THANK YOU for purchasing this high-quality product. Register your range at www.kitchenaid.com. In Canada, register your range
at www.kitchenaid.ca.
For future reference, please make a note of your product model and serial numbers. These can be found on the label located on the oven
frame behind the top-right side of the oven door.
Model Number______________________________________________ Serial Number_______________________________________________
Para una versión de estas instrucciones en español, visite www.kitchenaid.com.
Deberá tener a mano el número de modelo y de serie, que están ubicados en el marco del horno, detrás del lado derecho superior
de la puerta del horno.
Table of Contents
RANGE SAFETY .............................................................................2
The Anti-Tip Bracket ....................................................................3
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
WARNING: If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
follow instructions.
You
can be killed or seriously injured if you don't
instructions.
follow
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
•
Do not touch any electrical switch.
•
Do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
•
instructions.
If you cannot reach your gas supplier, call the fire department.
•
– Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
2
The Anti-Tip Bracket
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without having
the anti-tip bracket fastened down properly.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Verify the anti-tip bracket has been properly installed and engaged per installation instructions.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:
Anti-Tip
Bracket
Range Foot
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor or wall.
• Slide range back so rear range foot is under anti-tip bracket.
• See installation instructions for details.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock,
injury to persons, or damage when using the range, follow
basic precautions, including the following:
■ WARNING: TO REDUCE THE RISK OF TIPPING OF
THE RANGE, THE RANGE MUST BE SECURED BY
PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK
IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE
RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET
SECURELY ATTACHED TO FLOOR OR WALL, AND
SLIDE RANGE BACK SO REAR RANGE FOOT IS UNDER
ANTI-TIP BRACKET.
■
WARNING:
heater to heat or warm the room. Doing so may result in
carbon monoxide poisoning and overheating of the oven.
■ WARNING: NEVER cover any slots, holes or passages
in the oven bottom or cover an entire rack with materials
such as aluminum foil. Doing so blocks air flow through the
oven and may cause carbon monoxide poisoning.
Aluminum foil linings may also trap heat, causing a fire
hazard.
■ CAUTION: Do not store items of interest to children in
cabinets above a range or on the backguard of a range –
children climbing on the range to reach items could be
seriously injured.
NEVER use this appliance as a space
Proper Installation – The range, when installed, must be
■
electrically grounded in accordance with local codes or, in
the absence of local codes, with the
Code, ANSI/NFPA 70
electrically grounded in accordance with Canadian
Electrical Code. Be sure the range is properly installed and
grounded by a qualified technician.
This range is equipped with a three-prong grounding plug
■
for your protection against shock hazard and should be
plugged directly into a properly grounded receptacle. Do
not cut or remove the grounding prong from this plug.
■ Disconnect power before servicing.
Injuries may result from the misuse of appliance doors or
■
drawers such as stepping, leaning, or sitting on the doors
or drawers.
■ Maintenance – Keep range area clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
■ Storage in or on the Range – Flammable materials should
not be stored in an oven or near surface units.
■ Top burner flame size should be adjusted so it does not
extend beyond the edge of the cooking utensil.
For self-cleaning ranges –
■ Before Self-Cleaning the Oven – Remove broiler pan and
other utensils. Wipe off all excessive spillage before
initiating the cleaning cycle.
. In Canada, the range must be
National Electrical
SAVE THESE INSTRUCTIONS
3
BE
D
A
KEY USAGE TIPS
AquaLift® Self-Cleaning Technology
AquaLift® Self-Cleaning Technology is a first-of-its-kind cleaning
solution designed to minimize the time, temperature, and odors
that ordinarily come with traditional self-cleaning methods. With
AquaLift® Self-Cleaning Technology, an exclusive coating on the
interior of the oven is activated with heat and water to release
baked-on soil. To use AquaLift® Self-Cleaning Technology, simply
wipe out loose debris, pour water into the oven bottom, and run
the AquaLift® Self-Cleaning cycle. When the cycle finishes in under
1 hour at a lower temperature than in traditional self-cleaning
methods, just wipe out the remaining water and loose debris.
See the “Clean Cycle” section for more detailed instructions. For
additional information, frequently asked questions, and videos
on using AquaLift® Self-Cleaning Technology, visit our website at
http://whirlpoolcorp.com/aqualift.
