KitchenAid KSRP25FNWH00, KSRS25CNLK00, KSRX22FNWH01, KSRX25FNWH01, KSRX25FNST01 Owner’s Manual

...

®itchen_kid ®

SIDE BY SIDE REFRIGERATOR

iJ i!!!i;:_ii!i!!_¸,,_:!i!il;:_i!;iilliii_iiiii_i_'_i:_!__i',iiiii_ii_iii__;::li_i!!_¸

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...

www.kitchenaid.com or www.KitchenAid.ca

REFRIGERATEUR COTE A COTE

Au Canada, pour assistance composez le 1-800-461-5681, pour installation ou service composez le 1-800-807-6777 ou visitez notre site web &...

www.KitchenAid.ca

Table of Contents/Table des matieres ............................................................................. 2

2305802

TABLE OF CONTENTS

TABLE DES MATIERES

REFRIGERATOR SAFETY ............................................................. 3

Proper Disposal of Your Old Refrigerator .................................... 3

INSTALLATION INSTRUCTIONS .................................................. 4

Unpack the Refrigerator ............................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 5

Water Supply Requirements ........................................................ 5

Base Grille .................................................................................... 5

Refrigerator Doors ........................................................................ 6

Adjust the Doors ........................................................................... 7

Connect the Water Supply ........................................................... 8

Prepare the Water System ........................................................... 9

Factory Trim Kit ............................................................................ 9

Normal Sounds .......................................................................... 11

REFRIGERATOR USE .................................................................. 11

Ensuring Proper Air Circulation .................................................. 11

Using the Controls ..................................................................... 11

Water and Ice Dispensers .......................................................... 13

Water Filter Status Light ............................................................. 15

Water Filtration System .............................................................. 15

Ice Maker and Storage Bin ........................................................ 16

REFRIGERATOR FEATURES ...................................................... 17

Refrigerator Shelves ................................................................... 17

Deli Drawer ................................................................................. 17

Convertible Vegetable/Meat Drawer, Crisper and Covers ........17

Convertible Vegetable/Meat Drawer Temperature Control ....... 18

Crisper Humidity Control ........................................................... 18

Wine Rack .................................................................................. 18

Utility Bin .................................................................................... 18

FREEZER FEATURES .................................................................. 18

Freezer Shelf .............................................................................. 18

Freezer Basket or Bin ................................................................. 19

DOOR FEATURES ........................................................................ 19

Tilt-out Freezer Door Bin ............................................................ 19

Snap-on Freezer Door Bin ......................................................... 19

Drop-in Door Rails...................................................................... 19

Can Racks and Door Bins .......................................................... 19

Door Air Control ......................................................................... 19

REFRIGERATOR CARE ............................................................... 20

Cleaning ...................................................................................... 20

Changing the Light Bulbs ........................................................... 20

Power Interruptions .................................................................... 21

Vacation and Moving Care ......................................................... 21

TROUBLESHOOTING .................................................................. 22

ASSISTANCE OR SERVICE ......................................................... 25

In the U.S.A ................................................................................ 25

In Canada ................................................................................... 25

Accessories ................................................................................ 25

WATER FILTER CERTIFICATIONS ............................................. 25

PRODUCT DATA SHEETS ........................................................... 26

WARRANTY .................................................................................. 27

SI:!:CURIT¢:DU RI:!:FRIGC:RATEUR.............................................. 28

Mise au rebut de votre vieux refrigerateur ................................. 28

INSTRUCTIONS D'INSTALLATION ............................................. 29

Deballage du refrigerateur .......................................................... 29

Emplacement d'installation ........................................................ 29

Specifications electriques .......................................................... 30

Specifications de I'alimentation en eau ..................................... 30

Grille de la base .......................................................................... 30

Portes du refrigerateur ............................................................... 31

Ajuster les portes ........................................................................ 32

Raccordement de la canalisation d'eau .................................... 33

Preparer le systeme d'eau ......................................................... 34

Ensembles decoratifs de I'usine ................................................ 34

Sons normaux ............................................................................ 36

UTILISATION DU RI_FRIGI:!:RATEUR.......................................... 36

Pour s'assurer d'une circulation d'air appropriee ...................... 36

Utilisation des commandes ........................................................ 37

Distributeurs d'eau et de gla(_ons.............................................. 39

Le temoin lumineux de I'etat du filtre a eau............................... 41

Syst_me de filtration d'eau ........................................................ 41

Machine a glagons et bac d'entreposage ................................. 42

CARACTI:!:RISTIQUES DU RC:FRIGC:RATEUR ........................... 43

Tablettes du refrigerateur ........................................................... 43

Tiroir pour specialites alimentaires ............................................ 43

Tiroir & legumes/viande convertible,

bac a legumes et couvercles ..................................................... 44

Reglage de la temperature du tiroir

legumes/viande convertible ....................................................... 44

