KitchenAid KGHS02RWH2, KGHS02RWH1, KGHS02RMT2, KGHS02RMT1 Owner’s Manual

Ki|chen_kid ®

FRONT-LOADING GAS DRYER

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

In Canada, call : 1-800-807-6777 or visit our website at...

www.kitchenaid.com or www.KitchenAid.ca

SECADORA A GAS DE CARGA FRONTAL

..........._'_.,.,{e:_ ;

Si tiene preguntas respecto alas caracterfsticas, funcionamiento/rendimiento, partes, accesorios o servicio t_cnico, Ilame al: 1-800-422-1230

Para la instalacion y el servicio Ilame al: 1-800-807-6777 o visite nuestro sitio web en... www, kitchenaid,com

SECHEUSE A GAZ A CHARGEMENT A L'AVANT

Au Canada, composez le 1-800-807-6777

ou visitez notre site web &... www.KitchenAid.ca

Table of Contents/Indice/Table des matieres .................................................................. 2

8578200

TABLEOF CONTENTS

DRYER SAFETY .............................................................................. 3

INSTALLATION INSTRUCTIONS .................................................. 4

Tools and Parts ............................................................................ 4

Options ......................................................................................... 5

Location Requirements ............................................................... 5

Electrical Requirements ............................................................... 7

Gas Supply Requirements ........................................................... 7

Venting Requirements .................................................................. 9

Plan Vent System ....................................................................... 10

Install Vent System ..................................................................... 11

Install Leveling Legs ................................................................... 11

Make Gas Connection ............................................................... 12

Connect Vent .............................................................................. 12

Level Dryer ................................................................................. 12

Reverse Door Swing .................................................................. 12

Complete Installation ................................................................. 14

DRYER USE .................................................................................. 15

Starting Your Dryer ..................................................................... 15

INDICE

SEGURIDAD DE LA SECADORA ................................................ 24

INSTRUCCIONES DE INSTALACION ......................................... 26

Herramientas y piezas ................................................................ 26

Opciones .................................................................................... 26

Requisitos de ubicaci6n ............................................................. 26

Requisitos electricos .................................................................. 29

Requisitos del suministro de gas ............................................... 29

Requisitos de ventilaci6n ........................................................... 31

Planificaci6n del sistema de ventilaci6n .................................... 32

Instalacidn del sistema de ventilaci6n ....................................... 33

Instalaci6n de las patas niveladoras .......................................... 33

Conexi6n del suministro de gas ................................................ 34

Conexi6n del ducto de escape .................................................. 34

Nivelaci6n de la secadora .......................................................... 35

C6mo invertir el cierre de la puerta ............................................ 35

Complete la instalaci6n .............................................................. 36

USO DE LA SECADORA .............................................................. 37

Puesta en marcha de la secadora ............................................. 37

Stopping Your Dryer ................................................................... 16

Pausing or Restarting ................................................................. 16

Control Locked ........................................................................... 16

Drying and Cycle Tips ................................................................ 16

Status Lights ............................................................................... 17

Cycles ......................................................................................... 17

Additional Features .................................................................... 18

Drying Rack ................................................................................ 19

DRYER CARE ............................................................................... 19

Cleaning the Dryer Location ....................................................... 19

Cleaning the Lint Screen ............................................................ 19

Cleaning the Dryer Interior ......................................................... 20

Removing Accumulated Lint ...................................................... 20

Vacation and Moving Care ......................................................... 20

Changing the Drum Light ........................................................... 20

TROUBLESHOOTING .................................................................. 21

ASSISTANCE OR SERVICE ......................................................... 22

WARRANTY .................................................................................. 23

Detencidn de la marcha de la secadora .................................... 38

Pausa o reanudaci6n de la marcha ........................................... 38

Control bloqueado ..................................................................... 38

Sugerencias de ciclos y secado ................................................ 38

Luces de estado ......................................................................... 39

Ciclos .......................................................................................... 39

Caracter[sticas adicionales ........................................................ 40

Estante de secado ...................................................................... 41

CUIDADO DE LA SECADORA .................................................... 42

Limpieza del lugar donde esta la secadora ............................... 42

Limpieza del filtro de pelusa ...................................................... 42

Limpieza del interior de la secadora .......................................... 43

Eliminaci6n de pelusa acumulada ............................................. 43

Cuidado para las vacaciones y la mudanza .............................. 43

Cambio de la luz del tambor ...................................................... 43

SOLUCION DE PROBLEMAS ...................................................... 43

AYUDA O SERVICIO TC:CNICO ................................................... 45

GARANTIA ..................................................................................... 46

TABLE DES MATIERES

S¢:CURITI:!:DE LA S¢:CHEUSE .................................................... 47

INSTRUCTIONS D'INSTALLATION ............................................ 49

Outillage et pieces ...................................................................... 49

Options ....................................................................................... 49

Exigences d'emplacement ......................................................... 49

Specifications electriques .......................................................... 52

Specifications de I'alimentation en gaz ..................................... 52

Exigences concernant I'evacuation ........................................... 54

Planification du syst_me d'evacuation ...................................... 55

Installation du systeme d'evacuation ........................................ 56

Installation des pieds de nivellement ......................................... 56

Raccordement au gaz ................................................................ 57

Raccordement du conduit d'evacuation ................................... 57

Mise a niveau de la secheuse .................................................... 58

Inversion de I'ouverture de la porte ........................................... 58

Achever I'installation .................................................................. 59

UTILISATION DE LA SI:!:CHEUSE................................................ 60

Mise en marche de la secheuse ................................................ 60

Arr_t de la secheuse ................................................................... 61

Pause ou remise en marche ....................................................... 61

Verrouillage des commandes ..................................................... 61

Conseils pour le sechage et les programmes ........................... 61

Temoins lumineux ...................................................................... 62

Programmes ............................................................................... 63

Caracteristiques supplementaires ............................................. 64

Grille de sechage ........................................................................ 65

ENTRETIEN DE LA sr_OHEUSE ................................................. 66

Nettoyage de I'emplacement de la secheuse ........................... 66

Nettoyage du filtre a charpie ...................................................... 66

Nettoyage de I'interieur de la secheuse ..................................... 66

Retrait de la charpie accumulee ................................................ 67

Precautions a prendre pour les vacances et avant un

demenagement .......................................................................... 67

Changement de I'ampoule d'eclairage du tambour .................. 67

DI:!:PANNAGE................................................................................. 68

ASSISTANCE OU SERVICE ......................................................... 70

GARANTI E ..................................................................................... 71

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

i WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

In the State of Massachusetts, the following installation instructions apply: [] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type. [] A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

• Read all instructions before using the dryer.

• Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

• Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry- cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.

• Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is used near children.

• Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

• Do not reach into the dryer if the drum is moving.

• Do not install or store the dryer where it will be exposed

to the weather.

• Do not tamper with controls.

SAVE THESE INSTRUCTIONS

• Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this

Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out.

• Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

• Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

• Clean lint screen before or after each load.

• Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust,

and dirt.

• The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.

• See installation instructions for grounding requirements.

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSi Z223.1/NFPA 54 or the Canadian Natural Gas and Propane installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA O22.1.

INSTALLATION INSTRUCTIONS

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

8" or 10" pipe wrench 8" or 10" adjustable

wrench (for gas connections)

Flat-blade screwdriver Adjustable wrench that

opens to 1" (2.5 cm) or hex-head socket wrench

(for adjusting dryer feet) v4" nut driver or socket

wrench (recommended)

Parts supplied

Remove parts packages from dryer drum. Check that all parts are included.

4 Leveling legs

• Level

• Knife

• Vent clamps

• Pipe-joint compound resistant to LP gas

• Caulking gun and compound (for installing new exhaust vent)

• Pliers

• Tape measure

Parts needed

Check local codes and with gas supplier. Check existing gas supply, electrical supply and venting. Read "Electrical Requirements," "Gas Supply Requirements" and "Venting Requirements" before purchasing parts.

• For close-clearance installations between 31.5" (80.01 cm) and 37" (93.98 cm), see "Plan Vent System" section for venting requirements.

I_- 37" --_1

(93.98 crn)

Mobile home installations require special parts (listed following) that may be ordered by calling the dealer from whom you purchased your dryer. For further information, please refer to the

"Assistance or Service" section of this manual.

• Mobile Home Installation Kit. Ask for Part Number 346764.

• Metal exhaust system hardware.

NOTE: Do not use leveling legs if installing the dryer on a pedestal.

Pedestal

Are you placing the dryer on a pedestal? You may purchase a

pedestal separately for this dryer. This pedestal will add about 13" (33 cm) to the height of your unit for a total height of approximately 51" (130 cm).

For a garage installation, you will need to place the pedestal at least 6" (15.2 cm) above the floor.

Optional pedestal

To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section of this manual. Ask

for Part Number LAB2700PMT (Meteorite) or LAB2700MQ0

(White).

Stack Kit

Are you planning to stack your washer and dryer? To do so, you

will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section of this manual. Ask

for Part Number 8541503.

• A sturdy floor to support the total dryer weight of 200 Ibs (90.7 kg). The combined weight of a companion appliance

should also be considered. A level floor with a maximum slope of 1" (2.5 cm) under entire

dryer. If slope is greater than 1" (2.5 cm), install Extended Dryer Feet Kit, Part Number 279810. Clothes may not tumble properly, and automatic sensor cycles may not operate correctly if dryer is not level.

For a garage installation, you will need to place the dryer at least 18" (46 cm) above the floor. If using a pedestal, you will need to place the pedestal at least 6" (22.9 cm) above the

floor.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.

Installation clearances

• The location must be large enough to allow the dryer door to open fully.

Additional spacing should be considered for ease of installation and servicing.

Additional clearances might be required for wall, door and floor moldings.

Additional spacing of 1" (2.5 cm) on all sides of the dryer is recommended to reduce noise transfer.

Companion appliance spacing should also be considered.

Dryer Dimensions

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. A gas

dryer must be exhausted to the outdoors. See "Venting Requirements."

• If you are using a power supply cord, a grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See "Electrical Requirements."

(130.81cm)

(96.52 Cm)

'311/2"

{80 crn) 27"

*Most installations require a minimum 51/2'' (14 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting Requirements."

Minimum installation spacing for custom undercounter installation

The dimensions shown are for the minimum spacing allowed.

Custom undercounter installation - Dryer only

38" rain. I I

0cm,

'%111

0"* _ 27"--_--- 6"*

(6cm) ' (68.6cm) 6cm

*Additional spacing recommended

Minimum installation spacing for recessed or closet installation, with or without a pedestal

• The dimensions shown are for the minimum spacing allowed. For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

Closet installation - Dryer only

Minimum installation spacing for cabinet installation

• The dimensions shown are for the minimum spacing allowed. For cabinet installation, with a door, minimum ventilation

openings in the top of the cabinet are required.

" , m)

*Additional spacing recommended

**Side or bottom venting - additional spacing recommended

Recommended installation spacing for recessed or closet installation, with stacked washer and dryer

7"(17.8crn)

6"** 31W' 1" 0"* 27" 6"*

(Ocm)(80.0cra)(2.Scra) (0cm)(68.6cm)(0cm)

24 in.2

(155cm2)

I1,,_ 31,J_"_18,,*1

(2.5 crn)(80 cm) (Ocrn)

A. Side view - closet or confined area

B. Closet door with vents

*Side or bottom venting - additional spacing recommended Recessed or closet installation - Dryer on pedestal

[_ -._ 14"maK

_lif 3.

(7.6¢m)

-i

The dimensions shown are for the recommended spacing.

48 in? *

(310crn2)

3" {7.6 crn) ...........................

3" {7.6 cm) _

24 in? *

(155crn_)

*Min. top and bottom air openings for closet door

6" (1_.2 cm)

76" " • .....

