KitchenAid KPEU722MSS, KPEC992MSS Owner’s Manual

Whirlpool - CIC 8/Ib/Oq Z:zo PM _A55 I/ZI _zgnnrax

IMPORTAN
Read and save

these instructions.

IMPORTANT:

Installer: 8afore installingthe hood liner,read

the InstallationInstrumionsforthe exterior

blowerusedwith hoodliner,

Leave Installation Instructions with the
homeowner,

Homeowner: KeepInstallation Instructions

for future reference.

Save Installation Instructions for local
electrical inspector's use.

Part No. 436001862/8285495

Quick Reference

Table of Contents:

Pages

[] Beforeyou start
[] Electricalrequirements

[] Cabinetdimensions
[] Product dimensions

I_ - 151 Installationsteps

[]- [] UseandCareInformation

[] Wiringdiagram
[] Warranty

[_ -I10_ RequestingAssistsnceor

Service

Whirlpool - ClC 8/16/04 2:25 PM PAGE 1/21 RightFax

WARNING --TO REDUCE THE

RISK OF FIRE, ELECTRIC

SHOCK. OR INJURY TO

Your safety and the safety of

nthem is very important.

We haveprovidedmanyimportant

safetymessagesinthismanualand
onyourappliance.Alwaysreadand

obeyallsafetymessaoes.

Thisisthesafetyalertsymbol
Thissymbolalertsyouto
potentialhazardsthatcankill

or hurtyouandothers.Allsafety
messaoeswillfollow thesafetyalert

symbolandeithertheword"DANGER"
or'WARNING".Thesewordsmean:

Youcanbe killedor seriouslyInjured

ityoudon't_ lollow
Instm_ione.

Youcanbe killedor seriouslyinjured

ifyoudon'tfollowinstructions.

Allsafetymessageswilltell youwhat
thepotentialhazardis,LelJyouhowto

reducethechanceof injury,andtell

youwhatcanhappenifthe

instructionsarenotfollowed.

IMPORTANT: Observe all
governing codes and ordinances.
Proper installation is your

responsibility. Make sure you have
everything necessaryfor correct

installation. It is the responsibility of

the installer to comply with the

clearances specified.
Checkthe location where the hood

liner will be installed.The location

should be away from strong draft
areas, such as windows, doors, and

strong heating vents.
Mobilehomeinstallation

The installation of this hood liner

must conform to the Manufactured
Home Construction Safety

Standards,Title 24 CFR, Part 328

(formerly the Federal Standard for
Mobile Home Construction and

Safety,Title 24, HUD, Part 280) or
when such standard is not

applicable, the Standard for

Manufactured Home Installation
1982 (Manufactured Home Sites,

Communities and Setups) ANSI
A225.1/NFPA 501A*, or latest edition,
or with local codes.

PERSONS, OBSERVE THE
FOLLOWING:

Installationwork and electrical

wiring must be done by qualified

]ersan(s) in accordance with all

applicable Codesand Standards,
including Fire Rated

Construction. Sufficient air is

needed for proper combustion

and exhausting of gasesthrough
the flue (chimney) offuel burning

equipment to prevent back
drafting. Follow the heating

equipment manufacturer's

guideline and safety standards
such as those published by the

National Fire Protection

Association (NFPA),and the
American Society of Heating

Refrigeration and Air
Conditioning Engineers

(ASHRAE),and the localcode
authorities.

When cuttingor drillingintowall or
ceiling,do not damage electrical

wiringand other hiddenutilities.
Ducted fans mustalways be

ventedto the outdoors.
WARNING -- To reducethe risk

offire, use onlymetal ductwork.
This unitmust be grounded.

Thishoodliner mustbe usedwith

ExteriorBlowerModels:

KPEC992M rated for 900 cfm

(25.5 cm/m) or.

KPEU722M rated for 1200 cfm

(34.0 cm/m).

Both models are available from

your dealer.
This fan suitabable for usewith

solid-state speed controls.