Reglage de I'humidite dans le bac a legumes ........................... 44

Casier a vin ................................................................................. 45

Casier utilitaire ............................................................................ 45

CARACTI:!:RISTIQUES DU CONGI_LATEUR ............................... 45

Tablette de congelateur ............................................................. 45

Panier ou bac de congelateur .................................................... 45

CARACTI_RISTIQUES DE LA PORTE ......................................... 45

Compartiment inclinable de la porte du congelateur ................ 45

Compartiment encliquetable de la porte du congelateur .......... 46

Tringles deposees dans la porte ................................................ 46

Porte-cannettes et balconnets ................................................... 46

Commande d'air de la porte ...................................................... 46

ENTRETIEN DU RI_FRIGI_RATEUR ............................................ 46

Nettoyage ................................................................................... 46

Remplacement des ampoules d'eclairage ................................ 47

Pannes de courant ..................................................................... 48

Entretien avant les vacances ou Iors d'un demGnagement .......48

DI_PANNAGE ................................................................................. 49

ASSISTANCE OU SERVICE ......................................................... 53

Accessoires ................................................................................ 53

FEUILLES DE DONNI_ES SUR LE PRODUIT ............................. 54

GARANTIE ..................................................................................... 55

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

mPlug into a grounded 3 prong outlet, m Use nonflammable cleaner. mDo not remove ground prong. mDo not use an adapter.

mDo not use an extension cord. mDisconnect power before servicing.

mReplace all panels before operating. mRemove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

m Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

m Use two or more people to move and install refrigerator. m Disconnect power before installing ice maker (on ice maker

kit ready models only).

m Use a sturdy glass when dispensing ice or water (on some

models).

Proper Disposal of Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of your old refrigerator, please follow these instructions to help

prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily climb inside.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging Materials

• Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information see "Refrigerator Safety."

When _,_ovieg Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pulI the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions in "Refrigerator Care."

_mportant information to know about glass shemves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble=size pieces. This is normal. Glass shelves and covers are heavy. Use specia! care when removing them to avoid impact from dropping.

Expmosion Hazard

Keep flammable materials and vapors, such as gasomine, away from refrigerator.

Faimureto do so can resumt in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on each side (depending on your model) to allow for the door to swing open. If your refrigerator has an ice maker, allow extra space at the back for the water line connections.

NOTE: Do not install the refrigerator near an oven, radiator, or other heat source, nor in a location where the temperature will fall below 55°F (13°C).

_Jl,

112"(1.25 crn):

II -- ]

2" {5.08 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these }nstructions can result }n death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15 or 20 amp fused, grounded

electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord. NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.

Water Pressure

A cold water supply with water pressure of between 30 and 120 psi (207 - 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 - 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 - 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If your refrigerator has a water filter cartridge, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter cartridge. See "Water Filtration System."

If you have questions about your water pressure, call a licensed, qualified plumber.

Read all directions carefully before you begin.

IMPORTANT:

• If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

TOOLS NEEDED: Fiat-blade screwdriver, 7/16"and 1/2"open-end

wrenches or two adjustable wrenches, 1/4"nut driver and drill bit, hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/16"

(4.76 mm) saddle valve which reduces water flow and clogs more easily.

Remove the Base Grille:

1. Open both doors.

2. Place hands along the ends of the grille. Push in on the top of the base grille and pull up on the bottom.

NOTE: Be sure to refasten the Tech Sheet behind the base grille after cleaning.

Replace the Base Grille:

1. Open both doors.

2. Line up the grille support tabs with the metal clips.

3. Push the grille firmly to snap it into place.

TOOLSNEEDED:1/4",1/2",and%6"hex-headsocketwrenches,afiat-bladescrewdriverandaPhillipsscrewdriver,

IMPORTANT:Beforeyoubegin,turntherefrigeratorcontrolOFEUnplugrefrigeratorordisconnectpower.Removefoodandany adjustabledoororutilitybinsfromdoors,

ElectricamShockHazard

Disconnect power before removing doors. Reconnect both ground wires before operating, Failure to do so can result in death or electrical shock.

Top Left Hinge

A. Do Not Remove Screw

A. Red Outer Ring

Door RemovaJ

o_ooo

Top Right Hinge

A. Do Not Remove Screw

Bottom Hinge

A. Do Not Remove Screw

Door AJignment

A J

A. Leveling Screw

EiectricamShockHazard

Disconnect power before removing doors,

Faimureto do so can resumt in death or eiectricam shock,

1. Unplug refrigerator or disconnect power.

2. Open both refrigerator doors. Remove the base grille by pulling up on the bottom outside corners. See Graphic 1.

3. Close both doors and keep them closed until you are ready to lift them free from the cabinet.

4. If you have a dispenser (ice or water), disconnect the water dispenser tubing located behind the base grille on the freezer

door side. See Graphic 2.