-- {193cm)

-_ _- 1"(2.5crn)

T _::4\

(Ocrn) (68.6cm) (Ocrn)

*Additional spacing recommended

**Side or bottom venting - additional spacing recommended

27"

A. Recessed area B. Side view - closet or confined area

1"I1_- 31,_"--_lo"**l

(2.5crn) (80cm) (Ocm)

/ I

(14cm) {2.Scrn) _ {68.6crn) _ 2.Scrn

**External exhaust elbow requires additional spacing.

**l-Wall, door and floor molding may require additional spacing.

Mobile home - Additional installation requirements

This dryer is suitable for mobile home installations. The

installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard

CAN/CSA-Z240 MH.

Mobile home installations require:

• Metal exhaust system hardware, which is available for purchase from your dealer.

• Mobile Home Installation Kit Part Number 346764. See "Tools and Parts" section for ordering information.

Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.

Explosion Hazard

Use a new CSA international approved gas supply line.

install a shut=off valve. Securely tighten all gas connections.

If connected to LP, have a qualified person make sure gas pressure does not exceed 13" (33 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is also recommended that a separate circuit serving only this dryer be provided.

GROUNDING INSTRUCTIONS

• For a grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer is equipped with a cord having an equipment- grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes

and ordinances.

Gas Type

Natural gas:

This dryer is equipped for use with Natural gas. It is design- certified by CSA International for LP (propane or butane) gases with appropriate conversion.

• Your dryer must have the correct burner for the type of gas in your home. Burner information is located on the rating plate in the door well of your dryer. Ifthis information does not agree with the type of gas available, contact your dealer or call the phone numbers referenced in the "Assistance or

Service" section of this manual.

LP gas conversion: Conversion must be made by a qualified technician.

No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting your gas company.

Gas supply line

• 1/2"IPS pipe is recommended. %" approved tubing is acceptable for lengths under

20 ft (6.1 m) if local codes and gas supplier permit. Must include 1/8"NPT minimum plugged tapping accessible

for test gauge connection, immediately upstream of the gas connection to the dryer (see following illustration).

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

• Must include a shutoff valve: In the U.S.A.: An individual manual shutoff valve must be installed within

six (6)feet (1.8 m)of the dryer in accordance with the National Fuel Gas Code, ANSI Z223.1.

In Canada: An individual manual shutoff valve must be installed in

accordance with the B149.1, Natural Gas and Propane Installation Code. It is recommended that an individual

manual shutoff valve be installed within six (6) feet (1.8 m) of the dryer.

The location should be easy to reach for opening and closing.

A C E

B D

A. %" flexible gas connector

B. %" pipe to flare adapter fitting C. Vs"NPT minimum plugged tapping D. _/2"NPT gas supply line

E. Gas shutoff valve

Gas supply connection requirements

• For close clearances, a 3/8"to 3/8"elbow is recommended to avoid kinking of the gas line.

• Use only pipe-joint compound. Do not use TEFLON _t tape.

There are many methods by which your gas dryer can be

connected to the gas supply. Listed here are some guidelines for

two different methods of connection.

Option 1 (Recommended method)

Flexible stainless steel gas connector:

• If local codes permit, use a new flexible stainless steel gas connector (Design Certified by CSA International) to connect your dryer to the rigid gas supply line. Use an elbow and a %" flare x %" NPT adapter fitting between the stainless steel gas connector and the dryer gas pipe, as needed to avoid kinking.

Option 2 (Alternate method)

Approved aluminum or copper tubing:

• Lengths under 20 ft (6.1 m) can use 3/8"approved tubing (if codes and gas supplier permit).

• If you are using Natural gas, do not use copper tubing.

• %" flare x %" NPT adapter fitting between dryer pipe and %" approved tubing.

• Lengths over 20 ft (6.1 m) should use larger tubing and a different size adapter fitting.

• If your dryer has been converted to use LP gas, %" LP compatible copper tubing can be used. If the total length of the supply line is more than 20 ft (6.1 m), use larger tubing.

NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON °t tape.

Burner input requirements

Elevations up to 10,000 ft (3,048 m):

• The design of this dryer is certified by CSA International for use at altitudes up to 10,000 ft (3,048 m) above sea level at

the B.T.U. rating indicated on the model/serial number plate. Burner input adjustments are not required when the dryer is operated up to this elevation.

Elevations above 10,000 ft (3,048 m):

• When installed above 10,000 ft (3,048 m) a 4% reduction of the burner B.T.U. rating shown on the model/serial number plate is required for each 1,000 ft (305 m) increase in

elevation.

Gas supply pressure testing

• The dryer must be disconnected from the gas supply piping system during pressure testing at pressures greater than 1/2psi.

Dryer gas pipe

• The gas pipe that comes out through the rear of your dryer has a %" male pipe thread.

A. 7/2"NPT gas supply line

B. %" NPT dryer pipe

*NOTE: Ifthe dryer is mounted on a pedestal, the gas pipe height

must be an additional 13" (33 cm) from the floor. For a garage installation, the gas pipe height must be an additional

18" (46 cm) from the floor.

t®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Fire Hazard

Use a heavy metal vent. Do not use a plastic vent.

Do not use a metal foil vent. Failure to fellow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling or a concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint.

• Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

• Review Vent system chart. Modify existing vent system if necessary to achieve the best drying performance.

• Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance.

• Do not install flexible metal vent in enclosed walls, ceilings or floors.

Elbows

45° elbows provide better airflow than 90° elbows.

J J

Good Better

Clamps

• Use clamps to seal all joints.

• Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the

duct. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be used. DURASAFE TM venting products are recommended.

4" (10.2cm) heavymetal exhaust vent

DURASAFE TM vent products can be purchased from your dealer or by calling Whirlpool Parts and Accessories. For more information, see the "Assistance or Service" section of

this manual.

Rigid metal vent

• For best drying performance, rigid metal vents are recommended.

• Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for cleaning.

• Flexible metal vent must be fully extended and supported when the dryer is in its final location.

(10.2 cm)

A. Louvered hood style

B.Box hood style

The angled hood style (shown here) is acceptable.

(6.4 cm)

• An exhaust hood should cap the vent to keep rodents and insects from entering the home.

• Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).

• Do not use an exhaust hood with a magnetic latch.

improper venting can cause moisture and lint to collect indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint,

wallpaper, carpets, etc.

[] Housecleaning problems and health problems.

Choose your exhaust installation type

Recommended exhaust installations

Typical installations ventthe dryer from the rearof the dryer.

Other installations arepossible.

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown.

Refer to the manufacturer's instructions.

! t.;

T===j/

A--

E F

, ........................................G

..................................H

A. Dryer E. Clamps B. Elbow F. Rigid metal or flexible metal vent

C. Wall G. Vent length necessary to connect D. Exhaust hood elbows

H. Exhaust outlet

Optional exhaust installations

This dryer can be converted to exhaust out the right side, left side

or through the bottom. If you prefer, you may contact your local dealer to have the dryer converted.

Fire Hazard

Cover unused exhaust holes with one of the

following kits:

279818 (white) 280028 (meteorite)

Contact your local dealer. Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

A B

A. Over-the-top installation (also available with one

offset elbow)

B. Periscope installation

NOTE: The following kits for close clearance alternate installations are available for purchase. Please see the

"Assistance or Service" section of this manual to order.

• Over-the-Top Installation: Part Number 4396028

• Periscope Installation (For use with dryer vent to wall vent mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm) mismatch

Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm) mismatch

Special provisions for mobile home installations The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside.

A B

A. Standard rear offset exhaust installation B. Left or right side exhaust installation

C. Bottom exhaust installation

Determine vent path

• Select the route that will provide the straightest and most direct path outdoors.

• Plan the installation to use the fewest number of elbows and turns.

• When using elbows or making turns, allow as much room as possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90 ° turns possible.

Determine vent length and elbows needed for best drying performance

• Use the Vent system chart below to determine type of vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those

specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that will

help to achieve the best drying performance.

Excessive Weight Hazard

Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

1. To protect the floor, use a large flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer.

2. Firmly grasp the body of the dryer. Gently lay the dryer on the cardboard. See illustration.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add one 90° turn to the chart.

Number of Type of Box or Angled

90° turns vent Iouvered hoods or elbows hoods

0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)

Flexible metal 36 ft (11 m) 28 ft (8.5 m)

1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m)

Flexible metal 27 ft (8.2 m) 19 ft (5.8 m)

3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)

Flexible metal 25 ft (7.6 m) 17 ft (5.2 m)

4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m)

Flexible metal 23 ft (7 m) 15 ft (4.6 m)

Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.

Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in "Plan Vent System." Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior

of the vent to secure vent.

3. Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to

finish turning the legs until the diamond marking is no longer visible.

5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent or gas line.

For mobile home use

Gas dryers must be securely fastened to the floor at the time of installation.

Mobile home installations require a Mobile Home Installation Kit. For more information, please reference the service numbers in

the "Assistance or Service" section of this manual.

Remove the red cap from the gas pipe.

Using a wrench to tighten, connect the gas supply to the dryer. Use pipe-joint compound on the threads of all non- flared male fittings, If flexible metal tubing is used, be sure

there are no kinks.

A............................._ _ ............................B

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Make sure that there are no kinks in the flexible gas line.

4. Once the exhaust vent connection is made, remove the corner posts and cardboard.

A. Flared male fitting B, Non-flared male fitting

NOTE: For LP gas connections, you must use pipe-joint compound resistant to the action of LP gas. Do not use TEFLON °t tape.

A combination of pipe fittings must be used to connect the dryer to the existing gas line. Shown is a recommended connection. Your connection may be different, according to the supply line type, size and location.

A. %" flexible gas connector

B. %" dryerpipe C. %" to @"pipe elbow D. %" pipe-to-flare adapter fitting

Open the shutoff valve in the supply line. The valve is open when the handle is parallel to the gas pipe.

Check the levelness of the dryer. Check levelness first side to side, then front to back.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for

levelness.

.....'_ _ s_

You can change your door swing from a right-side opening to a left-side opening, if desired.

Remove the door

1. Open the dryer door. Remove the 4 screws that hold the door hinge on the front panel of the dryer. Loosen, but do not remove, the screw with the top keyhole opening last (second from the top).

A. Closed valve

B.Open valve

Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

t®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

A, Dryer B, De net remove.

C. Dryer door

Lift and pull forward on the door so that the keyhole clears the screw head. Remove the door.

Lay the dryer door on a flat, protected surface with the inside door assembly facing up. Remove the last screw from Step 1. Remove the 2 screws holding the handle to the door.

Remove the 6 screws to release the outer door assembly from the inner door assembly (see illustration). It is important

that you remove only the 6 indicated screws.

Reverse the hinge and hinge bracket

1. Place the inner door, screw head side up, on the work surface.

2. Remove the 4 screws that hold the hinge to the door.

3. Remove the 2 screws that hold the handle bracket to the door.

Lift the inner door assembly off of the outer door assembly. Unsnap the handle from the outer door assembly, move it to the other side, and snap in. Set the outer door assembly

aside.

4. Move hinge to the other side and reattach with the 4 screws removed in Step 2.

5. Move handle bracket to the other side and reattach with the 2 screws removed in Step 3.

6. Set the inner door assembly aside.

Reinstalling the door

1. Check for fingerprints on the glass. Clean if necessary.

2. Place the inner door assembly into the outer door assembly. Align the hinge in the opening on the side. To fit correctly, the inside door assembly edge is completely inside the outside door assembly edge.

3. Reassemble the inner and outer door assemblies with the 6 screws.

Replace the 2 handle screws for the door handle of the door assembly.

