset.

To reset the water filter status light:
After changing the filter, reset the status light by pressing and

holding the FILTER button for 3 seconds. The status light will blink
red and change to blue, then turn off when the system is reset.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to prevent
odors from building up. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent
odor transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,
concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or
gaskets. Do not use paper towels, scouring pads, or other harsh
cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water.

4.

There is no need for routine condenser cleaning in normal
home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in
the home, the condenser should be cleaned every 2 to
3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Removethe base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

5.

Plug in refrigerator or reconnect power.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.

........... _>................

NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the
bulb with one of the same size, shape and wattage. On some
models, the dispenser light requires a heavy duty 10-watt bulb. All

other lights require a 40-watt bulb. Replacement bulbs are
available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable.
NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size,
shape and wattage.

4. Replace light shield when applicable.

5. Plug in refrigerator or reconnect power.

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.
Failure to follow these instructions can result in death,

fire, or electrical shock.

• Power cord unplugged? Plug into a grounded 3 prong outlet.

• Is outlet working? Plug in a lamp to see if the outlet is
working.

• Household fuse blown or circuit breaker tripped? Replace
the fuse or reset the circuit breaker. If the problem continues,

call an electrician.
Are controls on? Make sure the refrigerator controls are on.

See "Using the Controls."
New installation? Allow 24 hours following installation for the

refrigerator to cool completely.
NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its
high-efficiency compressor and fans. The unit may run even
longer if the room is warm, a large food load is added, doors are
opened often, or if the doors have been left open.

The refrigerator is noisy

Refrigerator noise has been reduced over the years. Due to this
reduction, you may hear intermittent noises from your new
refrigerator that you did not notice from your old model. Below are
listed some normal sounds with an explanation.

• Buzzing - heard when the water valve opens to fill the ice
maker

• Pulsating - fans/compressor adjusting to optimize
performance

• Rattling - flow of refrigerant, water line, or from items placed
on top of the refrigerator

• Sizzling/Gurgling - water dripping on the heater during
defrost cycle

• Popping - contraction/expansion of inside walls, especially
during initial cool-down

• Water running - may be heard when water melts during the
defrost cycle and runs into the drain pan

• Creaking/Cracking - occurs as ice is being ejected from the
ice maker mold.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct
position.

The doors are difficultto open

Explosion Hazard

Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.

Are the gaskets dirty or sticky? Clean gaskets with mild soap
and warm water.

The lights do not work

• Is a light bulb loose in the socket or burned out? See
"Changing the Light Bulbs."

• Is the dispenser light set to ON? The dispenser light will
operate only when the levers are pressed. If you want the
dispenser light to stay on continuously, set the dispenser light
to ON, or NIGHT LIGHT or AUTO. See "Water and Ice

Dispensers."

• Is the dispenser light set to NIGHT LIGHT or AUTO? If the
dispenser is set to the NIGHT LIGHT or AUTO mode, be sure

the dispenser light sensor is not blocked. See "Water and Ice
Dispensers."

Temperature is too warm

• New installation? Allow 24 hours following installation for the
refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter
refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for
refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions?
Adjust the controls a setting colder. Check temperature in
24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s} opened often or left open? Allows humid air to enter
refrigerator. Minimize door openings and keep doors fully
closed.

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch
(depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice

production.

• Large amount of ice recently removed? Allow 24 hours for
ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm?
Remove ice from the ejector arm with a plastic utensil.

• Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water pressure.

See "Water Supply Requirements" in either the Installation
Instruction booklet or the Use & Care Guide.

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff
valve fully open.

• Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.

• Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a
licensed, qualified plumber.

Off-taste, odor or gray color in the ice

• New plumbing connections? New plumbing connections
can cause discolored or off-flavored ice.

• Ice stored too long? Discard ice. Wash ice bin. Allow
24 hours for ice maker to make new ice.

• Odor transfer from food? Use airtight, moisture proof
packaging to store food.