Surface Temperatures
When the range is in use, all range surfaces may become hot such
as the knobs and oven door.
Baking Drawer
When the oven is in use, the drawer may become hot. Do not store
plastics, cloth, or other items that could melt or burn in the drawer.
A
C
A. Small (S)
B. X-Large (XL)
Align the gas tube opening in the burner base with the orifice
holder on the cooktop and the igniter electrode with the notch in
the burner base.
C. Medium (M)D. Medium (M)
E. Large (L)
A
B
C
E
D
Oven Vent
The oven vent releases hot air and moisture from the oven and
should not be blocked or covered. Do not set plastics, paper, or
other items that could melt or burn near the oven vent.
Preheating
When beginning a Bake or Convect Bake, the oven will begin
preheating after Start is pressed. The oven will take approximately
12 to 15 minutes to reach 350°F (177°C) with all of the oven
racks provided with your oven inside the oven cavity. Higher
temperatures will take longer to preheat. The preheat cycle rapidly
increases the oven temperature. The actual oven temperature
will go above your set temperature to offset the heat lost when
your oven door is opened to insert food. This ensures that when
you place your food in the oven, the oven will begin at the proper
temperature. Insert your food when the preheat tone sounds. Do
not open the door during preheat before the tone sounds.
Surface Burners
The burner bases and caps must be properly positioned before
cooking. Your range comes with three sizes of burners and caps.
Each round burner base is marked with a letter indicating the
burner size. Align the burner bases as shown in the following
illustration:
A. Burner cap
B. Gas tube opening
C. Burner base
Place the burner caps on the appropriate burner bases. Each
round burner cap is marked with a letter indicating the burner size.
Place the burner caps on the appropriate burner bases.
Small cap (S) Medium cap (M) Large cap (L)X-Large cap (XL)
Burner caps should be level when properly positioned. If burner
caps are not properly positioned, surface burners will not light. The
burner cap should not rock or wobble when properly aligned.
A. Incorrect
B. Correct
D. Igniter electrode
E. Orifice holder
B
4
FEATURE GUIDE
This manual covers several models. Your model may have some or all of the items listed. Refer to this manual or the Product Help section
of our website at www.kitchenaid.com for more detailed instructions. In Canada, refer to the Product Help Section at www.kitchenaid.ca.
WARNING
Food Poisoning Hazard
Do not let food sit for more than one hour before or
after cooking.
Doing so can result in food poisoning or sickness.
KeypadFeatureInstructions
CLOCK/TOOLSClock
CLOCK/TOOLSSettings
OVEN LIGHTOven cavity light
TIMER SET/OFFOven timer
STARTCooking start
CANCEL UPPER
CANCEL LOWER
(on some models)
BAKE Baking and
Range function
roasting
The Clock can use a 12- or 24-hour cycle. See the “Electronic Oven Controls” section.
1. Press CLOCK/TOOLS until “CLOCK” is displayed.
2. Use the number keypads to set the time of day.
3. Press START to change the time.
4. Press “3” for AM or “6” for PM.
Enables you to personalize the audible tones and oven operation to suit your needs.
See the “Electronic Oven Controls” section.
The oven light is controlled by a keypad on the oven control panel. While the oven
door is closed, press OVEN LIGHT to turn the light On and Off. When the oven door is
opened, the oven light will automatically come On.
The Timer can be set in hours or minutes up to 9 hours and 59 minutes.
1. Press TIMER SET/OFF.
2. Press the number keypads to set the length of time in hr-min-min. Leading zeros
do not have to be entered. For example, for 2 minutes, enter “2.”
3. Press TIMER SET/OFF to begin the countdown. If enabled, end-of-cycle tones will
sound at end of countdown.
4. Press TIMER SET/OFF again to cancel the Timer and return to the time of day.
Do not press the Cancel keypad because the oven will turn off.
5. If the Timer is running but not in the display, press TIMER SET/OFF to display the
countdown for 5 seconds.
The Start keypad begins any oven function. If Start is not pressed within 2 minutes after
pressing a keypad, the function is canceled and the time of day is displayed.
The Cancel keypad stops any function for the appropriate oven or drawer, except
the Clock and Timer.
1. Press BAKE.
2. Set the desired temperature between 170°F and 500°F (75°C and 260°C) using the
number keypads. The default temperature is 350°F (180°C).