Use a small flat-blade screwdriver to remove plug strip in the door opening. Slide the head of the screwdriver under the top portion of the plug strip, being certain not to scratch the dryer surface. Lift up. Repeat in the middle and at the bottom. Remove the plug stripe in the door opening and insert in the opposite side.

Insert a screw in the second opening from the top of the hinge opening and partially tighten. Hang the door by placing

the top hinge keyhole over the second screw head and tighten the screw. By putting this screw in first, the door will

hang in place while you insert and tighten the remaining 4 screws.

f. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check the dryer's final location. Be sure the vent is not crushed or kinked.

5. Check that the dryer is level. See "Level Dryer."

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord, Failure to follow these instructions can result in death,

fire, or electrical shock.

A. Dryer door B. Dryer

C. Insert this screw first.

7. Close the door and check that it latches securely.

Plug into a grounded 3 prong outlet. Turn on power.

Remove any protective film or tape remaining on the dryer.

Read "Dryer Use."

Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

10.

Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Only modifier.

If the dryer will not start, check the following:

• Dryer is plugged into a grounded 3 prong outlet.

• Electrical supply is connected.

• Household fuse is intact and tight, or circuit breaker has

not tripped.

• Dryer door is closed.

11.

When the dryer has been running for 5 minutes, open the dryer door and feel for heat. Ifyou feel heat, cancel cycle and close door. If you do not feel heat, turn off the dryer and check that the gas supply line shutoff valve is open.

• If the gas supply line shutoff valve is closed, open it, then

repeat the 5-minute test as outlined above.

• If the gas supply line shutoff valve is open, contact a

qualified technician.

DRYER USE

CONTROL ON O

Sensing 0

Wet 0

Damp 0

Cool Down 0

Cycle Complete 0

Extra Care 0

Cont*ol Locked 0

Delicate

Heavy Duty

Normal

Casua_

AUTOMATIC

_CYCLI_S_._

MANUAL Estimated Time ¢O High

Timed Dry Remaln_ng p Medium

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

ANU DRYNESS TEMP EXTRA CYCLE

DRY TIME LEVEL CARE EI_NDL_..,,

o o o o

lock / u_+lock Pause

controJ

Fire Hazard

No washer can completely remove oil. Do not dry anything that has ever had any type of oil on

it (including cooking oils). items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle. Failure to follow these instructions can result in death

or fire.

The following is a guide to starting your dryer. Please refer to

specific sections of this manual for more detailed information.

1. Clean lint screen before each load. See "Cleaning the Lint Screen."

2. Place laundry into dryer and shut door.

3. Rotate the dial to select either an Automatic or Manual Cycle then press the CONTROL ON button. The preset settings and

drying time for the cycle chosen will be displayed.

To use an Automatic Cycle

Point the dial to an Automatic Cycle. Select DRYNESS LEVEL to adjust how dry you want the

load to be. The time displayed is an estimated length of the cycle based on the Dryness Level selected. As the

cycle runs, the control senses the dryness of the load and adjusts the time automatically for the selected Dryness

Level.

Less

I ore

DRYNESS

LEVEL

NOTE: Time is not adjustable for Automatic Cycles. Pressing the Manual Dry Time (- or +) buttons will cause a triple beep, indicating that the time cannot be changed.

• Press the EXTRA CARE feature button if this option is desi red.

• Press the CYCLE END SIGNAL button to set signal volume to desired level.

• Press (and hold) HOLD TO START button until dryer starts (about 1 second).

Once an Automatic Cycle has started, the Extra Care feature and the Cycle End Signal level can be adjusted. Press the

OFF key twice to stop the dryer and clear the settings, allowing you to select another cycle and Dryness Level.

How Auto Moisture Sensing Plus works

The Even-Heat TM feature improves drying performance with Auto Moisture Sensing Plus, which advances the cycle as moisture is extracted from clothing. A thermistor (electronic temperature sensor) and moisture sensing strips in the dryer drum help measure the amount of moisture in the clothes as they pass. An electronic control determines the load type to help save time, avoid overdrying, and increase the accuracy of the end dryness level. After the first 5 minutes of an automatic cycle, the estimated time display will adjust based on the approximate load size, cycle, dryness level selected

and amount of moisture left in the clothes. When the clothes have reached approximately 80% of the dryness level

selected, the estimated time display will adjust again, showing the final drying time. Auto Moisture Sensing Plus takes the guesswork out of drying time and enhances fabric

care.

To use a Manual Cycle

• Rotate the dial to select a Manual Cycle. Press the MANUAL DRY TIME (- or +) buttons until the

desired drying time is displayed. Tap - or +, and the time will change by 1-minute intervals. Press and hold - or +, and the time will change by 5-minute intervals. The initial time displayed is the actual drying time.

NOTE: The Manual Dry Time feature can be used only with Manual Cycles.

• Press TEMP until the desired temperature glows. NOTE: Pressing the Dryness Level button will cause the triple

beep indicating that this option is not selectable. Also, a Dryness Level is not indicated.

• Press the EXTRA CARE feature button if this option is desired.

Press the CYCLE END SIGNAL button to set volume to desired level.

Press (and hold) HOLD TO START button until dryer starts (about 1second).

While a Manual Cycle is running, you can change the settings for Time, Temperature, the Extra Care feature, and the Cycle

End Signal. Press the OFF button twice to stop the dryer and clear the settings, allowing you to select another cycle.

To stop your dryer at any time Press OFF twice or open the door.

To pause the dryer at any time Open the door or press OFF once.

To restart the dryer Close the door and press (and hold) HOLD TO START button until

dryer starts. NOTE: Drying will continue from where the cycle was interrupted

if you close the door and press Start within 5 minutes, Ifthe cycle is interrupted for more than 5 minutes, the dryer will shut off. Select new cycle settings before restarting the dryer.

This feature allows you to lock your settings to avoid unintended use of the dryer. You can also use the Control Locked feature to avoid unintended cycle or option changes during dryer operation.

