KitchenAid KRBL102ESS, KRBR102ESS, KRBL109ESS, KRBR109ESS, MBL1957FEZ Owner's Manual

...

BOTTOM-MOUNT REFRIGERATOR OWNER’S

MANUAL

MANUEL D’UTILISATION DU RÉFRIGÉRATEUR AVEC

CONGÉLATEUR EN BAS

Table of Contents/Table des matières

REFRIGERATOR SAFETY.................................................2

Refrigerator Safety......................................................... 2

MAINTENANCE AND CARE ..............................................3

Cleaning ......................................................................3

Changing the LED Module ............................................... 3

Water Filtration System ...................................................3

Vacation and Moving Care ...............................................4

INSTALLATION INSTRUCTIONS ........................................ 4

Unpack the Refrigerator .................................................. 4

Electrical Requirements ..................................................5

Location Requirements ...................................................5

Water Supply Requirements.............................................5

Connect the Water Supply ...............................................6

REFRIGERATOR FEATURES............................................. 7

Crisper Humidity Control ................................................. 7

DOOR AND HANDLE INSTRUCTIONS ................................ 7

Refrigerator Doors and Drawer ......................................... 7

Remove and Replace Door Handles .................................. 7

Remove Doors and Hinges .............................................. 9

Reverse Doors (optional)............................................... 11

Replace Doors and Hinges ............................................ 11

Remove and Replace Freezer Drawer.............................. 13

PERFORMANCE DATA SHEET ........................................ 15

SÉCURITÉ DU RÉFRIGÉRATEUR .................................... 17

Sécurité du réfrigérateur................................................ 17

ENTRETIEN ET RÉPARATION ......................................... 18

Nettoyage .................................................................. 18

Remplacer le module à DEL........................................... 19

Système de filtration de l’eau.......................................... 19

Précautions à prendre avant les vacances ou le

déménagement ........................................................... 19

INSTRUCTIONS D’INSTALLATION ................................... 20

Déballage du réfrigérateur ............................................. 20

Spécifications électriques .............................................. 20

Exigences d’emplacement ............................................. 21

Spécifications de l’alimentation en eau ............................. 21

Raccordement à la canalisation d’eau .............................. 21

CARACTÉRISTIQUES DU RÉFRIGÉRATEUR..................... 23

Réglage de l’humidité dans le tiroir à légumes .................... 23

INSTRUCTIONS POUR LA PORTE ET LA POIGNÉE............ 23

Portes et tiroir du réfrigérateur ........................................ 23

Consulter la section Retrait et réinstallation des poignées de

porte ......................................................................... 24

Démontage des portes et charnières................................ 25

Inversion des portes (facultatif) ....................................... 27

Réinstallation des portes et charnières ............................. 28

Retrait et réinstallation du tiroir de congélation ................... 30

FICHE DE DONNÉES RELATIVES AU RENDEMENT ........... 32

W11479841A

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These

words mean:

You can be killed or seriously injured if you don't

DANGER

immediately follow instructions.

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

You can be killed or seriously injured if you don’t follow instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions,

including the following: � Children should be supervised to ensure that they do not

play with the appliance.

� This appliance is not intended for use by persons (including

children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

� Do not use an extension cord. � If power supply cord is damaged, it must be replaced by the

manufacturer, its service agent, or a similarly qualified person in order to avoid a hazard.

� Connect to potable water supply only.

� This appliance is intended to be used in household and

similar applications such as: staff kitchen areas in shops, offices, and other working environments; farm houses and by clients in hotels, motels, and other residential-type environments; bed and breakfast-type environments; and catering and similar non-retail applications.

� Do not store explosive substances such as aerosol cans

with a flammable propellant in this appliance.

� Do not use replacement parts that have not been

recommended by the manufacturer (e.g., parts made at home using a 3D printer).

� Keep the ventilation openings, in the appliance enclosure

or in the built-in structure, clear of obstruction.

� Do not use mechanical devices or other means to

accelerate the defrosting process, other than those recommended by the manufacturer.

� Do not damage the refrigerant circuit. � Do not use electrical appliances inside the food storage

compartments of the appliance, unless they are of the type recommended by the manufacturer.

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

WARNING: Risk of child entrapment. Before you throw away your old refrigerator or freezer:

� Take off the doors. � Leave the shelves in place so that children may not easily

climb inside.

