KitchenAid KFBP102LSS0 Installation Guide

II " I ctionsand 1 4008A

OutdoorBarCart

(PortableandBuilt-in)

IMPORTANT:

Readandsavethese
instructions.

IMPORTANT:
Installer: Leave Installation
Instructions with the consumer.

Comsumer: Keep Installation
Instructions for future reference.

Portable Model
KFBPIO2LSS

KJtchen_kid _

FOR THE WAY IT'S MADE _

Write down the model and serial numbers
before installing or using Outdoor Bar

Cart.
Both numbers are on the model/serial

number plate, located on the underside,
right front of the Outdoor Bar Cart.

Model #
Serial #

Built-in Model
KFBP100LSS

Questions regarding features,
operation, performance, parts or

service? Call 1-800-422-1230 or visit
our web site at www.kitchenaid.com.

Part No. 8184968 Rev. A

Beforeyoustart,,,

Product mensions

Your safety and the safety of

others are very important.

We have provided many important
safety messages in this manual and

on your appliance. Always read and
obey all safety messages.

This is the safety alert

symbol.

This symbol alerts you to

potential hazards that can kill or hurt
you and others.

All safety messages will follow the
safety alert symbol and either the

word "DANGER" or "WARNING."
These words mean:

You can be killed or seriously
injured if you don't immediately

follow instructions.

You can be killed or seriously
injured if you don't follow

instructions.

All safety messages will tell you
what the potential hazard is, tell you
how to reduce the chance of injury,
and tell you what can happen if the

instructions are not followed.

iMPORTANT: Observe all governing
codes and ordinances.

Portable and Built-in models

The portable model must
have suitable drain systems

in accordance with local
codes for the ice bin and
sink drains,

25-1/2"

30"

(76"2 crn) ------1_30 !2"

36"

(91.4 cm)

1/2"

10-1/2"

(26.7 cm)

23"

cm)

25-1/2"

cm)

-in Installation

mensions

Provide suitable drain
systems in accordance with

local codes for ice bin and
sink drains. The drains and

filter must be accessible.

10-5/8"

(27.0cm)

35-1/2"

(90.2 cm)

asic Parts

of the

ui :-in and

Portable

models

Side shelves not shown

Tools needed:

Gather the required tools and parts before
starting installation. Read and follow the
instructions provided with any tools listed.

• Level

• Phillips screwdriver

• tape measure or ruler

• slip joint pliers

• pipe wrench

• adjustable wrench

Partsneeded:

• 1-1/2" drain system

• 1" drain system

• NSF- or UPC-listed water connection lines

• plumbers putty

• clear silicon

outlet hose and

connectors sink

__ethnO_oar_ d

water filter connection

and filter

bottlewell

faucet
single

holder

drainfitting

1-1/2"

bottle well two piece

bottle

opener

bottle cap
catch pan

towelholder

sliding cover

support

bottle

rail

Installation-

Built-in model

Excessive Weight Hazard

Use two or more people to move
and install bar cart.

Failure to do so can result in back
or other injury.

Use a certified plumber to connect and
install potable water supply and drain
system to outdoor bar cart per local code
requirements,

[] Set the Bar Cart on a protective

surface such as cardboard or a blanket.

[] Make sure you have the drain

connections, in accordance with local
codes, under the Bar Cart.

[] Remove the bottle rail, bottle cap

catch pan and water filter from the ice bin.

_ Remove the faucet from the sink.

sink

washer_

Iocknut

[] Install the faucet and fasten

securely.

_ Install the water filter on the

sink/faucet side of the cutout, Position the

filter so that the plastic hose attached to

the filter easily reaches the faucet
connection.

plastichose nut

connector \ | inlet

[] Install water inlet connection in a
convenient location under the cutout.
Position the water inlet connection so that

the plastic hose easily reaches the filter
inlet connection.

plumbers putty

[] Place a small amount of plumbers
putty around both the ice bin and sink
drain mounting seats.

connector

__ mounthlg

panel

drain

plastic

hose

inlet

connector

[] Remove the bottle rail, bottle cap
catch pan and water filter from the ice bin.

[] Installthe1"(2.5cm)drainfitting
intheicebinandthe1-1/2"(3.8cm)
drainfittinginthesink.Tightensecurely.
Removeanddiscardtheexcessplumbers

putty.

[] Icebindrainandsinkdrain

fittingstobeconnectedtodrainsystemin

accordancewithlocalcoderequirements.

_y clear

silicone

filter

t4. Attach the plastic cold water

hose from the water inlet connection to
the inlet side of the filter, Use N.S.F, or
U.RC.-listed water connection line for

water supply to inlet connector, Potable
water supply system to be connected to

inlet connector per local code
requirements,

5 [] Unwrap the bottle rail and

bottle cap catch pan. Position them over
the key-lock studs and slide down to lock
in place.

