® 30" Freestanding and Slide-In Electric Range
PRODUCT MODEL NUMBERS
KERS807S
KESK901S
KESS907S
KESS908S
Electrical: This range is manufactured with the neutral terminal connected to the cabinet. Use a 3-wire UL listed, 40or 50amp power supply cord (pigtail). If local codes do not permit ground through the neutral, use a 4-wire power supply cord rated at 250 volts, 40 or 50 amps and investigated for use with ranges.The range can be connected directly to the fused disconnect (or circuit breaker box) through flexible or nonmetallic sheathed, copper or aluminum cable. A UL listed conduit connector must be provided at each end of the power supply cable (at the range and at the junction box). Wire sizes and connections must conform with the rating of the range. A time-delay fuse or circuit breaker is recommended.
OVERALL DIMENSIONS
Freestanding Range
B
A
F**
A.5³⁄ " (14.6 cm)
B.30" (76.2 cm)
C.41³⁄ " (106 cm) overall height with leveling legs screwed all the way in
D.36" (91.4 cm) cooktop trim height with leveling legs screwed all the way in*
D* C
G
E
E.30" (76.2 cm)
F.27¹⁄ " (69.2 cm) max. from handle to standoff at back of range**
G.Model/serial number plate (located on the right-hand side oven door trim)
*Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs.
**When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm) countertop; front of oven door protrudes 1" (2.5 cm) beyond 24" (61 cm) base cabinet.
Slide-in Range
A
F
B*
E**
A.30¹¹⁄ " (77.6 cm)
B.35 ⁄ " (90.5 cm) height to underside of cooktop edge with leveling legs screwed all the way in*
C.Model/serial number plate (located on the right-hand side oven door trim)
C
D
D30" (76.2 cm)
E. 27¼" (69.2 cm) from handle to standoff at back of range**
F.23" (58.4 cm) countertop notch to rear of cooktop
*Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs.
**When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm) countertop; front of oven door protrudes 1³⁄" (4.4 cm) beyond 24" (61 cm) base cabinet.
SLIDE-IN RANGE COUNTERTOP PREPARATION
The cooktop sides of the slide-in range fit over the cutout edge of your countertop.
If you have a square finish (flat) countertop and the opening width is 30" (76.2 cm), no countertop preparation is required.
Formed front-edged countertops: Must have molded edge shaved flat 3/8" (1.0 cm) from each front corner of opening.
Tile countertops may need trim cut back 3/8" (1.0 cm) from each front corner and/or rounded edge flattened.
If countertop opening width is greater than 30" (76.2 cm), adjust the 3/8" (1.0 cm) dimension.
Countertop must be level. Place level on countertop, first side to side; then front to back. If countertop is not level, range will not be level. Range must be level for satisfactory baking performance.
30"
(76.2 cm) ³⁄ "
(1.0 cm)
30 ³⁄ "
(78.1 cm)
CABINET OPENING DIMENSIONS
Freestanding Range
|
|
|
|
|
|
|
|
|
|
Cabinet opening dimensions shown are for |
||||||||||
|
|
13" (33 cm) |
|
|
|
|
25” (64 cm) countertop depth, 24” (61 cm) |
|||||||||||||
|
|
|
|
|
|
base cabinet depth and 36” (91.4 cm) |
||||||||||||||
|
|
upper cabinet |
|
For minimum |
|
|||||||||||||||
|
|
|
depth |
|
clearance |
to the |
|
countertop height. |
|
|
||||||||||
|
|
|
30" (76.2 cm) min. |
top of the |
cooktop, |
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
see NOTE*. |
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
opening width |
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
Slide-in Range |
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
30" |
|
|
|
|
|
|
|
|
|
13" (33 cm) |
|
|
||||
|
|
|
|
(76.2 cm) |
min. |
|
|
|
|
|
|
|
|
|
For minimum |
|||||
|
|
|
|
opening width |
|
|
|
|
|
|
|
|
upper cabinet |
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
clearance to the |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
depthC |
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
top of the cooktop, |
|
|
|
|
|
|
|
|
|
|
|
|
|
30" |
(76.2 cm) min. |
|
see NOTE*. |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
opening width |
22 3/4" (57.8 cm) |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
opening depth |
|
|
|
|
|
|
|
|
|
|
|
|
1/4" |
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
Cabinet door |
|
|
|
|
|
|
|
|
(6.2 cm) radius |
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
both corners |
|
|
|
||||
|
|
|
|
or hinge |
|
|
|
|
|
|
|
|
|
|
|
|
||||
Junction box - 8" |
|
|
|
|
|
|
|
30" |
|
|
|
|
||||||||
|
should not |
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
(76.2 cm) |
min. |
|
|
||||||
(20.3 cm) to 22" (55.9 cm) |
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
extend into |
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
opening width |
|
|
||||||||
from either cabinet, 7" |
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
the cutout. |
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
(17.8 cm) max. from floor |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NOTE: 24" (61 cm) min. when bottom of wood or metal cabinet is protected by not less than 1/4" (0.64 cm) flame retardant millboard covered with not less than
No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) min. clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet.
If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.
|
Cabinet door |
|
Junction box - 8" |
or hinge |
|
should not |
||
(20.3 cm) to 22" (55.9 cm) |
||
extend into |
||
from either cabinet, 7" |
||
the cutout. |
||
(17.8 cm) max. from floor |
||
|
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation |
WI0118260 |
Instructions packed with product. Specifications subject to change without notice. |
09-05-07 |