WARNING

Suffocation Hazard Remove doors or lid from your old appliance. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous, even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with federal and local regulations. Refrigerants must be evacuated by a licensed, EPA-certified refrigerant technician in accordance with established procedures.

MAINTENANCE AND CARE

Cleaning

WARNING

Explosion Hazard Risk of Fire or Explosion. Flammable Refrigerant Used. Do Not Use Mechanical Devices to Defrost Refrigerator. Do Not Puncture Refrigerant Tubing.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid odor buildup. Wipe up spills immediately.

IMPORTANT:

� Because air circulates between both sections, any odors

formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To avoid odor transfer and drying out of food, wrap or cover foods tightly.

� For stainless steel models, stainless steel is corrosion-

resistant and not corrosion-proof. To help avoid corrosion of your stainless steel, keep your surfaces clean by using the following cleaning instructions.

To Clean Your Refrigerator: NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, muriatic acid, cleaning waxes, concentrated detergents, bleaches, or cleansers containing petroleum products on exterior surfaces (doors and cabinet), plastic parts, interior, and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand-wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

3. Clean the exterior surfaces. Painted metal: Wash painted metal exteriors with a clean,

soft cloth or sponge and a mild detergent in warm water. Rinse surfaces with clean, warm water and dry immediately to avoid water spots.

Stainless steel: Wash stainless steel surfaces with a clean, soft cloth or sponge and a mild detergent in warm water. Rinse surfaces with clean, warm water and dry immediately to avoid water spots.

NOTE: When cleaning stainless steel, always wipe with the grain to avoid cross-grain scratching.

WARNING

Explosion Hazard

Risk of Fire or Explosion due to Puncture of Refrigerant Tubing;

Follow Handling Instructions Carefully. Flammable Refrigerant Used.

4. There is no need for routine condenser cleaning in normal

home operating environments. If the environment is particularly greasy or dusty, or there is a significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

If you need to clean the condenser: � Pull refrigerator out away from the wall. See “Unpack the

Refrigerator.”

� Remove the base grille. � Vacuum coils when they are dusty or dirty. � Replace the base grille when finished. � Roll refrigerator back into place. Make sure to leave 1"

(2.5 cm) between the cabinet back and the wall.

� Check to see that the refrigerator is level.

5. Plug in refrigerator or reconnect power.

Changing the LED Module

IMPORTANT: The lights in both the refrigerator and freezer

compartments use LED technology that do not need to be replaced.

If an LED module(s) do not illuminate when the refrigerator and/or freezer door is opened, call for assistance or service. See "Quick Start Guide" for contact information.

Water Filtration System

The water filter is located in the upper right-hand corner of the refrigerator compartment.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

IMPORTANT: The disposable water filter should be replaced at least every 6 months. If the water flow to the water dispenser or ice maker decreases noticeably before 6 months have passed, replace the water filter more often.

Water Filter Status Lights

The water filter status lights will help you know when to change the water filter. When the Order light is on, it is almost time to change the water filter. When the Replace light is on, a new water filter should be installed.

Reset Water Filter Status (on some models)

After replacing the water filter, press and hold Filter Reset for 3 seconds until the Order or Replace light turns off. See "Using the Controls" in the Quick Start Guide.

Replacing the Water Filter

To purchase replacement water filter, model EDR4RXD1/ EDR4RXD1B, UKF8001AXX-750 or UKF8001AXX-200, contact your dealer or call 1-800-253-1301 U.S.A. or 1-800-807-6777 Canada.

IMPORTANT: Air trapped in the water system may cause water and filter to eject. Always dispense water for at least 2 minutes before removing the filter or blue bypass cap.

1. Turn filter counterclockwise to remove. NOTE: There may be some water in the filter. Some spilling

may occur. Use a tower to wipe up any spills.

2. Remove sealing label from replacement filter and insert the filter end into the filter head.

3. Turn the filter clockwise until it stops. Snap the filter cover closed.

4. Flush the water system. See “Water Dispenser.” NOTE: The dispenser feature may be used without a water

filter installed. Your water will not be filtered. If this option is chosen, replace the filter with the blue bypass cap.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Turn off the Temperature control(s). See “Using the Controls”

in the Quick Start Guide.