6 [] Unwrap the sliding cover and

place into frame on top of the ice bin.

_ Remove the faucet from the sink.

sink

washer _

Iocknut

_ Install the faucet and fasten

securely.

plumbersputty

[] Place a small amount of plumbers

putty around both the ice bin and sink
drain mounting seats,

t [] Applyabeadofallweather
clearsiliconeontheundersideofthe
backandtwosidesofthetoplip.

[]CarefullypositiontheBarCart

intothecutout.Immediatelyremoveany
excesssilicone.

plastic

hose

filter

3 [] Connect the plastic hose from
the water filter to the faucet connection
and tighten securely.

Installation -

Portablemodel

Excessive Weight Hazard

Use two or more people to move
and install bar cart.

Failure to do so can result in back
or other injury.

Use a certified plumber to connect and
install potable water supply and drain

system to outdoor bar cart per local code
requirements,

[] Make sure you have adequate

drain connections for the Bar Cart.

drain

"____c _JaLsther

_ Ice bin drain and sink drain fittings

to be connected to drain system in
accordance with local code requirements.

[] Install the 1" (2.5 cm) drain fitting

in the ice bin and the 1-1/2" (3.8 cm)
drain fitting in the sink. Tighten securely.
Remove and discard the excess plumbers

putty.

_)_Plastic

filter

UU_____line

[] Connecttheplasticlinefromthe

waterfiltertothefaucetconnectionand

tightensecurely.

plastichose nut inlet

panel

[] Installwaterinletconnection

throughholeprovidedincabinetrear
panel.

plastic

hose

inlet

connector

filter

[] Attach the plastic cold water

hose from the water inlet connection to
the inlet side of the filter. Use N.S.F.
U.RC.-listed water connection line for

water supply to inlet connector. Potable
water supply system to be connected to

inlet connector per local code
requirements.

I [] Unwrap the bottle rail and

bottle cap catch pan. Position them over
the key-lock studs and slide down to lock
in place.

2 [] Unwrap the sliding cover and

place into frame on top of the ice bin.

3 [] Rotate the side shelves up into

their locked position or leave down as
needed.

t4 [] Lock the front locking caster

wheels when in use.

Takingcare of your
BarCart

Wipe up any water spills on the exterior.
Water can cause spots.

Stainless steel surfaces: Use any cleaner
acceptable for use on stainless steel.

Always rub in the direction of the

manufacturer's polishing marks.
Other surfaces: Clean with warm

dishwashing soap and water.

Cleaning

General Tips
IMPORTANT: Always follow label

instructions on cleaning products.

For routine cleaning, wash with soap and
water using a soft cloth or sponge. Rinse
with clean water and dry at once with a

soft, lint-free cloth to avoid spots and

streaks.

Never use steel wool, as it will scratch the

surface.

Use of the accessory cover designed for

Outdoor Bar Cart will protect finish from
weather.

Stainless Steel

IMPORTANT: Do not use soap-filled

scouring pads, abrasive cleaners,

Cooktop Polishing Creme, steel wool,

gritty wash cloths or paper towels.

Cleaners should not contain chlorine.

Damage may occur.

Rub in direction of grain to avoid

scratching or damaging the surface.

Food spills should be cleaned as soon as

possible. Spills may cause permanent

discoloration.

• Use Stainless Steel Cleaner & Polish
(Part #4396095). See "Requesting

Assistance or Service" on Page 7 to
order.

• Use a mild liquid detergent or all-
purpose cleaner according to label

instructions.

• Rinse with clean water and dry at once
with soft, lint-free cloth to avoid spots

and streaks.

• Use vinegar to remove hard water
spots. Rinse with water and dry
thoroughly.

• Use a glass cleaner to remove
fingerprints.

Exterior
The quality of this material resists most

stains and pitting, providing that the
surface is kept clean and protected.

• Apply stainless steel polish to all areas
before first use. Re-apply after each
cleaning to prevent permanent damage

to surface.

• Cleaning should always be followed by
rinsing with clean warm water.

• Use a metal polish or stainless steel
brightener to remove fingerprints, water
spots, oxidation and food stains. Always

follow the manufacturer's directions.

• Wipe the surface completely dry with a
soft cloth.

Winterization of faucet and
drain system

When temperatures are below 35 ° F for
an extended period of time:

I [] Turn off water source to sink.

_ Remove potable water supply

system from connection and
store appropriately.

_ Remove filter

from its connection and

store inside in a warm
dry area.

_ Disconnect drain

traps and 1/4" tubing

from the filter connector

and allow to drain.

_ Cover bar cart with accessory

cover or tarp.

plastic

L_ hose