• Press the red outer ring against the face of fitting and pull

the dispenser tubing free.

• On some models, remove tubing from hose clip.

5. Remove top left hinge screw and cover as shown in Graphic 3.

6. Disconnect wiring plug and both ground wires from the ground wire screw (on some models) as shown in Graphic 3.

7. Remove remaining left hinge screws and hinge as shown in Graphic 3. Do not remove screw A.

8. Carefully lift freezer door straight up off bottom hinge. See Graphic 4. The water dispenser tubing remains attached to

the freezer door and pulls through the bottom left hinge. Make sure you protect the dispenser tubing from damage.

9. Remove top right hinge cover and screws as shown in Graphic 5. Do not remove screw A.

f0. Lift the refrigerator door straight up off bottom hinge. f 1. It may not be necessary to remove the bottom hinge to move

the refrigerator through a doorway. Both bottom hinges have similar construction.

• Disassemble the hinges as shown in Graphic 6.

Do not remove screw A.

Replace the Doors and Hinges

f. Replace both bottom hinges, if removed. Tighten screws.

2. Assistance may be needed to feed the water dispenser tubing through the bottom hinge while reinstalling the freezer

door. Carefully feed the dispenser tubing through the bottom left hinge before replacing the door on the hinge.

NOTE: Provide additional support for the doors while the top hinges are being replaced. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Reconnect water dispenser tubing by pushing tubing into fitting until it stops and black mark touches the face of the red

outer ring. See Graphic 2. On some models, replace tubing in hose clip.

Electrical Shock Hazard

Reconnect both ground wires. Failure to do so can result in death or electrical shock.

Style 1

• Reconnect both ground wires.

• Reconnect wiring plug.

A.Do notremove screw A B.Ground wires

C.Greenground wire screw D.Wiring plug

Style 2

• Reconnect wiring plug.

5. Replace left hinge cover and screws.

6. Replace the refrigerator door by carefully lifting the door onto the bottom right hinge.

7. Align and replace the top right hinge as shown in Graphic 5. Tighten screws.

8. Replace hinge cover and screws. Tighten screws.

9. Plug into a grounded 3 prong outlet.

Your refrigerator has two front adjustable rollers -- one on the right and one on the left. If your refrigerator seems unsteady or if you want the doors to close more easily, adjust the refrigerator's tilt using the instructions below:

f. Move the refrigerator into its final position.

2. The two leveling screws are part of the front roller assemblies which are at the base of the refrigerator on either side. See Graphic 7.

3. Use a hex-head socket wrench to adjust the leveling screws. Turn the leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. It may take several turns of the leveling screws to adjust the tilt of the refrigerator. See Graphic 7.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.

4. Openbothdoorsagainandchecktomakesurethatthey closeaseasilyasyoulike.Ifnot,tilttherefrigeratorslightly moretotherearbyturningbothlevelingscrewstotheright.It maytakeseveralmoreturns,andyoushouldturnboth levelingscrewsthesameamount.

5. Replacethebasegrille.

NOTE:BesuretorefastentheTechSheetbehindthebasegrille.

Readalldirectionsbeforeyoubegin. IMPORTANT:Ifyouturntherefrigeratoronbeforethewaterline

isconnected,turntheicemakerOFF.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a 1/2"(12.70 mm) to 11/4'' (3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of the

refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold water pipe you have selected.

...................A

G ..............................B

.............. C

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. A 1/4"x 1/4"coupling is needed to order to connect the water tubing to an existing household water supply line. Thread the provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

B c

A.Refrigerator water tubing B.Nut (provided)

C.Bulb

Turn shutoff valve ON.

Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

6. Plug in refrigerator or reconnect power.

7. Flush the water system see "Prepare the Water System."

NOTE: It may take up to 24 hours for your ice maker to begin producing ice.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown. NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

D E F

D.Coupling (provided)

E.Ferrule (purchased) F Nut (purchased)

A.Cold water pipe E.Compression sleeve B.Pipe clamp F.Shutoff valve C.Copper tubing G.Packing nut D. Compression nut

6. Fasten shutoff valve to cold water pipe with pipe clamp. Be sure outlet end is solidly inthe 1/4"(6.35 mm) drilled hole in the water pipe and that washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw the compression nut onto the outlet end with an adjustable wrench. Do not overtighten.

8. Place the free end of the tubing into a container or sink, and turn ON main water supply and flush out the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

A.Bulb B.Nut (provided)

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

6. Plug in refrigerator or reconnect power.

7. Flush the water system. See "Prepare the Water System."

NOTE: It may take up to 24 hours for your ice maker to begin producing ice.

