KitchenAid KFRU361VSS00, KFRU368VSS00, KFRU488VSS00, KFRU271VSS00 Installation Guide

®itchen kid ®

FREESTANDING OLUDOOR GRILLS

(;_IIIII(?

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

In Canada, for assistance, installation and service, call: 1-800-807-6777

or visit our website at www.kitchenaid.com

or visit our website at www.KitchenAid.ca

GRILS D'EXTERIEUR AUTOPORTANTS

I[I,;_II_._.._.l(.lllSQ ll,;_llhlll(.ll ..........' ° .... ,,.,_._,............._..............=_,......

Au Canada, pourassistance,installationou servicecomposez le1-800-807-6777

Table of Contents/Table des matieres ............................................................................. 4

ou visitez notre site Web & www.KitchenAid.ca

iMPORTANT:

Save for local electrical inspector's use. Jnstaler: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

iMPORTANT:

_, conserver pour consultation par I'inspecteur local des installations 61ectriques.

Instalateur : Remettre les instructions d'installation au propri6taire. Propri6taire : Conserver les instructions d'installation pour r6f6rence ult6rieure.

Models/Modeles

KFRU271VSS, KFRU361VSS, KFRU365VSS, KFRU368VSS, KFRU488VSS,

KFRS271TSS, KFRS361TSS, KFRS365TSS, KFRU368TSS, KFRU488TSS

W10175731A

OUTDOOR GRILL SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

_b, DANGER

If you smell gas:

1. Shut off gas to the appliance.

_, WARNING

1. Do not store or use gasoline or other

flammable liquids or vapors in the vicinity of this or any other appliance.

2. Extinguish any open flame.

2. An LP cylinder not connected for use

3. Open lid.

4. If odor continues, keep away from the

shall not be stored in the vicinity of this or any other appliance.

appliance and immediately call your

gas supplier or your fire department.

State of California Proposition 65 Warnings: WARNING: This product contains a chemical known to the State of California to cause cancer.

WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.

In the State of Massachusetts, the following installation instructions apply: [] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type. [] A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT: This grill is manufactured for outdoor use only. For grills that are to be used at elevations above 2000 ft (609.6 m) orifice conversion is required. See "Gas Supply Requirements" section. It is the responsibility of the installer to comply with the minimum

installation clearances specified on the model/serial rating plate. The model/serial rating plate for freestanding models can be found on the right-hand inside cabinet wall.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electrical shock,

injury to persons, or damage when using the outdoor cooking gas appliance, follow basic precautions, including the

following:

[] Do not install portable or built-in outdoor cooking gas

appliances in or on a recreational vehicle, portable trailer, boat or in any other moving installation.

[] Always maintain minimum clearances from combustible

construction, see "Location Requirements" section.

[] The outdoor cooking gas appliance shall not be located

under overhead unprotected combustible construction.

[] This outdoor cooking gas appliance shall be used only

outdoors and shall not be used in a building, garage, or any other enclosed area.

[] Keep any electrical supply cord and fuel supply hose away

from any heated surfaces.

[] Keep outdoor cooking gas appliance area clear and free

from combustible materials, gasoline and other flammable vapors and liquids.

[] Do not obstruct the flow of combustion and ventilation air.

Keep the ventilation openings of the cylinder enclosure free and clear from debris.

[] Inspect the gas cylinder supply hose before each use of the

outdoor cooking gas appliance. If the hose shows excessive abrasion or wear, or is cut, it MUST be replaced

before using the outdoor cooking gas appliance. Contact

your dealer and use only replacement hoses specified for

use with the outdoor cooking gas appliance.

[] Visually check the burner flames. They should be blue.

Slight yellow tipping is normal for LP gas.

[] Check and clean burner/venturi tube for insects and insect

nest. A clogged tube can lead to fire under the outdoor

cooking gas appliance.

[] The LP gas supply cylinder to be used must be:

- constructed and marked in accordance with the Specification for LP Gas Cylinders of the U.S. Department

of Transportation (DOT) or the National Standard of Canada, CAN/CSA-B339, Cylinders, Spheres, and Tubes

for Transportation of Dangerous Goods; and Commission.

- provided with a listed overfilling prevention device.

- provided with a cylinder connection device compatible

with the connection for outdoor cooking gas appliances.

[] Always check connections for leaks each time you connect

and disconnect the LP gas supply cylinder. See "Installation Instructions" section.

[] When the outdoor cooking gas appliance is not in use, the

gas must be turned off at the supply cylinder.

[] Storage of an outdoor cooking gas appliance indoors is

permissible only if the cylinder is disconnected and removed from the outdoor cooking gas appliance.

[] Cylinders must be stored outdoors and out of the reach of

children and must not be stored in a building, garage, or any other enclosed area.

[] The pressure regulator and hose assembly supplied with

the outdoor cooking gas appliance must be used. A replacement pressure regulator and hose assembly

specific to your model is available from your outdoor cooking gas appliance dealer.

[] Gas cylinder must include a collar to protect the cylinder

valve.

[] For appliances designed to use a CGA791 Connection:

Place a dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on

the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage

of propane.

If the following information is not followed exactly, a fire

causing death or serious injury may occur. [] Do not store a spare LP gas cylinder under or near this

outdoor cooking gas appliance.

[] Never fill the cylinder beyond 80 percent full.

SAVE THESE

iNSTRUCTiONS

TABLEOF CONTENTS

TABLE DES MATIERES

OUTDOOR GRILL SAFETY ............................................................ 2

INSTALLATION REQUIREMENTS ................................................ 5

Tools and Parts ............................................................................ 5

Location Requirements ................................................................ 5

Product Dimensions .................................................................... 6

Electrical Requirements ............................................................... 6

Gas Supply Requirements ........................................................... 7

Gas Connection Requirements .................................................... 7

INSTALLATION INSTRUCTIONS .................................................. 9

Freestanding Outdoor Grill Installation ........................................ 9

GAS CONVERSIONS .................................................................... 14

Tools and Parts for Gas Conversion .......................................... 14

Conversion to a Local LP Gas Supply ....................................... 15

Conversion from LP Gas to Natural Gas ................................... 16

Check and Adjust the Burners ................................................... 19

OUTDOOR GRILL USE ................................................................ 20

ELECTRONIC GRILL DISPLAY ................................................... 20

Display ........................................................................................ 20

Start/Reset ................................................................................. 20

Mode .......................................................................................... 20

Using Your Outdoor Grill ............................................................ 22

Using Your Infrared Sear Burner ................................................ 23

Using Your Side Burner ............................................................. 23

Using Your Rotisserie ................................................................. 24

Rotisserie Cooking Tips ............................................................. 26

Using Your Smoker Box ............................................................ 27

Hood Lights ................................................................................ 27

USING YOUR WARMING DRAWER ........................................... 27

Control Knob .............................................................................. 27

