KitchenAid KEBS208DWH9 Installation Instruction

Installation Instructions

30" Electric

Built-in Single and

Double Ovens

IMPORTANT:

Read and save these instructions.

Part No. 4450411 Rev. A

Quick Reference

Table of Contents:

Pages

1 Product dimensions

1 Cutout dimensions

1Before you start

2Electrical requirements

2 3 Installation steps

If you need assistance:

Check your Use and Care Guide for a toll-free number to call or call the dealer from whom you purchased this appliance. The dealer is listed in the Yellow Pages of your phone directory under “Appliances — Household — Major — Service and Repair.”

Call when you:

Have questions about built-in oven installation or operation.

Need to obtain the name and number of an authorized service company.

When you call, you will need:

The built-in oven model number.

The built-in oven serial number.

Both numbers are listed on the model/serial rating plate, located on the oven door or on the oven frame.

IMPORTANT:

Installer: Leave Installation Instructions with the homeowner.

Homeowner: Keep Installation Instructions for future reference.

Save Installation Instructions for local electrical inspector's use.

KitchenAid KEBS208DWH9 Installation Instruction

Product dimensions

Single oven Double oven

28-3/8" max.

28-3/8" max.

recessed width

recessed

 

width

 

27-1/2"

29" max.

 

overall

 

recessed

height

51" max.

height

 

 

overall

 

 

 

 

height

 

 

49-1/2"

 

 

recessed

 

 

height

23" max.

29-3/4"

 

recessed

overall width

 

23" max.

29-3/4"

overall width

recessed

 

depth

Cutout dimensions

 

 

 

 

 

30" min.

 

 

 

cabinet

 

 

 

1" top of cutout

 

 

 

to bottom of

 

 

 

upper cabinet

 

 

 

door

30" min.

 

 

 

cabinet width

 

 

 

 

 

49-3/4"

 

 

1-1/2" min.

min.

28-1/2"

 

cutout

 

top of cutout

cutout

 

height

 

to underside

width

 

 

 

of countertop

 

 

27-3/4"

 

 

 

min.

 

 

 

cutout

 

 

 

height

 

 

 

 

 

1-1/2" min.

14-3/4"

 

 

bottom

 

 

bottom of

 

 

of cutout

 

 

cutout to top of

 

 

to floor

28-1/2"

 

cabinet door

5-1/4" bottom of

 

cutout width

 

 

 

cutout to floor

 

 

Single oven

Double oven

undercounter

(without cooktop installed above)

30" min. cabinet width

27-3/4"

min.

cutout

height

1-1/2"

min.

bottom of

cutout to

top of

cabinet

door

1" top of cutout to bottom of upper cabinet door

28-1/2" cutout width

32" bottom of cutout to floor

Single oven

Page 1

 

23-1/4" min.

 

 

cutout depth

 

 

23" recessed

 

 

oven depth

 

cabinet

recessed

oven

oven

front

 

Cabinet side view

Cabinet filler kits are available from your dealer. Use a matching color kit if oven is smaller than your cabinet opening.

Single oven filler height is 3-5/16"

Black — 4378941

White — 4378942

Almond — 4378943

Double oven filler height is 6-5/16"

Black — 4378947

White — 4378948

Almond — 4378949

Before you start...

Important: Observe all governing codes and ordinances.

Proper installation is your responsibility. Have a qualified technician install this oven.

Oven location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

Recessed installation area must provide complete enclosure around the recessed portion of the oven.

Electrical ground is required. See “Electrical requirements.”

Electrical supply junction box should be located 3 inches maximum below the support surface when oven is installed in a wall cabinet. Drill a 1-inch minimum diameter hole in the right rear or left rear corner of the support surface to pass the appliance cable through to the junction box. For undercounter installation, it is recommended that the junction box be located in the adjacent right or left cabinet. If installing the junction box on rear wall behind oven, junction box must be recessed and located in the upper or lower right or left corner of cabinet.

Oven support surface MUST be solid, level and flush with bottom of cabinet cutout.

It is the customer’s responsibility:

To contact a qualified electrical installer.

To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 — latest edition*, and all local codes and ordinances.

Copies of the standards listed may be obtained from:

*National Fire Protection Association Batterymarch Park

Quincy, Massachusetts 02269

Tool needed:

Phillips screwdriver

Parts supplied:

oven)

Note: If installing a single oven, you will need only two screws and two door removal pins.

Loading...
+ 3 hidden pages