}!!:__i;!_z!i!ii?';_i!_i__i¸x!_i:!ii_i_i_::!!'ii,'V,s_!ii:eY!!i!!i¸,}_s__i:e_i_i:i__i_i_

Please read before using the water system. Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker. For Style f, lift up the wire shutoff arm as shown. For Style 2, move the switch to the OFF (right) setting as shown. The ON/OFF switch is located on the top right side of the freezer compartment.

Style I

Style 2

NOTES:

• If your model has a base grille filter system, make sure the base grille filter is properly installed and the cap is in the horizontal position.

• Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before or after the system.

Use a sturdy container to depress the water dispenser bar until the water begins to flow. Flush the water system by dispensing and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take approximately 6 to 7 minutes and will help clear air from the line. Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

Open the freezer door and turn on the ice maker. For Style 1, lower the wire shutoff arm. For Style 2, move the switch to the ON (left) position. Please refer to the "Ice Maker and Storage Bin" section for further instructions on the operation of your ice maker.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

• Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

There may be an occasion when you will need to remove the factory-installed trim kit, such as moving the refrigerator to a new home or installing custom-made decorator panels. Please read all instructions carefully before removing the trim kit and decorator panels.

Freezer Door Refrigerator Door

B A

.......................C .........................

A. Decorator panels

B. Filler panels C. Handles

Remove the Door Panels

NOTE: When removing and replacing decorator panels, only the

handle is removed. All other trim pieces remain attached to the doors.

1. Remove the refrigerator and freezer handles:

• Using a Phillips screwdriver, remove the screws that hold each handle in place.

• Lift off handle. Make sure you keep screws for reattaching handles.

2. Remove the door panels:

• Open refrigerator or freezer door.

• Slide out decorator panel and filler board.

• Repeat process for other panels and filler boards.

• Store panel and filler boards carefully to prevent scratching.

Replace the Door Panels

1. Replace the refrigerator or freezer door panels:

• Open refrigerator or freezer door.

• Carefully slide the 1/8"(3.18 mm) decorator panel into place behind the side trim.

• Push the filler board into place behind the decorator panel.

• Repeat process for other panels and filler boards.

2. Attach the handles: NOTE: Freezer door handle is notched to fit around the

dispenser panel.

• Align the top of the refrigerator or freezer handle flush

with the top trim. Fasten the handle to the refrigerator or freezer door with the screws, using a Phillips screwdriver.

• Repeat the process for the other handle.

Dimensions for Custom Wood Panels:

22 cu. ft Freezer and Refrigerator door

1/4"

(6.35 mm)

21=

127/16""_

1,6 cm)

6011/64"

(154.2 cm)

1/4"

(6.35 rnm)

5/16 '_

17.93 mm)

I(50,7 cm)

Care for Decorator Panels

1. Clean panels with an anti-static cleaner (available in electronics or computer departments) or mild soap and water

with a clean, soft, damp cloth.

2. Rinse panels thoroughly and blot dry using a dry, soft cloth or chamois.

NOTE: Do not use paper towels or cleaners which contain solvents such as ammonia. They can damage the surface of the panels.

3. If small scratches should appear on the panels, they may be filled using an automotive paste wax (not a cleaner/wax

combination). Apply wax sparingly and buff lightly with a clean, soft cloth using a circular motion.

Install Custom Wood Panels

If you plan to install custom wood decorator panels, you will need

to create the panels yourself or consult your cabinetmaker or

carpenter. See dimensional drawings for wood panel inserts.

Flat panels:

You can create a custom flat panel a maximum of 1/4"(6.35 mm)

thick to replace your decorator panels. Flat wood panels less than 1/4"(6.35 mm) thick are not recommended.

Raised panels:

A raised panel design can be created by screwing or gluing wood

panels to 1/4"(6.35 mm) backing or by using 3/4"(19.05 mm) stock with routed edges.

Weight requirements for raised panel inserts:

• Refrigerator door panel should not exceed 25 Ibs.

(9.98 kg).

• Freezer door panels should not exceed 18 Ibs. (6.80 kg)

combined weight.

5/16" /

(7,93 mm)Q_

265/64 _'

(71,3 crn)

(6.35 ram)

3V4" _14"min. _14"

82,86mmrain. 19,08mmrain._19,05mrn_

TOP VIEW "_

25 cu. ft Freezer and Refrigerator door

1/4"

(6.35 mm)

!1;f_2Cm)

I I I I

L .... ,I

_ 153/16"._

(38,6 cm)

631¼6 ''

_153A6,, H (161.6 cm)

(38,6 cm)

28s/o4,,

(71,3 cm)

5/16"

114"

(6,35ram)

5/16"

[7.93 mm)

5/16"

(7,93 mm)

(

%" rnin. 31/4"

(19,05mmmin.) (8255rnrnmin) .-}?'

(6.36 ram)

'................ ' Du.ubmm)

TOP VIEW

1/4"

(6,35 mm)

31/4" _/,_"min. _/4"

82,55mmmin. 19,05rnmmin._19,06mm_

_ TOP VIEW _ _

(6.35 mm)

1/4"

(6.35ram)

Dimensions for Routing Handle Side of Door Panel (End View)

Route entire areas of handleside of panels31/4''(8.25 cm).