Tools and

materials needed

for installation:

• compassor11"(27.9cm) circletemplate

• fiat bladescrewdriver

• Phillipsscrewdriver

• plTers

• metalsnips

• drill

• 1-1/4"13.0cm)die. drill bit

• 5/16' (7.9cm)dis.drill bit

• pencil

• ruler

• sabersawor keyholesaw

• ducttape

• 3/4"(10.0rnm}U.L- or C.SA.-Listed

strainrelief

IMPORTANT:Observe all

governing codes and ordinances.
The Exterior Blower is connected
to the fused electrical system at

the wiring box of the Hood Liner.

refer to the Installation
Instructions supplied with the

Exterior Blower model for the

electrical system.

It is the customer's responsibility:

•To contact a qualified electrical

installer.

•To assure that the electrical

installation is adequate and in
conformance with National

Electrical Code, ANSI/NFPA 70

-- latest edition*, or CSA

Standards C22.1-94, Canadian
Electrical Code, Part 1 and
C22.2 No.0-M91 - latest

edition** and all local codes
and ordinances.

A 120-volt, 60 hz,AC-only, fused

electrical system ia required. A
separate 15-amp circuit is

recommended.

A separate ground wire must be

used. It is recommended that a
qualified electrician determine

that the ground path isadequate..

Do not ground to a gas pipe.

Check with a qualified electrician if
you are not sure range hood is

properly grounded.
Do not have a fuse in the neutral

or ground circuit.
The connection at the hood liner
wiring box must be with copper

wire only.

IMPORTANT:

Save installation Instructions for
electrical inspector's use.

The 120-volt supply to the hood

liner wiring box should be

connected directly to the fused
disconnect (or circuit breaker) box

through flexible armored or

nonmetallic sheathed copper cable,

A U,L.- or C.S.A,-listad strain relief
must be provided at each end of the

power supply cable, Wire sizes

(COPPERWIRE ONLY) and

connections must conform with the
rating of the appliance as specified

on the model/serial rating plate.
Wire sizes must conform to the

requirements of the National

Whirlpool - ClC 8/18/04 2:25 PM PAGE 1/21 RightFax

ElectricalCodeANSI/NFPA70 --
latestedition*, or CSAStandards

C22.1-94,Canadian ElectricalCoda
Part 1 and C22.2 No. 0-M91 - latest

edition** and all local codas and
ordinances.

i

hoodl]nerls
22"(55.9cm)
deep

A UI.- orC.S.A.-listsd strainrelief
mustbe providedatthe power

supplycableelectricalknockoutof
the HoodLiner,

rain. cabinet openlng wldths:
36" (914 cm) model, 36" (91.4 cm)
48" (121,9 cm) model, 48" (121.9 cm)

30"(76,2 cm) mln,
he] ht above

caogklng surface

Copies o¢the Ka ndalds lilr_d may be
obmined from:

* NaUonal am PmtectionAr_odation

One Bst_erymamh Park
QUnq/, Massachusetts 02268

w* CSA Intern_onst

8501 East PleasantYalley Road
Cleveland, Ohio _,4131-5675

determine hood suppoe depth so

that front enclosure Isflush with

adJolning enclosure.

.,,,,,,,,x_.,,,,,,,,,,_ front

_ JW_;f_jili_E!_iiiiiii__iiii_iiii_ enclosure

........_====="==_ _ [II

hood liner

hood support
must be capable

of supportln
50 Ibs. (22,7gkg)

/ _JN

electrical

knockouts

36" (91.4 cm) model:

35-13/16" (91`0 cm)

48" (121`9 cm) model:

47-13/16" (121.4 cm)

5-1B/16=

(15.1 cm)

2-3/4" 17-5/16"

(7.0cm) (40.0 cm) center line

(5.1 cm)

of hood

- ._, .

5-15/16"

(19,1cm)

36" (91,4 cm,) model:"'--...

15-23/32 (39.9 cm) "'_,_.

_,8"(121,9 cm) model: /

21-23/32" (552

36=(91,4 cm) model:

31-7/1a" (79,9 cm)

48" (121,9 cm) model:

43-7/16" (110.3cm)