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them

together so they don’t shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so it

rolls more easily or raise the leveling screws so they don’t scrape the floor. See online “Adjust the Door(s)” or “Door Closing and Door Alignment.”

9. Tape the doors closed and tape the power cord to the back of

the refrigerator.

When you get to your new home, put everything back and refer to “Installation Instructions” for preparation instructions. If your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

Vacation and Moving Care

Vacations

If You Choose to Leave the Refrigerator On While You’re Away:

1. Use up any perishables and freezer other items.

2. If your refrigerator has an automatic ice maker, and is

connected to the household water supply, turn off the water supply to the refrigerator. Property damage can occur if the water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker. NOTE: Raise the wire shutoff arm to Off (arm up) position.

4. Empty the ice bin.

If You Choose to Turn Off the Refrigerator Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

� Turn off the water supply to the ice maker at least one day

ahead of time.

� When the last load of ice drops, raise the wire shutoff arm

to the Off (up) position.

3. Empty the ice bin.

4. Turn off the Temperature control(s). See “Using the Controls”

in the Quick Start Guide.

5. Clean refrigerator, wipe it, and dry well.

6. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and mold from building up.

Moving

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker: � Turn off the water supply to the ice maker at least one day

ahead of time.

� Disconnect the water line from the back of the refrigerator. � When the last load of ice drops, raise the wire shutoff arm

to the Off (up) position.

WARNING

Excessive Weight Hazard

Use two or more people to move and install or uninstall appliance.

Failure to do so can result in back or other injury.

Remove the Packaging

� Remove tape and glue residue from surfaces before turning on

the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

� Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see “Refrigerator Safety.”

� Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in the “Maintenance and Care” section of your Owner’s Manual.

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Electrical Requirements

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.

Recommended Grounding Method

A 115 V, 60 Hz, AC-only 15 A or 20 A fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator and approved accessories be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the refrigerator to OFF. Depending on your model, turn the refrigerator control to the word OFF, or press the refrigerator down arrow touch pad until a dash (–) appears in refrigerator displays as shown. Disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the temperature controls to the desired setting. See “Quick Start Guide.”

� Staff kitchen areas in shops, offices and other working

environments.

� Farm houses and by clients in hotels, motels and other

residential type environments.

� Bed and breakfast type environments. � Catering and similar non-retail applications.

To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) of space on each side and at the top. Allow for 1" (2.54 cm) of space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a fixed wall, leave 2 1/2" (6.3 cm) minimum on the hinge side (some models require more) to allow for the door to swing open.

NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

Water Supply Requirements

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from appliance.

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor, household

use only. This appliance is intended to be used in a household and similar

applications such as:

Tools Needed:

� Flat-blade screwdriver � 7/16" and 1/2" Open-end or two

adjustable wrenches

IMPORTANT:

� Connect to a potable water supply only.

� All installations must meet local plumbing code requirements. � Do not use a piercing-type or 3/16 " (4.76 mm) saddle valve

which reduces water flow and clogs more easily.

� Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain above freezing.

� For models with water filters, the disposable water filter should

be replaced at least every 6 months.

� 1/4" Nut driver � 1/4" Drill bit � Cordless drill

Water Pressure

A cold water supply with water pressure of between 35 and 120 psi (241 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

IMPORTANT: Flush the water system before calibrating Measured Fill. See “Flush the Water System” in the Owner’s Manual.

If you have questions about your water pressure, call a licensed, qualified plumber.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

� Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and ordinances.

� The water tubing on the back of the refrigerator (which is used

to connect to the household water line) is a PEX (cross-linked polyethylene) tube. Copper and PEX tubing connections from the household water line to the refrigerator are acceptable, and will help avoid off-taste or odor in your ice or water. Check for leaks. If PEX tubing is used instead of copper, we recommend contacting Service to obtain current part numbers.

� Install tubing only in areas where temperatures will remain

above freezing.

� If you turn on the refrigerator before the water line is

connected, turn off the ice maker to avoid excessive noise or damage to the water valve.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

3. Find a 1/2" to 1 1/4" (12.7 mm to 31.8 mm) vertical cold water

pipe near the refrigerator.

� Make sure it is a cold water pipe. � Horizontal pipe will work, but the following procedure must

be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower right rear of the refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper or PEX tubing. Be sure both ends of copper or PEX tubing are cut square.

5. Using a cordless drill, drill a 1/4" (6.35 mm) hole in the cold

water pipe you have selected.