31/4"

(8.25 crn)

rnin. _ I Hinge Side

]

-(3

V4"(6.35ram)max. Panel Panel

Door Doer

° 'l !2

2" (5 cm) 1"

min. (2,54 cm)

Your new refrigerator may make sounds that your old one didn't make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder. The following describes the kinds of sounds and what may be making them.

• If your product is equipped with an ice maker, you will hear a buzzing sound when the water valve opens to fill the ice maker for each cycle.

Your refrigerator is designed to run more efficiently to keep your food items at the desired temperatures and to minimize energy usage. The high efficiency compressor and fans may cause your refrigerator to run longer than your old one. You may also hear a pulsating or high-pitched sound from the compressor or fans adjusting to optimize performance.

• You may hear the evaporator fan motor circulating air through the refrigerator and freezer compartments. The fan speed may increase as you open the doors or add warm food.

• Rattling noises may come from the flow of refrigerant, the water line, or items stored on top of the refrigerator.

• Water dripping on the defrost heater during a defrost cycle may cause a sizzling sound.

• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your refrigerator.

• Contraction and expansion of the inside walls may cause a popping noise.

• You may hear air being forced over the condenser by the condenser fan.

• You may hear water running into the drain pan during the defrost cycle.

REFRIGERATOR USE

In order to ensure proper temperatures, you need to permit air to flow between the two sections. Cold air enters the bottom of the

freezer section and moves up. It then enters the refrigerator section through the top vent. Air then returns to the freezer as

shown.

Do not block any of these vents with food such as soda, cereal, bread, etc. If the vents are blocked, airflow will be prevented and the temperature controls will not function properly.

IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent odor transfer from food, wrap or cover foods tightly.

Your model may have Slide Controls, Electronic Controls or Digital Controls.

IMPORTANT (All Controls):

• The Refrigerator control adjusts the refrigerator compartment temperature. The Freezer control adjusts the freezer

compartment temperature.

• Wait 24 hours after you turn on the refrigerator before you put food into it. If you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the Refrigerator and Freezer controls to a lower (colder) setting will not cool the compartments any

faster.

• If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

• The preset settings should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

Slide Controls (on some models)

For your convenience, your controls are preset at the factory. When installing your refrigerator, make sure that the controls are still preset to the "mid-settings" as shown.

Style 1

Freezer Refrigerator

C )

cold I 2 ,= 3 4 colder off I 2 ,= 3 4 colder

Style 2

Freezer Refrigerator

Off I 2 • 3 4 Colder Cold I 2 • 3 4 Colder

IMPORTANT:

• For Style 1, your product will not cool when the Refrigerator control is set to OFE For Style 2, your product will not cool

when the Freezer Control is set to OFE Settings to the left of the mid-setting make the temperature

less cold. Settings to the right of the mid-setting make the temperature colder.

The Automatic Exterior Moisture control continuously guards against moisture buildup on the outside of your refrigerator cabinet. This control does not have to be set or adjusted.

Adjusting Slide Controls

NOTE: Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

If you need to adjust temperatures:

• Slide the FREEZER or REFRIGERATOR control, one setting to the right or left depending on the needed temperature change.

NOTE: For Style 1, after adjusting the refrigerator temperature, wait 24 hours and then recheck the FREEZER temperature before making additional adjustments.

CONDITION: SETTING ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Control Not set correctly for conditions one setting lower

REFRIGERATOR too warm REFRIGERATOR Control High use or room very warm one setting higher

FREEZER too cold FREEZER Control one Not set correctly for conditions setting lower

FREEZER too warm/too little ice FREEZER Control one High use or heavy ice usage setting higher

Electronic Controls (on some models)

If you need to adjust temperatures:

• Press the FREEZER or REFRIGERATOR arrow to move the indicator light to the right, one setting at a time. Continue

moving the indicator light until it is at the desired setting.

=oo.oo.,,

NOTE: With each press of the arrow, you will hear a beep as the light moves to the next setting. The indicator light moves to a setting of "7" and then returns to the setting of "1 ."

CONDITION: SETTING ADJUSTMENT: REFRIGERATOR too cold REFRIGERATOR Control

Not set correctly for conditions one setting lower REFRIGERATOR too warm REFRIGERATOR Control

High use or room very warm FREEZER too cold FREEZER Control one

Not set correctly for conditions setting lower FREEZER too warm/too little ice FREEZER Control one

High use or heavy ice usage setting higher

Additional Electronic Control Panel Features

Additional features are located on the control panel at the top of the refrigerator compartment.

(_ 5 6 7 _

one setting higher

Water Filter Indicator Light and Reset

See "Water Filter Status Light."

