KitchenAid KGRA806PBL02, KGSA906PBL02, KGSI901PBL01, GW395LEPT03, GW395LEPT04 Installation Guide

...

INSTALLATIONINSTRUCTIONS

30"(76.2 CM) FREESTANDINGAND SLIDE-INGAS RANGES

INSTRUCTIONSPOURL'INSTALLATIONDESCUISINIERES

AUTOPORTANTESETENCASTRABLESDE30"(76,2 CM)

Table of Contents/Table des matieres .................................................................................. 2

iMPORTANT:

Save for local electrical inspector's use. Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

iMPORTANT :

,&,conserver pour consultation par I'inspecteur local des installations electriques.

Installateur : Remettre les instructions d'installation au proprietaire. Propri_taire : Conserver les instructions d'installation pour reference ulterieure.

9761413

TABLEOF CONTENTS TABLEDESMATIERES

RANGE SAFETY ............................................................................. 2

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 6

Gas Supply Requirements ........................................................... 6

Countertop Preparation ............................................................... 7

INSTALLATION INSTRUCTIONS .................................................. 8

Unpack Range .............................................................................. 8

Install Anti-Tip Bracket ................................................................. 8

Install Rear Vent ........................................................................... 9

Verify Anti-Tip Bracket Location .................................................. 9

Level Range .................................................................................. 9

Make Gas Connection ................................................................. 9

Electronic Ignition System ......................................................... 10

Replace Oven Racks & Storage or Warming Drawer ................ 12

Complete Installation ................................................................. 12

GAS CONVERSIONS .................................................................... 13

LP Gas Conversion .................................................................... 13

Natural Gas Conversion ............................................................. 15

ANTI-TIP BRACKET TEMPLATE ................................................ 35

RANGESAFETY

SECURITI_ DE LA CUlSINI_RE .................................................... 19

EXIGENCES D'INSTALLATION ................................................... 20

Outillage et pieces ...................................................................... 20

Exigences d'emplacement ......................................................... 20

Specifications electriques .......................................................... 22

Specifications de I'alimentation en gaz ..................................... 23

Preparation du plan de travail .................................................... 24

INSTRUCTIONS D'INSTALLATION ............................................. 24

Deballage de la cuisiniere .......................................................... 24

Installation de la bride antibasculement .................................... 25

Installation du raccord du conduit d'evacuation a I'arriere .......26

Verification de I'emplacement de la bride antibasculement ......26

Mise a niveau de la cuisiniere .................................................... 26

Raccordement a la canalisation de gaz ..................................... 26

Systeme d'allumage electronique .............................................. 27

Reinstallation des grilles dans le four et du

tiroir de remisage ou du tiroir-rechaud ...................................... 29

Achever I'installation .................................................................. 29

CONVERSIONS POUR CHANGEMENT DE GAZ ....................... 30

Conversion pour I'alimentation au propane ............................... 30

Conversion pour I'alimentation au gaz naturel .......................... 32

GABARIT POUR LA BRIDE ANTIBASCULEMENT .................... 35

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

i WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

In the State of Massachusetts, the following installation instructions apply: [] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts. [] If using a ball valve, it shall be a T-handle type. [] A flexible gas connector, when used, must not exceed 3 feet.

A child or adult can tip the range and be killed. Connect anti-tip bracket to rear range foot.

l___ 1 Tip Over Hazard

Reconnect the anti=tip bracket, if the range is moved. Failure to follow these instructions can result in death or serious burns to children and adults.

INSTALLATIONREQUIREMENTS

s end Pcstts

Gather the required tools and parts before starting installation. Read and follow the safety instructions provided with any tools

listed here.

Tools needed

• Tape measure • Marker or pencil

• Flat-blade screwdriver • Masking tape

• Phillips screwdriver • Pipe-joint compound

• Level

• Hand or electric drill • s/16"(4.8 mm) carbide-tipped

• Hammer concrete/ceramic floors)

• Channel lock pliers • Noncorrosive leak-detection

• Pipe wrench

• 15/16"combination wrench

• %" drive ratchet • 1/2"combination wrench

• %" nut driver • 7 mm combination wrench

• 1/8"(3.2 mm) drill bit (for • 7 mm nut driver wood floors)

Parts supplied

Check that all parts are included.

resistant to LP gas

masonry drill bit (for

solution

For LP/Natural Gas

Conversions

• SizeT20 TORX _tscrewdriver

4o /

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the oven frame behind the storage drawer panel.