• Are there minerals (such as sulfur) in the water? A water
filter may need to be installed to remove the minerals.

• Is there a water filter installed on the refrigerator? Gray or
dark discoloration in ice indicates that the water filtration

system needs additional flushing.

The ice dispenser will not operate properly

• If the ice storage bin is located on the door, remove the
temporary shield from underneath the ice storage bin. See

"Ice Maker and Storage Bin."

• Freezer door closed completely? Close the door firmly. If it
does not close completely, see "The doors will not close
completely."

• Ice bin installed correctly? Be sure the ice bin is firmly in
position.

• New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice
production.

• Ice stuck in the delivery chute? Use a plastic utensil to clear
the delivery chute.

• Has the wrong ice been added to the bin? Use only cubes
produced by the current ice maker.

• Has the ice melted around the auger (metal spiral} in the
ice bin? Empty the ice container. Use warm water to melt the
ice if necessary.

10

Cut Hazard

Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.

• Is the ice dispenser stalling while dispensing "crushed"
ice? Change the ice button from "crushed" to "cubed." If
cubed ice dispenses correctly, depress the button for
"crushed" ice and begin dispensing again.

• Has the dispenser arm been held in too long? Ice will stop
dispensing when the arm is held in too long. Wait 3 minutes
for dispenser motor to reset before using again.

The water dispenser will not operate properly

• Freezer door closed completely? Close the door firmly. If it
does not close completely, see "The doors will not close
completely."

• Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Is the water pressure at least 30 psi (207 kPa)? The water
pressure to the home determines the flow from the dispenser.

See "Water Supply Requirements."
Kink in the home water source line? Straighten the water

source line.
New installation? Flush and fill the water system.

Water filter installed on the refrigerator? The filter may be

clogged or incorrectly installed.
Is a reverse osmosis water filtration system connected to

your cold water supply? See "Water Supply Requirements"
in either the Installation Instructions or the Use & Care Guide.

Water is leaking from the dispenser

WATER FILTER

CERTIFICATIONS

State of Cahlbrnla

Department of Health Services

Water Treatment Device

Certificate Number

05- 1703

Date/_,aed: Apl_l 6, 2095

Dale Re_isex] Septemt_r 7, 2{19b

Trademark/Mode) Designation

Whirl[ Deluxe T2WG2

wh,_l, Deluxe "l 7WG?)

Toxaul _itc

RatedSer_iceCapaeity: 2G_)gals Rat_dSer_ieeFIow: 085gpm

D<>nol _ wi_ wa_r that is microhiologically unsafe or of imkno_ll quality, wit_ut ad_01ate disinfection h_fore ol ¸
after Ihe system¸

Conditions of Certificaaon:

State of California

Department of Health Services

WaterTreatment Device

CertificateNumber

05- 1702

Date Issued: April 6, 2005

[)ate RevKcah September 7. 2005

Replacement Element_

NOTE: One or two drops of water after dispensing is normal.

• Glass not being held under the dispenser long enough?
Hold the glass under the dispenser 2 to 3 seconds after

releasing the dispenser lever.

• New installation? Flush the water system. See "Prepare the
Water System" or "Water and Ice Dispensers."

• Recently changed water filter? Flush the water system. See
"Prepare the Water System" or "Water and Ice Dispensers."

The dispenser water is not cool enough

NOTE: Water from the dispenser is chilled to only 50°F (10°C).

• New installation? Allow 24 hours after installation for the
water supply to cool completely.

• Recently dispensed large amount of water? Allow 24 hours
for water supply to cool completely.

• Water not been recently dispensed? The first glass of water
may not be cool. Discard the first glass of water.

• Refrigerator connected to a cold water pipe? Make sure
the refrigerator is connected to a cold water pipe. See "Water
Supply Requirements."