To enable the Control Locked feature when dryer is running:

Press and hold the CYCLE END SIGNAL button for 3 seconds. The control is locked when a single beep is heard and the Control

Locked status light is on.

• When the dryer is off, it is not necessary to press the Control On button before activating the Control Locked feature.

To unlock:

Press and hold the CYCLE END SIGNAL button for 3 seconds to turn this feature off.

NOTE: When the dryer is running and Control Locked is on, the dryer can be stopped by pressing the Off button, but can't be

restarted until the control is unlocked.

.... t:;, _,(_ } s,;',r_

Select the correct cycle and dryness level or temperature for your load. If an Automatic Cycle is running, the display shows the estimated cycle time when your dryer is automatically sensing the dryness level of your load. If a Manual Cycle is running, the

display shows the exact number of minutes remaining in the cycle.

Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to

handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level.

Drying tips

• Follow care label directions when they are available.

• If desired, add a fabric softener sheet. Follow package instructions.

• Remove the load from the dryer as soon as tumbling stops to reduce wrinkling. This is especially important for permanent press, knits and synthetic fabrics.

• Avoid drying heavy work clothes with lighter fabrics. This could cause overdrying of lighter fabrics, leading to increased shrinking or wrinkling.

Cycle tips

• Dry most loads using the preset cycle settings.

• Refer to the Automatic or Manual Preset Cycle Settings chart (in the "Cycles" section) for a guide to drying various loads.

Drying temperature and Dryness Level are preset when you choose an Automatic Cycle. You can choose a different dryness level, depending on your load by pressing the DRYNESS LEVEL button to select MORE or

LESS.

• If you wish to adjust the cycle length of a Manual Cycle,

you must press the MANUAL DRY TIME (- or +) buttons. Adjust the temperature of a Manual Cycle by pressing TEMP until the desired temperature is selected.

NOTE: You cannot choose a Dryness Level with Manual Cycles.

You may follow the progress of your dryer with the drying status indicator lights.

Sensing O

Wet O

Damp 0

Cool Down 0

CycleComplete 0

ExtraCare 0

Control Locked 0

Sensing

When a cycle is first turned on, the Sensing light glows until a wet item is detected.

• In an Automatic Cycle, if a wet item has not been detected within 10 minutes, the Sensing light will turn off and the dryer

will shut down.

• In a Manual Cycle, if a wet item is not detected after 10 minutes the Wet light turns on and the selected cycle

continues.

Wet The Wet light will turn on when a wet item has been detected in

the dryer. The Wet light will remain on until:

• The damp dry point is reached in an Automatic Cycle.

• The dryer enters the cool down period in a Manual Cycle.

Damp

The Damp light indicates that the load has reached the damp dry

level. NOTE: The Damp light is not used with Manual Cycles.

Cool Down

The Cool Down light glows during the cool down part of the

cycle. Laundry is cooling down for ease in handling.

Select the drying cycle that matches the type of load you are drying. See Automatic preset or Manual preset cycle settings

charts.

AUTOMATIC

Heavy Duty

NorrnaJ

Casual

Delicate _ _O

Super _J

Delicate

CYCLES

MANUAL

Timed Dry

Touchup

I Rapid Dry

Cycle control knob

Automatic Cycles allow you to match the cycle to the load you are drying. See the following Automatic preset cycle settings chart. Each cycle dries certain fabrics at the recommended temperature. A sensor detects the moisture in the load and automatically adjusts the drying time for optimal drying.

Heavy Duty

Use this cycle to get High heat for heavy fabrics such as cotton towels or bedspreads.

Normal

Use this cycle to get Medium heat for drying sturdy fabrics such as work clothes.

Casual Use this cycle to get Medium heat for drying no-iron fabrics such

as sport shirts, casual business clothes and permanent press blends.

Delicate

Use this cycle to get Low heat for drying synthetic fabrics, washable knit fabrics and no-iron finishes.

Cycle Complete

The Cycle Complete light glows when a drying cycle is finished. If the Extra Care feature has been selected, the Extra Care feature

indicator light will also be on.

The Cycle Complete light turns off 1 hour after the end of a drying

cycle (including the Extra Care cycle of 2 hours), when Off is pressed, or when the door is opened.

Extra Care Feature

The Extra Care feature light glows when this option is selected. This indicator stays on with the Cycle Complete light.

Control Locked

The Control Locked light glows when this option is enabled.

Indicator lights

Other indicator lights on the control panel show Cycle,

Temperature and Cycle End Signal settings selected. The time display will indicate the estimated or actual time

remaining in a cycle.

Super Delicate Use this cycle to get Extra-Low heat to gently dry items such as

lingerie, exercise wear or sheer curtains.

Automatic preset cycle settings

Automatic Cycles Temp. Time*

Load Type (Minutes)

HEAVY DUTY High 40

Heavyweight, towels

NORMAL Medium 34

Corduroys, work clothes

CASUAL Medium 36

Permanent press, synthetics

DELICATE Low 28 Lingerie, blouses, washable

woolens

SUPER DELICATE Extra Low 22

Exercise wear, sheer curtains, lace

*Estimated Time with Dryness Level (medium) setting.

Use Manual Cycles to select a specific amount of drying time and a drying temperature. When a Manual Cycle is selected, the ESTIMATED TIME REMAINING display shows the actual time remaining in your cycle. You can change the actual time in the cycle by pressing the Manual Dry Time (- or +) buttons.

Timed Dry

Use this cycle to complete drying if items are still damp after an

Automatic Cycle. Timed Dry is also useful for drying heavyweight

and bulky items, such as bedspreads and work clothes.

Temperature

Temperature settings are used with the Manual Cycles. Press TEMP until the desired temperature setting glows. Temperature settings cannot be used with the Automatic Cycles.

oO Medium

Low

Extra Low

IO High

Air Only

Touchup

Use this setting to help smooth out wrinkles from such items as clothes packed in a suitcase or items wrinkled from being left in

the dryer too long.

Rapid Dry

Use this cycle for drying small loads or loads that need a short drying time.