Moist-Dry Slide Control .............................................................. 28

Setting the Controls ................................................................... 28

Warming Cookware ................................................................... 29

Warming Pans and Positioning Rack ........................................ 29

Proofing Bread ........................................................................... 29

Slow Cook Function ................................................................... 29

TIPS FOR OUTDOOR GRILLING ................................................ 30

Cooking Methods ....................................................................... 30

Grilling Chart ............................................................................... 31

OUTDOOR GRILL CARE ............................................................. 33

Replacing the Batteries .............................................................. 33

General Cleaning ........................................................................ 34

Drawer Slides ............................................................................. 36

Drawer Removal......................................................................... 36

Cabinet Door Alignment - Style 2 (internal hinge) Only ............. 37

Cabinet Door Removal ............................................................... 37

TROUBLESHOOTING .................................................................. 38

ASSISTANCE OR SERVICE ......................................................... 39

In the U.S.A................................................................................ 39

Accessories ................................................................................ 39

In Canada ................................................................................... 39

WAR RANTY .................................................................................. 40

SI_CURITI_ DU GRIL D'EXTI_RIEUR ........................................... 41

EXIGENCES D'INSTALLATION ................................................... 43

Outillage et pieces ...................................................................... 43

Exigences d'emplacement ......................................................... 43

Dimensions du produit .............................................................. 44

Specifications electriques .......................................................... 44

Specifications de I'alimentation en gaz ..................................... 45

Exigences concernant le raccordement au gaz ........................ 46

INSTRUCTIONS D'INSTALLATION ............................................. 47

Installation du gril d'exterieur autoportant ................................. 47

CONVERSIONS DE GAZ .............................................................. 52

Outillage et pieces pour la conversion ....................................... 52

Conversion au gaz propane local .............................................. 53

Conversion de gaz propane &gaz naturel ................................. 54

Contr61e et reglage des brQleurs................................................ 57

UTILISATION DU GRIL D'EXTI_RIEUR ....................................... 58

AFFICHEUR I_LECTRONIQUE DU GRIL .................................... 59

Afficheur ..................................................................................... 59

Start/Reset (demarrage/r6initialisation) ...................................... 59

Mode ........................................................................................... 59

Utilisation du gril d'exterieur ....................................................... 60

Utilisation du brQleur & infrarouge .............................................. 62

Utilisation du brQleur lateral........................................................ 62

Utilisation du tournebroche ........................................................ 63

Conseils de cuisson & I'aide du tournebroche .......................... 64

Utilisation du fumoir ................................................................... 65

Lampes du capot ....................................................................... 65

UTILISATION DU TIROIR-RI_CHAUD ......................................... 66

Bouton de commande ............................................................... 66

Curseur de reglage Moist-Dry (humide-sec) .............................. 66

Reglage des commandes .......................................................... 66

Ustensiles de rechauffage .......................................................... 67

Ustensiles de rechauffage et grille de positionnement .............. 67

Levee du pain ............................................................................. 68

Fonction de cuisson lente .......................................................... 68

CONSEILS POUR L'UTILISATION DU GRIL

D'EXTI_RIEUR .............................................................................. 68

Methodes de cuisson ................................................................. 69

Tableau de cuisson au gril ......................................................... 70

ENTRETIEN DU GRIL D'EXTI_RIEUR ......................................... 72

Changement de I'ampoule d'eclairage ...................................... 72

Remplacement des piles ............................................................ 72

Nettoyage gen6ral ...................................................................... 73

Glissieres de tiroir ....................................................................... 75

Depose du tiroir .......................................................................... 75

Alignement de la porte du placard -

Style 2 (charniere interne) uniquement ...................................... 76

Depose de la porte du placard .................................................. 76

DI_PANNAGE ................................................................................. 77

ASSISTANCE OU SERVICE ......................................................... 78

Au Canada .................................................................................. 78

Accessoires ................................................................................ 78

GARANTIE ..................................................................................... 79

INSTALLATION REQUIREMENTS

asd Pa s

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here. Tools Needed

• Tape measure •

• Small, flat-blade screwdriver •

• Flat-blade screwdriver •

• #2 and #3 Phillips screwdriver

• Level •

• Short Phillips screwdriver or a

90 ° screwdriver with a Phillips screw bit

Parts Supplied

• Gas pressure regulator/hose assembly set for 11" WCP LP

gas (attached to manifold)

• Natural gas conversion kit with convertible regulator set for 4"

WCP Natural gas (on some models)

• Natural gas conversion kit (on some models)

• Rotisserie motor mounting bracket (on some models)

• Rotisserie motor (on some models)

• Rotisserie forks (on some models)

• Rotisserie spit (on some models)

• Smoker box (on some models)

• 2 warming drawer pans (on some models)

• 1 single-prong plug/500 mAmp transformer assembly for the

rotisserie motor (on some models)

• 2 - 1.5 V "D" size alkaline batteries (on some models)

• Vinyl grill cover (on some models)

Parts Needed

• 20 Ib LP gas fuel tank - approximately 18" (45.7 cm) height

and 12" (30.5 cm) diameter

• UL outdoor-rated 120 V extension cord - size 14 gauge/3 wire

(marked 14/3 W-A), 50 foot (15.2 m) maximum length

Wrench or pliers

Pipe wrench Scissors or cutting pliers

(to remove tiedowns) Noncorrosive leak-

detection solution

Explosion Hazard

Do not store fuel tank in a garage or indoors. Do not store grill with fuel tank in a garage or indoors. Failure to follow these instructions can result in death,

explosion, or fire.

Fire Hazard

Do not use grill near combustible materials. Do not store combustible materials near grill. Doing so can result in death or fire.

Select a location that provides minimum exposure to wind and traffic paths. The location should be away from strong draft

areas. Do not obstruct flow of combustion and ventilation air.

Clearance to combustible construction for freestanding outdoor grills:

• A minimum of 24" (58 cm) must be maintained between the front of the grill hood, sides and back of the grill and any

combustible construction.

• A 24" (58 cm) minimum clearance must also be maintained below the cooking surface and any combustible construction.

Rotisserie

A 6" (15.2 cm) minimum clearance is needed for the rotisserie

motor.

A grounded, 3-prong outdoor outlet is located on the back of the

grill. See "Electrical Requirements" section. NOTE: The rotisserie is an accessory on some models. See the

"Assistance or Service" section to order.

