KITCHENAID KECD807XBL, KECD807XSS, KECD867XBL, KECD867XSS Dimension Guide

A. 28⁷⁄₈" (73.4 cm) maximum on 30" (76.2 cm) models 34⁹⁄₁₆" (87.8 cm)

maximum on 36" (91.4 cm) models

B. 21¹⁄₈" (53.7 cm) maximum on both 30" (76.2 cm) and 36"

(91.4 cm) models

C. 8¹⁹⁄₃₂" (21.8 cm) on 30" (76.2 cm) models 15⁷⁄₁₆"

(39.2 cm) on 36" (91.4 cm) models

D. 6¹⁹⁄₆₄" (16.0 cm) on both 30" (76.2 cm) and 36"

(91.4 cm) models

E. 2" (5.1 cm) minimum space to front

edge of cooktop F. Floor exhaust option G. 6¹⁄₈" (15.6 cm) for 6"

(15.2 cm) vent system

5¹⁄₈" (13 cm) for 5"

(12.7 cm) vent system H. 8¹⁹⁄₃₂" (21.8 cm) on 30"

(76.2 cm) models

15⁷⁄₁₆" (39.2 cm) on

36" (91.4 cm) models I. 16" (40.6 cm) on both

30" (76.2 cm) and 36"

(91.4 cm) models J. Wall exhaust option

30" (76.2 CM) AND 36" (91.4 CM) ELECTRIC DOWNDRAFT COOKTOP

PRODUCT MODEL NUMBERS CUTOUT DIMENSIONS

KECD807X KECD867X

A 4-wire or 3-wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply on a separate, 40-amp circuit breaker is required for both 30" (76.2 cm) and 36" (91.4 cm) models. If a fused system is used, fuse both sides of the line.

PRODUCT DIMENSIONS

ELECTRICAL REQUIREMENTS:

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.

Ref. W10439665A

12-13-11

Page 1 of 2

30" (76.2 cm) Cooktop - for standard and electric models

36" (91.4 cm) Cooktop - for standard and electric models

A. Model/serial rating/clearance plate location B. 21" (53.4 cm) screw head to screw head C. 22" (52.3 cm) without stainless steel trim or

21³⁷⁄₆₄" (54.8 cm) with stainless steel trim

A. 29³⁄₄" (75.6 cm) B. 12¹⁄₂" (31.8 cm)

centerline of product to

edge of burner box C. 12¹⁄₂" (31.8 cm) D. 28³⁄₈" (72.1 cm)

E. 12¹⁄₂" (31.8 cm) F. 2" (5.1 cm) recommended minimum

cabinet to motor clearance G. 18" (45.7 cm) H. 4⁵⁄₈" (11.8 cm)

A. Model/serial rating/clearance plate location B. 21" (53.4 cm) screw head to screw head C. 22" (52.3 cm) without stainless steel trim or

21³⁷⁄₆₄" (54.8 cm) with stainless steel trim

A. 35¹¹⁄₃₂" (89.8 cm) B. 12⁷⁄₈" (32.8 cm) centerline of

product to edge of burner box C. 12⁷⁄₈" (32.8 cm) D. 34¹⁄₈" (86.7 cm)

E. 12¹⁄₂" (31.8 cm) F. 8 ¹⁷⁄₆₄" (20.9 cm)

recommended minimum

cabinet to motor clearance G. 18" (45.7 cm) H. 4⁵⁄₈" (11.8 cm)

CABINET DIMENSIONS

A. 30" (76.2 cm) on 30" (76.2 cm) models 36" (91.4 cm) on 36" (91.4 cm)

models B. Combustible area above countertop (shown by dashed box above) C. 30" (76.2 cm) minimum clearance between top of cooktop platform and

bottom of uncovered wood or metal cabinet (24" [61 cm] minimum

clearance if bottom of wood or metal cabinet is covered by not less

than ¹⁄₄" [0.6 cm] flame retardant millboard covered with not less than

No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless steel, or 0.024"

[0.06 cm] aluminum or 0.020" [0.05 cm] copper) D. 13" (33 cm) recommended upper cabinet depth E. 2" (5.1 cm) F. 2 1 ¹⁄₈" (73.4 cm) G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop

within minimum horizontal clearances to cooktop H. Junction box or outlet; 12" (30.5 cm) minimum from bottom of

countertop I. Junction box or outlet; 10" (25.4 cm) from right-hand side of cabinet J. 28⁷⁄₈" (73.4 cm) on 30" (76.2 cm) models 34⁹⁄₁₆" (87.8 cm) on 36"

(91.4 cm) models

K. 2¹⁄₂" (6.4 cm) minimum distance to nearest left and right side

combustible surface above cooktop L. 1¹⁄₂" (3.8 cm) minimum clearance between back wall and countertop

NOTES: After making the countertop cutout, some installations may require notching down the base cabinet side walls to clear the cooktop base. To avoid this modification, use a base cabinet with sidewalls wider than the cutout.

●

A minimum side clearance of 6" (15.2 cm) is recommended between side of cooktop and side wall for maximum ventilation performance.

●

A minimum clearance of 2" (5.1 cm) is recommended between the motor/blower and cabinet for proper cooling. A 6" (15.2 cm) clearance is recommended for servicing access.

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.

Ref. W10439665A

12-13-11

Page 2 of 2