• The range should be located for convenient use in the kitchen.

• Recessed installations must provide complete enclosure of the sides and rear of the range.

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond

the bottom of the cabinets.

• All openings in the wall or floor where range is to be installed must be sealed.

• Do not seal the range to the side cabinets.

• Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

• The floor anti-tip bracket must be installed. To install the anti- tip bracket shipped with the range, see "Install Anti-Tip

Bracket" section.

• Grounded electrical supply is required. See "Electrical Requirements" section. Proper gas supply connection must be available. See "Gas Supply Requirements" section.

• Contact a qualified floor covering installer to check that the floor covering can withstand at least 200°F (93°C).

• Use an insulated pad or r/4" (0.64 cm) plywood under range if installing range over carpeting.

IMPORTANT: Some cabinet and building materials are not designed to withstand the heat produced by the oven for baking and self-cleaning. Check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.

A. Anti-tip bracket B. Plastic anchors (2) C. #10 x _A" screws (2) D. Rear vent (for slide-in models)

Brackets must be securely mounted to subfloor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local

hardware store.

Parts needed

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See "Electrical Requirements" and "Gas Supply Requirements" sections.

1-®TORX is a registered trademark of Textron Innovations Inc.

Mobile Home - Additional Installation Requirements The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home

Installations, ANSI A225.1/NFPA 501A or with local codes. In Canada, the installation of this range must conform with the

current standards CAN/CSA-A240-1atest edition, or with local codes.

Mobile home installations require:

• When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards

listed above.

Product Dimensions

Freestanding Range

*When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm) countertop; front of oven door protrudes 1%" (4.8 cm) beyond 24" (61 cm) base cabinet.

Installation Clearances

Cabinet opening dimensions shown are for 25" (64 cm) countertop depth, 24" (61 cm) base cabinet depth and

36" (91.4 cm) countertop height.

Freestanding and Slide-in Ranges

A. 77/8" (20 cm) B. 30" (76.2 cm) C. 43%" (111.4 cm) overall

height

Slide-in Range

D. 36" (91.4 cm) cooktop

height with levering legs lowered 1V2turns

E. 30" (76.2 cm)

E *27" (68.6 cm) max. to

handle

A. 18" (45.7 cm) upper cabinet to countertop B. 13" (33 cm) max. upper cabinet depth

C. 30" (76.2 cm) min. opening width D. For minimum clearance to top of the cooktop, see NOTE.

E.30" (76.2 cm) min. opening width F. This shaded area recommended for installation of rigid gas pipe

G. 8" (20.3 cm) H. Grounded outlet

I. 17" (43.2 cm)

J. 2" (5.1cm)

K. 4V2" (1 !.4 cm)

L. 2" (5.1 cm) min. clearance from both sides of the range to the

side wall or other combustible material 5" (12.7 cm) for the ranges with reversible grate insert (wok ring)

A. 35%" (90.5 cm) cooktop

height with leveling legs

lowered 1V2turns

B. 30Wl_" (77.9 cm)

*NOTE: 24" (61 cm) minimum when bottom of wood or metal

cabinet is protected by not less than 1/4"(0.64 cm) flame

retardant millboard covered with not less than No. 28 MSG

sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the

cooking platform and the bottom of an unprotected wood or

metal cabinet.

C. 25" (63.5 cm) D 23W' (59.8 cm) E. *27" (68.6 cm) to handle

F. 30" (76.2 cm)

Ebctdc(s , equ is

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

IMPORTANT: The range must be electrically grounded in accordance with local codes and ordinances, or in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1

This range is equipped with an electronic ignition system that will

not operate if plugged into an outlet that is not properly polarized. If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path is adequate. A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this range be provided.

• Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are necessary. Check that the outlet provides 120-volt power and is correctly grounded.

• The wiring diagram is located on the underside of the storage drawer or below the warming drawer in a clear plastic bag.