..... :T;,

f i L t

17W'

(43.8 cm)

28Vd'

(72.4 crn)

front of

handle to

back of grimm

17W'

62%"

(158.7 crn)

50W' (127.2 cm)

A. 61 V2"(156.2 cm) on 2 7" (68.6 cm) models KFRS2 71T and KFRU2 71V

70Y2"(179.1 cm) on 36" (91.4 em) models KFRS361 T,KFRU361 V,

KFRS365T and KFRU365V 84Y2" (214.6 em) on 36" (91.4 em) models with side burner -

KFRU368T and KFRU368V 96Y2" (245.1 em) on 48" (121.9 em) models with side burner -

KFRU488T and KFRU488V

B. 27" (68.6 em)

36" (91.4 cm) 48" (121.9 cm)

C. Not available on 27" (68.6 cm) models

14" (35.6 cm) on 36" (91.4 cm) and 48" (121.9 cm) models

,,"_T..................... _,,

cm)

@ @_@@@@

To avoid electrical shock, do not immerse cord or plugs in water or other liquid.

Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts.

Do not operate any outdoor cooking gas appliance with a damaged cord, damaged plug, or after the appliance

malfunctions or has been damaged in any manner. Contact the manufacturer for repair.

Do not let the cord hang over the edge of a table or touch hot surfaces.

• Do not use an outdoor cooking appliance for purposes other than intended.

When connecting, first connect plug to the outdoor cooking gas appliance then plug appliance into the outlet.

Use only a Ground Fault Interrupter (GFI) protected circuit with this outdoor cooking gas appliance.

Do not remove the ground prong or use with an adapter of 2 prongs.

Use only extension cords with a 3 prong grounding plug rated for the power of the equipment and approved for outdoor use

with a W-A marking.

The model/serial number rating plate is located inside the grill

cabinet on the right-hand cabinet side. See the following illustration.

x.@:?I_,. :*@?__.@ ?_I't:,,,

Electrical Shock Hazard

Use only a UL listed, 14 gauge, 3 wire extension cord

approved for outdoor use, marked W=A, with a

maximum length of 50 ft. Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Failure to follow these instructions can result in death,

fire, or electrical shock.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Check with a qualified electrician if you are not sure whether the grill is properly grounded.

A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical supply is required.

It is recommended that a separate circuit servicing only this grill be provided.

A. Model/serial number plate

Recommended Ground Method

The outdoor grill, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes, with the National Electrical Code ANSI/NFPA 70, or Canadian Electrical Code, CSA C22.1.

Copies of the standards listed above may be obtained from: CSA International 8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575 National Fire Protection Association

One Batterymarch Park Quincy, Massachusetts 02269

S ............................

A.3-prong ground plug B.3-prong polarized type outdoor GFIoutlet C. Ground prong

Explosion Hazard

Use a new CSA International approved "outdoor" gas supply line.

Securely tighten all gas connections. if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include: licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Burner Requirements for High Altitude

Input ratings shown on the model/serial rating plate are for elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a rate of 4% for each 1,000 ft (304.8 m) above sea level. Orifice conversion is required. See "Assistance or Service" section to

order.

Gas Supply Line Pressure Testing

Testing above 1/2psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):

The grill and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of that system at test pressures greater than 1/2psi (3.5 kPa).

Testing below 1/2psi (3.5 kPa) or 14" (35.5 cm) WOP (gauge) or

lower:

The grill must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to

or less than 1/2psi (3.5 kPa).

20 Ib LP Gas Fuel Tank

Observe all governing codes and ordinances. IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas

Code ANSI Z223.1 - latest edition or CAN/CGA B149.1 - latest edition.

IMPORTANT: Grill must be connected to a regulated gas supply. Refer to the model/serial rating plate for information on the type

of gas that can be used. If this information does not agree with the type of gas available, check with your local gas supplier.

Gas Conversion: No attempt shall be made to convert the grill from the gas

specified on the model/serial rating plate for use with a different gas type without consulting the serving gas supplier. The conversion kit supplied with grill must be used. See "Gas

Conversions" section for instructions.

Gas Pressure Regulator

The gas pressure regulator supplied with this grill must be used. The inlet (supply) pressure to the regulator should be as follows

for proper operation:

LP Gas:

Operating pressure: 11" (27.9 cm) WCP Inlet (supply) pressure: 11" to 14" (27.9 cm to 35.5 cm) WCP

Natural Gas: Operating pressure: 4" (10.2 cm) WCP

Inlet (supply) pressure: 7" to 14" (17.8 cm to 35.5 cm) WCP maximum.

Contact local gas supplier if you are not sure about the inlet (supply) pressure.

This grill is equipped for use with a20 Ib LP gas fuel tank (fuel

tank not supplied). A gas pressure regulator/hose assembly is supplied.

It is also design-certified by CSA International for local LP gas supply or for Natural gas with appropriate conversion.

A. Gaspressure regulator/hose assembly

The 20 Ib LP gas fuel tank must be mounted and secured.

Drawer Style Tank Tray

1. Open the drawer for the 201b LP gas fuel tank.

2. Place the 20 Ib LP gas fuel tank bottom collar into the mounting hole in the tank tray.

3. Tighten the locking screw against the bottom collar of the 20 Ib LP gas fuel tank to secure.

A , _

B C

A. Locking screw

B.Mounting hole

C. Bottom coflar

4. Slide the drawer with the 201b LP gas fuel tank back into the cabinet.

DoorStyleTankTray

1. Opencabinetdoors.

2. Pressthelockingtabonthetanktrayandpulloutthetray.

Follow instructions for converting to local LP gas in the "Gas Conversions" section.

A. 20 Ib LP gas fuel tank tray locking tab

3. Place the 20 Ib LP gas fuel tank bottom collar into the mounting hole in the tank tray.

4. Tighten the locking screw against the bottom collar of the 20 Ib LP gas fuel tank to secure.

B C

A. Locking screw B. Mounting hole

C. Bottom collar

5. Slide the tank tray back into the cabinet and lock into place.

Local LP Gas Supply Conversion

Conversion must be made by a qualified gas technician. The qualified gas technician shall provide the gas supply to the selected grill location in accordance with the National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition, and local codes. For conversion to local LP,the convertible regulator in the conversion kit supplied with the grill (on some models) must be used. Models that do not come with the conversion kit require Convertible Regulator Part Number W10132702. See "Assistance or Service" section for information on ordering.

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54 - latest edition. The qualified LP gas technician shall provide the LP gas supply to the selected

grill location in accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 and local codes.

<, _> < ,

S .............................................................

A. New ANSI Z21.54 certified gray hose B. Rear of grill C. To local LP gas supply

The gas supply line shall be equipped with an approved shutoff

valve. This valve should be located in the same area as the grill and should be in a location that allows ease of opening and closing. Do not block access to the shutoff valve. The valve is for turning on or shutting off gas to the grill.

A. Gas supply line B. Shutoff valve "open" position C. To grill

Natural Gas Conversion

Conversion must be made by a qualified gas technician. The qualified Natural gas technician shall provide the Natural gas supply to the selected grill location in accordance with the National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition, and local codes. For conversion to Natural gas, the Natural Gas Conversion Kit supplied with the grill (on some models) or the

Natural Gas Conversion Kit Part Number W10118098 must be used. See "Assistance or Service" section for information on

ordering. IMPORTANT: The gas installation must conform with local

codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 - latest edition.

