KitchenAid KECD865HWH3, KECD865HWH2, KECD865HBT2, KECD865HBT3, KECD865HBL05 Installation Guide

...

[] []

Readandsavethese

IMPORTANT: Installer: Leave installation

Instructions with the homeowner. Homeowner: Keep Installation

Instructions for future reference. Save Installation Instructions for local

ebctrical inspector's use.

KJtchen_kJd _

FORTHE WAY IT'S MADE _'

Write down the model and serial numbers before installing cooktop.

Both numbers are on the modeVserial rating plate, located on the bottom of the

cooktop. Model #

Serial #

Questions regarding features, operation, performance, parts or service? Call 1-800o422-1230 or visit

our web site at www.kitchenaid.com

Part No. 8285364

Before youstart,,,

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and

on your appliance. Ah_iays read and obey all safety messages.

This is the safety alert symbol.This symbol alerts you to hazards that can kill

or hurt you and others. All safety messages will be preceded by the safety alert symbol and the word

"DANGER" or "WARNING". These words mean:

You witi be killed or seriously

injured if you don't foltow instructions.

You can be killed or seriously

injured if you don't foltow instructions.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are

not followed.

Important: Observe all governing codes and ordinances. Failure to meet

codes and ordinances could lead to fire or electrical shock.

To eliminate the risk of burns by reaching over heated surface units,

cabinet storage space located above the surface units should be avoided, tf

cabinet storage is to be provided, the

risk can be reduced by instalJing a range hood that projects horizontaJiy a minimum of 5 inches (12.7 am) beyond

the bottom of the cabinets.

Proper installation is your responsibility. oMake sure you have everything

necessary for correct installation.

oHave a qualified technician install

this cooktop.

• Comply with the electrical specifications on the model/serial rating plate. Model/serial rating plate is located on

the bottom of the cooktop. Write both numbers down on the front cover now

before installing cooktop.

Downdraft cooktop location should be away from strong draft areas, such as windows, doors and strong heating vents or fans. Locate cooktop for convenient

use in kitchen.

Grounded electrical system is required=

See "Electrical requirements," Page 6= Venting system must terminate

outdoors.

AH openings in the wall or floor where cooktop is to be installed must be

sealed.

tt is the customer's responsibility to contact a qualified electrical installer,

to make sure that the electrical

installation is correct, and to make sure the electrical installation follows

the National EJectrical Code, ANSJ/NFPA 70 -- latest edition*, or

CSA Standards C22.1=94, Canadian

EJectrical Code, Part 1 and C22.2 No.

0-M91 =latest edition**, and aH local codes and ordinances.

WARNING: To reduce the risk of fire, electric shock, or injury to persons,

observe the following:

installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated

construction. Sufficient air is needed for proper

combustion and exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent back drafting. Follow the heating equipment

manufacturer's guideline and safety standards such as those published by

the American Society for Heating,

Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code authorities.

When cutting or drilling into wall or ceiling, do not damage electrical wiring

and other hidden utilities.

Ducted fans must always be vented to the outdoors.

WARNING: To reduce the risk of fire, use only metal ductwork.

This downdraft eooktop is Not approved

for use in mobile homes.

Copies of the standards listed may be obtained from:

* National Fire Protection Association

Batterymareh Park Quincy, Massachusetts 02269

** Canadian Standard Association

178 Rexdale Boulevard Etobicoke, (Toronto), Ontario Mgw 1R3

Toolsandmaterials neededfor installation:

PhHHps _, pliers ji

screwdriver // ._ :_:_ safety \_ ;_'Y.:j glasses

...._ snips , _'_

Not shown: . wall or roof cap {not supplied)

. metal vent . twist=on connectors and 1/2" UL=iisted conduit

connecter, Number and size will depend on your

installation. See "E_eetriea_ connection," Page 7.

Partssupplied:

* literature pack * vent cover

* glass cleaner

Product #[mens[ens

Cateat #imensiens

J_qr-_. 31-1/2" (88 cm) - 38" (76.2 cm) ceohtep

37-1/2" (95.3 cm) - 36" (91.4 cm) cooktop

14-5/8" (37.1 cm)

blower housing

depth

Clearancegimensiens

38" (76.2 cm) rain - 38" (76.2 cm) caoktop

36" (91.4 cm) rain - 36" (91.4 cm) cooktop

whee higher thee 18" (45.7 cm) _1

width

3-ft. gl.4 cm long

power snpp y cab e

factory installed.

29-112" (74.9 cm) - 38" (76.2 cm) ceoktop 35-1/2" (98.2 cm) - 36" (91.4 cm) ceoktep

Select required duct cotont

(see Page 4 for exhaust duct

cutoutlocation}.

install rear wall junction

box in shaded area. Darker shaded area is

preferred.

cnteat width

cauntertap

fleer

2"(5,1 cm)minh_nm spacetofrontedge of

cenetertep

Oouetertapmust he supported within

3" (7.6 cm) of cutout.

5" (12.7 era)

11" (27.9 cm) 8" (28.3 cm)

cm)

_pth

See Note ** [or

minimum clearances

Minimum base cabinet dimensions --

30" (76.2 cm) base cabinet width 24" (61 cm) base cabinet depth 25" (63.5 cm) countertop depth

".. %.,

Nieimum distance "'..\ .... _. ---.21"_ (53.3 cm)

te nearestcombustibleS..\ \\_ uo !.Jptseal ,_,,_n_._ opeeing depth

vertical suflace "...._ _ ceo,'{mpto ceante_mp. "_._ _

extendieglS"(45,7cm) _,,', "" _-- --

ohovecoo,top _. ....--_\ \ _................................

29-1/2" (74.9 cm) - 38" (76.2 cm) cooktop 35-1/2" (98.2 cm) - 36" (91.4 cm) ceoktop

Side cJearance-- 6" (15.2 cm) minimum clearance between side

cuton_width

Countertop opening dimensions that are shown must be used. Given dimensions are minimum clearances and

provide required 0" (0 cm) clearance.

New installations -- Follow minimum dimensions given.

Replacement installation -- Be sure that front edge of cooktop is at least 1-1/2" (38.1 mm) back from front edge of countertop.

ff cabinet has drawers, drawers will need to be removed and drawer fronts installed on front of cabinet.

of cooktop and side wall is recommended for maximum ventilation performance.

Rear cJearance- 3/4" (19.1 mm) clearance between rear edge of cooktop and rear wall is recommended.

Motor/b_ower c_earance-- 2" (51 mm) minimum clearance between motor and cabinet is required for proper cooling.

6" (15.2 cm) clearance is recommended for servicing access,

_ Note: 24" {61 era) rainiraura when bottom of wood or rectal cabinet is

protected by not _essthan 1/4" (&4 rare) florae retardant rag_board covered with not Jessthan No. 28 MSG sheet steel 0.015" {0.4 ram) stainless steel

0,024" (0,6 rare) alurainura or 0,020" (0,5 rare) copper,

30" (7&2 era) rainiraura cJearanee between the top of the cooking p_atfotra

and bottom of unprotected wood or sheet metal

Cutout preparation:

Decorative laminate -- Chamfer all exposed edges to

prevent chipping laminate,

Cut radius corners and file to smooth edges and to prevent

cracking.

+ 5 hidden pages