NOTE: The metal chassis of the range must be grounded in order for the control panel to work. If the metal chassis of the range is not grounded, no keypads will operate. Check with a qualified electrician if you are in doubt as to whether the metal chassis of the range is grounded.

Explosion Hazard

Use a new CSA international approved gas supply line.

install a shut-off valve. Securely tighten all gas connections.

if connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include: licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances. IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest

edition.

Type of Gas

Natural Gas:

This range is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas.

• This range is factory set for use with Natural gas. See "Gas Conversions" section. The model/serial rating plate located on the frame behind the storage drawer has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.

LP Gas conversion: Conversion must be done by a qualified service technician.

No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. See "Gas

Conversions" section.

Gas Supply Line

Provide a gas supply line of 3A" (1.9 cm) rigid pipe to the range location. A smaller size pipe on longer runs may result

in insufficient gas supply. Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON °t tape. With LP gas, piping or tubing size can be 1/2"(1.3 cm) minimum. Usually, LP gas suppliers determine the size and materials used in the system.

Flexible metal appliance connector:

If local codes permit, a new CSA design-certified,

4 - 5 ft (122 - 152.4 cm) long, 1/2"(1.3 cm) or 3A"(1.9 cm) I.D., flexible metal appliance connector may

be used for connecting range to the gas supply line.

• A r/2" (1.3 cm) male pipe thread is needed for connection to the female pipe threads of the inlet to the appliance

pressure regulator.

• Do not kink or damage the flexible metal tubing when moving the range.

Rigid pipe connection:

The rigid pipe connection requires a combination of pipe fittings to obtain an in-line connection to the range. The rigid pipe must be level with the range connection. All strains must be removed from the supply and fuel lines so range will be

level and in line.

LP Gas:

Minimum pressure: 11" WCP Maximum pressure: 14" WCP Contact local gas supplier if you are not sure about the inlet

pressure.

Burner Input Requirements

Input ratings shown on the model/serial rating plate are for elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a rate of 4% for each 1,000 ft (304.8 m) above sea level (not

applicable for Canada).

Gas Supply Pressure Testing

Line pressure testing above 1/2psi gauge (14" WCP)

The range and its individual manual shutoff valve must be disconnected from the gas supply piping system during any

pressure testing of that system at test pressures greater than r/2psi (3.5 kPa).

Line pressure testing at V2psi gauge (14" WCP) or lower

The range must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure

testing of that system at test pressures equal to or less than 1/2psi (3.5 kPa).

Must include a shutoff valve: The supply line must be equipped with a manual shutoff

valve. This valve should be located in the same room but external to the range. It should be in a location that allows

ease of opening and closing. Do not block access to shutoff valve. The valve is for turning on or shutting off gas to the range.

A.Gas supply line B.Shutoff valve "open" position C. Torange

Gas Pressure Regulator

The gas pressure regulator supplied with this range must be

used. The inlet pressure to the regulator should be as follows for proper operation:

Natural Gas:

Minimum pressure: 6" WCP Maximum pressure: 14" WCP

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

The cooktop sides of the slide-in range fit over the cutout edge of your countertop.

If you have a square finish (flat) countertop and the opening width is 30" (76.2 cm), no countertop preparation is required.

Formed front-edged countertops must have molded edge shaved flat %" (1.0 cm) from each front corner of opening.

Tile countertops may need trim cut back %" (1.0 cm) from each

front corner and/or rounded edge flattened.

If countertop opening width is greater than 30" (76.2 cm), adjust the %" (1.0 cm) dimension.

Countertop must be level. Place level on countertop, first side to side; then front to back. If countertop is not level, range will not be level. Oven must be level for satisfactory baking conditions.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install range. Failure to do so can result in back or other injury.

1. Remove shipping materials, tape and protective film from

range. Keep cardboard bottom under range. Remove oven racks and parts package from inside oven.

2. Take 4 cardboard corners from the carton. Stack one cardboard corner on top of another. Repeat with the other 2

corners. Place them lengthwise on the floor behind the range to support the range when it is laid on its back. Using 2 or

more people, firmly grasp the range and gently lay it on its back on the cardboard corners.