Follow instructions for converting to Natural gas in the "Gas Conversions" section of this manual or the instructions supplied

with Natural Gas Conversion Kit Part Number W10118098.

INSTALLATION

INSTRUCTIONS

():/ (}4}_

Excessive Weight Hazard

Use two or more people to move and install grill.

Failure to do so can result in back or other injury.

1. Unpack grill. Remove all packaging materials and remove grill from wooden skid.

2. Move grill into desired outdoor location.

3. Open the hood.

Remove Packaging Material Inside the Grill

1. Cut the tiedowns holding the grates together.

2. Remove condiment shelf, warming shelf and grill grates from inside the grill and remove packaging material.

3. Remove foam block and wrap from inside the grill.

A. New ANSI Z21.54 certified gray hose

B.Rear of grill

C. To Natural gas supply

The gas supply line shall be equipped with an approved shutoff valve. This valve should be located in the same area as the grill and should be in a location that allows ease of opening and closing. Do not block access to the shutoff valve. The valve is for turning on or shutting off gas to the grill.

A. Gas supply line B. Shutoff valve "open" position C. To grill

A ..........

.......... _ //i;::_B

,/ •

A. Foamblock

B.Foam wrap

Replace the grill grates.

Place warming shelf on brackets as shown.

A A

A. Warming shelf brackets B. Warming shelf

Attach Side Shelf (on some models)

Attach Condiment Shelf (on some models)

1. Open doors below grill and remove carton. Unpack side shelf.

2. Locate 4 screws. Install 2 screws in the top 2 holes on each side of the grill. Leave screws away from side of grill about 1_,,(0.64 cm).

Install side shelf on left side of the grill. Position the side shelf so that the large end of the keyhole slots are over the screws.

Place shelf onto the 2 mounting screws. Let the shelf slide down so the screws are in the narrow neck of the slots.

A .....................

1. Open cabinet door.

2. Use a short Phillips screwdriver or a 90 ° screwdriver with a Phillips screw bit to loosen the 2 mounting screws on the inner door panel.

A. Mounting screws

Position the condiment shelf so that the large ends of the keyhole slots are over the 2 mounting screws.

A. Top of side shelf B. Keyhole slot

C. Front of side shelf D. Side of grifl

4. Install the bottom 2 screws and tighten.

5. Tighten the top 2 screws.

Attach Cabinet Doors (on some models)

1. Remove foam wrapping from both cabinet doors.

2. Position hinge pins on the door with the hinge brackets on the cabinet. Gently push down to slide the pins into place.

A.Mounting screw inkeyholeslot

B.Condiment shelf

Lower the condiment shelf until the 2 mounting screws are in the narrow ends of the keyhole slots.

Tighten the screws.

Dispose of/recycle all packaging material.

A. Door hinge pin

B. Hinge bracket

Make Gas Connection - Toa 20 Ib LP Gas Fuel Tank

Explosion Hazard

Securely tighten all gas connections. if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water column.

Examples of a qualified person include: licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Screw the gas pressure regulator/hose assembly to the 20 Ib LP gas fuel tank as shown. (To disconnect, turn off the gas supply to the 20 Ib LP gas fuel tank, then unscrew the gas pressure regulator/hose assembly from the 20 Ib LP gas fuel tank as shown.)

If converting to local LP or Natural gas, follow instructions in the "Gas Conversions" section.

LP Gas: IMPORTANT: A 20 Ib LP gas fuel tank must be purchased

separately. IMPORTANT: The gas pressure regulator/hose assembly

supplied with the grill must be used. Replacement gas pressure regulator/hose assembly specific to your model, is available from your outdoor grill dealer.

Drawer Style Tank Tray To Install the 20 Ib LP Gas Fuel Tank:

1. Open the drawer for the 201b LP gas fuel tank.

2. Place the 20 Ib LP gas fuel tank bottom collar into the mounting hole in the tank tray

3. Tighten the locking screw against the bottom collar of the 20 Ib LP gas fuel tank to secure.

A. 20 Ib LP gas fuel tank

B. Gaspressure regulator/hose assembly

5. Turn on the gas supply. Wait a few minutes for gas to move through the gas line.

6. Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

7. Slide the drawer with the 201b LP gas fuel tank back into the cabinet.

8. The batteries are not factory installed. The 1.5-volt "D" size alkaline batteries are located in the accessory box on the grill grate. Install the batteries at this time following the instructions in the "Replacing the Batteries" section.

9. Go to "Plug in Grill" in this section.

Door Style Tank Tray

To Install the 20 Ib LP Gas Fuel Tank:

1. Open cabinet doors.

2. Press the locking tab on the tank tray and pull out the tray..

B C

A. Locking screw B. Mounting hole

C. Bottom collar

A. 20 Ib LP gas fuel tank tray locking tab

3. Place the 20 Ib LP gas fuel tank bottom collar into the mounting hole in the tank tray.

4. Tighten the locking screw against the bottom collar of the 20 Ib LP gas fuel tank to secure.

Gas Connection to Natural Gas or Local LP Gas

B C

A. Locking screw B. Mounting hole

C. Bottom collar

Screw the gas pressure regulator/hose assembly to the 20 Ib LP gas fuel tank as shown. (Todisconnect, turn off the gas supply to the 20 Ib LP gas fuel tank, then unscrew the gas pressure regulator/hose assembly from the 20 Ib LP gas fuel

tank as shown.

A. 20 Ib LP gas fuel tank

B.Gas pressure regulator/hose assembly

6. Turn on the gas supply. Wait a few minutes for gas to move through the gas line.

7. Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

8. Slide the tank tray back into the cabinet and lock into place.

9. The batteries are not factory installed. The 1.5-volt "D" size alkaline batteries are located in the accessory box on the grill grate. Install the batteries at this time following the instructions in the "Replacing the Batteries" section.

10. Go to "Plug in Grill" in this section.

Explosion Hazard

Use a new CSA International approved "outdoor"

gas supply line.

Securely tighten all gas connections. if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water column.

Examples of a quaJified person include: licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

This installation must conform with local codes and ordinances.

In the absence of local codes, installations must conform with either the National Fuel Gas Code ANSI Z223.1, or CAN/CGA- B149.1 Natural Gas and Propane installation code.

Copies of the standards listed above may be obtained from: CSA International

8501 East Pleasant Valley Rd. Cleveland, Ohio 44131-5575

National Fire Protection Association One Batterymarch Park

Quincy, Massachusetts 02269

1. Make gas connections. A combination of pipe fittings must be used to connect the

grill to the existing gas line.

