KitchenAid KEBC247KWH04, KEBC147KSS05, KEBC247KWH0, RBS245PDT18, RBS245PDT12 Installation Guide

ii_i _i _ _ i i i_ _i iilili

Quick Reference

TabJe ef Contents:

Pages

[_ Product dimensions
[_ Cutout dimensions

[_ Before you start
[_ Electrical requirements

[_ _ Mnstallation steps

Jf you need assistance:

Check your Use and Care Guide for a toll-free number to call or call

the dealer from whom you purchased tMs appliance. The dealer is

listed in the Yellow Pages of your phone directory under

"Appliances -- HousehoH -- Major -- Service and Repair."

Ca[[when you:
[_ Have questions about built-in oven installation or operation.

[_ Need to obtain the name and number of an authorized service

company.

When you call, you will need:
[_ The built-in oven mode[ number.

[_ The built-in oven serial number.
Both numbers are listed on the model/serial rating plate, located on

the oven door or on the oven frame.

23-3/4"

/----"J_overallwidth

49=1/2"

recessed

height

DoubUe oven

22=3/8"raax,

recessed width

j_

J

51" raax,

overall

height

/

Your safety andthe safety of others are

very important,

We have provided many important safety

messagesinthis manualand on your appliance.

Atways read and obeyaIIsafety messages.

This is the safety alertsymbol,
Thissymboi alertsyou to potential hazards

that can kiii or hurt you and others,

Ati safety'messageswiii foiiow the safetyalert
symbo! andeitherthe word "DANGER"or

"WARNING",Thesewords mean:

You canbekilledorseriouslyinjuredifyoudon't

follow instructions.
Ati safety messageswiii teii you what the potential

hazardis, toil you howto reducethe chance of
injury, andteli you what can happenif the

instructions are not foiiowed.

27=3/4"

rain,

cutout

height

24" rain,

cabinet width

22=1/2"

cutout width

Single oven

undercounter

(without cooktop

installed above)

_--cabinetwidth--

24"rain,

1=1/2"rain.

top ofcutout
to underside

of countertop

5=1/4" bottom of

cutout to floor

23"raax,
recessed

depth

T

49=3/4"

rain.

cutout

height

1=1/2" rain,

bottom of

cutout to top of

cabinet door

23=3/4"

"_--- cabinet -_"

24" rain,

4-- cutout ---_

22=1/2"

width

Doable oven

width

1" top ot cutout

to bottora of

upper cabinet

door

14=3/4"

bottora

of cutout

to floor

important: Observe all governing codes

and ordinances.

Proper installation is your responsibility.
Have a qualified technician install this oven.

Oven location should be away from strong draft

areas, such as windows, doors and strong
heating vents.

Cabinet opening dimensions that are shown

must be used. Given dimensions provide
minimum clearance.

Recessed installation area must provide

complete enclosure around the recessed portion

of the oven.
Electrica_ground is required. See "Electrical

requirements."
EJectrica_supply junction box should be located

3 inches maximum below the support surface
when oven is installed in awall cabinet. Drill a

1°inch minimum diameter hole in the right rear
or left rear corner of the support surface to pass

the appliance cable through to the junction box.

For undercounter installation, it is recommended

that the junction box be located in the adjacent

right or left cabinet. If installing the junction box
on rear wall behind oven, junction box must be
recessed and located in the upper or lower right

or left corner of cabinet.

Oven support surface MUST be solid, level and
flush with bottom of cabinet cutout.

it is the customer's responsibility:

To contact a qualifiedelectrical installer.
To assure that the electrical installation is

adequate and in conformance with National

Electrical Code, ANSl/NFPA 70 _ latest edition*,

and all local codes and ordinances.

Copies of the standards _isted may be obtained from:
* National Fire Protection Association

Batteryraarch Park
Quincy, Massachusetts 02269

[

27=3/4"

rain.

cutout
height

1=I/2"

botteraef

cutoutto

top of

cabinet

rain.

door

_--- cutout ---_

22=I/2"

width

Singmeoven

l"topefcuteut

to botteraef

upper cabinet

door

32 _

bottom of

cutout to

floor

cabinet_---

23=l/4"rain.

cutout depth

23"recessed

even depth

recessed

oven

Cabinet side view

oven

/_ front

Tool needed:

Z

screwdriver

Partssupplied:

4 screws (double oven)

Page 1

_fcodespermitandaseparategroundingwireis
used,it isrecommendedthataqualifiede_ectrician

determine that the grounding path and wire gauge
are in accordance with toca_ codes.