3. Press START.
4. To change the temperature, repeat steps 2 and 3.
5. Press CANCEL UPPER when finished.
5
KeypadFeatureInstructions
STEAM BAKESteam bake
BROILBroiling
PROOFProofing bread
KEEP WARMHold warm
EASY CONVECT
BAKE
EASY CONVECT
BROIL
Convection
cooking
Convection
cooking
1. Insert the steam rack with water reservoir in the oven.
2. Pour 11/2 cups (350 mL) of warm water into the water reservoir.
NOTE: Do not fill past the MAX mark.
3. Press STEAM BAKE.
4. Press the number keypad to select the desired food option.
5. Press the number keypads to set the temperature.
6. Press START.
7. Insert food when preheating finishes.
8. (Optional) Press COOK TIME. Press the number keypads to set the cook time.
9. Press START.
10. Press CANCEL UPPER when finished.
NOTE: Let oven cool before removing and emptying water reservoir.
1. Press BROIL.
2. Press the number keypads to set the desired temperature.
3. Press START and allow the oven to preheat for 2 minutes.
4. To change the temperature, repeat steps 2 and 3.
5. Position the cookware in the oven, and then close the door.
6. Press CANCEL UPPER when finished.
1. Place prepared dough in oven. Press PROOF.
2. Press START.
Let the dough rise until nearly doubled in size. Proofing time may vary depending
on dough type and quantity.
3. Press CANCEL UPPER when finished proofing.
Refer to the “Proofing Bread” section for more information.
Food must be at serving temperature before placing it in the warmed oven.
1. Press KEEP WARM.
2. Set the desired temperature between 145°F and 190°F (63°C and 88°C) using the
number keypads. The default temperature is 170°F (75°C).
3. Press START.
4. Press CANCEL UPPER when finished.
1. Press EASY CONVECT BAKE.
2. Press “1” to have the oven automatically convert the temperature and time for
convection baking. Press “2” to manually convert the temperature and time.
3. Press the number keypads to set a temperature other than 325°F (177°C) in 5°
increments between 170°F and 500°F (77°C and 260°C).
4. Press START.
5. To change the temperature, repeat steps 3 and 4.
6. Press CANCEL UPPER when finished.
1. Press EASY CONVECT BROIL.
2. Press “1” to have the oven automatically convert the temperature and time for
convection baking. Press “2” to manually convert the temperature and time.
3. Press the number keypads to set a temperature other than 450°F (232°C) in
5° increments between 300°F and 500°F (149°C and 260°C).
4. Press START.
5. To change the temperature, repeat steps 3 and 4.
6. Press CANCEL UPPER when finished.
6
KeypadFeatureInstructions
EASY CONVECT
ROAST
COOK TIMETimed cooking
DELAY STARTDelayed start
BAKING DRAWER
BAKE
(on some models)
BAKING DRAWER
SLOW COOK
(on some models)
BAKING DRAWER
KEEP WARM
(on some models)
AQUALIFT SELF
CLEAN
START
(Hold 3 Sec)
CLOCK/TOOLSEnergy save
Convection
cooking
Baking drawer
Slow cook
drawer
Warming drawer
Clean cycle
Oven control
lockout
1. Press EASY CONVECT ROAST.
2. Press “1” to have the oven automatically convert the temperature and time for
convection baking. Press “2” to manually convert the temperature and time.
3. Press the number keypads to set a temperature other than 325°F (177°C)
in 5° increments between 170°F and 500°F (77°C and 260°C).
4. Press START.
5. To change the temperature, repeat steps 3 and 4.
6. Press CANCEL UPPER when finished.
Timed cooking allows the oven to be set to turn on at a certain time of day, cook for
a set length of time, and/or shut off automatically.
To set a Timed Cook or a Delayed Timed Cook, see the “Cook Time” section.
The Delay Start keypad is used to enter the starting time for an oven function with
a delayed start. Delay Start should not be used for foods such as breads and cakes
because they may not bake properly.
To set a Timed Cook or a Delayed Timed Cook, see the “Cook Time” section.
1. Press BAKING DRAWER BAKE.
2. Set the desired temperature between 170°F and 451°F (75°C and 233°C) using the
number keypads. The default temperature is 350°F (180°C).