• If local codes permit, use an outdoor flexible stainless

steel tubing gas connector, design-certified by CSA International, to connect the grill to the rigid gas supply line. A 5/8"diameter line is recommended. Using a wrench to tighten, connect the gas supply to the grill. Use pipe- joint compound on all non-flared male threads. Do not

kink or damage the flexible connector when moving the

grill.

• Pipe-joint compounds suitable for use with LP gas must be used. Do not use TEFLON ®ttape. Plug in Grill

C ........ !! .......................

A. New ANSI Z21.54 certified gray hose B. Rear of grill

C. To Natural gas supply

Open the manual shutoff valve in the gas supply line. The valve is open when the handle is parallel to the gas pipe.

A. Closed valve B. Open valve

3. Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

4. The batteries are not factory installed. The 1.5-volt "D" size alkaline batteries are located in the accessory box on the grill grate. Install the batteries at this time following the instructions in the "Replacing the Batteries" section.

5. Go to "Plug in Grill" in this section.

Electrical Shock Hazard

Use only a UL listed, 14 gauge, 3 wire extension cord

approved for outdoor use, marked W=A, with a

maximum length of 50 ft. Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter. Failure to follow these instructions can result in death,

fire, or electrical shock.

Plug a UL outdoor rated 14 gauge/3 wire extension cord (marked W-A) (maximum length 50 foot [15.2 m]) into the male receptacle on the back of the grill.

A. UL outdoor rated 14 gauge/3 wire extension cord

B.Male receptacle

C. Circuit breaker button

2. Plug extension cord into grounded 3-prong GFI outlet.

t®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

S ...............................

A .... ".....................

A. 3-prong ground plug B. 3-prong polarized type outdoor GFI outlet

C. Ground prong

To avoid electrical shock, do not immerse cord or plugs in water or other liquid.

Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts.

Do not operate any outdoor cooking gas appliance with a damaged cord, damaged plug, or after the appliance malfunctions or has been damaged in any manner. Contact the manufacturer for repair.

Do not let the cord hang over the edge of a table or touch hot surfaces.

Do not use an outdoor cooking appliance for purposes other than intended.

When connecting, first connect plug to the outdoor cooking gas appliance then plug appliance into the outlet.

Use only a Ground Fault Interrupter (GFI) protected circuit with this outdoor cooking gas appliance.

Do not remove the ground prong or use with an adapter of 2 prongs.

Use only extension cords with a 3 prong grounding plug rated for the power of the equipment and approved for outdoor use with a W-A marking.

NOTE: Check the circuit breaker on the back of the grill after plugging the grill into a 3-prong polarized type outdoor GFI outlet if there is a loss of electrical power to the grill. Reset the circuit breaker if the button is in the tripped position. Push

in the rubber boot and button to reset.

A. Rubber boot

B. Circuit breaker button in

"set" position

3. Go to "Check and Adjust the Burners" section

A. Rubber boot

B. Circuit breaker button

in "tripped" position

GAS CONVERSIONS

NOTE: These instructions are for grill models that come equipped with the conversion kit for Local LP and Natural gas. For models that do not come equipped with the conversion kit: for conversion to Local LP order Regulator Part Number W10132702, or for conversion to Natural gas order LP to Natural Gas Conversion Kit Part Number W10118098. Use the conversion instructions included in the kit. See "Assistance or Service" section for information on ordering.

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

Tools needed

• Phillips screwdriver

• Pipe wrench

• Adjustable wrench

• 10 mm wrench

• 6 mm socket and wrench or 6 mm nut driver

• 10 mm socket and wrench or 10 mm nut driver

• Thin flat-blade screwdriver

• Pliers

• Pipe thread sealant certified for LP gas

Parts supplied

• Brass connector

• Convertible regulator 4" W.C. Natural, 11" W.C. LP

• Natural gas orifices IMPORTANT: Gas conversions must be done by a qualified

installer. Before proceeding with conversion, shut off the gas supply to the appliance prior to disconnecting the electrical power.

This kit is designed for use from sea level up to 2000 ft elevation. For higher elevations contact KitchenAid at 1-800-422-1230 in

the U.S.A. or call 1-800-607-6777 in Canada.

Explosion Hazard

Use a new CSA international approved "outdoor"

gas supply line. Securely tighten all gas connections.

ifconnected to LP, have a qualified person make sure gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include: licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

I01 .,)CI I,I _ "'<,"__ _"_ .....

Installation of the regulator

1. Turn off the main gas supply valve.

2. Unplug grill or disconnect power.

3. Disconnect 20 Ib LP gas fuel tank (if present).

4. Turn off all burner control valves.

5. Remove rear cover and 2 screws.

Use adjustable wrench to remove LP hose regulator from brass elbow. Use adjustable wrench to remove brass elbow

from shutoff valve.

9. Use pipe wrench to install the convertible regulator. Brass cap will be facing up when tight.

A B

iii _,iiiiiio

A, Brass connector B. Convertible regulator

10. To set the appliance regulator for LP gas, use adjustable wrench to remove the brass cap on the convertible regulator.

11. Examine the stem on the brass cap. The letters "NAT" should be showing on the end of the plastic stem farthest away from the brass cap.

12. Remove stem from cap, turn it over and snap stem back into the cap so the letters "LP" are at the end of the stem farthest away from the brass cap.

A. Manifold

B.Brass elbow

C. Rear of grill D. Gas pressure regulator/hose assembly

Apply pipe sealant to the threads of the brass connector. Use pipe thread sealant that is certified for use with LP gas.

Use adjustable wrench to install brass connector (supplied) to shutoff valve.

NOTE: The arrow on the regulator must be pointing toward the brass connector.

13. Use adjustable wrench to reinstallcap onto regulator.

Make Grill Connections

Connect Local LP Gas Supply

1. Use pipe wrench to connect certified 1/2"(1.3 cm) gas supply pipe to inlet side of regulator from Fixed LP gas supply according to local codes requirements. Use pipe thread sealant that is certified for use with LP gas at connections where required. There must be a certified manual shutoff valve in the gas supply line near the grill for easy access.

2. Turn on the gas supply to the grill.

3. Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leaks found.

Record Conversion

In the last page of the Use and Care Guide, write "Converted to Local LP Gas Supply." Also record the conversion date and the technician/company that performed the conversion.

Installation of the regulator

1. Turn off the main gas supply valve.

2. Unplug grill or disconnect power.

3. Disconnect 20 Ib LP gas fuel tank (if present).

4. Turn off all burner control valves.

5. Remove rear cover and 2 screws.

Use adjustable wrench to remove LP hose regulator from brass elbow. Use adjustable wrench to remove brass elbow

from shutoff valve.