A. Cold water pipe B. Pipe clamp C. Copper or PEX tubing D. Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten or you may crush the copper tubing.

8. Place the free end of the tubing in a container or sink, and turn

on the main water supply. Flush the tubing until water is clear. Turn off the shutoff valve on the water pipe.

E. Compression sleeve F. Shutoff valve G. Packing nut

Connect to Refrigerator

Depending on your model, the water line may come down from the top or up from the bottom. Follow the connection instructions for your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the

copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Confirm copper tubing is secure by pulling on copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the tubing. Secure copper or PEX tubing to refrigerator cabinet with a “P” clamp.

A. Copper or PEX

tubing

B. “P” clamp

Compression nut

D. Compression sleeve

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Style 2

1. Create a service loop (minimum diameter of 2 ft. [61 cm]) with

the copper or PEX tubing. Avoid kinks when coiling the tubing.

2. Remove the plastic cap from water valve inlet port. Place a

compression nut and sleeve on the copper or PEX tubing.

3. Insert the end of the copper or PEX tubing into the water valve

inlet port. Shape tubing slightly so that the tubing feeds straight into the port to avoid kinks.

4. Slide the compression nut over the sleeve and screw into the

water valve inlet port.

A. PEX water tubing B. Sleeve

5. Using an adjustable wrench, hold the nut on the plastic water

line to keep it from moving. Then, with a second wrench turn the compression nut on the copper tubing counterclockwise to completely tighten. Do not overtighten.

A. “P” clamp B. PEX water line

6. Check connection by pulling on tubing. Attach the PEX water

line to the refrigerator cabinet with a “P” clamp.

7. Turn on water supply to the refrigerator and check for leaks.

Correct any leaks.

C. Compression nut D. Copper or PEX tubing

C. Compression nut D. Copper tubing

REFRIGERATOR FEATURES

Crisper Humidity Control

You can control the amount of humidity in the moisture-sealed crisper. Depending on your model, adjust the control to any setting between Fruit and Vegetables or Low and High.

� Fruit/Low (open) for best storage of fruits and vegetables with

skins.

� Vegetables/High (closed) for best storage of fresh, leafy

vegetables.

For information on additional features for your appliance, see online "Feature Guide."

DOOR AND HANDLE INSTRUCTIONS

Refrigerator Doors and Drawer

TOOLS NEEDED: 5/16", 3/8", 1/4" hex head socket wrench, a

Torx† T20 screwdriver, a #2 Phillips screwdriver, and a flat-blade screwdriver

IMPORTANT:

� Your refrigerator may have a standard reversible refrigerator

door with either a freezer door or freezer drawer, or French doors. Follow the instructions specific to the door style of your model.

� If you only want to remove and replace the doors, see

“Remove Doors and Hinges” and “Replace Doors and Hinges.”

� Before you begin, turn the refrigerator control Off, and remove

food and adjustable door or utility bins from the doors.

Remove and Replace Door Handles

REFRIGERATOR DOOR HANDLES Refrigerator Door Handle Style 1

Complete the Installation

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3–prong outlet. NOTE: Allow 24 hours to produce the first batch of ice.

Discard the first three batches of ice produced. Allow 3 days to completely fill the ice storage bin.

2. Flush the water system. See “Water and Ice Dispensers.”

A. 3/32” Setscrew

� Using a 3⁄32" or 1⁄8" hex key, loosen the two setscrews located

on the side of each handle. Pull the handle straight out from the drawer. Make sure you keep the screws for reattaching the handles.

� To replace the handles, reverse the directions.

Refrigerator Door Handle Style 2

A. Handle Trim C. Refrigerator Door Handle B. Flat–Head Handle Screws

� Remove the screw cover. � Remove the handle assembly. Keep all parts together. � To replace the handles, reverse the directions.

Refrigerator Door Handle Style 3

� To remove the handle, remove the screw attaching the trim to

the upper end of the handle. Using a flat-blade screwdriver wrapped in masking tape, pry the trim piece from the lower end of the handle. Then, remove the screws attaching the handle to the door.

� To replace handle, reverse directions.

Refrigerator Door Handle Style 5

� To remove the handle, grasp the lower part of the handle

firmly, slide the handle up and pull the handle straight out from the door.