Whirlpool DelnxeTIV4G2h

Manu[acturer: )

The water t_ Lto Section
116830 oft]

mid C6fita nl_
Ben_end

ca_bot_i'a_ ......

o-Diclild_obenz_n_ : .... [

Toxap_en_

23

RatedServiceCapacity: 200gals RatedServiceFlo_: (}5gpm

Do not use with water that is mlcr oblological)y unsafe or of unknown quality, without adequate" disinfection bcfi>le or
aher the syslem

Conditions of Certification:

11

PRODUCT DATA SHEETS

Base Grille Water Filtration System

Model T2WG2LfT2RFWG2 Capacity 200 Gallons (758 Liters)

Model T2WG2/T2RFWG2 Capacity 200 Gallons (758 Liters)

Tested and certified by NSF International against NSF/ANSI Standard 42
for the reduction of Chlorine Taste and Odor, Particulate Class I1"; and

against NSF/ANSI Standard 53 for the reduction of Mercury, Benzene,
Toxaphene, O-dichlorobenzene, and Carbofuran.

This system has been tested according to NSF/ANSl 42/53 for the reduction of the substances listed below. The concentration of the

indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water
leaving the system, as specified in NSF/ANSl 42/53.

Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %

Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction

Chlorine Taste/Odor 50% reduction 2.0182 mg/L 2.0 mg/L _+10% 0.06 mg/L ** 0.0536 mg/L 97.03 97.34
Particulate Class I1" 85% reduction 1333333 #/mL At east 10,000 part c es/mL 6600 #/mL 2325 #/mL 99.51 99.83

Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %
Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction

Lead: @ pH 6.5*** 0.010 mg/L 0.1533 mg/L 0.15 mg/L _+10% 0.0005 mg/L 0.0005 mg/L 99.67 99.67
Lead: @ pH 8.5*** 0.010 mg/L 0.1400 mg/L 0.15 mg/L _+10% 0.0007 mg/L 0.0006 mg/L 99.50 99.57

Mercury: @ pH 6.5 0.002 mg/L 0.0058 mg/L 0.006 mg/L _+10% 0.0002 mg/L 0.0002 mg/L 96.54 96.54
Mercury: @ pH 8.5 0.002 mg/L 0.0059 mg/L 0.006 mg/L _+10% 0.0005 mg/L 0.0003 mg/L 91.57 94.92

Benzene 0.005 mg/L 0.0154 mg/L 0.015 mg/L _+10% 0.0012 mg/L 0.0006 mg/L 92.22 96.34
O-Dichlorobenzene 0.6 mg/L 1.7571 mg/L 1.8 mg/L _+10% 0.0250 mg/L 0.0066 mg/L 98.58 99.63

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 mg/L _+10% 0.001 mg/L 0.001 mg/L 93.33 93.33

Carbofuran 0.04 mg/L 0.0819 mg/L 0.08 mg/L _+10% 0.0400 mg/L 0.0213 mg/L 51.13 74.00

Test Parameters: pH = 7.5 _+0.5 unless otherwise noted. Flow = 0.85 gpm (3.2 Lpm). Pressure = 60 psig (413.7 kPa).
Temp. = 68°F to 71.6°F (20°C to 22°C).

• It is essential that operational, maintenance, and filter
replacement requirements be carried out for the product to
perform as advertised.

• Use replacement cartridge T2RFWG2, part #4396841.
In Canada, use replacement cartridge T2RFWG2, part

#4396841 B. 2006 suggested retail price of $39.99 U.S.A./
$49.99 Canada. Prices are subject to change without notice.

Model T2WG2L: Style 1 - Press FILTER to check the status
of your water filter. If the filter indicator light is yellow, order a
new filter. If the filter indicator light is red, it is recommended
that you replace the filter.

Style 2 - When the filter indicator reads 10%, order a new
filter. When the filter indicator reads 0%, it is recommended

that you replace the filter.
Model T2WG2: Change the water filter cartridge every

6 months depending upon your usage. If the water flow to the
water dispenser or ice maker decreases noticeably before

6 months have passed, replace the water filter cartridge more
often.