3. Pull cardboard bottom firmly to remove.

4. Use an adjustable wrench to loosen the leveling legs.

5. Place cardboard or hardboard in front of range. Using 2 or more people, stand range back up onto cardboard or

hardboard.

If countertop is not flush with cabinet opening edge, align template with overhang.

If cabinet opening is wider than specified in the "Location Requirements" section, adjust template so range will be centered in cabinet opening.

To mount anti-tip bracket to wood floor, drill two 1/s"(3.2 mm) holes at the positions marked on the bracket template. Remove template from floor.

Tip Over Hazard

A child or adult can tip the range and be killed. Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved. Failure to follow these instructions can result in death

or serious burns to children and adults.

Contact a qualified floor covering installer for the best procedure

for drilling mounting holes through your type of floor covering.

Before moving range, slide range onto shipping base, cardboard or hardboard.

f. Remove template from the anti-tip bracket kit (found inside

the oven cavity) or from the back of this manual.

2. Place template on the floor in cabinet opening so that the left edge is against cabinet and top edge isagainst rear wall, molding or cabinet.

3. Tape template into place.

To mount anti-tip bracket to concrete or ceramic floor, use a 3A6"(4.8 mm) masonry drill bit to drill 2 holes at the positions

marked on the bracket template. Remove template from floor.

6. Tap plastic anchors into holes with a hammer.

7. Align anti-tip bracket holes with holes in floor. Fasten anti-tip bracket with screws provided.

Depending on the thickness of your flooring, longer screws may be necessary to anchor the bracket to the subfloor.

Longer screws are available from your local hardware store.

8. Move range close to opening. Remove shipping base, cardboard or hardboard from under range.

9. Connect power supply cord as described in the "Electrical Connection" section.

fO. Move range into final position making sure rear leveling leg

slides into anti-tip bracket.

f 1. Continue installing your range using the following the

installation instructions.

Ifyouhaveaslide-inrange,therearventmustbeinstalled. Removetheoutsidescrewsfromthereartrimonrange.Use

screwstoattachrearventtorange.

Vis fpl/A $ p b:x,,,,@

Place rack in oven. Place level on rack, first side to side; then front to back.

If range is not level, pull range forward until rear leveling leg is removed from the anti-tip bracket. Use %" drive ratchet and channel lock pliers to adjust leveling legs up or down until range is level. Push range back into position. Check that rear leveling leg is engaged in anti-tip bracket.

NOTE: Oven must be level for satisfactory baking performance.

Excessive Weight Hazard

Use two or more people to move and install range. Failure to do so can result in back or other injury.

1. Move range close to cabinet opening.

2. Remove cardboard or hardboard from under range. Gently move range into its final position.

3. Pull drawer open to first stop position. Lift front of drawer to clear white wheels in drawer guides. Remove drawer and set it aside on a protected surface. See the Use and Care Guide

for the model drawer removal.

Making sure the anti-tip bracket is installed:

• Look for the anti-tip bracket securely attached to floor.

• Slide range back so rear range foot is under anti-tip

bracket.

Typical rigid pipe connection

A combination of pipe fittings must be used to connect the range to the existing gas line. Your connections may be different, according to the supply line type, size and location.

1. Apply pipe-joint compound made for use with LP gas to all pipe thread connections.

2. Using a pipe wrench to tighten, connect the gas supply to the range.

/ {_ .......D

A F

H /

A. Gas pressure regulator B. 90 ° elbow (must have

_/2"male pipe thread)

C. Nipple D. Union

E. Black iron pipe

F. Manual gas shutoff valve G. _2" or s/4"gas pipe H. Nipple

I. Union

J. 90 ° elbow

If installing the range in a mobile home, you must secure the range to the floor. Any method of securing the range is adequate as long as it conforms to the standards in the "Location Requirements" section.

Typical flexible connection

1. Apply pipe-joint compound made for use with LP gas to the

smaller thread ends of the flexible connector adapters (see B and G in following illustration),

2. Attach one adapter to the gas pressure regulator and the other adapter to the gas shutoff valve, Tighten both adapters.

3. Use a 1%6"combination wrench and channel lock pliers to attach the flexible connector to the adapters. Check that

connector is not kinked,

Remove cooktop burner caps and grates from parts package. Align notches in burner caps with pins in burner base. Burner caps should be level when properly positioned, If burner caps are not properly positioned, surface burners will not light. Place burner grates over burners and caps.