� To replace the handle, position the handle so that the large

holes in the mounting clips are down and align the holes with the door studs. Rotate the handle so that the mounting clips are flat against the door and slide the handle down to engage.

FREEZER DOOR HANDLES Freezer Door Handle Style 1

A. Flat–Head Handle Screws B. Refrigerator Door Handle

� Using a 3⁄32" or 1⁄8" hex key, loosen the two setscrews located

on the side of each handle. Pull the handle straight out from the drawer. Make sure you keep the screws for reattaching the handles.

� To replace the handles, reverse the directions.

Refrigerator Door Handle Style 4

A. Trim Screw C. Top Trim B. Handle Screws D. Bottom Trim

A. 3/32” Setscrew

� Using a 3⁄32" or 1⁄8" hex key, loosen the two setscrews located

on the side of each handle. Pull the handle straight out from the drawer. Make sure you keep the screws for reattaching the handles.

� To replace the handles, reverse the directions.

Freezer Door Handle Style 2

A. Handle Trim C. Freezer Drawer Handle B. Flat–Head Handle Screws

� Remove the screw cover. � Remove the handle assembly. Keep all parts together. � To replace the handles, reverse the directions.

Freezer Door Handle Style 3

A. Flat–Head Handle Screws

� Remove screws and handle. � To replace handle, reverse directions.

Freezer Door Handle Style 4

A. Flat–Head Screws B. Freezer Drawer Handle

� Remove screws and handle. � To replace the handles, reverse the directions.

Freezer Door Handle Style 5

3. Remove the parts for the top hinge as shown below. Lift the

refrigerator door free from the cabinet.

A. Hinge Cover Screw C. 5/16” Hex-Head Hinge Screws B. Top Hinge Cover D. Top Hinge

4. Remove the parts for the bottom hinge as shown below.

� To remove the handle, grasp the lower part of the handle

firmly, slide the handle up and pull the handle straight out from the door.

� To replace the handle, position the handle so that the large

holes in the mounting clips are down and align the holes with the door studs. Rotate the handle so that the mounting clips are flat against the door and slide the handle down to engage.

Remove Doors and Hinges

STANDARD DOOR

Hex Head Top Hinge Screw

Standard Door - Freezer drawer models

1. Unplug refrigerator or disconnect power

2. Keep the refrigerator door closed until you are ready to lift it

free from the cabinet. NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

A. Hinge Pin Cover C. Hinge Screws B. Bottom Hinge

Freezer door models

1. Unplug refrigerator or disconnect power.

2. Keep the freezer door closed until you are ready to lift it free

from the cabinet. NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

3. Remove the parts for the top hinge as shown below. Lift the

refrigerator door free from the cabinet.

A. Hinge Cover Screw C. 5/16” Hex-Head Hinge Screws B. Top Hinge Cover D. Top Hinge

4. Remove the center hinge pin and remove the hinge screws as shown below. Lift the freezer door free from the cabinet.

A. Hinge Pin Cover C. Hinge Screws B. Center Hinge

5. Remove the base grille by grasping the grille firmly with both hands and pulling it toward you.

6. Remove the parts for the bottom hinge as shown below.

3. Starting with the right-hand side door, remove the parts for the

top hinge as shown below. Lift the refrigerator door from the bottom hinge pin.

A. Hinge Cover Screw C. 5/16” Hex-Head Hinge Screws B. Top Hinge Cover D. Top Hinge

4. Remove the hinge pin cover from the bottom hinge pin and

keep it for later use.

5. Before removing the left-hand side door, disconnect the wiring

plug located on top of the top hinge by wedging a flatblade screwdriver or your fingernail between the two sections..

A. Hinge Pin Shim D. Roller Bracket B. Bottom Hinge E. 3/8” Hex-Head Screws C. Hinge Plate

WARNING

Electrical Shock Hazard Disconnect power before removing doors. Failure to do so could result in death or electrical shock.

FRENCH DOORS

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet. NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working

NOTE: The green, ground wire remains attached to the hinge.

6. Remove the parts for the left-hand side door top hinge as

shown in the Top Hinge graphic in Step 3. Lift the door from the bottom hinge pin.

NOTE: Remove the hinge pin cover from the bottom hinge pin and keep it for later use.

A. Hinge Pin Cover C. Hinge Screws B. Bottom Hinge

+ 23 hidden pages