9. Use pipe wrench to install the convertible regulator. Brass cap will be facing up when tight.

A B

iii _'iiiiiio

A. Brass elbow B. Convertible regulator

10. To make sure the regulator is set for Natural gas, use adjustable wrench to remove brass cap on appliance regulator.

11. Examine the stem on the brass cap. If the letters "NAT" are not showing on the end of the plastic stem farthest away from the brass cap, remove stem from cap, turn it over and snap stem back into the cap so the letters "NAT" are at the end of the stem farthest away from the brass cap.

A. Manifold

B.Brass elbow

C. Rear of grill D. Gas pressure regulator/hose assembly

Apply pipe sealant to the threads of the brass connector. Use pipe thread sealant that is certified for use with LP gas.

Use adjustable wrench to install brass connector (supplied) to shutoff valve.

NOTE: The arrow on the regulator must be pointing toward the brass connector.

12. Reinstall cap onto convertible regulator.

Change the main grill burner valve orifices

1. Manually remove all of the grates, sear plate, and burners.

2. Remove the 2 screws that hold the burner in place. Remove gas burner from the grill.

A. Two screws

3= Use 6 mm socket and wrench or 6 mm nut driver to remove

the brass orifices from the end of the gas valves.

A. Grill burner orifice

Install new 2.34 mm orifices supplied with this kit to the end of the gas valve. Use 6 mm socket and wrench or 6 mm nut driver to tighten.

NOTE: The number 2.34 is stamped on the orifice for identification.

Change the Rotisserie-infrared burner orifice(s)

1. Remove the access cover and screw at the back of the grill hood with a Phillips screwdriver.

Use Phillips screwdriver to remove 2 screws holding the spider guard to the burner.

B,(

A. Spider guard B. Two screws

Use 10 mm wrench to remove the brass orifice located at the end of the supply pipe.

A. Grill burner orifice

Replace burner by sliding the middle tube (venturi) over the orifice.

A.Burner/orifice connection B.Burner

Reattach gas burner using 2 screws.

For models with 1 rotisserie burner:

Install 1.9 mm orifice supplied with this kit to the end of the supply pipe. Use 10 mm wrench to tighten.

For models with 2 rotisserie burners:

Install 1.55 mm orifice supplied with the kit to the end of the supply pipe. Use 10 mm wrench to tighten.

NOTE: The number 1.9 mm or 1.55 mm is stamped on the orifice for identification.

5. Replace the spider guard and secure with the 2 screws removed in Step 2.

6. Repeat the procedure for each rear burner.

Change the Side burner orifices (for models equipped with side burner)

1. Remove the side burner grates.

2. Remove the burner caps. The caps are interlocked to the burner base. Twist and lift the burner caps to remove.

3. Use 10 mm socket and wrench or 10 mm nut driver to remove the brass orifices from inside the burner base.

A. Two screws

Repeat the procedure for each grill burner.

Use 10 mm socket and wrench or 10 mm nut driver to install the new 2.1 mm orifices supplied with this kit.

NOTE: The number 2.1 is stamped on the orifice for identification.

Repeat the procedure for the other burner.

Replace the burner top and caps. Align the notches in the bottom of the burner top with the tabs on the burner base and twist until the burner top is seated on the burner base. You will feel it drop into the deep notch.

A B

A.Burner top notches B. Burnerbase tabs

4. Remove the sear burner mounting screws.

A. Sear burner mounting screws

Lift the sear burner out of the grill.

Use 6 mm socket wrench or 6 mm nut driver to remove the orifice. Install the new 2.34 mm orifice supplied.

NOTE: The number 2.34 is stamped on the orifice for identification.

7. Replace the side burner grates.

Change the Sear burner orifices (for models equipped with sear burner)

1. Remove the sear burner cover screws. Set the screws and cover aside.

A. Sear burner cover screws

Remove the burner igniter mounting screws.

Loosen the sear burner plate, located next to the igniter.

A. Burner igniter mounting screws

7. Reinstall sear burner. Make sure that the igniter is out of the way to allow proper positioning of burner. Use Phillips screwdriver to attach the mounting screws.

8. Use Phillips screwdriver to reattach the igniter and sear burner plate.

9. Reinstall sear burner cover. Use Phillips screwdriver to attach mounting screws.

Hook up to Natural gas and Leak Test

1. Use pipe wrench to connect certified 1/2"(1.3 cm) gas supply pipe to inlet side of regulator from Natural gas supply according to local codes requirements. Use pipe thread sealant that is certified for use with LP gas at connections where required. There must be a certified manual shutoff valve in the gas supply line near the grill for easy access.

2. Turn on the gas supply to the grill.

3. Test all connections using an approved noncorrosive leak- detection solution. Bubbles will show a leak. Correct any leak

found.

Record Conversion

1. The appliance nameplate is located inside the grill cabinet on the right-hand cabinet side. With a permanent marker, check the box next to "Natural gas" and mark through "LP - Propane."

In the last page of the Use and Care Guide, write "Converted to Natural Gas." Also record the conversion date and the

technician/company that performed the conversion. NOTE: Place LP gas parts in plastic parts bag for future use and

keep with pack containing literature.

The burners are tested and factory-set for most efficient 5. operation. However, variations in gas supply and other conditions may make minor adjustments to air shutter or low flame setting necessary.

It is recommended that a qualified person make burner adjustments.

NOTE: The rotisserie burner cannot be adjusted. Checking and adjusting the grill burner flames requires removing

the grate and sear plates.

Burner Flame Characteristics

The flames of the grill burners and side burners (on some models) should be blue and stable with no excessive noise or lifting (LP gas flames will have a slightly yellow tip). A yellow flame indicates not enough air. If flame is noisy or lifts away from the burner, there is too much air. Some yellow tips on flames when the burner is set to HI setting are acceptable as long as no carbon or soot deposits appear.

Main burner

(1.9 - 2.5 crn) on all burner ports

with burners on

"Hi" setting

A. Burner ports

Side burner

Remove the 2 screws that hold the burner in place. Remove gas burner from the grill.

A.2 screws

If flame is yellow (not enough air), turn air shutter adjustment screw counterclockwise.

If flame is noisy or lifts away from burner (too much air), turn air shutter adjustment screw clockwise.

A.Air shutteradjustment screw

Adjustment should be made clockwise or counterclockwise from V8" (3.2 mm) to V4"(6.4 mm).

Replace gas burner, sear plates and grates.

Light grill using information in the "Outdoor Grill Use" section. See "Burner Flame Characteristics."

(1.9-2.5cm)

on aH burner ports with burners on

setting

Check that burners are not blocked by dirt, debris, insect nests, etc. and clean as necessary. If they are clean, adjust air shutters

as needed. IMPORTANT: Before adjusting air shutters, let burners cool

completely. To Adjust:

1. Light grill using information in the "Outdoor Grill Use" section.

2. Observe flame to determine which burners need adjustment and how the flame is acting.

3. Turn off the valve and wait until grill and burners cool completely.

4. Remove grill grates and sear plates.

Low Flame Adjustment

If flame goes out on the "LO" setting, the low flame setting must be adjusted.