B C

H G F

A. Gas pressure regulator

B. Use pipe-joint compound

C. Adapter (must have _/2"male

pipe thread)

D. Flexible connector

E. Manual gas shutoff valve

F. F2"or 3/4"gas pipe G. Use pipe-joint compound H. Adapter

Complete Connection

1. Check that the gas pressure regulator shutoff valve is in the

"on" position.

A. Gaspressure regulatorshutoff valve

2. Open the manual shutoff valve in the gas supply line. The valve is open when the handle is parallel to the gas pipe.

A. Burner base B. Burner cap

C. Burner grate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord, Failure to follow these instructions can result in death,

fire, or electrical shock.

5. Plug into a grounded 3 prong outlet.

A.Closed valve B.Open valve

Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a

leak, Correct any leak found.

Initial lighting and gas flame adjustments Cooktop and oven burners use electronic igniters in place of

standing pilots. When the cooktop control knob is turned to the "LITE" position, the system creates a spark to light the burner. This sparking continues, as long as the control knob isturned to

"LITE," When the oven control is turned to the desired setting, sparking

occurs and ignites the gas,

Check Operation of Cooktop Burners

Standard Surface Burners

Push in and turn each control knob to the "LITE" position.

The flame should light within 4 seconds. The first time a burner is

lighted it may take longer that 4 seconds to light because of air in

the gas line.

TripleTier TM Flame Burner

To start simmer burner:

Push in and turn control knob to "LITE."

The flame should light within 4 seconds. The first time a burner is

lighted it may take longer that 4 seconds to light because of air in

the gas line.

To start power burner:

Push in and turn control knob to "POWER BURNER HIGH."

The flame should light within 4 seconds. The first time a burner is

lighted it may take longer that 4 seconds to light because of air in

the gas line.

If burners do not light properly:

• Turn cooktop control knob to the "OFF" position.

• Check that the range is plugged in and the circuit breaker has not tripped or the household fuse blown.

• Check that the gas shutoff valves are set to the "open" position.

• Check that burner caps are properly positioned on burner bases.

Repeat start-up. If a burner does not light at this point, contact

your dealer or authorized service company for assistance.

Adjust Flame Height

Adjust the height of top burner flames. The cooktop "low" burner flame should be a steady blue flame approximately W' (0.64 cm)

high.

If the "low" flame needs to be adjusted:

1. Remove the control knob.

2. Hold the knob stem with a pair of pliers. Use a small flat- blade screwdriver to turn the screw located in the center of

the control knob stem until the flame is the proper size.

3. Replace the control knob.

4. Test the flame by turning the control from "LO" to "HI," checking the flame at each setting.

Check Operation of Oven Bake Burner

1. Remove the oven rack. Remove the bake burner cover and place it on a protected surface.

2. Push the BAKE pad. Default temperature appears in the temperature display.

3. Press the START pad. Depending on your model, "PrE" and preheat time will appear in the temperature display

OR "PREHEATING" and "LO" (or actual temperature) will appear

in the temperature display.

The oven bake burner should light within 8 seconds, under certain conditions it may take the burner up to 50 to 60 seconds to light.

Electronic igniters are used to light the bake and broil burners.

C II _/

A. Oven bake burner cover B. Flame spreader

C. Oven bake burner

A. Low flame

B. High flame

The flame can be adjusted using the adjustment screw in the

center of the valve stem. The valve stem is located directly underneath the control knob.

A.Adjustment screw

Adjust Oven Bake Burner Flame (if needed)

Remove access cover plate (1screw) located on the upper wall, inside the storage or warming drawer compartment.

Check the oven bake burner for proper flame. This flame should have a 1/2"(1.3 cm) long inner cone of

bluish-green, with an outer mantle of dark blue, and should be clean and soft in character. No yellow tips, blowing or

lifting of flame should occur. If the oven bake flame needs to be adjusted, locate the air

shutter near the center rear of the range. Loosen the locking screw and rotate the air shutter until the proper flame

appears. Tighten locking screw.

B .......

A. Air shutter B. Locking screw

+ 25 hidden pages