Do Not ground to a gas pipe.
Check with a qualified electrician if you are not

sure oven is proper_y grounded.
Do Not have a fuse in the neutral or grounding

circuit.

Oven must be connected to the proper eUectdcaU
voUtageand frequency as specified on the
modeU/sedd rating plate. (The model/serial rating

plate is located on the oven door or on the oven
frame.}

[_ Models rated from 7.3to 9.6 kW at 240 volts
(5.5to 7.2 kW at 208 volts) require a separate

@-ampere circuit. Models rated at 7.2 kW and
below at 240 volts (5.4 kW and below at 208

volts) require a separate 30-ampere circuit.

[_ A time-delay fuse or circuit breaker is
recommended.

[_ Connect directly to the fused disconnect (or
circuit breaker box} through flexible, armored
or non-metallic sheathed, copper cable (with
grounding wire}.

[_ Flexible armored cable from appliance should
be connected directly to junction box.

[_ Fuse both sides of the line.
[_ A U.L.qisted conduit connector must be

provided atthe junction box.
[_ Do Not cut the conduit.
Wire sizes and connections must conform with the

rating of the appliance and to the requirements of

the National Electrical Code, ANSI/NFPA 70 -- latest

edition (% See Page 1) and all local codes and
ordinances.

if the house has aluminum wiring, follow the
procedure below.

a.} Connect the aluminum wiring to the copper wire

using special connectors designed and
Underwriters Laboratories-listed for joining
copper to aluminum. Follow the electrical

connector manufacturer's recommended
procedure.

b.} Aluminum/copper connection must conform

with local codes and industry-accepted wiring

practice.

Grasp oven

frame to li_

oven.

Preparation

(

Use screws to attach
oven to cabinet.

Grasp oven

Remove trim

screws.

Remove
oven door.

Reattach side frame to lift

trim. oven.

Remove

trim screws.

Remove side

trim.

Use screws to
attach oven to
cabinet.

Excessive Weight Hazard

Use two or more people to move and
install oven.

Failure to follow this instruction can

result in back or other injury.

Important: Use both hands to remove oven
doors.

Do Not use handb or any portion of the front

frame or trim for lifting.

Before moving oven across floor, check that oven
is on shipping base or slide oven onto cardboard

or hardboard.
Do Not remove shipping feet at the front tower

corners of oven.

match on the hinge
in mocked position =
door free to open

and close

latch on the hinge

position = door
ready for removal

Pull top of trim
down,

shipping feet.

Turn power supply off. Move oven close to

final position.

Remove and discard shipping materials, tape
and protective film from the oven. Do Not

remove shipping base or shipping feet at the
front bwer corners of oven. The shipping feet
will protect the Jower oven trim unti_ oven is

inserted into cabinet.

, Remove and set aside racks and other parts

from inside oven.

Page 2

m Completely open oven door. In both back
corners of the door you will see door latches in the
locked position. Rotate both latches forward to the
unlocked position.

Grasp outside edges of door with both hands.

• Begin closing door, atthe moment the door
stops closing, lift and puii door toward you.

, Set door aside on a protective surface.

3m Remove trim screws attaching right and
left side trim to oven. Grasp the bottom end of

trim and pull away from oven. Slide top end of
trim downward to remove trim from oven. Take

care not to scratch other surfaces with ends of

trim. Set trim and screws aside on protected

surface.

Electrical connection

If your house has aluminum wiring, see
"Ebctrical requirernents", Page 2.

Electrbal Shock Hazard

Turn power supply off before connecting wires.

Use 8 gauge solid copper wire.
Electrically ground range.

Failure to follow these instructions can result

in death, fire, or electrical shock.

This oven is manufactured with white {neutraJ)

power supply wire and a cabinet=connected bare
grounding wire twisted together.

Feed oven cane through opening in
the cabinet. Make electrical connection

following the steps needed for your installation.

1. Disconnect the power supply.

2. Remove the junction box cover.

3. Connect oven cable to junction box through the
U.L.-listed conduit connector.

4. Connect the two black wires together with

twist-on connectors.

5. Connect the two red wires together with

twist-on connectors.

6. Complete electrical connection according to
local codes and ordinances.

cable from

junction power supply

box _

re.,_

white _ -:_

w,re _ _>_

grounding oven
cable wires --

factory crimped

Figure 1 cable from

oven

ff local codes PERMIT

connecting cabinet-grounding

conductor to neutral white

wire in junction box:

7. Connect the factory-crimped
bare and white oven cable wires

to the neutral (white) wire in
junction box. See Figure 1.