1. Turn off the valve and wait until grill and burners are cool.

2. Remove grill grates and sear plates.

3. Light grill using information in the "Outdoor Grill Use" section.

4. Turn burner to its lowest setting and remove knob.

5. Hold valve stem with pliers and insert a small flat-blade screwdriver into the shaft.

6. Watch the flame and slowly turn the screwdriver counterclockwise.

7. Adjust flame to minimum stable flame.

A. Valve stem B. Small flat-blade screwdriver C. Pliers

8. Replace the control knob and turn off the burner.

9. Repeat steps 3 through 8 for each burner if needed.

10. Replace the sear plates and grates after the burners have cooled.

OUTDOOR GRILL USE

This manual covers several different models. The grill you have purchased may have some or all of the features listed. The locations and appearances of the features shown here may not match those of your model.

Control Panel

A B C D E F G H /

ROTISSERIE LEFT CENTER RIGHT SEAR ROTISSERIE FRONT REAR

BURNER BURNER BURNER BURNER BURNER BURNER BURNER BURNER

A. Left rotisserie burner control knob

B. Left grill burner control knob

C. Center grifl burner control knob

D. Right grill burner control knob E. Electronic grill display (on some models)

Light switch button (on some models)

F Sear burner control knob

ELECTRONIC GRILL DISPLAY

A B

O Fuel Remaining O Timer

O Flame Time

Time Set Start/Reset

A. Timer display B. Mode indicator fights

C. Mode selection button

The display will turn on when a gas burner is lit. The display will default to Fuel Remaining.

This display will also turn on when the Mode, Timer or Start/ Reset button is pushed. The information displayed will be for the mode of the lit indicator light.

The display area will go blank 10 minutes after the last time that a button was pushed (except the light button).

If the display does not turn on or if "NP" or "El" is displayed, see "Troubleshooting" section.

D E F

D. Time set button

E. Start/reset button F Hood light on/off button

G. Right rotisserie burner control knob

H. Front side burner control knob

I. Rear side burner control knob

The Start/Reset button starts the Timer and Flame Time TM cycle. This button also stops and resets these features.

The mode button selects features on the display control.

When the grill is not lit and the Mode button is pushed, it will only display the information for Modes 1 and 2. The grill must be lit for

Mode 3 to be activated.

Mode I - Fuel Remaining Feature

The fuel remaining feature displays a calculated amount of time

(hours and minutes) the grill can remain lit at the current gas usage rate before the 201b LP gas fuel tank runs out of fuel.

The Fuel Remaining can be checked when the grill is OFE

check fuel remaining with the grill OFF:

Press Mode button until the indicator light for "Fuel Remaining" comes on. "00:00" will appear in the display. After 10 seconds a calculated Fuel Time Remaining will appear in the display.

To check fuel remaining with the grill burners ON:

1. Press Mode button until the indicator light for "Fuel Remaining" comes on. "00:00" will appear in the display. After 10 seconds a calculated Fuel Time Remaining will appear in the display.

2. The fuel time remaining will be recalculated automatically 7-10 minutes after the grill has been lit.

NOTE: This recalculated display of fuel time remaining may increase when the grill is used on medium or low settings because the gas consumption is less.

When the 20 Ib LP gas fuel tank is Low:

1. The "Fuel Remaining" indicator light will flash when the gas weight is less than 2.64 Ibs (1.2 kg).

2. When gas weight is less than 1.76 Ibs (0.8 kg) the display for Fuel Remaining will show 00:00 and a tone will sound 2 times every 20 seconds for five minutes. The fuel shutoff valve will not close, unless the Flame Time TM mode is selected.

Mode 2 - Timer

The Timer can be set in hours and minutes up to 12 hours and 59 minutes, then counts down the set time.

To Set:

1. Press the Mode button until the timer indicator light comes

on.

2. Press the Time Set Button to increase the time by 1 minute or press and hold the Time Set button to increase the time rapidly.

3. When desired time is set, press the Start/Reset button once to start the timer countdown. When the set time ends,

reminder tones will sound.

4. Press Start/Reset button to reset the Timer or cancel the reminder tones.

NOTE: The minute timer will continue counting down until the set time ends or the Start/Reset button is pushed to cancel

the timer.

Mode 3 - Flame Time TM Feature

The Flame Time TM feature automatically shuts off gas to the burners 10 minutes after set time has expired. This feature can

be set for 1 to 60 minutes. Flame Time TM can be used to keep grill burning for a set amount

of time for grilling or for burn off of the grill grates.

For burn off of grill grates

With the lid closed and the main burners on HI, residue will burn off the main grill grates. After the grill shuts off and is cool, the

grates can be scraped off more easily. The recommended time for burn off is 45 minutes.

To set Flame Time TM mode for burn-off:

1. Light all main burners and set them on HI and close the hood.

2. Press the "Mode" button until the indicator light for Flame Time TM comes on.

3. Press the "Time Set" button to the amount of time you want the grill to be on. The recommended time for burn off is

45 minutes.

4. Press "Start/Reset" button to start the Flame Time TM feature timer countdown. When the set time ends (00:00), the

reminder tone will sound.

• If the Start/Reset button is pushed within 10 minutes after

the Flame Time TM timer reaches 00:00 the fuel shutoff valve will not close automatically. The Flame Time TM timer

can be reset and continue the burn-off or timed grill and the timer will count down the new set time.

If the Start/Reset button is not pushed within 10 minutes after Flame Time TM timer reaches 00:00 the fuel shutoff

valve will close automatically and the display for the Flame Time TM feature will be off. If the mode button is

pushed, "El" will be appear in the display if there is at least one valve still turned on. The tone will sound one

time. If Mode button is pushed a second time the Fuel time remaining will be displayed.

If the valves are shut off while the Flame Time TM mode timer is counting down, it will stop counting and keep the

data. If the start/reset button is pushed when the valves are turned on again, the Flame Time TM timer will continue

to count from the last stored data.

Press Start/Reset button to cancel this feature or the reminder tones.

NOTE: All of the burner valves must be turned to the off position before grill can be lit after a Flame Time TM cycle has

been used.

When the LP tank is Low:

1. The "Fuel Remaining" indicator light will flash when the gas weight is less than 2.64 Ibs (1.2 kg).

2. When gas weight is less than 1.76 Ibs (0.8 kg) the fuel shutoff valve will close instantly and "El" will appear in the display. The indicator light for Flame Time TM mode will be lit.

3. If the gas weight is less than 1.76 Ibs (0.8 kg) the Flame Time TM mode will not activate if selected.

For Timed Grill "ON" Toset the amount of time for grilling, follow the steps the same as

burn-off of grill grates except you need to light only the burners you wish to use and adjust the burner knob to desired grill

setting. The hood can be up or down depending on your grilling preference.