Manual preset cycle settings

Manual Cycles Temp. Default Time Load Type (Minutes)

TIMED DRY High 40

Heavyweight, bulky items,

bedspreads, work clothes

TOUCHUP Medium 20

Helps to smooth out

wrinkles

RAPID DRY High 27

Small loads

Extra Care Feature When you are unable to remove a load of clothes from the dryer

as soon as it stops, wrinkles can form. The Extra Care feature periodically tumbles, rearranges and fluffs the load to help reduce wrinkling.

• Press the Extra Care feature to get up to 120 minutes of heat- free, periodic tumbling at the end of a cycle.

• Stop at any time by pressing the Extra Care feature or opening the dryer door.

For the Casual Cycle, the Extra Care feature is preset to "On." The other Automatic Cycles will retain the Extra Care feature setting. (For example, if you select the Extra Care feature in the Normal cycle, the Extra Care feature will be on the next time you select the Normal cycle.)

NOTE: Ifyou do not select the Extra Care feature, the dryer stops after the cool down period.

TEMP

Air Only

Use the Air Only setting for items that require drying without heat such as rubber, plastic and heat-sensitive fabrics. This chart shows examples of items that can be dried using Air Only.

Type of Load Time*

(Minutes)

Foam rubber - pillows, padded bras, 20 - 30 stuffed toys

Plastic - Shower curtains, tablecloths 20 - 30

Rubber-backed rugs 40 - 50

Olefin, polypropylene, sheer nylon 10 - 20

*Reset time to complete drying, if needed.

When using Air Only

• Check that coverings are securely stitched.

• Shake and fluff pillows by hand periodically during the cycle.

• Dry item completely. Foam rubber pillows are slow to dry. NOTE: Automatic Cycles are not available when using the Air

Only setting.

Cycle End Signal

The Cycle End Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the cycle reduces wrinkling.

Loud 0"_

SoftOI

offorJ

CYCLE

END

SIGNAL Ho(d for 3

seconds to

(ocl</ un(ock

contro(

Press and release the CYCLE END SIGNAL to adjust the sound level or turn off the signal.

NOTE: When the Extra Care feature is selected and the Cycle End Signal is on, an audible sound will emit every 5 minutes until

the clothes are removed, or the Extra Care feature is finished.

The drying rack is useful for drying items you would not

necessarily want to tumble dry or that you would normally line dry (for example, sweaters).

To use the drying rack

Do not remove the lint screen. f. Open dryer door.

This chart shows examples of items that can be rack dried and the suggested cycle, temperature setting and drying time. Actual drying time will depend on the amount of moisture items hold.

Rack Dry Setting Temp. Time*

Wool Sweaters Timed Low 60

Block to shape and lay flat on Dry the rack

Stuffed toys or pillows Timed Low 60 Cotton or polyester fiber filled Dry

Stuffed toys or pillows Timed Air Only 90 Foam rubber filled Dry (no

heat)

A. Front edge

2. Place drying rack inside dryer drum, positioning the back wire on the ledge of the inner dryer back panel. Push down on

front edge of drying rack to secure over the lint screen.

A. Dryer rack front edge

B. Dryer back panel

3. Put the wet items on top of the rack. Leave space between the items so air can reach all the surfaces.

NOTE: Do not allow items to hang over the edge of the rack.

4. Close the door.

5. Select a timed drying cycle and temperature, or an air cycle (see following chart). Items containing foam, rubber or plastic must be dried on a clothesline or by using the Air Only temperature setting.

6. You must select a time by pressing the MANUAL DRY TIME (- or +) buttons. Reset time as needed to complete drying. Refer to the following table.

7. Press (and hold) HOLD TO START button (about 1 second).

NOTE: You must remove rack for normal tumbling. Do not use automatic cycles with the drying rack.

Sneakers or canvas shoes Timed Air Only 90

Dry (no

heat)

*(Minutes) Reset time to complete drying, if needed.

DRYER CARE

Keep dryer area clear and free from items that would obstruct the flow of combustion and ventilation air.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer,

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

C ca-@ g c ,

Every load cleaning

The lint screen is located in the door opening of the dryer. A screen blocked by lint can increase drying time.

To clean

Pull the lint screen straight up. Roll lint off the screen with your fingers. Do not rinse or wash screen to remove lint. Wet

lint is hard to remove.

2. Push the lint screen firmly back into place.

IMPORTANT:

• Do not run the dryer with the lint screen loose, damaged, blocked or missing. Doing so can cause overheating and damage to both the dryer and fabrics.

• If lint falls off the screen into the dryer during removal, check the exhaust hood and remove the lint. See "Venting Requirements."

As needed cleaning

Laundry detergent and fabric softener residue can build up on the lint screen. This buildup can cause longer drying times for your clothes, or cause the dryer to stop before your load is completely dry. The screen is probably clogged if lint falls off the screen.

Clean the lint screen with a nylon brush every 6 months, or more

frequently, if it becomes clogged due to a residue buildup.

To wash

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent. Scrub lint screen with the brush to remove residue buildup.

Vacation care

Operate your dryer only when you are at home. If you will be on vacation or not using your dryer for an extended period of time, you should:

1. Unplug dryer or disconnect power.

2. Close shutoff valve in gas supply line.

3. Clean lint screen. See "Cleaning the Lint Screen."

Moving care

1. Unplug the power supply cord.

2. Close shutoff valve in gas supply line.

3. Disconnect gas supply line pipe and remove fittings attached to dryer pipe.

4. Cap the open fuel supply line.

5. Make sure leveling legs are secure in dryer base.

6. Use masking tape to secure dryer door.

...... , ,_

The dryer light automatically turns on inside the dryer drum when you open the door.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Replace screen in dryer.

To clean dryer drum

1. Make a paste with powdered laundry detergent and very warm water.

2. Apply paste to a soft cloth. OR

Apply a liquid, nonflammable household cleaner to the stained area and rub with a soft cloth until all excess dye and

stains are removed.

