KitchenAid KECD865HBT0, KECD805HBL3 Installation Guide

[] []

ui

C

Readandsa_ethese

IMPORTANT:
Installer: Leave installation

Instructions with the homeowner.
Homeowner: Keep Installation

Instructions for future reference.
Save installation Instructions for local

electrical inspector's use.

KJtchen_kJd _

FORTHE WAY IT'S MADE _'

Write down the model and serial numbers
before installing cooktop.

Both numbers are on the model/serial
rating plate, located on the bottom of the

cooktop.
Model #

Serial #

Questions regarding features,
operation, performance, parts or
service? Call 1-800-422-1230 or visit

our web site at www.kitchenaid.com

Part No. 3192516

Before youstart...

Your safety and the safety of
others is very important.

We have provided many important
safety messages in this manual and

on your appliance. Always read and
obey all safety messages.

symbol.This symbol alerts

!_ This is the safety alert

you to hazards that can kill
or hurt you and others. All safety
messages will be preceded by the
safety alert symbol and the word

"DANGER" or "WARNING". These
words mean:

You will be killed or seriously
injured if you don't follow

instructions.

You can be killed or seriously
injured if you don't follow

instructions.

All safety messages will identify the
hazard, tell you how to reduce the
chance of injury, and tell you what
can happen if the instructions are

not followed.

Important: Observe all governing

codes and ordinances. Failure to meet
codes and ordinances could lead to

fire or electrical shock.

Proper installation is your responsibility.

• Make sure you have everything
necessary for correct installation.

• Have a qualified technician install
this cooktop,

• Comply with the electrical specifications
on the model/serial rating plate.
Model/serial rating plate is located on
the bottom of the cooktop. Write both

numbers down on the front cover now
before installing cooktop.

Downdraft cooktop location should be
away from strong draft areas, such as
windows, doors and strong heating vents
or fans. Locate cooktop for convenient

use in kitchen.

Grounded electrical system is required.

See "Electrical requirements," Page 6.
Venting system must terminate

outdoors.

All openings in the wall or floor where
cooktop is to be installed must be

sealed.

It is the customer's responsibility to

contact a qualified electrical installer,
to make sure that the electrical

installation is correct, and to make
sure the electrical installation follows

the National Electrical Code,
ANSI/NFPA 70 -- latest edition*, or
CSA Standards C22.1-94, Canadian

Electrical Code, Part 1 and C22.2 No.
0-M91 - latest edition**, and all local

codes and ordinances.

WARNING: To reduce the risk of fire,
electric shock, or injury to persons,

observe the following:

Installation work and electrical wiring
must be done by qualified person(s) in
accordance with all applicable codes
and standards, including fire=rated

construction.
Sufficient air is needed for proper

combustion and exhausting of gases
through the flue (chimney) of fuel

burning equipment to prevent back
drafting. Follow the heating equipment

manufacturer's guideline and safety
standards such as those published by

the American Society for Heating,

Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local
code authorities.

When cutting or drilling into wall or
ceiling, do not damage electrical wiring

and other hidden utilities.

Ducted fans must always be vented to
the outdoors.

WARNING: To reduce the risk of fire,
use only metal ductwork.

This downdraft eooktop is Not approved

for use in mobile homes.

Copies of the standards listed may be
obtained from:

* National Fire Protection Association

Batterymareb Park
Quincy, Massachusetts 02269

** Canadian Standard Association

178 Rexda_e Boulevard
Etobicoke, (Toronto), Ontario Mgw 1R3

Toolsandmaterialsneededfor installation: Partssupplied:

Phillips _:: _ I"\, pliersjj/' • _iterature pack

screwdriver // ._ :::::9 _ safety \'k_j • vent cover

,/ i¢J glasses

_¢:_yi_: metal • gBase cteaner

...._ stops , '_)

Not shown:
. wall or roof cap {not supplied)

* metal vent

. twist=on connectors and 1/2" UL=listed conduit

connector. Number and size witt depend on your

installation. See "E_eetdca_ connection," Page 7.

Product Dimensions Cutout Dimensions

21-1.!
(54.4 cm)

depth

-15/16"
ram)

burner box

depth

Couetertopmust be

supported within

3" (7.6 cm) of cutout.

14-5/8"(37.1cm)

blowerhousing

depth

3-ft.(91.4cm long

powersupplycable

factoryinstalled.

ClearanceDimensions

30" (76.2 cm) man - 30" (76.2 cm) caoktop

36" (91.4 cm) nile - 36" (91.4 cm) cooktop

when higher thee 18" (45.7 cm) -4,_ I

/ I

See Note ** for

minimum clearaeces

to nearest combustible \\ Do Not seal
vertical surface ._ caoktapto caoetertap._..._

extendieg 18" (4&7 cm) " _ ..
above caoktap _. "-.

1"

- ".........................................(25.4 rare) _-_.

29-1/2" (74.9 cm) - 36" (7&2 cm) cooktop
35-1/2" (9&2 crn) - 36" (61.4 cm) cooktop

Side clearance-- 6" (15.2 cm) minimum clearance between side
of cooktop and side wall is recommended for maximum
ventilation performance.

Rear clearance -- 3/4" (19.1 ram) clearance between rear edge of
cooktop and rear wall is recommended.

Motor/blower clearance -- 2" (51 ram) minimum clearance
between motor and cabinet is required for proper cooling.

6" (15.2 cm) clearance is recommended for servicing access.

_ Note: 24" (61 era) rainiraura when bottora of wood or rectal cabinet is

protected by not less than 1/4" (6.4 tara) flarae retardant raiJiboard covered
with not Jessthan No. 28 MSG sheet steel, 0.015" (0.4 rare} stainless stee_,

0,024" (0,6 rata) aJurainura or &020" (0,5 rata} copper,

30" (76,2 cra) rainiraura clearance between the top of the cooking p_atforra

and bottom of unprotected wood or sheet metal

cutout width

coaetertop

\

\

install rear
wall junction

box in shaded
area. Darker
shaded area is

preferred.

7

floor

11" (27.g cm) 6" (2&3 cm)

Minimum base cabinet dimensions --

30" (76.2 cm) base cabinet width
24" (61 cm) base cabinet depth
25" (63.5 cm) countertop depth

Countertop opening dimensions that are shown must
be used. Given dimensions are minimum clearances and

provide required 0" (0 cm) clearance.

New installations -- Follow minimum dimensions given:

Replacement installation -- Be sure that front edge of
cooktop is at least 1=1/2" (38.1 mm) back from front
edge of countertop.

tf cabinet has drawers, drawers will need to be
removed and drawer fronts installed on front of cabinet.

Cutout preparation:

Decorative laminate --
Chamfer all exposed edges to

prevent chipping laminate,

Cut radius corners and file to
smooth edges and to prevent

cracking.