Lights

1. Press the lights button to turn the lights inside the grill hood "On" or "Off."

NOTE: The power supply must be plugged in for lights to work. If lights do not work, see "Outdoor Grill Care" section for changing the light bulbs.

Explosion Hazard

Do not store fuel tank in a garage or indoors. Do not store grill with fuel tank in a garage or indoors. Failure to follow these instructions can result in death,

explosion, or fire.

Fire Hazard

Contact the dealer and use only replacement hoses specified for use with the grill.

A. Gas pressure regulator/hose assembly

Check the Drip Tray Pans

Open the drip tray and check the drip pans for grease and other liquids. Clean the drip tray and pans often to avoid grease and other liquid buildup.

Water can build up in the drip tray and pans if the grill is not covered when not in use.

See Drip Tray in the "General Cleaning" section for emptying and cleaning the drip tray and pans.

The drip tray must be in place and pushed all of the way in when

using the grill.

Do not use grill near combustible materials. Do not store combustible materials near grill. Doing so can result in death or fire.

Food Poisoning Hazard

Do not let food sit for more than one hour before or

after cooking.

Doing so can result in food poisoning or sickness.

Inspect the 20 Ib LP Gas Fuel Tank Supply Hose

Inspect the gas pressure regulator/hose assembly before each use.

1. Open the right-hand drawer and slide 20 Ib LP gas fuel tank out.

2. Inspect the entire gas pressure regulator/hose assembly for cuts, abrasions, or excessive wear.

3. If necessary, replace the gas pressure regulator/hose assembly before using the grill.

Prepare the Gas Supply

1. Open the hood completely. Do not light burners with the hood closed.

2. Make sure the control knobs are all turned to the OFF position.

Turn the Gas Supply On

1. For freestanding outdoor grills using a 20 Ib LP gas fuel tank: Slowly open the 20 Ib LP gas fuel tank valve.

NOTE: If flow limiting device activates, your grill may not light. If your grill does light, the flames will be low and will not

heat properly. Turn 20 Ib LP gas fuel tank valve and all control knobs off and wait 30 seconds. After shutting off the 20 Ib LP

gas fuel tank, very slowly open tank valve and wait 5 seconds before lighting.

2. For outdoor grills using gas supply source other than 20 Ib LP gas fuel tank:

Open the manual shutoff valve in the gas supply line. The valve is open when the handle is parallel to the gas pipe.

Lighting the Grill and Infrared Sear Burner

1. Do not lean over the grill.

2. Select the burner you want to light. Push in and turn the grill burner control knob to LITE/HI, while continuing to hold it in.

3. You will see the igniter glow or hear the "snapping" sound of the spark (depending on your model). When burner is lit,

release the knob. Turn knob to desired setting.

4. Repeat for each of the other burners as needed.

IMPORTANT: If burner does not light immediately, turn the burner knob to OFF and wait 5 minutes before relighting.

Manually Lighting Main Grill and Infrared Sear Burners

1. Do not lean over the grill.

2. Remove the manual lighting extension (see following illustration) and attach a match to the split ring.

Infrared grilling produces intense heat which quickly sears the meat. Searing locks in flavor and juices while allowing the outer surface to absorb smoke and food aroma that is produced as grease and drippings are vaporized by the burner. The result is a crisp, flavorful outside with a tender, juicy inside.

• Preheat the infrared sear burner for 5 minutes.

• Ensure that meats are fully thawed and that all excess fat is trimmed away prior to grilling.

• Leave the burner set to HI when placing food on the grill to sear.

• Use the sear burner to sear meat 1 to 2 minutes on each side, then move the meat to the main grill cooking surface to finish

grilling to the desired doneness.

Freestanding grills - right- hand cabinet draweror door

3. Strike the match to light it.

4. Guide the lit match between the grill grate and one of the slots in the sear plate.

5. Push in and turn the burner knob to LITE/HI for the burner closest to the lit match. The burner will light immediately.

When burner is lit, turn knob to desired setting.

6. Repeat steps 3 through 5 for each main burner.

7. Remove match and replace manual lighting extension inside the cabinet drawer or door.

IMPORTANT:

If burner does not light immediately, turn the burner knob to OFF and wait 5 minutes before relighting.

If any burners do not light after attempting to light them manually, contact the KitchenAid Customer eXperience Center. See the

"Assistance or Service" section.

NOTE: View is shown with grates removed. Grates are

to be in place when using the infrared sear burner.

Burn Hazard

Do not let the burner flame extend beyond the edge of

the pan.

Doing so can result in burns.

Lighting the Side Burner

1. Remove the side burner cover. Do not light burners with the cover on.

2. Do not lean over the grill.

3. Push in and turn the control knob to LITE/HI and hold in.

4. You will see the igniter glow or hear the "snapping" sound of the spark (depending on your model). When burner is lit, release the knob. Turn knob to desired setting.

5. Repeat for the other burner as needed.

IMPORTANT: If burner does not light immediately, turn the burner knob to OFF and wait 5 minutes before relighting.

Manually lighting the side burner

Do not lean over the grill.

Remove the manual lighting extension (see following illustration) and attach a match to the split ring.

Freestanding grills - right- hand cabinet draweror door

3. Strike the match to light it.

4. Guide the match to the burner you wish to light.

x, ......

A. Rotisserie motor B. Spit rod

C. Rotisserie fork D. Rotisserie burner

For best cooking results, do not use main grill burners when using the rotisserie.

The rotisserie system is designed to cook food from the rear

using intense, searing infrared heat. NOTE: To avoid product damage when not using the rotisserie,

remove the motor and 500 mAmp transformer assembly and store indoors. Remove the spit rod and forks. Store out of the

reach of children.

5. Push in and turn the burner knob to LITE/HI for the burner closest to the lit match. The burner will light immediately.

When burner is lit, turn knob to desired setting.

6. Repeat steps 3 through 5 for each burner.

7. Remove match and replace manual lighting extension inside the cabinet drawer or door.

IMPORTANT: If burner does not light immediately, turn the burner knob to OFF

and wait 5 minutes before relighting. If any burners do not light after attempting to light them manually,

contact the KitchenAid Customer eXperience Center. See the "Assistance or Service" section.

To Use:

1. Remove warming shelf,

2. Mount rotisserie motor on the grill's mounting bracket, Position it securely into support bracket slots, Plug single-

prong plug of the 500 mAmp transformer assembly into rotisserie motor,

A. Rotisserie motor

B. Single-prong power cord

3. To load the spit rod, slide one of the rotisserie forks onto the spit rod with prongs facing inward.

4. Push spit rod through the center of the food, then slide second rotisserie fork into position.

5. Center the food and rotisserie forks on spit rod and tighten wing nuts on the rotisserie forks. If necessary, secure loose food portions with butcher's string only.

+ 56 hidden pages