3. Press START.
4. To change the temperature, repeat steps 2 and 3.
5. Press CANCEL LOWER when finished.
1. Press BAKING DRAWER SLOW COOK.
2. Set the desired temperature between 190°F and 250°F (88°C and 121°C) using the
number keypads. The default temperature is 190°F (88°C).
3. Place the food(s) in the baking drawer.
4. Press START.
5. (Optional) Set the desired cook time using the number keypads.
6. Press START to begin heating the baking drawer.
7. Press CANCEL LOWER when finished.
Food must be at serving temperature before placing it in the warmed oven.
1. Press BAKING DRAWER KEEP WARM.
2. Set the desired temperature between 145°F and 190°F (63°C and 88°C) using the
number keypads. The default temperature is 170°F (75°C).
3. Press START.
4. Press CANCEL LOWER when finished.
See the “Clean Cycle” section.
1. Check that the oven is OFF.
2. Press and hold START (Hold 3 Sec) for 3 seconds.
3. A tone will sound, and “Control Locked” will scroll, and then “Locked” will be displayed.
4. Repeat to unlock. No keypads will function with the controls locked. The cooktop
functions are not affected by the oven control lockout.
1. Press CLOCK/ TOOLS until “ENERGY SAVE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press CANCEL to exit and display the time of day.
If Energy Save is ON, the range will go into Sleep mode after 5 minutes of inactivity.
Any keypad press will activate the display. If Energy Save is OFF, the display will be
ON at all times.
7
Electronic Oven Controls
Control Display
The display will flash when powered up or after a power loss.
Press CANCEL UPPER to clear. When the oven is not in use, the
time of day is displayed. If the range is in Energy Save mode, the
display will be blank when not in use.
Tones
Tones are audible signals, indicating the following:
One Tone
■ Valid keypad press
■ Oven is preheated (long tone).
■ Function has been entered.
■ Reminder, repeating each minute after the end-of-cycle tones
Three Tones
■ Invalid keypad press
Four Tones
■ End-of-cycle
Use the Clock/Tools keypad to change the tone settings.
Energy Save
The Energy Save mode puts the range into Sleep mode and
reduces energy consumption.
To Activate the Energy Save Mode:
1. Press CLOCK/TOOLS until “ENERGY SAVE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press CANCEL to exit and display the time of day.
5. The setting will be activated after 5 minutes.
To Deactivate the Energy Save Mode:
1. Press CLOCK/TOOLS until “ENERGY SAVE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press CANCEL to exit and display the time of day.
5. The clock will reappear in the display and the range can be
operated as usual.
Settings
Many features of the oven control can be adjusted to meet your
personal needs. These changes are made using the Clock/Tools
keypad.
Use the Clock/Tools keypad to scroll through the features that can
be changed. Each press of the Clock/Tools keypad will advance
the display to the next setting. After selecting the feature to be
changed, the control will prompt you for the required input. Then
press START or CANCEL UPPER to exit and display the time
of day. Details of all of the feature changes are explained in the
following sections.
Press CANCEL UPPER to exit Settings.
Clock
The Clock can use a 12- or 24-hour cycle.
1. Press CLOCK/TOOLS until “CLOCK” is displayed.
2. Use the number keypads to set the time of day.
3. Press START to change the time.
4. Press “3” for AM or “6” for PM.
Fahrenheit and Celsius
The temperature is preset to Fahrenheit but can be changed
to Celsius.
1. Press CLOCK/TOOLS until “TEMP UNIT” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
Audible Tones Disable
Turns off all tones, including the end-of-cycle tone and keypress
tones. Reminder tones are still active when all tones are disabled.
1. Press CLOCK/TOOLS until “SOUND” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
Sound Volume
Sets the volume of the tone to either high or low.
1. Press CLOCK/TOOLS until “SOUND VOLUME” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
End-of-Cycle Tone
Activates or turns off the tones that sound at the end of a cycle.
1. Press CLOCK/TOOLS until “END TONE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
Keypress Tones
Activates or turns off the tones when a keypad is pressed.
1. Press CLOCK/TOOLS until “KEYPRESS TONE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
Reminder Tones Disable
Turns off the short repeating tone that sounds every 1 minute after
the end-of-cycle tones.
1. Press CLOCK/TOOLS until “REMINDER TONE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
12/24 Hour Clock
1. Press CLOCK/TOOLS until “12/24 HOUR” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
8
Loading...
+ 17 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.