Accelerated Ice Production

This feature assists with temporary periods of heavy ice usage by increasing ice production over a 24-hour period.

• Press ICE touch pad to set the freezer temperature to -10°F (-23°C). The Accelerated Ice setting will remain on for 24 hours unless manually turned off. The display will continue to show your normal temperature set point.

For your convenience, your controls are preset at the factory. When installing your refrigerator, make sure that the controls are still preset to the "mid-settings" as shown.

FREEZER

2 3 @ 5 6 7

To turn on refrigerator:

• Press and hold ON/OFF for 2 seconds. The indicator lights show the current temperature control settings.

NOTE: Settings to the left of the mid-setting make the temperature less cold. Settings to the right of the mid-setting make the temperature colder.

Adjusting Electronic Controls

NOTE: Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

REFRIGERATOR

COLD COLDER

1 2 3 (_) 5 6 7

If increased ice production is desired at all times, set the Freezer Control to a colder setting. Adjusting the freezer to a colder temperature may make some foods, such as ice cream, harder.

Digital Controls (on some models)

For your convenience, your controls are preset at the factory. When installing your refrigerator, make sure that the controls are

still preset to the "mid-settings" as shown. The digital control panel is located at the top of the refrigerator compartment.

NOTE: The factory recommended set points are 0°F (-18°C) for the freezer and 37°F (3°C) for the refrigerator.

To turn refrigerator on and view set points:

• Press and hold POWER (ON/OFF) pad for 2 seconds.

Warmer

Power

On/Off

Colder

FREEZER REFRIGERAIORWarmer

i!i m

Colder

To view the Celsius temperatures:

• Press the °C SELECT pad. The indicator will light up. To redisplay degrees in Fahrenheit, press the °C SELECT pad again.

°c

NOTE: If the freezer temperature is below zero, the negative sign next to the freezer display will light up.

Adjusting Digital Controls

NOTE: Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made. To adjust set point temperatures:

• Press the refrigerator or freezer PLUS (+) or MINUS (-) pad until the desired temperature is reached.

I_EFRI®ERA_Ior_ Warmer

Accelerated Ice Production (on some models)

This feature assists with temporary periods of heavy ice use by increasing ice production over a 24-hour period.

• Press OPTIMICE touch pad to turn on the Optimlce ®feature. The Optimlce ®setting will remain on for 24 hours unless manually turned off.

If increased ice production is desired at all times, set the Freezer Control to a colder number. Setting the freezer to a colder temperature may make some foods, such as ice

cream, harder.

Temperature System

The Temperature System feature lets you know the compressor or evaporator fan is running. It is normal for this indicator light to

be on.

Colder

The set point range for the freezer is -5°F to 5°F (-21 °C to -15°C). The set point range for the refrigerator is 33°F to 41 °F

1°C to 5°C).

CONDITION/REASON: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Control 1° Not set correctly for conditions higher

REFRIGERATOR too warm REFRIGERATOR Control 1° High use or room very warm

lower

FREEZER too cold FREEZER Control 1° higher Not set correctly for conditions

FREEZER too warm/too little FREEZER Control 1° lower ice

High use or heavy ice use

Additional Digital Control Panel Features

Additional features are located on the control panel at the top of the refrigerator compartment.

Water Filter Indicator Light and Reset

See "Water Filter Status Light."

Max Cool

The Max Cool feature assists with periods of heavy ice usage, full

grocery loads, or temporarily warm room temperatures.

• Press MAX COOL pad to turn on the Max Cool feature. The Max Cool indicator light will remain on for 24 hours unless manually turned off.

Cool

NOTE: The temperature display will not change. After 24 hours, the refrigerator returns to the previous temperature set points.

Temperature

System

Cut Hazard

Use a sturdy gBase when dispensing ice or water. Faimureto do so can reeumt in cuts.

Depending on your model, you may have one or more of the following options: the ability to select either crushed or cubed ice, a special light that turns on when you use the dispenser, a special AUTO mode, or a lock option to avoid unintentional dispensing.

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer. When the dispenser lever is pressed:

• A trap door opens in a chute between the dispenser and the ice bin. Ice moves from the bin and falls through the chute.

• When you release the dispenser lever, the trap door closes and the ice dispensing stops. The dispensing system will not operate when the freezer door is open.

Some models dispense both cubed and crushed ice. Before dispensing ice, select which type of ice you prefer. The button controls are designed for easy use and cleaning.

Style 1 Style 2

c_ n

Crushed Cubed

ICE

CRUSH CUBE

For crushed ice, cubes are crushed before they are dispensed.

This may cause a slight delay when dispensing crushed ice.

Noise from the ice crusher is normal, and pieces of ice may vary in size. When changing from crushed to cubed, a few ounces of crushed ice will be dispensed along with the first cubes.

