KITCHENAID KDSCM 82142 (UK) User Manual
Instructions for use
Installation 4
Product description 6
First time use 7
Programs table 10
Options and functions 11
Loading the racks 12
Daily use 14
Tips 15
Care and maintenance 15
Troubleshooting 17
After-sales service 18
Before using the appliance carefully read Health and Safety guide.
MIN 40 cm
MAX 80 cm
Installation
ATTENTION: If the appliance must be moved at any time, keep it in an upright position; if absolutely
necessary, it may be tilted onto its back.
CONNECTING THE WATER SUPPLY
Adaptation of the water supply for installation
should only be performed by a qualified technician.
The water inlet and outlet hoses may be positioned
towards the right or the left in order to achieve the
best possible installation.
Make sure the dishwasher does not bend or squash
the hoses.
CONNECTING THE WATER INLET HOSE
• Run the water until it is perfectly clear.
• Screw the inlet hose tightly into position and turn
on the tap.
If the inlet hose is not long enough, contact a specialist store or an authorised technician.
The water pressure must be within the values indicated in the Technical Data table - otherwise the dishwasher may be function properly.
Make sure the hose is not bent or compressed.
SPECIFICATIONS FOR THE CONNECTION
OF THE WATER SUPPLY HOSE:
WATER SUPPLY cold or hot (max. 60°C)
WATER INTAKE 3/4”
POWER OF WATER
PRESSURE
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
CONNECTING THE WATER OUTLET HOSE
Connect the outlet hose to a drain duct with a minimum diameter of 2 cm A
The outlet hose connection must be at a height ranging from 40 to 80 cm from the floor or surface where
the dishwasher rests.
Before connecting the water outlet hose to the sink
drain, remove the plastic plug B.
ANTI-FLOODING PROTECTION
Anti-flooding protection. To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the
water supply in the event of anomalies or leaks from
inside the appliance.
Some models are also equipped with the supplementary safety device New Aqua Stop, which guarantees anti-flooding protection even in the event of a
supply hose rupture.
Under no circumstances should the water inlet hose
be cut as it contains live electrical parts.
ELECTRICAL CONNECTION
WARNING: Under no circumstances
should the water inlet hose be cut as it contains live electrical parts.
Before inserting the plug into the electrical socket,
make sure that:
• The socket is earth and complies with current regulations;
• The socket can withstand the maximum load of
the appliance as shown on the data plate located
on the inside of the door (see PRODUCT
DESCRIPTION).
• The power supply voltage falls within the values
indicated on the data plate on the inside of the door.
• The socket is compatible with the plug of the
appliance.
If this is not the case, ask an authorised technician to
replace the plug (see AFTER-SALES SERVICE). Do
not use extension cables or multiple sockets. Once the
appliance has been installed, the power supply cable
and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced by the manufacturer or its authorised Technical Assistance Service in order to prevent all
potential hazards.
The Company shall not be held responsible for any
incidents, if these regulations are not observed.
4
POSITIONING AND LEVELLING
1. Position the dishwasher on a level sturdy floor. If
the floor is uneven, the front feet of the appliance
may be adjusted until it reaches a horizontal
position. If the appliance is levelled correctly, it
will be more stable and much less likely to move
or cause vibrations and noise while it is
operating.
2. Before recessing the dishwasher, stick the adhesive transparent strip under the wooden shelf in order to protect it from any condensation which may form.
3. Place the dishwasher so that its sides or back panel are in contact with the adjacent cabinets or the wall. This appliance can also be recessed under a single worktop.
4. To adjust the height of the rear foot, turn the red
hexagonal bushing on the lower central part at the
front of the dishwasher using a hexagonal
spanner with an opening of 8 mm. Turn the
spanner in a clockwise direction to increase the
height and in an anticlockwise direction to
decrease it.
DIMENSIONS, CAPACITY AND STANDBY
CONSUMPTION:
WIDTH 598 mm
HEIGHT 820 mm
DEPTH 555 mm
CAPACITY 14 standard place-settings
STANDBY
CONSUMPTION:
Left-on mode - 5 W
Off mode - 0.5 W
5
Product description
1
4
6
5
11
13
7
12
10
8
2
0000 000 00000
Service:
3
9
768
4
5 9 10 11 13121
23
14 15 16 17 18
APPLIANCE
1. Upper rack
2. Foldable flaps
3. Upper rack height adjuster
4. Upper spray arm
5. Dynamic Clean supports
6. Lower rack
7. Cutlery basket
CONTROL PANEL
1. ON/OFF button
2. PREVIOUS button
3. NEXT button
4. Multizone button
5. Display
6. Multizone indicator ligh
7. Eco program indicator light
8. Start Delay indicator light
9. Program number and remaining time indicator
10. Closed water tap indicator light
8. Lower spray arm
9. Filter Assembly
10. Salt reservoir
11. Detergent and Rinse Aid dispensers
12. Rating plate
13. Control panel
11. Rinse Aid refill indicator light
12. Salt refill indicator light
13. Tablet Detergent (All-in-one) indicator light
14. Tablet Detergent (All-in-one) button with indicator light
15. Boost button with indicator light
16. Dynamic Clean button with indicator light
17. Start Delay button with indicator light
18. START button with indicator light
6
Loading...