• These contaminants are not necessarily in your water supply.
While testing was performed under standard laboratory

conditions, actual performance may vary.

• The product is for cold water use only.

• Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system.

• Refer to the "Assistance or Service" section for the
Manufacturer's name, address and telephone number.

• Refer to the "Warranty" section for the Manufacturer's limited
warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well
Water Pressure 30 - 120 psi (207 - 827 kPa)
Water Temperature 33 ° - 100°F (0.6 ° - 37.8°C)

Service Flow Rate 0.85 gpm (3.2 Lpm) @ 60 psi

*Class II particle size: 1 um to <5 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

***Compliant for Lead reduction requirements under NSF/ANSl Standard 53 as tested by Pace Analytical Services, Inc.

(R_NSF is a registered trademark of NSF International.

12

Base Grille Water Filtration System

Model TIWG2L/T2RFWG2 Capacity 200 Gallons (758 Liters)

Model TlWG2/T2RFWG2 Capacity 200 Gallons (758 Liters)

Tested and certified by NSF International against NSF/ANSI Standard 42
for the reduction of Chlorine Taste and Odor, Particulate Class II*; and

against NSF/ANSI Standard 53 for the reduction of Mercury, Benzene,
Toxaphene, O-dichlorobenzene, and Carbofuran.

This system has been tested according to NSF/ANSl 42/53 for the reduction of the substances listed below. The concentration of the

indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water
leaving the system, as specified in NSF/ANSl 42/53.

Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %

Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction

Chlorine Taste/Odor 50% reduction 2.0182 mg/L 2.0 mg/L _+10% 0.06 mg/L ** 0.0536 mg/L 97.03 97.34
Particulate Class II* 85% reduction 1333333 #/mL At east 10,000 part c es/mL 6600 #/mL 2325 #/mL 99.51 99.83

Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %
Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction

Lead: @ pH 6.5*** 0.010 mg/L 0.1533 mg/L 0.15 mg/L _+10% 0.0005 mg/L 0.0005 mg/L 99.67 99.67
Lead: @ pH 8.5*** 0.010 mg/L 0.1400 mg/L 0.15 mg/L _+10% 0.0007 mg/L 0.0006 mg/L 99.50 99.57

Mercury: @ pH 6.5 0.002 mg/L 0.0058 mg/L 0.006 mg/L _+10% 0.0002 mg/L 0.0002 mg/L 96.54 96.54
Mercury: @ pH 8.5 0.002 mg/L 0.0059 mg/L 0.006 mg/L _+10% 0.0005 mg/L 0.0003 mg/L 91.57 94.92

Benzene 0.005 mg/L 0.0154 mg/L 0.015 mg/L _+10% 0.0012 mg/L 0.0006 mg/L 92.22 96.34
O-Dichlorobenzene 0.6 mg/L 1.7571 mg/L 1.8 mg/L _+10% 0.0250 mg/L 0.0066 mg/L 98.58 99.63

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 mg/L _+10% 0.001 mg/L 0.001 mg/L 93.33 93.33

Carbofuran 0.04 mg/L 0.0819 mg/L 0.08 mg/L _+10% 0.0400 mg/L 0.0213 mg/L 51.13 74.00

Test Parameters: pH = 7.5 _+0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa).
Temp. = 68°F to 71.6°F (20°C to 22°C).

• It is essential that operational, maintenance, and filter
replacement requirements be carried out for the product to
perform as advertised.

• Use replacement cartridge T2RFWG2, part #4396841.
In Canada, use replacement cartridge T2RFWG2, part
#4396841 B. 2006 suggested retail price of $39.99 U.S.A./
$49.99 Canada. Prices are subject to change without notice.

Model TlWG2L: Style 1 - Press FILTER to check the status
of your water filter. If the filter indicator light is yellow, order a
new filter. If the filter indicator light is red, it is recommended
that you replace the filter.