To Dispense Ice:

1. Press button for the desired type of ice.

2. Press a sturdy glass against the ice dispenser lever. Hold the glass close to the dispenser opening so ice does not fall outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to the lever in order to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.

Remove the glass to stop dispensing. NOTE: The first few batches of ice may have an off-flavor

from new plumbing and parts. Throw the ice away. Also, take large amounts of ice from the ice bin, not through the dispenser.

The Water Dispenser

If you did not flush the water system when the refrigerator was first installed, press the water dispenser bar with a sturdy glass or jar until you draw and discard 2 to 3 gal. (8 to 12 L) or

approximately 6 to 7 minutes of water after water begins

dispensing. It will take 3 to 4 minutes for the water to begin

dispensing. The water you draw and discard cleans the system

and helps clear air from the lines. Allow several hours for the

refrigerator to cool down and chill water.

IMPORTANT: Depending on your model, the small removable tray at the bottom of the dispenser is designed to catch small

spills and allow for easy cleaning. There is no drain in the tray. The tray can be removed from the dispenser and carried to the

sink to be emptied or cleaned.

The Dispenser Light

Style 1 The dispenser area has a light. It can be turned on manually by

pressing the ON button (touch pad or rocker switch). On some models: Whenever you use the dispenser the lever will

automatically turn the light on.

LIGHT

OFF ON

NOTE: See "Changing the Light Bulbs" for information on changing the dispenser light bulb.

Style 2

When you use the dispenser, the lever will automatically turn the light on. If you want the light to be on continuously, you may

choose either ON or AUTO.

On Auto

LIGHT

ON: Press the LIGHT button to turn the dispenser light on. AUTO: Press the LIGHT button a second time to select the AUTO

mode. The dispenser light will automatically adjust to become brighter as the room brightens, dimmer as the room darkens.

OFF: Press the LIGHT button a third time to turn the dispenser light off.

The dispenser lights are LEDs which should not need to be changed. If it appears that your dispenser lights are not working, check to be sure that the light sensor is not blocked (in AUTO mode). See "Troubleshooting" for more information.

To Dispense Water:

1. Press a sturdy glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

NOTE: Water may have an off-flavor if you do not use the

dispenser periodically. Dispense enough water every week to

maintain a fresh supply.

The Dispenser Lock (on some models)

Your dispenser can be turned off for easy cleaning or to prevent unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator, to the ice maker, or to the dispenser light. It simply deactivates the dispenser levers.

Style 1

Toturn off the dispenser, press the LOCK button until the indicator appears. The ice and water dispensers will not work. To unlock the dispenser, press the UNLOCK button until the indicator appears. Then continue to dispense ice or water as

usual.

DISPENSER

LOCK UNLOCK

Style 2

To turn off the dispenser, press and hold the LOCK OUT button

until the indicator appears. The ice and water dispensers will not

work. To unlock the dispenser, press the LOCK OUT button until the indicator disappears. Then continue to dispense ice or water

as usual.

Lockout

Remove the cartridge cap by sliding it off the end of the old cartridge. The cap will slide to the left or right. Do not discard the cap.

Press &

HoUcl

iO_ _i_O_¸ _ _-_O_

The water filter status light will help you know when to change your water filter cartridge. The light will change from green to yellow. This tells you that it is almost time to change the water filter cartridge (90% of the filter life has been used). It is

recommended that you replace the base grille water filter

cartridge when the water filter indicator light changes to red OR

water flow to your water dispenser or ice maker decreases

noticeably. To change the base grille water filter cartridge, see

"Changing the Water Filter Cartridge" later in this section. After changing the water filter cartridge, reset the water filter

status light.

Style 1

Press the light switch 5 times within 10 seconds. The status light

will change from red to green.

A. Status light B. Light switch

Style 2

Press and hold the water filter reset button until the status light turns green. Your reset button may be located on the water

dispenser or on the control panel in the refrigerator compartment.

Dispenser Control Panel

O Light Sensor

-_ FilterIndicator ,.X

Ydlow _ Order ¢ Wafer Red : Replace eOrder Filter

Press &

HoUd

Green = Good OGood •

OChange

(Reset)

Take the new cartridge out of its packaging and remove protective cover from O-rings.

Slide the cartridge cap onto the new cartridge. See illustration in Step 2.

With cartridge cap in the vertical position, push the new filter cartridge into the base grille until it stops. Rotate the cartridge

cap clockwise to a horizontal position. Flush the water system. See "Flushing the Water System After Replacing

Filter" section.

Flushing the Water System After Replacing Filter

households. NOTE: As air is cleared from the system, water may spurt out of

the dispenser.

Using the Dispenser Without the Water Filter Cartridge

You can run the dispenser without a water filter cartridge. Your water will not be filtered.

Remove the base grille water filter cartridge. Slide the cartridge cap off the end of the filter cartridge. Do

not discard the cap. With the cartridge cap in the vertical position, insert the cap into the base grille until it stops.