8. Replace junction box cover.

conduit

connector

iunction power supply

Figure 2

cabb from

cabte from connector
oven

If local codes DO NOT PERMIT
connecting cabinet-grounding

conductor to neutral white

wire in junction box:

7.

Separate the factory-crimped
bare and white oven cable wires.

8. Connect white oven cable wire to
neutral (white) wire in junction

box. See Figure 2.

9. Connect the bare grounding
oven cable wire to a grounded
wire in the junction box. See
Figure 2.

10. Replace junction box cover.

If connecting to a

four-wire electrical system:

7. Separate bare and white oven
cable wires.

8. Connect white oven cable wire

to neutral (white) wire in
junction box. SeeFigure 2.

9. Connect the bare grounding
oven cable wire to the green
grounding wire in junction box.
Do Not connect bare grounding

wire to neutral {white} wire in

junction box. SeeFigure 2.

10. Replace junction box cover.

Attachment

Carefully push against sea_area of oven front
frame when pushing oven into cabinet.

Do Not push against outside edges.

5[] Lift oven into cabinet cutout using the

oven opening asan area to grip.

shipping
foot

Push against seal area of front frame to push
oven into cabinet until shipping feet almost

contact cabinet. Use a Phillips screwdriver to

remove screws attaching shipping feet. Remove
and discard shipping feet.

Push oven completely into cabinet and center
oven in cabinet cutout.

4 screws

6[] Important: Securely fasten oven to cabinet
using the screws provided (two screws for a single

oven or four screws for a double oven). Insert the
screws through holes in mounting rails. Do Not

overtighten screws.

Slide top
of trim up.

Push trim

into place.
Repmace

trim screw.

/

7[] Slide top end of each trim upward onto oven

side rails. Push each trim into place at bottom of

trim. Use screws to attach each trim to oven. Take

care not to scratch other surfaces with ends of trim.

8[] Replace oven racks.

Important: Replace the door with the model/serial
rating plate on the upper oven.

On some models, the construction of this door is
designed to withstand self-cleaning temperatures.

9[] Reinstall the oven door by inserting ends
of hinges into hinge slots in the oven frame. Push

hinges in as far as they will go, Open the door
(you will feel the door drop into place) and rotate
both binge tatches back to the locked position.

Close and open the door to check that the door
closes and opens completely, if door does not
dose or open completely, repeat the door
removal step and reinstall door as described

above,

Repeat for lower oven door.

Check operation

[] Turn on power supply. The display

panel will light up briefly. "PF" should appear in

the temperature display.

Page 3

the display. Press the "START" pad. Make sure the

oven door is closed and the "ON" light is shown in

the display area. After 2minutes, partially open

oven door. You should feel heat from the oven.
Press the "CANCEL" pad.
Check the operation of your double oven.
Press the "Upper Oven" pad. Pressthe "BROIL"

pad. "BROIL" will appear in the display. Press the
"START" pad. Make sure the oven door is closed
and the "ON" light is shown in the display area.
After 2 minutes, partially open oven door. You

should feel heat from the oven. Pressthe
"CANCEL" pad.

Press the "Lower Oven" pad and repeat the steps
you completed for checking the upper oven.

If your oven does not heat or an "F", foibwed
by a number, appears in the display, contact
your dea_er or check the "ff you need service..."

section of this Installation _nstructions.

To get the most efficient use

from your new oven, read your

Use and Care Guide. Keep installation

hstructions

and Guide cmoseto oven

for easy reference.

if oven does not operate:

[_ Checkthat circuit breaker is not tdpped or

house fuse blown.

[_ See Use and Care Guide for troubleshooting list.

if you need assistance:

ff you have questions about operating, c_eaning or
maintaining your oven:

D Refer to Use and Care Guide.
[_ Callthe Consumer Assistance Center: Check

your Use and Care Guide for a toll-free

number to call or call the dealer from whom you
purchased this appliance. The dealer is listed in

the Yellow Pages of your phone directory under

"Appliances -- Household -- Major -- Service
and Repair."

If you need service:

Maintain the quality built into your built-in oven by
calling an authorized service company.

To obtain the name and number of an authorized
service company:

[_ Contact the dealer from whom you purchased

your built-in oven; or

[_ Look in the Yellow Pages of your telephone

directory under "Appliances -- Household --

Major -- Service and Repair" for an authorized

service company; or

[_ Call the Consumer Assistance Center. The toll-

free phone number is listed in your Use and
Care Guide.

When you ca[[, you wi[[ need:
[_ The built-in oven model number.
[_ The built-in oven serial number.

Both numbers are listed on the model/serial rating
plate, located on the oven door or on the oven

frame.

Part No. 8300656
© 2001 Printed in U.S.A.