KitchenAid KEWS105SPA00, KEWS175SSS02, KEWS175SSS03, KEWS175SPA03, KEWS175SSS00 Installation Guide

INSTALLATIONINSTRUCTIONS

24" (61 CM), 27" (68.6 CM), AND 30" (76.2 CM)

INDOOR/OUTDOOR ELECTRICWARMING DRAWER

INSTRUCTIONSD'INSTALLATION

TIROIR-RECHAUD ELECTRIQUEPOUR USAGE

INTI_RIEUR/EXTI_RIEURDE

24" (61 CM), 27" (68,6 CM), ET30" (76,2 CM)

Table of Contents/Table des mati@res

WARMING DRAWER SAFETY ........................ 1

INSTALLATION REQUIREMENTS .................. 2

Tools and Parts .............................................. 2

Location Requirements ................................. 2

Electrical Requirements ................................. 3

INSTALLATION INSTRUCTIONS .................... 4

Install Warming Drawer ................................. 4

Complete Installation..................................... 4

SECURITle DU TIROIR-RleCHAUD ................. 5

EXIGENCES D'INSTALLATION ....................... 5

Outillage et pieces ......................................... 5

Exigences d'emplacement ............................ 6

Specifications _lectriques .............................. 7

INSTRUCTIONS D'INSTALLATION ................ 8

Installation du tiroir-r_chaud .......................... 8

Achever I'installation ...................................... 8

WARMING DRAWERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow
instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

iMPORTANT:

Save for local electrical inspector's use.

iMPORTANT :

A conserver pour consultation par I'(nspecteur local des installations electriques.

9763140A

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed

here.

Tools needed

• Phillips screwdriver

• Hand or electric drill

• 1%" (3.5 cm) hole saw

Parts supplied

• Four #8-18 x %" screws

• Lens (for panel ready models)
Check local codes. Check existing electrical supply. See

"Electrical Requirements."
It is recommended that all electrical connections be made by a

licensed, qualified electrical installer.

Make sure you have everything needed for correct installation. It is
the responsibility of the installer to comply with the installation

clearances specified in these instructions.
IMPORTANT: Observe all governing codes and ordinances.

• Cutout dimensions that are shown must be used. Given
dimensions provide minimum clearance with warming drawer.

• Recessed installation area must provide complete enclosure
around the recessed portion of the warming drawer.

• Grounded electrical supply is required. See "Electrical
Requirements" section.

• Electrical supply outlet should be located in the rear wall on
the upper right-hand side of the cutout or in an adjacent

cabinet. The outlet must be recessed. If the electrical outlet is
located in an adjacent cabinet, a 18/8'' (3.5 cm) minimum

diameter hole should have been drilled in the back of the
cutout or support surface to pass the power supply cord

through to the outlet.

• Warming drawer support surface must be solid, level and flush
with bottom of cabinet cutout.

For best performance results make sure the warming drawer is
leveled before completing installation. There is no way to level the

warming drawer after it has been installed. If the installation is not
level, the door may slide open or not seal tightly, allowing heat to

escape.

Product Dimensions

_--A

WARMING OVERALL RECESSED RECESSED

DRAWER WIDTH (A) WIDTH (B) HEIGHT (C)

SIZE
24" 233/4'' 221/4'' 9"

(61 cm) (60.3 cm) (56.5 cm) (22.9 cm)
27" 268/4'' 251/4'' 9"

(68.6 cm) (67.9 cm) (64.1 cm) (22.9 cm)
30" 298/4'' 281/4'' 9"

(76.2 cm) (75.6 cm) (71.8 cm) (22.9 cm)

Cabinet Dimensions

Cabinet Side View

Warreing

drawer

front

223/4"

(57=8 ern)

recessed

ven depth

(61ere)

24"

rein. cutout

depth

Support surface reust be
solid, _eveL f_ush with
bottom of cabinet cutout.

Cabinet Front View

o o

120 rout

grounded
outlet

(or Uocated

in adjacen_
cabinet) "_

WARMING CUTOUT MIN. CABINET

DRAWER SIZE WIDTH (A) WIDTH (B)

24" (61 cm) 221/2"(57.1 cm) 24" (61 cm)
27" (68.6 cm) 251/2'' (64.8 cm) 27" (68.6 cm)
30" (76.2 cm) 281/2'' (72.4 cm) 30" (76.2 cm)

Warming drawer can be installed as an indoor single or double
installation or installed under a single oven. Two warming drawers
under a single oven are shown.

NOTE: The warming drawer cannot be leveled after being
installed.

For outdoor installation follow the cutout dimensions above.
Install the outdoor warming drawer in a permanent fixture.

Custom Wood Drawer Front

If you plan to install a custom wood panel to match your cabinets,
we recommend consulting a qualified cabinetmaker or carpenter.

The back of the wood panel must be sealed to avoid moisture
damage.

Electrical Shock Hazard

Pmuginto a grounded 3 prong outlet.
Do not remove ground prong.

Do not use an adapter,
Do not use an extension cord.

Failure to follow these instructions can resumt in death,

fire, or eJectdcam shock.

IMPORTANT: The warming drawer must be electrically grounded
in accordance with local codes and ordinances, or in the absence
of local codes, with the National Electrical Code, ANSI/NFPA 70 or

Canadian Electrical Code, CSA C22.1.
If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that
the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is
required. A time-delay fuse or circuit breaker is also
recommended. It is recommended that a separate circuit
serving only this warming drawer be provided.

• The model/serial rating plate is located above the left-hand
side receiving slide. The warming drawer must be removed to
view the model/serial rating plate. See the illustration below.

A. Model/serial number plate