< i

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system.

Changing the Water Filter Cartridge

Locate the water filter cartridge cap in the front base grille. Rotate the cap counterclockwise to a vertical position and pull the cap and filter cartridge out through the base grille.

NOTE: There will be water in the cartridge. Some spilling may

occur.

3. Rotate the cartridge cap to a horizontal position. The cartridge cap might not be even with the base grille.

!O¸i _i¸ _ii_O__ii!_i!¸iii_;i_b_i__ii!_ii!!!!_= _!_iO:i:!_i!_!_i_Oi_i_? )¸

Style 1

To Turn the Ice Maker On/Off:

The on/off switch for the ice maker is a wire shutoff arm located

on the side of the ice maker.

1. To turn the ice maker on, simply lower the wire shutoff arm. NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position.

2. To manually turn the ice maker off, lift the wire shutoff arm to the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate.

2. To manually turn the ice maker off, slide the control to the OFF (right) position.

To Remove and Replace the Ice Storage Bin:

1. Hold the base of the storage bin with both hands and press

the release button to lift the storage bin up and out. NOTE: It is not necessary to turn the ice maker control to the

OFF (right) position when removing the storage bin. The sensor cover ("flipper door") on the left wall of the freezer stops the ice maker from producing ice if the door is open or the storage bin is removed.

2. Replace the storage bin on the door and push down to make sure it is securely in place.

To Remove and Replace Ice Storage Bin:

1. Pull the covering panel out from the bottom and then slide it back toward the rear.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position. Ice can still be dispensed, but no more can be made.

3. Lift up the front of the storage bin and pull it out.

4. Replace the bin by pushing it in all the way or the dispenser will not work. Push the wire shutoff arm clown to the ON

position to restart ice production. Make sure the door is closed tightly.

Style 2

To Turn the Ice Maker On/Off:

The ON/OFF switch is located on the top right side of the freezer

compartment.

1. To turn the ice maker on, slide the control to the ON (left) position.

NOTE: Your ice maker has an automatic shutoff. The ice maker sensors will automatically stop ice production, but the

control will remain in the ON (left) position.

Clean the Ice Storage Bin

Empty the ice container. Use warm water to melt the ice if necessary.

NOTE: Never use anything sharp to break up the ice in the bin. This can cause damage to the ice container and the dispenser mechanism.

2. Wash ice bin with a mild detergent, rinse well and dry thoroughly. Do not use harsh or abrasive cleaners or solvents.

Remember

• Allow 24 hours to produce the first batch of ice. Allow 3 days to completely fill ice container.

• Discard the first three batches of ice produced to avoid impurities that may be flushed out of the system.

• The quality of your ice will be only as good as the quality of the water supplied to your ice maker.

Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

• It is normal for the ice cubes to be attached at the corners. They will break apart easily.

• For Style I ice maker, do not force the wire shutoff arm up or down.

• Do not store anything on top of the ice maker or in the ice storage bin.

REFRIGERATOR FEATURES

Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories" section.

_mportant information to know about gBaes sheBves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

Your model may have glass or wire shelves. Store similar foods

together and adjust the shelves to fit different heights. This

reduces the time the refrigerator door is open and saves energy.

Slide-out Shelves (on some models}

The dell drawer stores raisins, nuts, spreads, and other small items at normal refrigerator temperatures.

To Remove and Replace the Deli Drawer:

1. Remove the dell drawer by sliding it straight out to the stop. Lift the front and slide the drawer out the rest of the way.

2. Replace the dell drawer by sliding it back past the stop.

Crisper and Convertible Vegetable Meat Drawers

To Remove and Replace a Shelf in a Metal Frame:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up

and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding it back into the slots on the frame and pushing the shelf in past the stop.

Shelves and Shelf Frames

To Remove and Replace a Shelf/Frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into the shelf supports. Tilt the front of the shelf up until rear shelf hooks drop into the shelf supports. Check to make sure that the shelf is securely in position.

1. Slide crisper or meat drawer straight out to the stop. Lift the front of drawer with one hand while supporting the bottom of

drawer with other hand and slide the drawer out the rest of the way.

2. Replace the crisper or meat drawer by sliding it back in fully past the drawer stop.

Crisper or Vegetable/Meat Drawer Covers

To Remove and Replace Covers:

1. Remove the crisper and meat drawer. Press up in center of crisper glass insert until it rises above the plastic frame. Holding the crisper glass firmly, carefully slide the glass insert

forward to remove.

2. Lift crisper cover frame and remove. Repeat steps to remove the meat drawer cover.

3. Replace back of meat drawer cover frame into supports or slides on side walls of the refrigerator and lower or slide the front of the cover frame into place.

4. Slide rear of glass insert into cover frame and lower front into place. Repeat steps to replace the crisper cover.

+ 39 hidden pages