3. Wipe drum thoroughly with a damp cloth.

4. Tumble a load of clean cloths or towels to dry drum.

NOTE: Garments that contain unstable dyes, such as denim blue

jeans or brightly colored cotton items, may discolor the dryer

interior. These stains are not harmful to your dryer and will not stain future loads of clothes. Dry unstable dye items inside out to avoid dye transfer.

From Inside the Dryer Cabinet Lint should be removed every 2 years, or more often, depending

on dryer usage. Cleaning should be done by a qualified person.

To change the drum light

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the back wall of the dryer. Remove the screw located in the lower right

corner of the cover. Remove the cover.

3. Turn bulb counterclockwise. Replace the bulb with a 10-watt appliance bulb only. Replace the cover and secure with the

screw.

4. Plug in dryer or reconnect power.

From the Exhaust Vent Lint should be removed every 2 years, or more often, depending

on dryer usage.

TROUBLESHOOTING

Firsttry the solutions suggested here and possibly avoid the cost of a service call...

Dryer will not run

Has a household fuse blown, or has a circuit breaker tripped?

There may be 2 fuses or circuit breakers for the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.

• Was a regular fuse used? Use a time-delay fuse.

• Is the dryer door firmly closed?

• Was the Start button firmly pressed? Large loads may require pressing and holding the Start button for 2-5 seconds.

No heat

Has a household fuse blown, or has a circuit breaker tripped?

The drum may be turning, but you may not have heat. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.

• Is the valve open on the gas supply line?

Unusual sounds

• Has the dryer had a period of non-use? If the dryer hasn't been used for a while, there may be a thumping sound during the first few minutes of operation.

Is a coin, button, or paper clip caught between the drum and front or rear of the dryer?

Check the front and rear edges of the drum for small objects. Clean out pockets before laundering.

• Is it a gas dryer? The gas valve clicking is a normal operating sound.

Are the four legs installed, and is the dryer level front to back and side to side?

The dryer may vibrate if not properly installed. See "Installation Instructions."

• Is the clothing knotted or balled up? When balled up, the load will bounce, causing the dryer to vibrate. Separate the load items and restart the dryer.

Clothes are not drying satisfactorily, drying times are too long, or load is too hot

• Is the lint screen clogged with lint? Lint screen should be cleaned before each load.

Fire Hazard

Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to follow these instructions can result in death

or fire.

• Is the exhaust vent or outside exhaust hood clogged with

lint, restricting air movement?

Run the dryer for 5-10 minutes. Hold your hand under the outside exhaust hood to check air movement. If you do not feel air movement, clean exhaust system of lint or replace exhaust vent with heavy metal or flexible metal vent. See

"Installation Instructions."

• Are fabric softener sheets blocking the grille? Use only one fabric softener sheet, and use it only once.

• Is the exhaust vent the correct length? Check that the exhaust vent is not too long or has too many turns. Long venting will increase drying times. See

"Installation Instructions."

• Is the exhaust vent diameter the correct size? Use 4" (10.2 cm) diameter vent material.

Dryer displaying code message

• "PF" (power failure), check the following: Was the drying cycle interrupted by a power failure? Press and hold START to restart the dryer.

• "E" Variable (El, E2, E3) service codes: Call for service.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

• Is the dryer located in a room with temperature below 45°F (7°0)?

Proper operation of dryer cycles requires temperatures above 45°F (7°C).

Is the dryer located in a closet? Closet doors must have ventilation openings at the top and bottom of the door. For most installations, the rear of the dryer requires 51/2'' (14 cm). See "Installation Instructions."

Has an air dry cycle been selected? Select the right cycle for the types of garments being dried. See "Cycles."

Is the load too large and heavy to dry quickly? Separate the load to tumble freely.

Cycle time too short

Lint on load

• Is the lint screen clogged? Clean lint screen. Check for air movement.

Stains on load or drum

• Was dryer fabric softener properly used? Add dryer fabric softener sheets at the beginning of the cycle.

Fabric softener sheets added to a partially dried load can stain your garments.

Drum stains are caused by dyes in clothing (usually blue jeans). This will not transfer to other clothing.

Excessive Weight Hazard Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

• Is the automatic cycle ending early? The load may not be contacting the sensor strips. Level the dryer.

Change the dryness level setting on Automatic Cycles. Increasing or decreasing the dryness level will change the

amount of drying time in a cycle.

ASSISTANCE OR SERVICE

Before calling for assistance or service, please check "Troubleshooting." It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you use only factory specified parts. Factory specified parts will fit right and work right because they are made with the same

precision used to build every new KITCHENAID ® appliance.

To locate factory specified parts in your area, call our Customer

experience Center telephone number or your nearest designated service center.

Call the KitchenAid Customer eXperience Center

toll free: 1-800-422-1230.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing impaired, limited vision, etc.).

Referrals to local dealers, repair parts distributors and service companies. KitchenAid designated service technicians are trained to fulfill the product warranty and provide after- warranty service, anywhere in the United States.

To locate the KitchenAid designated service company in your area, you can also look in your telephone directory Yellow

Pages.

Loads are wrinkled

• Was the load removed from dryer at the end of the cycle?

• Was the dryer overloaded? Dry smaller loads that can tumble freely.

Odors

• Have you recently been painting, staining or varnishing in the area where your dryer is located?

If so, ventilate the area. When the odors or fumes are gone from the area, rewash and dry the clothing.

For further assistance If you need further assistance, you can write to KitchenAid with

any questions or concerns at:

KitchenAid Brand Home Appliances Customer experience Center

553 Benson Road Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

Call the KitchenAid Canada Customer Interaction Centre toll free:

1-800-807-6777. Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Referrals to local dealers, repair parts distributors and service companies. KitchenAid Canada designated service technicians are trained to fulfill the product warranty and provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to KitchenAid Canada with any questions or concerns at:

Customer Interaction Centre KitchenAid Canada 1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

+ 50 hidden pages