Style 2 - When the filter indicator reads 10%, order a new
filter. When the filter indicator reads 0%, it is recommended
that you replace the filter.

Model TlWG2: Change the water filter cartridge every
6 months depending upon your usage. If the water flow to the

water dispenser or ice maker decreases noticeably before
6 months have passed, replace the water filter cartridge more

often.

• These contaminants are not necessarily in your water supply.
While testing was performed under standard laboratory
conditions, actual performance may vary.

• The product is for cold water use only.

• Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after

the system.

• Refer to the "Assistance or Service" section for the
Manufacturer's name, address and telephone number.

• Refer to the "Warranty" section for the Manufacturer's limited
warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well
Water Pressure 30 - 120 psi (207 - 827 kPa)

Water Temperature 33° - 100°F (0.6° - 37.8°C)
Service Flow Rate 0.5 gpm (1.9 Lpm) @ 60 psi

*Class II particle size: 1 um to <5 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

***Compliant for Lead reduction requirements under NSF/ANSl Standard 53 as tested by Pace Analytical Services, Inc.

(R_NSF is a registered trademark of NSF International.

13

KITCHENAID ®REFRIGERATOR WARILANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, KitchenAid or KitchenAid Canada (hereafter "KitchenAid") will pay for factory specified parts and repair labor to

correct defects in materials or workmanship. Service must be provided by a KitchenAid designated service company.
On models with a water filter: 30 day limited warranty on water filter. For 30 days from the date of purchase, when this filter is operated and

maintained according to instructions attached to or furnished with the product, KitchenAid will pay for replacement parts to correct defects in
materials and workmanship.

SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CAVITY LINER AND SEALED REFRIGERATION SYSTEM PARTS

In the second through fifth years from the date of purchase, when this major appliance is operated and maintained according to instructions
attached to or furnished with the product, KitchenAid will pay for replacement or repair of the refrigerator/freezer cavity liner (including labor

costs) if the part cracks due to defective materials or workmanship. Also, in the second through fifth years from the date of purchase,
KitchenAid will pay for factory specified parts and labor to correct defects in materials or workmanship in the sealed refrigeration system.
These parts are: compressor, evaporator, condenser, dryer, and connecting tubing. Service must be provided by a KitchenAid designated

service company.

SIXTH THROUGH TENTH YEAR LIMITED WARRANTY ON SEALED REFRIGERATION SYSTEM PARTS

In the sixth through tenth years from date of purchase, when this major appliance is operated and maintained according to instructions
attached to or furnished with the product, KitchenAid will pay for factory specified parts to correct defects in materials or workmanship in the

sealed refrigeration system. These parts are: compressor, evaporator, condenser, dryer, and connecting tubing.

LIFETIME LIMITED WARRANTY ON DOOR BINS AND CAN RACKS

For the life of the product, when this major appliance is operated and maintained according to instructions attached to or furnished with the
product, KitchenAid will pay for replacement of all SLIDE N LOCK TM Door Bins and SLIDE N LOCK TM Can Racks due to defective materials
or workmanship.

ITEMS KITCHENAID WILL NOT PAY FOR

1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair

house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters.

3. Repairs when your major appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance
with electrical or plumbing codes, or use of products not approved by KitchenAid.

5. Any food loss due to refrigerator or freezer product failures.

6. Replacement parts or repair labor costs for units operated outside the United States or Canada.

7. Pickup and delivery. This major appliance is designed to be repaired in the home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service in remote locations.

10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with published
installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIRAS PROVIDED HEREIN.
IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED

TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. KITCHENAID SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO

THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU
MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATETO STATEOR PROVINCE TO PROVINCE.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized KitchenAid dealer to determine if another
warranty applies.

Ifyou need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," additional help can be
found by checking the "Assistance or Service" section or by calling KitchenAid. In the U.S.A., call 1-800-422-1230. In Canada, call

1-800-807-6777. 1/06

14